DESCRIPTION:
Icing Pourable Brushable Polyester Finishing Putty is the original, best selling polyester finishing putty that
spreads smoothly, self levels, and dries to an exceptionally easy to sand finish. Icing provides great adhesion and
is tack free and stain free.
PART NUMBERS:
26006 Icing 24 fl. oz. tube 6 tubes / case 12 lbs / case
26011 Icing 30 fl. oz. pumptainer bottle 6 bottles / case 16 lbs / case
Form: TDSUSC26006 PG 1 of 2 Rev: 02/11 U.S. Chemical & Plastics 600 Nova Dr. SE Massillon, OH 44646 Tel: 800-321-0672
www.USChem.com
TTEECCHHNNIICCAALL DDAATTAA SSHHEEEETT IIcciinngg
PRODUCT: Icing Pourable Brushable Polyester Finishing Putty
TECHNICAL CALLS: 1-800-321-0672
TYPICAL SUBSTRATES:
Metal Aluminum Fiberglass Body Filler Wood 2K Primers
Aged, sanded OEM Topcoats Galvanized and other zinc-coated steel
SMC can be used for cosmetic repairs. For structural repairs prone to high degrees of stress and flexibility,
use an SMC repair product. For flexible plastics use PRO-FLEX 26037.
SURFACE PREPARATION:
1. Clean surface. Remove all dirt, oil, grease and wax with a cleaning solvent such as 1240-1 Wax,
Grease & Silicone Remover.
2. Make sure surface is dry before repairing.
3. Use 80 180 grit disc to featheredge paint for good mechanical adhesion.
MIXING:
For best results, bring putty and provided hardener to room temperature (minimum temperature 68 F).
Knead hardener tube before use. Place a 4 diameter puddle of putty on a clean mixing surface (we
recommend a non-absorbent plastic mixing board) and add a ribbon of cream hardener from edge to
edge across the center of the putty puddle (puddles larger than 4 will require additional hardener); or
measure hardener at 2% by weight a 50-1 ratio. Mix thoroughly with a plastic spreader, using a folding
motion, until uniform color is achieved. At room temperature (68 F) approximate setting time is 3-5
minutes.
MIX
PRODUCT USES:
Use for minor body work and surface imperfections (1/8 thick or less) such as sand scratches, chips, scratches and
pinholes. Ideal for use as a finish coat over body filler.
APPLICATION:
1. Using a plastic spreader, apply a thin layer of putty to surface, using firm pressure for maximum
adhesion.
2. Apply additional layers, building up damaged area higher than the surrounding surface to allow for
sanding of the putty. Do not apply over fresh or uncured coatings.
FINISHING:
When material has hardened, in approximately 15 minutes, sand with 100 – 180 grit sandpaper followed by
220 – 400 grit if desired.
SPECIAL NOTES: May be intermixed with any USC Body Filler product except All-Metal.
TECHNICAL INFORMATION :
Appearance as Packaged: Off-White
VOC Packaged: 281 g/l
Applied: 2.2 g/l
Weight Per Gallon (Density): 9.5 pounds/gallon (Average)
Maximum Recommended Thickness (sanded): 1/8
Viscosity @ 77
F: 18,000 cps
Gel Time @ 77
F: 4.0 5.0 minutes
Shore D Hardness Values @ 24 hours: 55-60
Sanding Time @ 77
o
F: 15 minutes
Maximum Heat: 200 F for 30 minutes
Catalyst Required: Benzoyl Peroxide
Catalyzation Ratio: 2% by weight (50:1 ratio)
Exotherm Temperature: 220 F (Average)
Tack Free Time: 10 – 15 minutes
HEALTH & SAFETY:
Read all warnings, first aid and safety for all components before using. Keep out of reach of children and
animals. Protect hands with impervious rubber gloves. Wear face, skin and eye protection. When
sanding, we recommend the use of a respiratory covering device to protect from dust (MSA mask P/N
459029 with MSA cartridge 464029 or equivalent). When using power equipment, refer to power tool
manufacturer s recommendations for safety equipment. USC products are for industrial use by trained
professionals only.
Emergency Medical or Spill Control Information:
In U.S. or Canada call CHEMTREC at 1-800-424-9300
Form: TDSUSC26006 PG 2 of 2 Rev: 02/11 U.S. Chemical & Plastics 600 Nova Dr. SE Massillon, OH 44646 Tel: 800-321-0672
www.USChem.com
TOPCOATING:
May be topcoated with polyester, 2K urethane or 1K primer. Refer to paint manufacturer s instructions for topcoat
application.
ASSOCIATED MSDS : Putty: Icing-26014 Hardener: Cream Hardener