SAFETY DATA SHEET
Revision Date 21-Feb-2019 Version 1
1. IDENTIFICATION
Product identifier
Product Name EVERCOAT POLYESTER GLAZING PUTTY
Other means of identification
Product Code 100400_100407
Recommended use of the chemical and restrictions on use
Recommended Use Finishing Putty. For professional use only.
Uses advised against Uses other than recommended use.
Details of the supplier of the safety data sheet
24-hour emergency phone number
CHEMTREC: 1-800-424-9300
INTERNATIONAL: 1-703-527-3887
E-mail address: Info@evercoat.com
2. HAZARDS IDENTIFICATION
Classification
OSHA Regulatory Status
This chemical is considered hazardous by the 2012 OSHA Hazard Communication Standard (29 CFR 1910.1200)
Acute toxicity – Inhalation (Dusts/Mists) Category 4
Skin corrosion/irritation Category 2
Serious eye damage/eye irritation Category 2
Respiratory sensitization Category 1
Skin sensitization Category 1
Carcinogenicity Category 2
Reproductive toxicity Category 2
Specific target organ toxicity (repeated exposure) Category 1
Label elements
Emergency Overview
Manufacturer Address
ITW Evercoat
A division of Illinois Tool Works Inc.
6600 Cornell Road
Cincinnati, OH 45242 USA
513-489-7600
May Also Be Distributed by:
ITW Permatex Canada
101-2360 Bristol Circle
Oakville, ON Canada L6H 6M5
Telephone: (800) 924-6994
Flammable liquids Category 3
Signal word
Danger
_____________________________________________________________________________________________
Page 1 / 9
Harmful if inhaled
Causes skin irritation
Causes serious eye irritation
May cause allergy or asthma symptoms or breathing difficulties if inhaled
May cause an allergic skin reaction
Suspected of causing cancer
Suspected of damaging fertility or the unborn child
Causes damage to organs through prolonged or repeated exposure
_____________________________________________________________________________________________
100400_100407 – EVERCOAT POLYESTER GLAZING
PUTTY
Revision Date 21-Feb-2019
Precautionary Statements – Prevention
Obtain special instructions before use
Do not handle until all safety precautions have been read and understood
Use personal protective equipment as required
Use only outdoors or in a well-ventilated area
Wash face, hands and any exposed skin thoroughly after handling
In case of inadequate ventilation wear respiratory protection
Contaminated work clothing should not be allowed out of the workplace
Do not breathe dust/fume/gas/mist/vapors/spray
Do not eat, drink or smoke when using this product
Keep away from heat/sparks/open flames/hot surfaces. – No smoking
Keep container tightly closed
Ground/bond container and receiving equipment
Use explosion-proof electrical/ ventilating/ lighting/ equipment
Use non-sparking tools
Take precautionary measures against static discharge
Wear protective gloves/protective clothing/eye protection/face protection
Precautionary Statements – Response
IF exposed or concerned: Get medical advice/attention
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing
If eye irritation persists: Get medical advice/attention
If skin irritation or rash occurs: Get medical advice/attention
IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower
Wash contaminated clothing before reuse
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing
If experiencing respiratory symptoms: Call a POISON CENTER or doctor/physician
In case of fire: Use CO2, dry chemical, or foam to extinguish.
Precautionary Statements – Storage
Store locked up
Store in a well-ventilated place. Keep cool
Precautionary Statements – Disposal
Dispose of contents/container to an approved waste disposal plant
Hazards not otherwise classified (HNOC)
Not applicable
Other Information
Toxic to aquatic life with long lasting effects. Toxic to aquatic life.
3. COMPOSITION/INFORMATION ON INGREDIENTS
Flammable liquid and vapor
Appearance White Physical state Liquid Odor Aromatic
_____________________________________________________________________________________________
Page 2 / 9
_____________________________________________________________________________________________
100400_100407 – EVERCOAT POLYESTER GLAZING
PUTTY
Revision Date 21-Feb-2019
Chemical Name CAS No Weight-%
Talc (hydrous magnesium silicate) 14807-96-6 10 – 30
Magnesite 546-93-0 10 – 30
Styrene 100-42-5 10 – 30
Titanium Dioxide 13463-67-7 3 – 7
Trade Secret Proprietary 0.1 – 1
4. FIRST AID MEASURES
Description of first aid measures
General advice Get medical advice/attention if you feel unwell.
Eye contact IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if
present and easy to do. Continue rinsing. If eye irritation persists: Get medical
advice/attention.
Skin contact IF ON SKIN:. Wash skin with soap and water. If skin irritation persists, call a physician.
Take off contaminated clothing and wash before reuse.
Inhalation IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for
breathing. If symptoms persist, call a physician.
Ingestion IF SWALLOWED:. Do NOT induce vomiting. Never give anything by mouth to an
unconscious person. Call a physician.
Self-protection of the first aider Ensure that medical personnel are aware of the material(s) involved and take precautions to
protect themselves.
Most important symptoms and effects, both acute and delayed
Symptoms See section 2 for more information.
Indication of any immediate medical attention and special treatment needed
Note to physicians Treat symptomatically.
5. FIRE-FIGHTING MEASURES
Suitable extinguishing media
Carbon dioxide (CO2), Dry chemical, Foam
Unsuitable extinguishing media
None
Specific hazards arising from the chemical
Flammable.
Explosion data
Sensitivity to Mechanical Impact None.
Sensitivity to Static Discharge None.
Protective equipment and precautions for firefighters
As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full
protective gear.
6. ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures
_____________________________________________________________________________________________
Page 3 / 9
_____________________________________________________________________________________________
100400_100407 – EVERCOAT POLYESTER GLAZING
PUTTY
Revision Date 21-Feb-2019
Personal precautions Remove all sources of ignition. Use personal protective equipment as required.
Environmental precautions
Environmental precautions Do not flush into surface water or sanitary sewer system.
Methods and material for containment and cleaning up
Methods for containment Prevent further leakage or spillage if safe to do so.
Methods for cleaning up Soak up with inert absorbent material.
Prevention of secondary hazards Clean contaminated objects and areas thoroughly observing environmental regulations.
7. HANDLING AND STORAGE
Precautions for safe handling
Advice on safe handling Handle in accordance with good industrial hygiene and safety practice. Avoid breathing
vapors or mists. Avoid contact with skin, eyes or clothing. Wash thoroughly after handling.
Wash contaminated clothing before reuse. Use personal protective equipment as required.
Conditions for safe storage, including any incompatibilities
Storage Conditions Keep away from heat, sparks, flame and other sources of ignition (i.e., pilot lights, electric
motors and static electricity).
Incompatible materials Strong oxidizing agents
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Control parameters
Exposure Guidelines .
Chemical Name ACGIH TLV OSHA PEL NIOSH IDLH
Talc (hydrous magnesium silicate)
14807-96-6
TWA: 2 mg/m
3
particulate matter
containing no asbestos and <1%
crystalline silica, respirable
particulate matter
(vacated) TWA: 2 mg/m
3
respirable
dust <1% Crystalline silica,
containing no Asbestos
TWA: 20 mppcf if 1% Quartz or
more;use Quartz limit
IDLH: 1000 mg/m
3
TWA: 2 mg/m
3
containing no
Asbestos and <1% Quartz
respirable dust
Magnesite
546-93-0
- - TWA: 10 mg/m
3
total dust
TWA: 5 mg/m
3
respirable dust
Styrene
100-42-5
STEL: 40 ppm
TWA: 20 ppm
TWA: 100 ppm
(vacated) TWA: 50 ppm
(vacated) TWA: 215 mg/m
3
(vacated) STEL: 100 ppm
(vacated) STEL: 425 mg/m
3
Ceiling: 200 ppm
IDLH: 700 ppm
TWA: 50 ppm
TWA: 215 mg/m
3
STEL: 100 ppm
STEL: 425 mg/m
3
Titanium Dioxide
13463-67-7
TWA: 10 mg/m
3
TWA: 15 mg/m
3
total dust
(vacated) TWA: 10 mg/m
3
total
dust
IDLH: 5000 mg/m
3
TWA: 2.4 mg/m
3
CIB 63 fine
TWA: 0.3 mg/m
3
CIB 63 ultrafine,
including engineered nanoscale
NIOSH IDLH Immediately Dangerous to Life or Health
Other Information Vacated limits revoked by the Court of Appeals decision in AFL-CIO v. OSHA, 965 F.2d 962
(11th Cir., 1992).
Appropriate engineering controls
Engineering Controls Showers
Eyewash stations
Ventilation systems
_____________________________________________________________________________________________
Page 4 / 9
_____________________________________________________________________________________________
100400_100407 - EVERCOAT POLYESTER GLAZING
PUTTY
Revision Date 21-Feb-2019
Individual protection measures, such as personal protective equipment
Eye/face protection Wear safety glasses with side shields (or goggles).
Skin and body protection Wear protective natural rubber, nitrile rubber, Neoprene or PVC gloves.
Respiratory protection Use NIOSH-approved air-purifying respirator with organic vapor cartridge or canister, as
appropriate.
General Hygiene Considerations Handle in accordance with good industrial hygiene and safety practice. Regular cleaning of
equipment, work area and clothing is recommended.
9. PHYSICAL AND CHEMICAL PROPERTIES
9.1. Information on basic physical and chemical properties
Physical state Liquid
Appearance White
Odor Aromatic
Odor threshold No information available
Explosive properties No information available
Oxidizing properties No information available
Other Information
Softening point No information available
Molecular weight No information available
VOC Content (%) No information available
Applied 0.4 lbs/gal
Density No information available
Bulk density No information available
SADT (self-accelerating
decomposition temperature)
No information available
10. STABILITY AND REACTIVITY
Reactivity
Chemical stability
Property Values Remarks Method
pH No information available
Melting point / freezing point No information available
Boiling point / boiling range 145 C / 293 F
Flash point 34 C / 93 F
Evaporation rate No information available
Flammability (solid, gas) No information available
Flammability Limit in Air
Upper flammability limit: No information available
Lower flammability limit: No information available
Vapor pressure No information available
Vapor density No information available
Relative density 1.78
Water solubility No information available
Solubility(ies) No information available
Partition coefficient 1.36
Autoignition temperature No information available
Decomposition temperature No information available
Kinematic viscosity No information available
Dynamic viscosity No information available
No information available
_____________________________________________________________________________________________
Page 5 / 9
_____________________________________________________________________________________________
100400_100407 - EVERCOAT POLYESTER GLAZING
PUTTY
Revision Date 21-Feb-2019
Stable under normal conditions
Possibility of Hazardous Reactions
None under normal processing.
Conditions to avoid
Excessive heat.
Incompatible materials
Strong oxidizing agents
Hazardous Decomposition Products
Carbon oxides
11. TOXICOLOGICAL INFORMATION
Information on likely routes of exposure
Inhalation May cause irritation of respiratory tract.
Eye contact Contact with eyes may cause irritation. May cause redness and tearing of the eyes.
Skin contact May cause skin irritation and/or dermatitis.
Ingestion Ingestion may cause irritation to mucous membranes.
Chemical Name Oral LD50 Dermal LD50 Inhalation LC50
Styrene
100-42-5
= 1000 mg/kg ( Rat ) > 2000 mg/kg ( Rat ) = 11.7 mg/L ( Rat ) 4 h
Titanium Dioxide
13463-67-7
> 10000 mg/kg ( Rat ) – –
Trade Secret
= 5410 mg/kg ( Rat ) – –
Information on toxicological effects
Symptoms No information available.
Delayed and immediate effects as well as chronic effects from short and long-term exposure
Sensitization No information available.
Germ cell mutagenicity No information available.
Carcinogenicity The table below indicates whether each agency has listed any ingredient as a carcinogen.
Chemical Name ACGIH IARC NTP OSHA
Talc (hydrous magnesium
silicate)
14807-96-6
– Group 3 – X
Styrene
100-42-5
– Group 2A Reasonably Anticipated X
Titanium Dioxide
13463-67-7
– Group 2B – X
IARC (International Agency for Research on Cancer)
Group 2B – Possibly Carcinogenic to Humans
Not classifiable as a human carcinogen
NTP (National Toxicology Program)
Reasonably Anticipated – Reasonably Anticipated to be a Human Carcinogen
OSHA (Occupational Safety and Health Administration of the US Department of Labor)
X – Present
Chronic toxicity May cause adverse liver effects. Contains a known or suspected reproductive toxin.
Target Organ Effects Central nervous system, Central Vascular System (CVS), Eyes, Liver, Lungs, Reproductive
System, Respiratory system, Skin.
_____________________________________________________________________________________________
Page 6 / 9
The following values are calculated based on chapter 3.1 of the GHS document .
_____________________________________________________________________________________________
100400_100407 – EVERCOAT POLYESTER GLAZING
PUTTY
Revision Date 21-Feb-2019
ATEmix (inhalation-dust/mist) 2.2 mg/l
12. ECOLOGICAL INFORMATION
Ecotoxicity
48.5642 % of the mixture consists of component(s) of unknown hazards to the aquatic environment
Persistence and degradability
No information available.
Bioaccumulation
No information available.
Mobility
No information available.
Chemical Name Partition coefficient
Styrene
100-42-5
2.95
Other adverse effects
No information available
13. DISPOSAL CONSIDERATIONS
Waste treatment methods
Disposal of wastes This material, as supplied, is a hazardous waste according to federal regulations (40 CFR
261).
Contaminated packaging Do not reuse container.
US EPA Waste Number D001
This product contains one or more substances that are listed with the State of California as a hazardous waste.
Chemical Name California Hazardous Waste Status
Styrene
100-42-5
Toxic
Ignitable
14. TRANSPORT INFORMATION
Note: This information is not intended to convey all specific regulatory information relating to this product.
Transportation classifications may vary by container volume and may be influenced by regional or
country variations in regulations. It is the responsibility of the transporting organization to follow all
applicable laws, regulations and rules relating to the transportation of the material.
DOT
UN/ID No UN3269
Proper shipping name: Polyester Resin Kit
Hazard Class 3
Packing Group III
IATA
UN/ID No UN3269
Proper shipping name: Polyester Resin Kit
Hazard Class 3
Packing Group III
_____________________________________________________________________________________________
Page 7 / 9
_____________________________________________________________________________________________
100400_100407 – EVERCOAT POLYESTER GLAZING
PUTTY
Revision Date 21-Feb-2019
ERG Code No information available.
IMDG
UN/ID No UN3269
Proper shipping name: Polyester Resin Kit
Hazard Class 3
Packing Group III
EmS-No No information available
15. REGULATORY INFORMATION
International Inventories
TSCA Complies
DSL/NDSL Complies
EINECS/ELINCS Complies
ENCS Complies
IECSC Complies
KECL Complies
PICCS Not determined
AICS Complies
Legend:
TSCA – United States Toxic Substances Control Act Section 8(b) Inventory
DSL/NDSL – Canadian Domestic Substances List/Non-Domestic Substances List
EINECS/ELINCS – European Inventory of Existing Chemical Substances/European List of Notified Chemical Substances
ENCS – Japan Existing and New Chemical Substances
IECSC – China Inventory of Existing Chemical Substances
KECL – Korean Existing and Evaluated Chemical Substances
PICCS – Philippines Inventory of Chemicals and Chemical Substances
AICS – Australian Inventory of Chemical Substances
US Federal Regulations
SARA 313
Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA). This product contains a chemical
or chemicals which are subject to the reporting requirements of the Act and Title 40 of the Code of Federal Regulations, Part 372
Chemical Name SARA 313 – Threshold Values %
Styrene – 100-42-5 0.1
SARA 311/312 Hazard Categories
Acute health hazard No
Chronic Health Hazard No
Fire hazard Yes
Sudden release of pressure hazard No
Reactive Hazard No
CWA (Clean Water Act)
This product contains the following substances which are regulated pollutants pursuant to the Clean Water Act (40 CFR 122.21
and 40 CFR 122.42)
Chemical Name CWA – Reportable
Quantities
CWA – Toxic Pollutants CWA – Priority Pollutants CWA – Hazardous
Substances
Styrene
100-42-5
1000 lb – – X
CERCLA
This material, as supplied, contains one or more substances regulated as a hazardous substance under the Comprehensive
Environmental Response Compensation and Liability Act (CERCLA) (40 CFR 302)
Chemical Name Hazardous Substances RQs CERCLA/SARA RQ Reportable Quantity (RQ)
Styrene
100-42-5
1000 lb – RQ 1000 lb final RQ
RQ 454 kg final RQ
_____________________________________________________________________________________________
Page 8 / 9
_____________________________________________________________________________________________
100400_100407 – EVERCOAT POLYESTER GLAZING
PUTTY
Revision Date 21-Feb-2019
US State Regulations
California Proposition 65
This product contains the following Proposition 65 chemicals
Chemical Name California Proposition 65
Styrene – 100-42-5 Carcinogen
Titanium Dioxide – 13463-67-7 Carcinogen
U.S. State Right-to-Know Regulations
Chemical Name New Jersey Massachusetts Pennsylvania
Talc (hydrous magnesium silicate)
14807-96-6
X X X
Styrene
100-42-5
X X X
Titanium Dioxide
13463-67-7
X X X
Tetrahydrophthalic Anhydride
85-43-8
X – –
U.S. EPA Label Information
EPA Pesticide Registration Number Not applicable
WHMIS Hazard Class
D2A – Very toxic materials, B2 – Flammable liquid
16. OTHER INFORMATION, INCLUDING DATE OF PREPARATION OF THE LAST REVISION
NFPA (National Fire Protection Association)
HMIS (Hazardous Material Information System)
Revision Date 21-Feb-2019
Disclaimer
Illinois Tool Works Inc. believes the information contained in this data sheet is accurate as of the date compiled.
However, Illinois Tool Works Inc. makes no warranty, express or implied, as to the accuracy, reliability or completeness
of the information. User is responsible for evaluating whether such information or this product is fit for a particular
purpose and suitable for a particular use or application. The information in this data sheet may not be valid if this
product is used in combination with other products or in processes for which it was not designed. Illinois Tool Works Inc.
disclaims any liability for consequential or incidental damages of any kind, including lost profits, arising from the sale or
use of this product. Ensure you have the most current version of this data sheet by contacting us or reviewing our web
site.
End of Safety Data Sheet
NFPA Health hazards 2 Flammability 3 Instability 0 –
HMIS Health hazards 2 Flammability 3 Physical hazards 0 Personal protection B
_____________________________________________________________________________________________
Page 9 / 9