MATERIAL SAFETY DATA SHEET
FORMULA FIVE
Mold Cleaner
MSDS Number: F5C-001 Effective Date: 01 March 2007 Page 1 of 6
SECTION
1: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME FORMULA FIVE
Mold Cleaner
GENERIC NAME Mold Cleaner
MANUFACTURER REXCO
P.O. Box 80996
Conyers, Georgia 30013
USA
TRANSPORTATION EMERGENCY :
CHEMTREC (800) 424-9300 U.S.A. (24 hours/day)
CHEMTREC (703) 527-3887 International (Collect calls accepted)
CUSTOMER SERVICE AND PRODUCT EMERGENCY :
REXCO (800) 888-1060 U.S.A and Canada
REXCO (770) 483-7610 International
SECTION 2: COMPOSITION / INFORMATION ON INGREDIENTS
COMPONENT CAS NUMBER CONCENTRATION (%)
Toluene* 108-88-3 28 – 32%
Xylene* 1330-20-7 28 – 32%
Ethyl Methyl Ketone* 78-93-3 37 – 43%
*This chemical is subject to the reporting requirements of section 313 of SARA Title III.
SECTION
3: HAZARDS IDENTIFICATION
NFPA RATING: Health 2, Fire 3, Reactivity 1
HMIS RATING: Health 2, Fire 3, Reactivity 1
0=
MINIMAL, 1=SLIGHT, 2=MODERATE, 3=HIGH, 4=EXTREME
POTENTIAL HEALTH EFFECTS
EYES Irritating to eyes, ranging from temporary irritation, transient corneal injury and pain to
possible permanent injury or blindness.
SKIN Irritating to skin. Prolonged or repeated exposure may result in de-fatting, skin dermatitis,
reddening, blisters or temporary loss of feeling depending on exposure.
INHALATION Harmful. Danger of serious damage to health by prolonged inhalation. Vapors may cause
nausea, vomiting, gastrointestinal bleeding, abdominal pain, and central nervous system
depression with symptoms ranging from drunkenness to unconsciousness, narcosis, coma,
cyanosis, respiratory failure, and death, depending on the quantity ingested.
MATERIAL SAFETY DATA SHEET
FORMULA FIVE
Mold Cleaner
MSDS Number: F5C-001 Effective Date: 01 March 2007 Page 2 of 6
INGESTION Harmful. May cause lung damage if swallowed. May cause nausea, vomiting, gastrointestinal
bleeding, abdominal pain, and central nervous system depression with symptoms ranging
from drunkenness to unconsciousness, narcosis, coma, respiratory failure, mild to severe
pulmonary injury, and death, depending on the quantity ingested.
CHRONIC HEALTH EFFECTS : May result in harm to unborn child.
SYMPTOMS OF EXPOSURE : Symptoms of exposure through inhalation, ingestion, or direct contact with skin
may include nausea, vomiting, diarrhea, irritation of nose, throat, airways, or skin, central nervous system
depression possibly including headache, loss of coordination, drowsiness, fatigue, and unconsciousness
and death in extreme cases. Pre-existing eye, skin, or respiratory disorders may be aggravated by exposure
to this product.
PRIMARY ROUTES OF ENTRY : Skin contact, skin absorption, eye contact, and inhalation
CANCER INFORMATION : Neither this product nor any of its components is listed as a carcinogen or partial
carcinogen by the following agencies: the National Toxicology Program, the International Agency for
Research on Cancer, and the Occupational Safety and Health Administration.
SECTION 4: FIRST AID MEASURES
EYES Flush immediately with cold water for 15 minutes and seek medical attention.
SKIN Remove contaminated clothing and wash affected area with soap and water. If irritation from
contact persists, seek medical attention. Launder contaminated clothing including shoes
prior to reuse.
INHALATON If light-headed or having difficulty breathing, expose individual to fresh air and/or oxygen. If
breathing stops, begin artificial respiration and seek immediate medical attention.
INGESTION Seek immediate medical attention. Only induce vomiting if directed to do so by medical
personnel. If vomiting occurs spontaneously, keep victim s head below hips to prevent
aspiration into lungs. If possible, do not leave victim unattended.
SECTION 5: FIRE FIGHTING MEASURES
FLASH POINT / METHOD: <73 F (23 C) / Tagliabue Closed Cup method (TCC)
AUTO IGNITION TEMPERATURE : Not Applicable
FLAMMABLE LIMITS IN AIR (% BY VOLUME): LEL Lower 1.2% / UEL Upper 7%
FIRE AND EXPLOSION HAZARDS : Flammable. Low flash point. Keep work areas free of hot metal surfaces
and other sources of ignition.
EXTINGUISHING MEDIA: Use dry chemicals, CO2, water fog, or foam.
FIRE FIGHTING INSTRUCTIONS: Wear a NIOSH-approved self contained breathing apparatus in positive
pressure mode and full bunker gear. Water may be unsuitable as an extinguishing media but helpful in
keeping adjacent containers cool in order to prevent container rupture. Avoid spreading burning liquid with
water used for cooling purposes.
MATERIAL SAFETY DATA SHEET
FORMULA FIVE
Mold Cleaner
MSDS Number: F5C-001 Effective Date: 01 March 2007 Page 3 of 6
SECTION 6: ACCIDENTAL RELEASE MEASURES
IN CASE OF SPILL: Keep sources of ignition and hot metal surfaces isolated from spill. Persons involved in
clean-up should wear personal protection equipment. Stop spill at source and prevent from spreading. Flush
spilled material into suitable retaining areas or containers. Small amounts of spilled material may be absorbed
with any standard absorbent. If run-off occurs, notify proper authorities as required. Place in chemical waste
container and dispose of in accordance with local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
Store in a dry location at 60 - 80 F (15 - 27 C) and away from open flames, heat, and sparks. Do not store at
temperatures above 110 F (43 C) to avoid vapor pressure in closed containers. Store only in areas
approved for Flammable Liquid. Keep work areas free of hot metal surfaces and other sources of ignition.
Keep container tightly closed when not in use.
Repacking not recommended. Repack only into high-density polyethylene (HDPE) or steel containers. Do not
repack in aluminum containers. Containers used for repackaging should be thoroughly tested for long-term
product compatibility before use. Ground all equipment before pumping the product. Protect from static
electrical sparks or other ignition sources. All new containers must exhibit product labels required for proper
identification, safety, handling, and storage. Store away from strong oxidizers. Empty containers may contain
product residue such as vapors continue to observe proper handling and storage precautions.
SECTION 8: EXPOSURE CONTROLS / PERSONAL PROTECTION
EYE PROTECTION: Safety glasses with side shields, chemical goggles, or face shield are advised. Eye
washes are recommended for work areas.
SKIN PROTECTON: Wear impervious gloves (neoprene, rubber, NBR nitrile), clothing, and shoes to prevent
skin contact. Safety showers are recommended for work areas. Remove contaminated clothing and wash in
hot water and soap prior to reuse.
RESPIRATORY PROTECTION : Exposure levels should be kept below the PEL or TLV for this product. Local
exhaust preferred. If exposure exceeds recommended levels, use of NIOSH-approved cartridge respirator or
gas mask is advised. Engineering controls should be implemented if necessary to reduce exposure.
ENGINEERING CONTROLS : Provide sufficient general and/or local exhaust (explosion-proof ventilation) to
keep exposure below PEL or TLV.
EXPOSURE GUIDELINES
COMPONENT OSHA TWA ACGIH TLV
Toluene 200 ppm PEL/TWA 50 ppm TLV/TWA
Xylene 100 ppm PEL/TWA 100 ppm TLV/TWA
Ethyl Methyl Ketone 200 ppm PEL/TWA 200 ppm TLV/TWA
PEL = PERMISSIBLE EXPOSURE LIMITS TLV = THRESHOLD LIMIT VALUE TWA = TIME WEIGHTED AVERAGE (8 HOURS)
MATERIAL SAFETY DATA SHEET
FORMULA FIVE
Mold Cleaner
MSDS Number: F5C-001 Effective Date: 01 March 2007 Page 4 of 6
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE: Clear Liquid SPECIFIC GRAVITY (H2O=1): 0.84
ODOR: Mild Solvent EVAPORATION RATE (BUTYL ACETATE= 1) : <1
BOILING POINT: 176 286 F (80 141 C) VAPOR DENSITY (AIR= 1) : > AIR
MELTING POINT: Not Applicable SOLUBILITY IN WATER: Insoluble
V.O.C. 0.826 g/cm
3
REACTIVITY IN WATER: No
V.O.C. = VOLATILE ORGANIC CONTENT
SECTION 10: STABILITY AND REACTIVITY
STABILITY: Stable
CONDITIONS TO AVOID: Open flames, hot surfaces, or any ignition source.
INCOMPATIBILITY: Incompatible with strong oxidizing agents, strong acids or bases, alkali metals, halogens,
and strong alkalis.
HAZARDOUS DECOMPOSITION : Thermal decomposition in the presence of air may yield carbon monoxide
and/or carbon dioxide, toxic gases. Smoke and vapor.
HAZARDOUS POLYMERIZATION : Will not occur
SECTION 11: TOXICOLOGICAL INFORMATION
EYES: May cause mild and temporary irritation of eyes and mucous membranes to permanent injury
or blindness.
SKIN: May cause irritation to skin through drying and de-fatting. May cause reddening, dermatitis,
skin cracking, eczema, blisters or temporary loss of feeling.
INHALATION: Vapor at low concentrations may cause mild irritation of respiratory system or lungs. At high
concentrations and exposure may cause nausea, vomiting, headaches, unconsciousness,
cyanosis or death.
INGESTION: May cause irritation of mucous membranes or abdominal pain. Severe exposure may cause
pulmonary injury possibly death.
SECTION 12: ECOLOGICAL INFORMATION
Not soluble in water.
MATERIAL SAFETY DATA SHEET
FORMULA FIVE
Mold Cleaner
MSDS Number: F5C-001 Effective Date: 01 March 2007 Page 5 of 6
SECTION 13: DISPOSAL CONSIDERATIONS
Waste material may be incinerated at an approved facility where permitted under appropriate Federal, State,
and Local regulations.
SECTION 14: TRANSPORT INFORMATION
DOT CLASSIFICATION: Flammable Liquid, n.o.s. (Methyl Ethyl Ketone, Toluene); 3; UN1993;
Packing Group II
ICAO / IATA CLASSIFICATION: UN1993; Flammable Liquid, n.o.s. (Methyl Ethyl Ketone, Toluene); 3;
Packing Group II
IMDG CLASSIFICATION: UN1993; Flammable Liquid, n.o.s. (Methyl Ethyl Ketone, Toluene); 3;
Packing Group II
SECTION 15: REGULATORY INFORMATION
COMPREHENSIVE ENVIRONMENTAL RESPONSE COMPENSATION AND LIABILITY ACT OF 1980 (CERCLA)
COMPONENT
REPORTABLE QUANTITY (RQ)
Toluene 1000 lbs Xylene 1000 lbs
Ethyl Methyl Ketone 5000 lbs
SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT OF 1986 (SARA) TITLE III
SARA 302
: Extremely Hazardous Substance: NO
SARA 311: Hazardous Chemical: YES
HAZARD CATEGORIES: FIRE YES
REACTIVITY NO
SUDDEN RELEASE OF PRESSURE NO
IMMEDIATE RELEASE OF PRESSURE YES
DELAYED RELEASE OF PRESSURE YES
OCCUPATIONAL HEALTH AND SAFETY ADMINISTRATION (OSHA) CLASSIFICATION: 29 CFR 1910.1200
Hazardous Chemical: YES
CALIFORNIA PROPOSITION 65: WARNING -This product contains a chemical(s) known to the state of
California to cause birth defects or other reproductive harm.
WORKPLACE HAZARDOUS MATERIAL INFORMATION SYSTEM (WHMIS) CLASSIFICATION:
Hazardous: Flammable Liquid
MATERIAL SAFETY DATA SHEET
FORMULA FIVE
Mold Cleaner
MSDS Number: F5C-001 Effective Date: 01 March 2007 Page 6 of 6
CHEMICAL INVENTORY: Components are either listed on the following chemical inventories or qualify for an
exemption:
UNITED STATES Toxic Substances Control Act (TSCA)
CANADA Canadian Domestic Substance List (DSL)
EUROPE European Inventory of Existing Commer cial Chemical Substances (EINECS)
AUSTRALIA Australian Inventory of Chemical Substances (AICS)
JAPAN Existing and New Chemical Substances (MITI)
S. KOREA Existing Chemicals List (KECL)
SECTION 16: OTHER INFORMATION
All information provided in this Material Safety Data Sheet is believed to be accurate and reliable of typical
values and not as a product specification. REXCO makes no warranty of any kind, express or implied,
including warranties of merchantability or fitness for a particular purpose, concerning the safe use of this
material in your process or in combination with other substances. Users should make their own tests and
assessments as to the suitability of this product or the information contained herein for their particular
purposes and uses and compliance with all applicable laws and regulations.
Prepared by: REXCO Product Stewardship Department