Duroct Cobalt 12%
Safety data sheet
according to 29 CFR 1910.1200
SECTION 1: IDENTIFICATION
1.1GHS Product identifier:Duroct Cobalt 12%
1.2Recommended use of the chemical and restrictions on use:
Relevant uses: Catalyst for coatings. For industrial user only.
Uses advised against: All uses not specified in this section or in section 7.3
1.3Name, address, and telephone number of the chemical manufacturer, importer, or other responsible party:
DURA CHEMICALS, INC.
2200 Powell Street, Suite 450
94608 Emeryville – California – U.S.A.
Phone.: 1-510-658-1987 – Fax: 1-510-658-8025
www.durachem.com
1.4Emergency phone number: 1-800-424-9300 CHEMTREC
SECTION 2: HAZARD(S) IDENTIFICATION
2.1Classification of the substance or mixture:
NFPA:
Health Hazards: 2
Flammability Hazards: 2
Instability Hazards: 0
Special Hazards: Non-applicable
29 CFR 1910.1200:
Classification of this product has been carried out in accordance with paragraph (d) of 1910.1200.
Eye Irrit. 2: Eye irritation, Category 2, H319
Flam. Liq. 4: Flammable liquids, Category 4, H227
Repr. 1B: Reproductive toxicity, Category 1B, H360
Skin Sens. 1A: Sensitisation, skin, Category 1A, H317
2.2Label elements:
NFPA:
29 CFR 1910.1200:
Danger
Hazard statements:
Eye Irrit. 2: H319 – Causes serious eye irritation
Flam. Liq. 4: H227 – Combustible liquid
Repr. 1B: H360 – May damage fertility or the unborn child
Skin Sens. 1A: H317 – May cause an allergic skin reaction
Precautionary statements:
P201: Obtain special instructions before use
P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking
P280: Wear protective gloves/protective clothing/eye protection/face protection
P302+P352: IF ON SKIN: Wash with plenty of soap and water
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing
P308+P313: IF exposed or concerned: Get medical advice/attention
P370+P378: In case of fire: Use ABC powder extinguisher to put it out
P501: Dispose of contents and / or containers in accordance with regulations on hazardous waste or packaging and packaging
waste respectively
Substances that contribute to the classification
Page 1/10Date of compilation: 7/2/2018 Revised: 1/16/2020 Version: 5 (Replaced 4)
– CONTINUED ON NEXT PAGE –
Duroct Cobalt 12%
Safety data sheet
according to 29 CFR 1910.1200
SECTION 2: HAZARD(S) IDENTIFICATION (continued)
Cobalt bis(2-ethylhexanoate) (CAS: 136-52-7)
2.3Hazards not otherwise classified (HNOC):
Non-applicable
SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS
3.1Substances:
Non-applicable
3.2Mixtures:
Chemical description:Additive/s
Components:
Remaining components are non-hazardous and/or present at amounts below reportable limits. The specific chemical identity
and/or exact percentage (concentration) of composition has been withheld as a trade secret in accordance with paragraph (i) of
1910.1200.Therefore, in accordance with Appendix D to 1910.1200, the product contains:
Identification Chemical name Concentration
CAS:136-52-7 Cobalt bis(2-ethylhexanoate) 60 – <75 %
CAS:64742-47-8 Distillates (petroleum), hydrotreated light (60 C < fp < 93 C) 25 - <40 %
To obtain more information on the hazards of the substances consult sections 11, 12 and 16.
SECTION 4: FIRST-AID MEASURES
4.1Description of necessary measures:
The symptoms resulting from intoxication can appear after exposure, therefore, in case of doubt, seek medical attention for
direct exposure to the chemical product or persistent discomfort, showing the SDS of this product.
By inhalation:
This product does not contain substances classified as hazardous for inhalation, however, in case of symptoms of intoxication
remove the person affected from the exposure area and provide with fresh air. Seek medical attention if the symptoms get worse
or persist.
By skin contact:
Remove contaminated clothing and footwear, rinse skin or shower the person affected if appropriate with plenty of cold water
and neutral soap. In serious cases see a doctor. If the product causes burns or freezing, clothing should not be removed as this
could worsen the injury caused if it is stuck to the skin. If blisters form on the skin, these should never be burst as this will
increase the risk of infection.
By eye contact:
Rinse eyes thoroughly with lukewarm water for at least 15 minutes. Do not allow the person affected to rub or close their eyes.
If the injured person uses contact lenses, these should be removed unless they are stuck to the eyes, as this could cause further
damage. In all cases, after cleaning, a doctor should be consulted as quickly as possible with the SDS of the product.
By ingestion/aspiration:
Do not induce vomiting, but if it does happen keep the head down to avoid aspiration. Keep the person affected at rest. Rinse
out the mouth and throat, as they may have been affected during ingestion.
4.2Most important symptoms/effects, acute and delayed:
Acute and delayed effects are indicated in sections 2 and 11.
4.3Indication of immediate medical attention and special treatment needed, if necessary:
Non-applicable
SECTION 5: FIRE-FIGHTING MEASURES
5.1Suitable (and unsuitable) extinguishing media:
Page 2/10Date of compilation: 7/2/2018 Revised: 1/16/2020 Version: 5 (Replaced 4)
- CONTINUED ON NEXT PAGE -
Duroct Cobalt 12%
Safety data sheet
according to 29 CFR 1910.1200
SECTION 5: FIRE-FIGHTING MEASURES (continued)
Combustible liquid. In the case of inflammation as a result of improper manipulation, storage or use preferably use polyvalent
powder extinguishers (ABC powder), in accordance with the Regulation on fire protection systems. IT IS NOT RECOMMENDED to
use full jet water as an extinguishing agent.
5.2Specific hazards arising from the chemical:
As a result of combustion or thermal decomposition reactive sub-products are created that can become highly toxic and,
consequently, can present a serious health risk.
5.3Special protective equipment and precautions for fire-fighters:
Depending on the magnitude of the fire it may be necessary to use full protective clothing and individual respiratory equipment.
Minimum emergency facilities and equipment should be available (fire blankets, portable first aid kit,...)
Additional provisions:
As in any fire, prevent human exposure to fire, smoke, fumes or products of combustion. Only properly trained personnel should
be involved in firefighting. Evacuate nonessential personnel from the fire area. Destroy any source of ignition. In case of fire,
refrigerate the storage containers and tanks for products susceptible to inflammation. Avoid spillage of the products used to
extinguish the fire into an aqueous medium.
SECTION 6: ACCIDENTAL RELEASE MEASURES
6.1Personal precautions, protective equipment and emergency procedures:
Isolate leaks provided that there is no additional risk for the people performing this task. Personal protection equipment must be
used against potential contact with the spilt product (See section 8). Evacuate the area and keep out those who do not have
protection.
6.2Environmental precautions:
This product is not classified as hazardous to the environment. Keep product away from drains, surface and underground water.
6.3Methods and materials for containment and cleaning up:
It is recommended:
Absorb the spillage using sand or inert absorbent and move it to a safe place. Do not absorb in sawdust or other combustible
absorbents. For any concern related to disposal consult section 13.
6.4Reference to other sections:
See sections 8 and 13.
SECTION 7: HANDLING AND STORAGE
7.1Precautions for safe handling:
A.-Precautions for safe manipulation
Comply with the current standards 29 CFR 1910 Occupational Safety and Health Standards. Keep containers hermetically
sealed. Control spills and residues, destroying them with safe methods (section 6). Avoid leakages from the container.
Maintain order and cleanliness where dangerous products are used.
B.-Technical recommendations for the prevention of fires and explosions
Product is non-flammable under normal conditions of storage, manipulation and use. It is recommended to transfer at slow
speeds to avoid the generation of electrostatic charges that can affect flammable products. Consult section 10 for information
on conditions and materials that should be avoided.
C.-Technical recommendations to prevent ergonomic and toxicological risks
PREGNANT WOMEN SHOULD NOT BE EXPOSED TO THIS PRODUCT. Transfer in fixed places that comply with the necessary
security conditions (emergency showers and eyewash stations in close proximity), using personal protection equipment,
especially on the hands and face (See section 8). Limit manual transfers to containers of small amounts. Do not eat or drink
during the process, washing hands afterwards with suitable cleaning products.
D.-Technical recommendations to prevent environmental risks
It is recommended to have absorbent material available at close proximity to the product (See subsection 6.3)
7.2Conditions for safe storage, including any incompatibilities:
A.-Technical measures for storage
Minimum Temp.: 41 F
Maximum Temp.: 86 F
Maximum time: 60 Months
Page 3/10Date of compilation: 7/2/2018 Revised: 1/16/2020 Version: 5 (Replaced 4)
- CONTINUED ON NEXT PAGE -
Duroct Cobalt 12%
Safety data sheet
according to 29 CFR 1910.1200
SECTION 7: HANDLING AND STORAGE (continued)
B.-General conditions for storage
Avoid sources of heat, radiation, static electricity and contact with food. For additional information see subsection 10.5
7.3Specific end use(s):
Except for the instructions already specified it is not necessary to provide any special recommendation regarding the uses of this
product.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1Control parameters:
Substances whose occupational exposure limits have to be monitored in the workplace
There are no occupational exposure limits for the substances contained in the product
8.2Appropriate engineering controls:
A.-Individual protection measures, such as personal protective equipment
As a preventative measure it is recommended to use basic Personal Protection Equipment. For more information on Personal
Protection Equipment (storage, use, cleaning, maintenance, class of protection, ) consult the information leaflet provided by
the manufacturer. For more information see subsection 7.1. All information contained herein is a recommendation, the
information on clothing performance must be combined with professional judgment, and a clear understanding of the clothing
application, to provide the best protection to the worker. All chemical protective clothing use must be based on a hazard
assessment to determine the risks for exposure to chemicals and other hazards. Conduct hazard assessments in accordance
with 29 CFR 1910.132.
B.-Respiratory protection
Pictogram PPE Remarks
Mandatory
respiratory tract
protection
Filter mask for gases and vapours
Replace when there is a taste or smell of the contaminant inside the face mask. If
the contaminant comes with warnings it is recommended to use isolation
equipment. Use respirator in accordance with manufacturer s use limitations and
OSHA standard 1910.134 (29CFR)
C.-Specific protection for the hands
Pictogram PPE Remarks
Mandatory hand
protection
NON-disposable chemical protective gloves
The Breakthrough Time indicated by the manufacturer must exceed the period
during which the product is being used. Do not use protective creams after the
product has come into contact with skin. Use gloves in accordance with
manufacturer s use limitations and OSHA standard 1910.138 (29CFR)
As the product is a mixture of several substances, the resistance of the glove material can not be calculated in advance with
total reliability and has therefore to be checked prior to the application
D.-Ocular and facial protection
Pictogram PPE Remarks
Mandatory face
protection
Face shield
Clean daily and disinfect periodically according to the manufacturer s instructions.
Use if there is a risk of splashing. Use this PPE in accordance with manufacturer s
use limitations and OSHA standard 1910.133 (29CFR)
E.-Bodily protection
Pictogram PPE Remarks
Mandatory complete
body protection
Disposable clothing for protection against
chemical risks
For professional use only. Clean periodically according to the manufacturer s
instructions.
Mandatory foot
protection
Safety footwear for protection against chemical
risk
Replace boots at any sign of deterioration. Use foot protection in accordance with
manufacturer s use limitations and OSHA standard 1910.136 (29CFR)
Page 4/10Date of compilation: 7/2/2018 Revised: 1/16/2020 Version: 5 (Replaced 4)
- CONTINUED ON NEXT PAGE -
Duroct Cobalt 12%
Safety data sheet
according to 29 CFR 1910.1200
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION (continued)
F.-Additional emergency measures
Emergency measure Standards Emergency measure Standards
Emergency shower
ANSI Z358-1
ISO 3864-1:2011, ISO 3864-4:2011
Eyewash stations
DIN 12 899
ISO 3864-1:2011, ISO 3864-4:2011
Environmental exposure controls:
In accordance with the community legislation for the protection of the environment it is recommended to avoid environmental
spillage of both the product and its container. For additional information see subsection 7.1.D
National volatile organic compound emission standards (40 CFR Part 59):
V.O.C. (Subpart C - Consumer):36.2 % weight
V.O.C. (Coatings) at 77 F: 372.86 kg/m (372.86 g/L)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
9.1Information on basic physical and chemical properties:
For complete information see the product datasheet.
Appearance:
Physical state at 68 F: Liquid
Appearance: Not available
Color: Cobalt
Odor: Not available
Odour threshold: Non-applicable *
Volatility:
Boiling point at atmospheric pressure: 429 F
Vapour pressure at 77 F: 939 Pa
Vapour pressure at 122 F: 3667.58 Pa (3.67 kPa)
Evaporation rate at 77 F: Non-applicable *
Product description:
Density at 77 F: 980 - 1080 kg/m
Relative density at 77 F: 1.03
Dynamic viscosity at 77 F: 250 cP
Kinematic viscosity at 77 F: 243 cSt
Kinematic viscosity at 104 F: Non-applicable *
Concentration: Non-applicable *
pH: Non-applicable *
Vapour density at 77 F: Non-applicable *
Partition coefficient n-octanol/water 77 F: Non-applicable *
Solubility in water at 77 F: Non-applicable *
Solubility properties: Non-applicable *
Decomposition temperature: Non-applicable *
Melting point/freezing point: Non-applicable *
Explosive properties: Non-applicable *
Oxidising properties: Non-applicable *
Flammability:
Flash Point: 149 F
*Not relevant due to the nature of the product, not providing information property of its hazards.
Page 5/10Date of compilation: 7/2/2018 Revised: 1/16/2020 Version: 5 (Replaced 4)
- CONTINUED ON NEXT PAGE -
Duroct Cobalt 12%
Safety data sheet
according to 29 CFR 1910.1200
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES (continued)
Flammability (solid, gas): Non-applicable *
Autoignition temperature: 437 F
Lower flammability limit: Non-applicable *
Upper flammability limit: Non-applicable *
Explosive:
Lower explosive limit: Non-applicable *
Upper explosive limit: Non-applicable *
9.2Other information:
Surface tension at 77 F: Non-applicable *
Refraction index: Non-applicable *
*Not relevant due to the nature of the product, not providing information property of its hazards.
SECTION 10: STABILITY AND REACTIVITY
10.1Reactivity:
No hazardous reactions are expected because the product is stable under recommended storage conditions. See section 7.
10.2Chemical stability:
Chemically stable under the conditions of storage, handling and use.
10.3Possibility of hazardous reactions:
Under the specified conditions, hazardous reactions that lead to excessive temperatures or pressure are not expected.
10.4Conditions to avoid:
Applicable for handling and storage at room temperature:
Shock and friction Contact with air Increase in temperature Sunlight Humidity
Not applicable Not applicable Risk of combustion Avoid direct impact Not applicable
10.5Incompatible materials:
Acids Water Oxidising materials Combustible materials Others
Avoid strong acids Not applicable Not applicable Not applicable Avoid alkalis or strong bases
10.6Hazardous decomposition products:
See subsection 10.3, 10.4 and 10.5 to find out the specific decomposition products. Depending on the decomposition conditions,
complex mixtures of chemical substances can be released: carbon dioxide (CO2), carbon monoxide and other organic
compounds.
SECTION 11: TOXICOLOGICAL INFORMATION
11.1Information on toxicological effects:
The experimental information related to the toxicological properties of the product itself is not available
Dangerous health implications:
In case of exposure that is repetitive, prolonged or at concentrations higher than recommended by the occupational exposure
limits, it may result in adverse effects on health depending on the means of exposure:
A-Ingestion (acute effect):
- Acute toxicity : Based on available data, the classification criteria are not met, as it does not contain substances classified
as dangerous for consumption. For more information see section 3.
- Corrosivity/Irritability: Based on available data, the classification criteria are not met, as it does not contain substances
classified as dangerous for this effect. For more information see section 3.
B-Inhalation (acute effect):
- Acute toxicity : Based on available data, the classification criteria are not met, as it does not contain substances classified
as dangerous for inhalation. For more information see section 3.
- Corrosivity/Irritability: Based on available data, the classification criteria are not met, as it does not contain substances
classified as dangerous for this effect. For more information see section 3.
Page 6/10Date of compilation: 7/2/2018 Revised: 1/16/2020 Version: 5 (Replaced 4)
- CONTINUED ON NEXT PAGE -
Duroct Cobalt 12%
Safety data sheet
according to 29 CFR 1910.1200
SECTION 11: TOXICOLOGICAL INFORMATION (continued)
C-Contact with the skin and the eyes (acute effect):
- Contact with the skin: Based on available data, the classification criteria are not met, as it does not contain substances
classified as dangerous for skin contact. For more information see section 3.
- Contact with the eyes: Produces eye damage after contact.
D-CMR effects (carcinogenicity, mutagenicity and toxicity to reproduction):
- Carcinogenicity: Based on available data, the classification criteria are not met, as it does not contain substances classified
as dangerous for the effects mentioned. For more information see section 3.
IARC: Non-applicable
- Mutagenicity: Based on available data, the classification criteria are not met, as it does not contain substances classified as
dangerous for this effect. For more information see section 3.
- Reproductive toxicity: May damage fertility or the unborn child
E-Sensitizing effects:
- Respiratory: Based on available data, the classification criteria are not met, as it does not contain substances classified as
dangerous with sensitising effects. For more information see section 3.
- Cutaneous: Prolonged contact with the skin can result in episodes of allergic contact dermatitis.
F-Specific target organ toxicity (STOT) - single exposure:
Based on available data, the classification criteria are not met, as it does not contain substances classified as dangerous for
this effect. For more information see section 3.
G-Specific target organ toxicity (STOT)-repeated exposure:
- Specific target organ toxicity (STOT)-repeated exposure: Based on available data, the classification criteria are not met, as
it does not contain substances classified as dangerous for this effect. For more information see section 3.
- Skin: Based on available data, the classification criteria are not met, as it does not contain substances classified as
dangerous for this effect. For more information see section 3.
H-Aspiration hazard:
Based on available data, the classification criteria are not met, however it does contain substances classified as dangerous for
this effect. For more information see section 3.
Other information:
Non-applicable
Specific toxicology information on the substances:
Identification Acute toxicity Genus
Distillates (petroleum), hydrotreated light (60 C < fp < 93 C) LD50 oral >5000 mg/kg
CAS: 64742-47-8 LD50 dermal >5000 mg/kg
LC50 inhalation >20 mg/L (4 h)
Cobalt bis(2-ethylhexanoate) LD50 oral >5000 mg/kg
CAS: 136-52-7 LD50 dermal >5000 mg/kg
LC50 inhalation >5 mg/L (4 h)
SECTION 12: ECOLOGICAL INFORMATION
The experimental information related to the eco-toxicological properties of the product itself is not available
12.1Ecotoxicity (aquatic and terrestrial, where available):
Not available
12.2Persistence and degradability:
Not available
12.3Bioaccumulative potential:
Not available
12.4Mobility in soil:
Not available
12.5Results of PBT and vPvB assessment:
Non-applicable
12.6Other adverse effects:
Page 7/10Date of compilation: 7/2/2018 Revised: 1/16/2020 Version: 5 (Replaced 4)
– CONTINUED ON NEXT PAGE –
Duroct Cobalt 12%
Safety data sheet
according to 29 CFR 1910.1200
SECTION 12: ECOLOGICAL INFORMATION (continued)
Not described
SECTION 13: DISPOSAL CONSIDERATIONS
13.1Disposal methods:
Waste management (disposal and evaluation):
Consult the authorized waste service manager on the assessment and disposal operations. In case the container has been in
direct contact with the product, it will be processed the same way as the actual product. Otherwise, it will be processed as non-
dangerous residue. We do not recommended disposal down the drain. See epigraph 6.2.
Regulations related to waste management:
Legislation related to waste management:
40 CFR Part 261- IDENTIFICATION AND LISTING OF HAZARDOUS WASTE
SECTION 14: TRANSPORT INFORMATION
DOT
49CFR 173.150: Combustiible liquid. It can be shipped as non hazardous material if the container is under 119 gallons.
Under 49CFR 171.4, Except when transporting aboard a vessel, the requirements of this subchapter specific to marine
pollutants do not apply to non-bulk packagings transported by motor vehicles, railcars and aircraft.
Transport of dangerous goods by land:
With regard to 49 CFR on the Transport of Dangerous Goods:
14.6
14.4
14.3
14.2
14.1
see section 9Physico-Chemical properties:
IIIPacking group, if applicable:
3Labels:
3Transport hazard class(es):
Combustible liquid, n.o.s. (Cobalt bis(2-ethylhexanoate))UN proper shipping name:
UN number: NA1993
Marine pollutant: Yes14.5
Transport in bulk (according
to Annex II of MARPOL
73/78 and the IBC Code):
Non-applicable14.7
Special precautions which a user needs to be aware of, or needs to comply with, in
connection with transport or conveyance either within or outside their premises
Transport of dangerous goods by sea:
With regard to IMDG 39-18:
14.6
14.4
14.3
14.2
14.1
see section 9Physico-Chemical properties:
IIIPacking group, if applicable:
9Labels:
9Transport hazard class(es):
ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.
(Cobalt bis(2-ethylhexanoate))
UN proper shipping name:
UN number: UN3082
Marine pollutant: Yes14.5
Transport in bulk (according
to Annex II of MARPOL
73/78 and the IBC Code):
Non-applicable14.7
Special precautions which a user needs to be aware of, or needs to comply with, in
connection with transport or conveyance either within or outside their premises
Transport of dangerous goods by air:
With regard to IATA/ICAO 2020:
Page 8/10Date of compilation: 7/2/2018 Revised: 1/16/2020 Version: 5 (Replaced 4)
– CONTINUED ON NEXT PAGE –
Duroct Cobalt 12%
Safety data sheet
according to 29 CFR 1910.1200
SECTION 14: TRANSPORT INFORMATION (continued)
14.6
14.4
14.3
14.2
14.1
see section 9Physico-Chemical properties:
IIIPacking group, if applicable:
9Labels:
9Transport hazard class(es):
ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.
(Cobalt bis(2-ethylhexanoate))
UN proper shipping name:
UN number: UN3082
Marine pollutant: Yes14.5
Transport in bulk (according
to Annex II of MARPOL
73/78 and the IBC Code):
Non-applicable14.7
Special precautions which a user needs to be aware of, or needs to comply with, in
connection with transport or conveyance either within or outside their premises
SECTION 15: REGULATORY INFORMATION
SARA Title III – Toxic Chemical Release Inventory Reporting (Section 313): Cobalt bis(2-ethylhexanoate)
California Proposition 65 (the Safe Drinking Water and Toxic Enforcement Act of 1986): Non-applicable
The Toxic Substances Control Act (TSCA) : Cobalt bis(2-ethylhexanoate) ; Distillates (petroleum), hydrotreated light (60 C < fp
< 93 C)
Massachusetts RTK - Substance List: Cobalt bis(2-ethylhexanoate)
New Jersey Worker and Community Right-to-Know Act: Cobalt bis(2-ethylhexanoate)
New York RTK - Substance list: Cobalt bis(2-ethylhexanoate)
Pennsylvania Worker and Community Right-to-Know Law: Cobalt bis(2-ethylhexanoate)
CANADA-Domestic Substances List (DSL): Cobalt bis(2-ethylhexanoate) ; Distillates (petroleum), hydrotreated light (60 C < fp <
93 C)
CANADA-Non-Domestic Substances List (NDSL): Non-applicable
NTP (National Toxicology Program): Non-applicable
Minnesota - Hazardous substances ERTK: Cobalt bis(2-ethylhexanoate)
Rhode Island - Hazardous substances RTK: Non-applicable
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1096): Non-applicable
Hazardous substances release notification under CERCLA sections 102-103 (40 CFR Part 302): Non-applicable
Specific provisions in terms of protecting people or the environment:
It is recommended to use the information included in this safety data sheet as data used in a risk evaluation of the local
circumstances in order to establish the necessary risk prevention measures for the manipulation, use, storage and disposal of this
product.
Other legislation:
The Toxic Substances Control Act (TSCA)
Occupational Safety and Health Standards (1910 Subpart Z - Toxic and Hazardous Substances)
15.1Safety, health and environmental regulations specific for the product in question:
SECTION 16: OTHER INFORMATION
Legislation related to safety data sheets:
This safety data sheet has been designed in accordance with Appendix d to 1910.1200 - Safety data sheets
Texts of the legislative phrases mentioned in section 2:
H319: Causes serious eye irritation
H360: May damage fertility or the unborn child
H317: May cause an allergic skin reaction
H227: Combustible liquid
Advice related to training:
Minimal training is recommended to prevent industrial risks for staff using this product, in order to facilitate their comprehension
and interpretation of this safety data sheet, as well as the label on the product.
Principal bibliographical sources:
Occupational Safety & Health Administration (OSHA).
Abbreviations and acronyms:
Page 9/10Date of compilation: 7/2/2018 Revised: 1/16/2020 Version: 5 (Replaced 4)
- CONTINUED ON NEXT PAGE -
Duroct Cobalt 12%
Safety data sheet
according to 29 CFR 1910.1200
SECTION 16: OTHER INFORMATION (continued)
IMDG: International maritime dangerous goods code
IATA: International Air Transport Association
ICAO: International Civil Aviation Organisation
COD: Chemical Oxygen Demand
BOD5: 5-day biochemical oxygen demand
BCF: Bioconcentration factor
LD50: Lethal Dose 50
CL50: Lethal Concentration 50
EC50: Effective concentration 50
Log-POW: Octanol-water partition coefficient
Koc: Partition coefficient of organic carbon
ManufacturerDisclaimer:Theinformationcontainedinthissafetydatesheet( SDS )isbasedonsources,technicalknowledgeandcurrentlegislation.Furthermore,isbasedondatabelievedto
beaccurate;thus,thecompanydoesnotassumeanyliabilityforitsaccuracy.Theinformationprovidedhereincannotbeconsideredaguaranteeofthepropertiesofthisproductandthesameis
simplyadescriptionofthesecurityrequirements.Theuse,occupationalmethodologyand/orconditionsforusersofthisproductarenotwithinourawarenessorcontrol.Itisultimatelythe
responsibilityoftheuser(s)totakethenecessarymeasurestoobtainthelegalrequirementsconcerningthemanipulation,storage,useanddisposalofchemicalproducts.Theinformationofthis
SDSonlyreferstothisproduct,whichshouldnotbeusedforpurposesotherthanthosespecified.Finally,themannerinwhichthisproductisusedandwhetherthereisanyinfringementof
patentsisthesoleresponsibilityoftheuser(s).
Page 10/10Date of compilation: 7/2/2018 Revised: 1/16/2020 Version: 5 (Replaced 4)
END OF SAFETY DATA SHEET