39COOLSHOT_TDS.pdf

PRODUCT PROPERTIES
All time calculations are based on temperatures of 77 F, 25 C
Color clear (high solids)
V.O.C <52% monomer Weight per gallon 8.6 lbs/gal FEATURES GEL TIME EXTENSION Slightly slow the catalyzed pot life by adding COOLSHOT at at 3:1 blend. COMPATIBLE CHEMISTRY Designed to work along with the DuraKote gelcoats and Duratec polyester primers. STAY C HILL Longer gel time makes it easier to use the gelcoats or primers in higher temperatures or where large amounts will be mixed at one time. TACK FREE FINISH COOLSHOT enables gelcoat to form a smooth, hard surface film. COLOR NOTE: Adding 39COOLSHOT to an opaque coating will reduce the opacity of the coating. This may cause an apparent color change. Before any repair test the mixture to determine if there is enough opacity to achieve a satisfactory repair. DURATEC COOLSHOT A HIGH QUALITY ADDITIVE FOR GELCOAT REPAIR P ROD UCT # 39 COOLSHOT S A FE TY & H ANDL I NG Duratec COOL SHOT is extremely flammable. Do not apply near sparks, open flames or heat. Keep area ventilated. D o not smoke. Avoid continuous breathing of vapor. Duratec COOLSHOT contains ingredients which coul d be harmful if mishandled. Contact with skin a nd eyes should be avoided and necessary protective equipment and clothing should be worn. Individuals should wash with soap and water before eating or drinking. All containers should be properly labeled t o prevent accidental ingestion or improper disposal. Individuals should reseal any partly used material back in the container. S tore under cool, dry conditions and away from open flames and high temperatures. For more detailed instructions on storage, please see the MSDS sheet. DE S CRIPTION A n additive designed to accelerate the s urface cure of and overcome the oxygen inhibition of the Durakote gelcoat series or other polyester gelcoats. I t can also be used to slow gel time in Duratec polyester primers. COOLSHOT will increase the gel and cure time by ~1 0% and enables gelcoat to form a smooth, hard s urface film. 909-546-1160 hawkeyesales@hawkeyeind.com PO BOX 415, BLOOMINGTON, CA 92316 WWW.DURATEC1.COM APPLICATION INSTRUCTIONS 5.Spray pressures should be 35-50 PSI. If pressure pot is used, provided 10-15 psi pot pressure. 6.Spray the entire surface to be repaired with a fine mist coat, and wai 2 minutes for t he solvents to fl off. 7.Fol low with wet coats, overlapping the surroundi ng area to ensure complete coverage. When re-spraying large areas, keep a wet edge with a sta ndard gelcoat spray technique. 8.When the material has cured (~1 hour), lightly sand with 320-800 grit wet or dry sandpaper. Allow coating to breathe for at least another hour after sanding. 9.After open breathi ng period, buff surface to desired finish. AquaBuff 1000F Fast-Cut Compound and AquaBuff 2000 Polish is recommended. BEAT THE HEAT & EXTEND GEL TIME. COOLSHOT 3:1 RATIO GELCOAT TO ADDITIVE 1.39COOLSHOT is ready to use as received. 2.Thoroughly sand the area to be repaired to a 120 or 180 grit finish. Ensure surface is cleaned well to remove a ny contaminating substances. Select a high quality gelcoat of the appropriate color. We recommend a small gel time mixture be done to determine specific gel time for existing shop conditions. 3.Add COOLSHOT R epair Additive a t a 3:1 ratio (Gelcoat to Additive) to the gelcoat prior to use. Thoroughly mix before using. 4.Catalyze the combined mixture as recommended, at 2% by weight with MEKP (Norox 925 is a good choice.) Mix thoroughly. *39COOLShot will reduce the gel coat or Duratec. If additional thinning is needed, thi n 5% by weight with Duratec 39UCE, MEK, or virgin acetone.