ENTERPRISES
SAFETY DATA SHEET
TC.157O PART A
Page
‘l
ot /
Date Issued : 0211312014
SDS No : TC-1570 PART A
Date Revised : 0V 1312020
Revision No :2WB
r. PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: TC-l570 PART A
GENERAL USE: Epoxy resin
MANTJFACTURER
BJB Enterprises, Inc.
14791 Franklin Avenue
Tustin, C492780
Emergency Phone: (114) 73+8450
24 HR. EMERGENCY TELF-PHONE NI.]MBERS
CHEMTREC (USA & Canada): (800) 424-9300
or (703) 527-3887 CCl# 2820
2. HA ZARDS IDENTIFICATION
GHS CI.ASSIFICATIONS
Health:
Skin Irritation, Category 2
Serious Eye Damage Category I
Skin Sensitization, Category I
Environmental:
Chronic Hazards to the Aquatic Environment, Category 2
GHS I-ABEL
CorrosionExclamation Environment
mark
SIGNAL WORD: DANGER
HAZARD STATEMEITS
H315: Causes skin irritation.
H318: Causes serious eye damage.
H3l7:.May cause an allergic skinreaction.
H411 : Toxic to aquatic life with long lasting effects.
PRE CAU TI ONARY STATWI ENTS
Prevention:
P2 6 I : Av oi d breathi ng dust/fu me/gas/mi st/v ap ours /spray.
P264: Wash thoroughly after handling.
P272: Contaminated work clothing should not be allowed out of the workplace.
P280: Wearprotective glovesfurotective clothing/eye protection/face protection.
P213: Avoid release to the environment.
Response:
P3A+P352: IF ON SKIN: Wash with plenty of soap and water.
P333+P313: If skin initation orrashoccurs: Get medical advice/attention.
P362+P364: Take off contaminated clothing and wash it before reuse.
P305+P35 1+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do
Continue rinsing.
t
I
Page2oI /
TC.157O PART A
P3 I 0 : Immediately call a POI SON CENTER/d octor/physici an.
P39l : Collect spillage.
Disposal:
P501 : Dispose of contents/container in accordance with local/regional/national/international regulations
3. COMPOSITION / INFORMATION ON INGREDIENTS
Chemical Name Wt.Vo CAS
Barium sulfate 40-707727-43-1
2,2′-[( 1-methylethylidene)bis(4, I -phenyleneoxymethylene)] bisoxirane 10- 30 1615-54-3
Titanium dioxi de (IiO2) 3-7 13463-61-1
Oxirane, 2,2′ -11,4-butanediylbis(oxym ethylene) lbis-
1-5 2425-79-8
4. FIRST AID MEASURBS
EYES: Immediately flush with plenty of water. After initial flushing, remove any contact lenses and continue flushing for at least 15 minutes.
Get medical advice/attention.
SKIN: Immediately wash skin with soap and plenty of water. Remove contaminated clothing. Get medical advice/attention if irritation or rash
develops. Wash clothing before reuse.
INGESTION: If swallowed, call a physician immediately. Do not induce vomiting unless directed to do so by medical personnel. Provided the
patient is conscious, wash out mouth with water. Never give anyttring by mouth to an unconscious person.
INHALATION: Remove to fresh air. If not breatlring, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or
oxygen by nained personnel. Get immediate medical attention.
NOTES TO PHYSICIAN: Symptomatic and supportive therapy as needed. Following severe exposure medical follow-up should be
monitored for at least 48 hours.
5. FIRE FIGIITING MEAST]RES
EXTINGUISHING MEDIA: Water spray, carbon dioxide, dry chemical, or foam.
HAZARDOUS COMBUSTION PRODUCTS: Carbon monoxide and carbon dioxide.
FIRE FIGHTING PROCEDURES: Cool fire exposed containers with water spray. Remove containers from the fire area if possible. Do not
release runoff from fire control methods to sewers or waterways.
FIRE FIGHTING EQUIPMENT: Firefighters should wear positive pressure self-contained breathing apparatus (SCBA) and consider use of
unmanned hose holders or monitor nozzles for fighting large fires’
6. ACCIDENTAL RELEASE MEASURF^S
SPILL AND LEAK PROCEDURES: Evacuate unnecessary personnel from the spill area. Eliminate all sources of ignition. Ensure adequate
ventilation. Use personal protective equipment. Dike and contain spill. Prevent product from entering drains or waterways. Absorb with non-
combustible material (such as sand, earth, diatomaceous earth, orvermiculite) and transferto a containerfor disposal according to
locaVnation al regulations.
ENVIRONMENTAL PRECAUTIONS
WATER SPILL: Do not discharge into drains, surface waters, or groundwater.
GENERAL PROCEDIJRES: Refer to section 8 of SDS for personal protection details.
RELEASE NOTES: Composition and extent of any spill should be evaluated against local regulations and reported to the proper agencies, if
necessary.
7. IIANDLING AND STORAGE
GENERAL PROCED{.IRES: Avoid contact wit}r eyes, skin and clothing. Use only with adequate ventilation. Avoid breathing vapor over
open containers. Avoid open container exposure to damp air. Avoid breathing aerosols, mists, and vapors.
HANDLING: Use appropriate personal protective equipment as specified in Section 8. Handle in a well-ventilated area. Handle and use in a
manner consistent with good industriaVmanufacnrring techniques and practices’
Page 3 ot /
TC-1570 PART A
STORAGE: Store in a dry and well-ventilated place, away from excessive heat, in original or similar container. Avoid unnecessary contact.
Protect from lieezing. Containers should be tightly sealed to prevent contamination with foreign materials.
STORAGE TEMPERATURE: 65-80’F (l 8 -21′ C)
SHELF LIFE: l2 months from date of shipment under manufacturers recommended storage conditions.
8. E)POSURE CONTROLS / PERSONAL PROTECTION
osHA HAZARDOUS COMPONENTS (29 CFR19r0.r200)
EXPOSURE LIMITS
Chemical Name Type ppm mdm3
TWA
_ tll151 5p ttl
OSTIA PEL
STEL
TWA 10
ACGIH TLV
STEL
NIOSH IDLH
_ tll191 5p ttlTWA
Barium sulfate
NIOSH REL STEL
TWA
OSHA PEL
STEL
TWA
ACGIH TLV
STEL
TWA
2,2′-[( 1-methylethylidene)bis(4, l-phenyleneoxymethylene)] bisoxirane
NIOSH REL
STEL
TWA
l2l
15
t2l
OSHA PEL
STEL
TWA 10
ACGIH TLV
STEL
TWA
Titanium dioxide (IiO2)
NIOSH REL
STEL
TWA
OSIIA PEL
STEL
TWA
ACGIH TLV
STEL
TWA
Oxirane, 2,2′ -ft,4 -btttwrediylbis(oxymethylene)lbis-
MOSH REL
STEL
Footnotes:
1. T = Total dust, R = Respirable fraction
2. Total dust
EXPOSURE G
ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airbome levels
below recommended exposure limits.
PERSONA L PROTECTIVE EQUIPMENT
EYES AND FACE: Safety goggles or glasses are recommended. Plastic face shields should be used for complete face protection to protect
Page 4 ol /
TC.157O PART A
against possible splashing or spraying of material. ANSI 287.1 or approved equivalent.
SKIN: Chemical-resistant gloves and chemical goggles, face-shield, and synthetic apron or coveralls should be used to prevent contact with
eyes, skin, or clothing. Wem nitrile or neoprene gloves. Chemical resistant gloves lined with polyethylene offer maximum protection.
RESPIRATORY: Exhaust ventilation recommended. An organic vapor cartridge or fresh air supplied respirator (NIOSH approved) may be
necessary for certain applications. Consider the type of application, environmental concentrations, and other materials being used
concurrently when determining respirator use and s election. Observe OSHA regulations for respirator use (29 CFR 19 I 0.1 34).
PROTECTfVE CLOTHING: Protective clothing should be selected and used in accordance with’Guidelines for the Selection of Chemical
Protective Clothing’ published by ACGIH.
WORK HYGIENIC PRACTICES: Contaminated clothing should be changed and washed before reuse. Eating, drinking and smoking in
immediate work area should be prohibited. Wash hands before eating.
OTHER USE PRECAUTIONS: Facilities storing or utilizing this material should be equipped with an eyewash facility and a safety shower’
Training is important. Follow all label precautions.
9. PHYSICAL AND CHEIVIICAL PROPERTTES
PHYSICAL STATE: Paste-LiKe
ODOR: Slight
COLOR: White
pH: No data available
FLASH POINT AID METHOD: > 200″C (392″F) Pensky-Martens CC
VAPORPRESSURE: No data available
VAPORDENSITY: No data available
BOILING POINT: No data available
SOLLJBILITY IN WATER: Insoluble
SPECIFIC GRAVITY:2.1 (water=l) at25oC Q1″n
VISCOSITY #1: 160000 Centipoise at25″C Q1’m
(VOC): Nil
10. STABILITY AND REACTTVITY
REACTMTY: Hazardous reactions will not occur under normal transport or storage conditions.
STABILITY: This product is stable under normal ambient conditions of temperature and pressure
CONDITIONS TO AVOID: No data available
POSSIBILITYOF HAZARDOUS REACTIONS: No data available
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide and carbon dioxide.
INC OMPATIBLE MATERIALS: Oxidizing agents
11. TOXICOLOGICAL INFORMATION
ACUTE TOXICITY
Chemical Name ORAL LDso DERMAL LDsO INHALATIONLCM
Barium sulfate No data availableNo data available No data available
2,2′ -f(l-methylethylidene)bis(4, 1-
pheny len eoxymethylene) lbi soxirane
> 5000 mglkg Rat> 2000 mg/kg Rabbit13.M mg/l Rat (4 h)
Titanium dioxide (IiO2) > 10000 mglkg Rat No data available> 6.82mgfl Rat (4 h)
Oxirane, 2,2′ -11,4-bttanediylbis(oxymethylene)lbis- 1410 mg/kg Rat> 2l5O mg/kgRabbit No data available
SKIN CORROSION/IRRITATION: Causes skin initation.
SERIOUS EYE DAMAGE/IRRITATION: Causes serious ey e dama ge.
RESPIRATORY OR SKIN SENSITISATION: May cause sensitization by skin contacl
Page 5 ol /
TC.157O PART A
GERM CELL MUTAGENICITY: No data available
CARCINOGENICITY
Chemical Name
IARC Status
2,2′-[( 1-methylethylidene)bis(4,1-phenyleneoxymettrylene)]bisoxirane
J
Titanium dioxide (Ti02) 2B
REPRODUCTIVE TOXICITY: No data available
STOT-SINGLE EXPOSURE: No data available
STOT-REPEATED EXPOSURE: No data available
ASPIRATION HAZARD: No data available
12. ECOLOGICAL INFORMATION
EI{VIRONMENTAL DATA: This product may cause risk of hazardous effects to the environment.
ECOTOXICOLOGICAL INFORMATION: Toxic to aquatic organisms, may causelong-term adverse effecs in the aquatic environment.
Avoid release to the environment.
BIOACCUMUI-ATION/ACCUMULATION: No data available
DISTRIBUTION: No data available
CIIELICAL FATE INFORMATION: No data available
13. DISPOSAL CONSIDERATIONS
DISpOSAL METHOD: The generation of waste should be avoided or minimized wherever possible. Empty containers or liners may retain
some product residues. This material and its container must be disposed of in a safe way. Dispose of surplus and non-recyclable producs via
a licensed waste disposal contractor. Disposal of this product, solutions and any by-products should at all times comply with the requirements
of environmental protections and waste disposal legislation and any regional local authorityrequirements. Avoid dispersal of spilled material
and runoff and contact with soil, waterways, drains and sewers.
14. TRANSPORT INFORMATION
DOT (DEPARTMENT OF TRANSPORTATION)
PROPER SHIPPING NAME: Environmentally hazmdous substance, liquid, n.o.s. (See Note)
TECHNICAL NAME: Bisphenol A epoxy resin
PRIMARY HAZARD CLASSiDIVISION : 9
UN/NANUMBER: tlN3082
PACKINGGROI.]P: Itr
NAERG:171
LABEL: Class 9 (miscellaneous hazardous materials)
MARINE POLLUTANT #1: Yes
OTHER SHIPPING INFORMATION : Only regulated for bulk and vessel shipments, per 49CFR 17 1.4 (c) Exceptions. Except when all or
part of the transportation is by vessel, the requirements of this subchapter specific to marine pollutants do not apply to non-bulk
packagings tansported by motor vehicle, rail car, or aircraft’
AIR (ICAO/IATA)
SHIPPING NAME: Environmentally hazardous substance, liquid, n’o’s. (See Note)
TECHMCAL NAME: Bisphenol A epoxy resin
LINNANUMBER: UN3082
PRIMARY HAZARD CLASS/DMSION: 9
PACKING GROUP: Itr
ERG:9L
LABEL: Class 9 (miscellaneous hazardous materials)
Page b oI /
TC.Is7O PART A
NOTE: Orrly regulatecl fbr bulk and vessel shipments, per 49CFR 17 L4 (c) Exceptions. Except when all or piu’t of the transportation is by
vessel. the requirements ol’this subchaptel specific to marine pollutants do not apply to non-bulk packagings tlansported by rnotor vehicle,
lail car. ol aircrali.
VESSIiI, (IMO/IMDG)
SHIPPI NG NA ME : Envi lonnren tally hazar dous substance, I iq uid, n.o. s.
TECHNICAI NAME: Bisphenol A epoxy resin
UN/NA NUMtsIlR: LlN3082
PRIMARY HAZARD CI,ASS/DIVISION: 9
PACKING GIIOUP: I]I
EnS: F-A, S-F
MARINE POLLUTANT #1: Yes
LAIIEL: Clnss 9 (rniscellaneous hazardous materials)
r5. REGT]LATORY INFORMATION
UNI’|I’D STA’TES
SARA TITLE III (SI]PERFUND AMENDMENTS AND REAUTHORI ZATION A CT)
3lll3l2 HEALTH HAZARDS: Referto Section 2forhazard clzssification.
3f3 REPORTABLE INGREDIENTS: This product does not contain any substances subject to the reporting requirements of Section
313 ol Title III o1’the Superf’und Amendments and Reauthorization Act of 1986 and 40 CFR Part 372.
CI’RCI,A (COMPREHENSIVE ENVIRONMENTAL RESPONSE, COMPENSATION,ANDLIABILITY ACT)
CERCLA REGIILATORY: This product does not contain any substances regulated as a hazar dous sttbstance under the Comprehensive
Envilonmental Response Compensation and Liability Act (CERCI-A) (40 CFR 302).
TSCA (TOXIC STJBSIhNCE CONTROL ACT)
TSCA REGULATORY: This product does not contain any substances subject toTSCA Section l2(b) export notification.
TSCA STATUS: This product orits components are listed inorexempt liom theTSCA inventory requirements.
CLEAN AIR ACT
Chemical Name WtVo CAS
Epichlorohydrin 1 06-89-8
OCC UPATIONA L S AFETY AND HEA LTH ADMINISTRATION (OSHA
)
29 CFR1910.1I9—PROCF^SS SAFETYMANAGEMENTOF HIGHLYHAZARDOUS CHEMICAIf: None of the chemicals in
this product are considered highly hazat dous by OSHA.
CALIFORNIA PROPOSITION 65: A WARNING: This product can expose you to chemicals including [see table below], which is [are]
known [o the Stateof California to cause cancerand birth defecls or other reproductive harm. Formore information, go to
www.P65Wan.rin gs.ca.gov.
Chemical Name WLVo Listed
Titaniu n.r dioxide (Ti02) o Cancer
Epichlorohyddn
o Cancer
o Male Reproductive
OSHA HAZARD COMM. RULE: The contents of the SDS comply with the OSHA Hazard Communication Standard 29 CFR 1910.1200.
CANADA
WHMIS (WORKPLACE HAZARDOUS MATERIALS INFORMATION SYSTEM): This product ha.s been classified according to the
hazard criteria of the CPR and the SDS contains all the information required by the CPR.
DOMFSTIC SUBSTANCE LIST (INVENTORY): All components in this product arc listed in ol exempted frorn the Domestic
Substances List (DSL) or the Non-Domestic Substances List (NDSL).
GIINERAL COMMENTS: No data available
Page / ot /
TC.157O PART A
16. OTHER INFORMATION
REASON FOR ISSUE: Revision
Date Revis ed z 021 1 312020
REVISION SUMMARY: This SDS replaces the02/l5D0l7 SDS.
HMISRATING NFPA CODES
HMIS RATINGS NOTES: Personal Protection: See Section 8
MANUFACTURER DISCLAIMER: This information is furnished without wan’anty, expressed ol implied, except that is accurate to the best
knowledge of BJB Enterprises,Inc. The dataon this sheet relates only to the specific material designated herein. BJB Enterprises, Inc.
assumes no legal responsibility for use or reliance upon this data.
XPERSONAL PROTECTION
HEALTH
FLAillMAI}ILITY
BTB
ENTERPRISES
SAFETY DATA SHEET
TC-1570 PART B
Page 1 ot /
Date Issued :0AB/2014
SDS No : TC-1570 PART B
Date Revised : 0A 13/2020
Revision No :2
1. PRODUCT AND COMPANY IDEIYTIFICATION
PRODUCT NAME: TC-I570 PART B
GENERAL USE: Epoxy curing agent
MANUFACTURER
BJB Enterprises, Inc.
14791 Franklin Avenue
Tustin, CAgn80
Emergency Phone: (114) 73+U50
24 HR. EMERGENCY TELEPHONE N{.]MBERS
CHEMTREC (USA & Canada): (800) 424-9300
or (703) 527-3887 CCN# 2820
2. HAZARDS IDENTIFICATION
GHS CLASSIFICATIONS
Health:
Acute Toxicity (Oral), Category 4
Acute Toxicity ( Inhalation), Category 2
Skin Corrosion, Category I
Serious Eye Damage Category 1
Skin Sensitization, Category I
Reproductive Toxicity, Category I
Target Organ Toxicity (Single exposure), Category 3
Environmental:
Chronic Hazards to the Aquatic Environment, Category 2
GHS I-ABEL
Skull and
crossbones
Corrosion Healthhazard Environment
SIGNAL WORD: DANGER
HAZARD STATEMENTS
H302: Harmful if swallowed.
H330: Fatal if inhaled.
H3 14: Causes severe skin burns and eye damage.
H3 17: May cause an allergic skin reaction.
H360: May damage fertility or the unbom child.
H335: May cause respiratory irritation.
H4l I : Toxic to aquatic life with long lasting effects.
PRECAUTI ONARY STATEMENTS
Prevention:
P201 : Obtain special instructions before use.
PZA: Do not handle until all safety precautions have been read and understood.
P2 60 : Do n ot breath e du st/fu me/gas/mist/vapours/spr ay.
P27l: Use only outdoors or in a well-ventilated area.
lLs
Page:2oI /
TC-1570 PART B
PZM: ln case of inadequate ventilation wear respiratory protection.
P264 : Wash thoroughly aft er h andling.
P2l0: Do not eat, drink or smoke when using this product.
P212: Contaminated work clothing should not be allowed out of the workplace.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P273: Avoid release to the environment.
Response:
P301+P33GFP331 : IF SWALLOWED: Rinse mouth. Do NOT induce vomiting.
p303+p361+p353: IFON SKIN (orhair): Take off immediately all contaminated clothing. Rinse skin with water or shower.
P363: Wash contaminated clothing before reuse.
P304+P340: IF INHALED: Remove person to fiesh air and keep comfortable for breathing.
p305+p35
1+p338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.
Continue rinsing.
P3 10 : Immediately call a POISON CENTER/doctor/physician.
P308+P31 3: IF exposed or concerned: Getmedical advice/ attention’
P391 : Collect spillage.
Storage:
P403+P233: Store in a well-ventilated place. Keep container tightly closed.
P405: Store locked up.
Disposal:
P501 : Dispose of contents/container in accordance with local/regional/national/international regulations.
3. COMPOSITION / INFORMATION ON INGREDIENTS
Chemical Name
WITo CAS
Polyamine adduct
30- 60Proprietary
1,2-Eth anediamine, N- (2- aminoethyl)-
l5 –
,10 I1140-0
4,4′ -Isopropyli den edipheno I l0- 30 80-05-7
4. FIRST AID MEASURE.S
EyES: Immediately flush with plenty of water. After initial flushing, remove any contact lenses and continue flushing for at least 15 minutes.
Get medical advice/attention.
SKIN: Immediately wash skin with soap andplenty of water. Remove contaminated clothing. Getmedical attention immediately. Wash
clothing before reuse.
INGESTION: If swallowed, call a physician immediately. Do NOT induce vomiting. Provided the patient is conscious, wash out mouth with
water. Never give anything by mouth to an unconscious person.
INHAI-ATION: Remove to fresh air. If not breathing, if breathing is irregular or if respiratory arrqstoccurs, provide artificial respiration or
oxygen by ftained personnel. Get immediate medical attention.
NOTES TO PHYSICIAN: Symptomatic and supportive therapy as needed. Following severe exposure medical follow-up should be
monitored for at least 48 hours.
5. FIRE FIGHTING MEASURES
EXTINGUISHING MEDIA: Water spray, carbon dioxide, dry chemical, or alcohol-resistant foam.
HAZARDOUS COMBUSTION PRODUCTS: Carbon monoxide, carbon dioxide nitrogen oxides, nitric acid, ammoni4 aldehydes,
nitrosamine, and chlorine.
FIRE FIGHTING PROCEDURES: Cool fire exposed containers with water spray. Remove containers from the fire area if possible. Do not
release runoff from fire control methods to sewers or waterways.
FIRE FIGHTING EeUIpMENT: Firefighrers should wear positive pressure self-contained breathing apparatus (SCBA) and consider use of
unmanned hose holders or monitor nozzles for fighting large fires.
6. ACCIDENTAL RELEASE MEASURES
Page 3 ot /
TC.1570 PART B
SPLL AND LEAK PROCEDURBS: Evacuate unnecessary personnel from the spill area. Eliminate all sources of ignition. Ensure adequate
ventilation. Use personal protective equipment. Dike and contain spill. Prevent product from entering drains or waterways. Absorb with non-
combustible material (such as sand, earth, diatomaceous earth, orvermiculite) and transferto a containerfor disposal according to
I ocaVnational regulations.
EI{VIR ONM EN TAL PRECA UTIONS
WATER SPILL: Do not discharge into drains, surface waters, or groundwater.
GENERAL PROCEDURES: Refer to section 8 of SDS forpersonal protection details.
RELEASE NOTES: Composition and extent of any spill should be evaluated against local regulations and reported to the proper agencies, if
necessary.
7. HANDLINGANDSTORAGE
GENERAL PROCEDURES: Avoid contract with eyes, skin and clothing. Use only with adequate ventilation. Avoid breathing vapor over
open containers. Avoid open container exposure to damp air. Avoid breathing aerosols, mists, and vapors.
HANDLING: Use appropriate personal protective equipment as specified in Section 8. Handle in a well-ventilated area. Handle and use in a
manner consistent with good industriaVmanufacturing techniques and practices.
STORAGE: Store in a dry and well-ventilated placg away from excessive heat, in original or similar container. Avoid unnecessary contact.
Protect from fieezing. Containers should be tightly sealed to prevent contamination with foreign materials.
STORAGE TEMPERATURE: 65-80’F (1 8 -n’ C)
SHELF LIFE: 12 months from date of shipment under manufacturers recommended storage conditions.
8. E)(POSURE CONTROLS / PERSONAL PROTECTION
Page 4 ol /
TC-1570 PART B
osHA HAZARDOUS COMPONENTS (29 CFRl910.1200)
EXPOSURE LIMITS
ppm -d-tChemical Name Type
TWA
STEL
OSHA PEL
TWA
ACGIHTLV
STEL
TWA
NIOSH REL
STEL
Polyamine adduct
TWA 1 4
OSHA PEL
STEL
ITWA
ACGIH TLV
STEL
4 tllTWA I tl1
NIOSH REL
STEL
1,2-Ethanedi amine, N- (2- aminoethyl)-
TWA
OSIIA PEL
STEL
TWA
STEL
ACGIH TLV
TWA
STEL
4,4′ -Isopropyli d en edipheno I
MOSH REL
Footnotes:
l. Skin
ENGIIYEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne levels
b elow recom mended exposure limits.
PERSONAL PROTECTTVE EQUIPMENT
EYES AND FACE: Safety goggles or glasses are recommended. Plastic face shields should be used for complete face protection to protect
against possible splashing or spraying of material. ANSI 287.1 or approved equivalent.
SKIN: Chemical-resistant gloves and chemical goggles, face-shield, and synthetic apron or coveralls should be used to prevent contact with
eyes, skin, or clothing. Wear nitrile or neoprene gloves. Chemical resistant gloves lined with polyethylene offer maximum protection.
RESPIRATORY: Exhaust ventilation recommended. An organic vapor carffidge or fresh air supplied respirator (NIOSH approved) may be
necessary for certain applications. Consider the type of application, environmental concentrations, and other materials being used
concurrently when determining respirator use and selection. Observe OSHA regulations for respirator use (29 CFR 1910.134).
PROTECTfVE CLOTHING: Protective clothing should be selected and used in accordance with’Guidelines for the Selection of Chemical
Protective Clothing’ published by ACGIH.
WORK HYGIEMC PRACTICES: Contaminated clothing should be changed and washed before reuse. Eating, drinking and smoking in
immediate work area should be prohibited. Wash hands before eating.
OTHER USE PRECAUTIONS: Facilities storing or utilizing this material should be equipped with an eyewash facility and a safety shower.
Training is important. Follow all label precautions.
9. PITYSICAL AND CHEIVIICAL PROPERTIES
PHYSICAL STATE: Viscous liquid
Page 5 ot /
TC.157O PART B
ODOR: Irritating
COLOR: Light yellow
pH: Alkaline
FLASH POINT AND METHOD: 110’C (230″F)
VAPORPRESSLJRE: No data available
VAPOR DEI{SITY: No data available
BOILING POINT: No data available
SOLUBILITY IN WATER: Soluble
SPECIFIC GRAVITY: 1.08 (water=l) at25″C (11″D
VISCOSITY #1:3500 Centipoise at25″C (71’n
(VOC): Nil
10. STABILITY AND REACTTVITY
REACTMTY: Hazardous reactions will not occur under normal transport or storage conditions.
STABILITY: This product is stable under normal ambient conditions of temperature and pressure.
CONDITIONS TO AVOID: No data available
POSSIBILITY OF IIAZARDOUS REACTIONS: No data available
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide, carbon dioxide, nitrogen oxides, nitric acid, ammoni4 aldehydes,
nitrosamine, and chlorine.
INCOMPATIBLE MATERIALS: Sodium hypochlorite, organic acids, mineral acids, oxidizing agents, and nitrous acid.
11. TOXICOLOGICAL INFORMATION
ACUTE TOXICITY
Chemical Name ORAL LDso DERMAL LDsO INHALATIONLCsO
Polyamine adduct No data available No data available No data available
1,2-Ethanediamine, N-(2-aminoethyl)- 1080 mg/kg Rat 1090 mg/kg Rabbit 0.3 mg/l Rat (4 h)
4,4′ -Isopropylidenediphenol > 2000 mg/kg Rat 64ffimlkg Rabbit l70mglm3 Rat (6 h)
SKIN CORROSION/IRRITATION: Causes severe skin burns.
SERIOUS EYE DAMAGE/IRRITATION: Causes serious eye damage.
RESPIRATORY OR SKIN SENSITISATION: May cause sensitization by skin contacl
GERM CELL MUTAGENICITY: No data available
REPRODUCTM TOXICITY: May damage fertility orthe unbom child.
STOT-SINGLE E)POSURE: May cause respiratory irritation.
STOT-REPEATED E)POSURE: No data available
ASPIRATION HAZARD: No data available
12. ECOLOGICAL INFORMATION
ENMRONMENITAL DATA: This product may cause risk of hazardous effects to the environment.
ECOTOXICOLOGICAL INFORMATION: Toxic to aquatic organisms, may causelong-term adverse effects in the aquatic environment.
Avoid release to the environment.
B IOACC UMULA TION/A CCUMULATION: No d ata avai lab le
DISTRIBUTION: No data available
CHEMICAL FATE INFORMATION: No data available
13. DISPOSAL CONSIDERATIONS
Page 6 ot /
TC-1570 PART B
DISPOSAL METHOD: The generation of waste should be avoided or minimized wherever possible. Empty containers or liners may retain
some product residues. This material and its container must be disposed of in a safe way. Dispose of surplus and non-recyclable products via
a licensed waste disposal contractor. Disposal of this product, solutions and any by-products should at all times comply with the requirements
of environmental protections and waste disposal legislation and any regional local authorityrequirements. Avoid dispersal of spilled material
and runoff and contact with soil, waterways, drains and sewers.
14. TRANSPORT INFORMATION
DOT (DEPARTMENT OF TRANSPORTATION)
PROPER S HIPPING NAM E: Di ethyl enetri am ine solu ti on
PRIMARY HAZARD CLASS/DIVISION: 8
UN/NA NUMBER: UN2079
PACKING GROUP: II
NAERG:154
LABEL: Corrosive
AIR (ICAO/IATA)
SHIPPING NA ME : Diethylenetri am ine solution
UN/NA NUMBER: UN2079
PRIMARY HAZARD CLASS/DIVISION : 8
PACKING GROTIP: II
ERG:8L
LABEL: Corrosive
vEssEL (rMo/rMDG)
SHIPPING NAME : Diethylenetriamine solution
UN/NA NUMBER: UN2079
PRIMARY IIAZARD CLASS/DIVISION : 8
PACKING GROT]P: II
EmS: F-A, S-B
LABEL: Corrosive
15. REGTJLATORY INFORMATION
TJNITEDSTATES
SARA TITLE III (ST]PE RFUND A MENDM ENTS AND REAUTHORI ZATION A CT)
3llBl2 HEALTH HAZARDS: Referto Section 2forhazard classification.
313 REPORTABLE INGREDBNTS: This product contains the following substances subject to the reporting requirements of Section
313 of Title trI of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Pat 372:
EPCRA SECTI ON 313 STJPPLTER NOTIFICATION
Chemical Name wt.10CAS
4,4′ -Isopropyli den ediphenol 10- 3080-05-7
CERCLA (COMPREHENSIVE EIWIRONMENTAL RESPONSE, COMPENSATION, AND LIABILITY ACT)
CERCLA REGLILATORY: This product does not contain any substances regulated as a hazardous substance under the Comprehensive
Environmental Response Compensation and Liability Act (CERCI-A) (40 CFR 302).
TSCA (TOXIC SUBSTANCE CONTROL ACT)
TSCA REGULATORY: This product does not contain any substances subject toTSCA Section l2(b) export notification.
TSCA STATUS: This product or its components are listed in or exempt from the TSCA inventory requirements.
OCC UPATIONA L S AFETY AND HEA LTH A DMIN ISTRATION (OSHA )
29 CFRDr0.1I9—PROCESS SAFETY MANAGEMENT OF HIGHLY IIAZARDOUS CHEMICAIS: None of the chemicals in
Page / oI /
TC-1570 PART B
this prodttct are cotrsidered highly haza dous by OSHA.
CALIFORNIA PROPOSITION 65: A WARNING: This product cim expose you to chemicals including Isee table belowl, which is [arel
known to the State of Calil’ornia to caLrse birrh det’ects ol’ other reprodr”rctive halm. For morc infortnation, go to www.P65Warnings.ca.gov.
Chemical Name Wt.Vo Listed
4.4′-lsopropylidenediphenol r0- 30 oFemale Reproductive
OSHA HAZARD COMM. RULE: The conrenrs of the SDS comply with the OSHA Hazard Cornrnunication Standard 29 CFR 1910′ 1200.
CANADA
WHMIS (WORKPLACE HAZARDOUS MATERIALS INFORMATION SYSTEM): This product has been classified according to the
hazard criteria of the CPR and the SDS contains all the information required by the CPR.
DOMESTIC SImSTANCE LIST (INVENTORY): All componerlts in this product are listed in or exen]pted from the Domestic
Substances List (DSL) or the Non-Domestic Sttbstances List (NDSL)’
GENERAL COMMENTS: No data available
16. OTHER INFORMATION
REASON FOR ISSUE: Revision
Date Revis ed : 021 1 3/2020
REVISION SUMMARY: This SDS replaces the 02l152017 SDS
HMIS RATING NFPA CODES
HMIS RATINGS NOTES: Personal Protection: See Section 8
MANUFACTLRER DISCLAIMER: This informarion is fumished without wananty, expressed or implied, except that is accurate to ttre best
knowledge of BJB Enteryrises, Inc. The data on this sheet relates only to the specific material designated herein. BJB Enterprises, Inc’
assumes no legal responsibility for use or reliance upon this data.
XPERSONAL PROTECTION
HEALTH
FLAMMABILITY
IE
E