Page 1/12
Safety Data Sheet
acc. to OSHA HCS
Printing date 10/19/2021 Reviewed on 10/19/2021
53.0
* 1 Identification
Product identifier
Trade name: TCC410 Resin
Article number:I410088
Application of the substance / the mixtureEpoxy resin
Details of the supplier of the safety data sheet
Sika Advanced Resins, US
EHS Department
Manufacturer/Supplier:
Manufacturer:
Sika Advanced Resins
30800 Stephenson Hwy
Madison Heights
MI 48071
USA
Information department:Product safety department
Emergency telephone number:
During normalopening times: +1 (248) 588-2270
CHEMTREC 24-hour Emergency: +1 (800) 424-9300
* 2 Hazard(s) identification
Classification of the substance or mixture
GHS08 Health hazard
Carc. 1A H350 May cause cancer.
GHS07
Skin Irrit. 2 H315 Causes skin irritation.
Eye Irrit. 2A H319 Causes serious eye irritation.
Skin Sens. 1 H317 May cause an allergic skin reaction.
Label elements
GHS label elementsThe product is classified and labeled according to the Globally Harmonized System (GHS).
Hazard pictograms
GHS07GHS08
Signal wordDanger
(Contd. on page 2)
US

Page 2/12
Safety Data Sheet
acc. to OSHA HCS
Printing date 10/19/2021 Reviewed on 10/19/2021
Trade name: TCC410 Resin
(Contd. of page 1)
53.0
Hazard-determining components of labeling:
Reaction Product of Bisphenol A and Epichlorohydrin
Quartz (SiO2)
oxirane, mono[(C12-14-alkyloxy)methyl] derivs
Alkyl C12-C14 Glycidyl Ether
Polyglycol
epichlorohydrin polymer
Hazard statements
Causes skin irritation.
Causes serious eye irritation.
May cause an allergic skin reaction.
May cause cancer.
Precautionary statements
Avoid breathing dust/fume/gas/mist/vapors/spray
Obtain special instructions before use.
Do not handle until all safety precautions have been read and understood.
Avoid breathing dust/fume/gas/mist/vapors/spray
Wash thoroughly after handling.
Contaminated work clothing must not be allowed out of the workplace.
Wear protective gloves/protective clothing/eye protection/face protection.
If on skin: Wash with plenty of water.
If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.
Continue rinsing.
IF exposed or concerned: Get medical advice/attention.
Specific treatment (see on this label).
Take off contaminated clothing and wash it before reuse.
If skin irritation or rash occurs: Get medical advice/attention.
If eye irritation persists: Get medical advice/attention.
Wash contaminated clothing before reuse.
Store locked up.
Dispose of contents/container in accordance with local/regional/national/international regulations.
Classification system:
NFPA ratings (scale 0 – 4)
2
1
0
Health = 2
Fire = 1
Reactivity = 0
HMIS-ratings (scale 0 – 4)
HEALTH
FIRE
REACTIVITY
*2
1
0
Health = *2
Fire = 1
Reactivity = 0
Other hazards
Results of PBT and vPvB assessment
PBT:Not applicable.
(Contd. on page 3)
US

Page 3/12
Safety Data Sheet
acc. to OSHA HCS
Printing date 10/19/2021 Reviewed on 10/19/2021
Trade name: TCC410 Resin
(Contd. of page 2)
53.0
vPvB:Not applicable.
* 3 Composition/information on ingredients
Chemical characterization: Mixtures
Description:Mixture of the substances listed below with nonhazardous additions.
Dangerous components:
CAS: 25068-38-6
NLP: 500-033-5
Reaction Product of Bisphenol A and Epichlorohydrin 20-50%
CAS: 68609-97-2
EINECS: 271-846-8
oxirane, mono[(C12-14-alkyloxy)methyl] derivs
Alkyl C12-C14 Glycidyl Ether 5-<10% CAS: 41638-13-5 Polyglycol epichlorohydrin polymer 1-5% CAS: 14808-60-7 EINECS: 238-878-4 Quartz (SiO2) 0.1-1% * 4 First-aid measures Description of first aid measures General information:Immediately remove any clothing soiled by the product. After inhalation: Supply fresh air and to be sure call for a doctor. In case of unconsciousness place patient stably in side position for transportation. After skin contact:Immediately wash with water and soap and rinse thoroughly. After eye contact: Rinse opened eye for several minutes under running water. If symptoms persist, consult a doctor. After swallowing:If symptoms persist consult doctor. Information for doctor: Most important symptoms and effects, both acute and delayedNo further relevant information available. Indication of any immediate medical attention and special treatment needed No further relevant information available. * 5 Fire-fighting measures Extinguishing media Suitable extinguishing agents:Use fire fighting measures that suit the environment. Special hazards arising from the substance or mixtureNo further relevant information available. Advice for firefighters Protective equipment:Wear self-contained respiratory protective device. (Contd. on page 4) US Page 4/12 Safety Data Sheet acc. to OSHA HCS Printing date 10/19/2021 Reviewed on 10/19/2021 Trade name: TCC410 Resin (Contd. of page 3) 53.0 Additional information Dispose of fire debris and contaminated fire fighting water in accordance with official regulations. * 6 Accidental release measures Personal precautions, protective equipment and emergency proceduresNot required. Environmental precautions: Dilute with plenty of water. Do not allow to enter sewers/ surface or ground water. Methods and material for containment and cleaning up: Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders, sawdust). Dispose contaminated material as waste according to item 13. Ensure adequate ventilation. Reference to other sections See Section 7 for information on safe handling. See Section 8 for information on personal protection equipment. See Section 13 for disposal information. Protective Action Criteria for Chemicals PAC-1: 25068-38-6 Reaction Product of Bisphenol A and Epichlorohydrin 90 mg/m 14808-60-7 Quartz (SiO2) 0.075 mg/m PAC-2: 25068-38-6 Reaction Product of Bisphenol A and Epichlorohydrin 990 mg/m 14808-60-7 Quartz (SiO2) 33 mg/m PAC-3: 25068-38-6 Reaction Product of Bisphenol A and Epichlorohydrin 5,900 mg/m 14808-60-7 Quartz (SiO2) 200 mg/m * 7 Handling and storage Handling: Precautions for safe handling Ensure good ventilation/exhaustion at the workplace. Open and handle receptacle with care. Prevent formation of aerosols. Information about protection against explosions and fires:Keep respiratory protective device available. Conditions for safe storage, including any incompatibilities Storage: Requirements to be met by storerooms and receptacles:No special requirements. Information about storage in one common storage facility:Not required. Further information about storage conditions:Keep receptacle tightly sealed. (Contd. on page 5) US Page 5/12 Safety Data Sheet acc. to OSHA HCS Printing date 10/19/2021 Reviewed on 10/19/2021 Trade name: TCC410 Resin (Contd. of page 4) 53.0 Specific end use(s)No further relevant information available. * 8 Exposure controls/personal protection Additional information about design of technical systems:No further data; see item 7. Control parameters Components with limit values that require monitoring at the workplace: The product does not contain any relevant quantities of materials with critical values that have to be monitored at the workplace. Additional information:The lists that were valid during the creation were used as basis. Exposure controls Personal protective equipment: General protective and hygienic measures: Keep away from foodstuffs, beverages and feed. Immediately remove all soiled and contaminated clothing. Wash hands before breaks and at the end of work. Store protective clothing separately. Avoid contact with the eyes and skin. Breathing equipment: In case of brief exposure or low pollution use respiratory filter device. In case of intensive or longer exposure use respiratory protective device that is independent of circulating air. Protection of hands: Protective gloves The glove material has to be impermeable and resistant to the product/ the substance/ the preparation. Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/ the chemical mixture. Selection of the glove material on consideration of the penetration times, rates of diffusion and the degradation Material of gloves The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. As the product is a preparation of several substances, the resistance of the glove material can not be calculated in advance and has therefore to be checked prior to the application. Penetration time of glove material The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed. (Contd. on page 6) US Page 6/12 Safety Data Sheet acc. to OSHA HCS Printing date 10/19/2021 Reviewed on 10/19/2021 Trade name: TCC410 Resin (Contd. of page 5) 53.0 Eye protection: Tightly sealed goggles * 9 Physical and chemical properties Information on basic physical and chemical properties General Information Appearance: Form: Viscous Color: Silver grey Odor: Amine-like Odor threshold: Not determined. pH-value: Not determined. Change in condition Melting point/Melting range:Undetermined. Boiling point/Boiling range:2,500 C (36.500 F) Flash point: 150 C (302 F) Flammability (solid, gaseous):Not applicable. Ignition temperature: 400 C (752 F) Decomposition temperature: Not determined. Auto igniting: Product is not selfigniting. Danger of explosion: Product does not present an explosion hazard. Explosion limits: Lower: Not determined. Upper: Not determined. Vapor pressure: Not determined. Density at 20 C (68 F): 1.95 g/cm (16.27 lbs/gal) Relative density Not determined. Vapor density Not determined. Evaporation rate Not determined. Solubility in / Miscibility with Water: Fully miscible. Partition coefficient (n-octanol/water):Not determined. Viscosity: Dynamic: Not determined. (Contd. on page 7) US Page 7/12 Safety Data Sheet acc. to OSHA HCS Printing date 10/19/2021 Reviewed on 10/19/2021 Trade name: TCC410 Resin (Contd. of page 6) 53.0 Kinematic: Not determined. Solvent content: Organic solvents: 0.4 % VOC content: 0.38 % 7.4 g/l / 0.06 lb/gal Solids content: 61.5 % Other information No further relevant information available. * 10 Stability and reactivity ReactivityNo further relevant information available. Chemical stability Thermal decomposition / conditions to be avoided:No decomposition if used according to specifications. Possibility of hazardous reactionsNo dangerous reactions known. Conditions to avoidNo further relevant information available. Incompatible materials:No further relevant information available. Hazardous decomposition products:Carbon monoxide and carbon dioxide * 11 Toxicological information Information on toxicological effects Acute toxicity: Primary irritant effect: on the skin:Irritant to skin and mucous membranes. on the eye:Irritating effect. Sensitization:Sensitization possible through skin contact. Additional toxicological information: The product shows the following dangers according to internally approved calculation methods for preparations: Irritant Carcinogenic categories IARC (International Agency for Research on Cancer) 14807-96-6 Talc (Mg3H2(SiO3)4) 3 14808-60-7 Quartz (SiO2) 1 NTP (National Toxicology Program) 14808-60-7 Quartz (SiO2) K OSHA-Ca (Occupational Safety & Health Administration) None of the ingredients is listed. US (Contd. on page 8) Page 8/12 Safety Data Sheet acc. to OSHA HCS Printing date 10/19/2021 Reviewed on 10/19/2021 Trade name: TCC410 Resin (Contd. of page 7) 53.0 * 12 Ecological information Toxicity Aquatic toxicity:No further relevant information available. Persistence and degradabilityNo further relevant information available. Behavior in environmental systems: Bioaccumulative potentialNo further relevant information available. Mobility in soilNo further relevant information available. Additional ecological information: General notes: Water hazard class 2 (Self-assessment): hazardous for water Do not allow product to reach ground water, water course or sewage system. Danger to drinking water if even small quantities leak into the ground. Results of PBT and vPvB assessment PBT:Not applicable. vPvB:Not applicable. Other adverse effectsNo further relevant information available. * 13 Disposal considerations Waste treatment methods Recommendation: Must not be disposed of together with household garbage. Do not allow product to reach sewage system. Uncleaned packagings: Recommendation:Disposal must be made according to official regulations. Recommended cleansing agent:Water, if necessary with cleansing agents. * 14 Transport information UN-Number DOT not regulated IMDG, IATA UN3082 UN proper shipping name DOT not regulated IMDG ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S. (Epoxy Resin), MARINE POLLUTANT IATA ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S. (Epoxy Resin) (Contd. on page 9) US Page 9/12 Safety Data Sheet acc. to OSHA HCS Printing date 10/19/2021 Reviewed on 10/19/2021 Trade name: TCC410 Resin (Contd. of page 8) 53.0 Transport hazard class(es) DOT Class not regulated IMDG, IATA Class 9 Miscellaneous dangerous substances and articles Label 9 Packing group DOT not regulated IMDG, IATA III Environmental hazards: Marine pollutant: Yes Symbol (fish and tree) Special marking (IATA): Symbol (fish and tree) Special precautions for user Warning: Miscellaneous dangerous substances and articles EMS Number: F-A,S-F Stowage Category A Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code Not applicable. UN "Model Regulation": UN 3082 ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S. (EPOXY RESIN), 9, III * 15 Regulatory information Safety, health and environmental regulations/legislation specific for the substance or mixture Sara Section 355 (extremely hazardous substances): None of the ingredients is listed. Section 313 (Specific toxic chemical listings): 7429-90-5 aluminum powder (stabilised) TSCA (Toxic Substances Control Act): All components have the value ACTIVE. Chemicals regulated by TSCA Section 12(b) None of the ingredients is listed. (Contd. on page 10) US Page 10/12 Safety Data Sheet acc. to OSHA HCS Printing date 10/19/2021 Reviewed on 10/19/2021 Trade name: TCC410 Resin (Contd. of page 9) 53.0 Chemical regulated by TSCA 5(a)(2)rule: None of the ingredients is listed. Hazardous Air Pollutants 98-82-8 cumene Proposition 65 Chemicals known to cause cancer: 1317-65-3 Calcium Carbonate 14808-60-7 Quartz (SiO2) 14808-60-7 Quartz (SiO2) 98-82-8 cumene Chemicals known to cause reproductive toxicity for females: None of the ingredients is listed. Chemicals known to cause reproductive toxicity for males: None of the ingredients is listed. Chemicals known to cause developmental toxicity: None of the ingredients is listed. Carcinogenic categories TLV (Threshold Limit Value) 14808-60-7 Quartz (SiO2) A2 NIOSH-Ca (National Institute for Occupational Safety and Health) 14808-60-7 Quartz (SiO2) Listed in CWC Regulations None of the ingredients is listed. GHS label elementsThe product is classified and labeled according to the Globally Harmonized System (GHS). Hazard pictograms GHS07GHS08 Signal wordDanger Hazard-determining components of labeling: Reaction Product of Bisphenol A and Epichlorohydrin Quartz (SiO2) oxirane, mono[(C12-14-alkyloxy)methyl] derivs Alkyl C12-C14 Glycidyl Ether Polyglycol epichlorohydrin polymer (Contd. on page 11) US Page 11/12 Safety Data Sheet acc. to OSHA HCS Printing date 10/19/2021 Reviewed on 10/19/2021 Trade name: TCC410 Resin (Contd. of page 10) 53.0 Hazard statements Causes skin irritation. Causes serious eye irritation. May cause an allergic skin reaction. May cause cancer. Precautionary statements Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Avoid breathing dust/fume/gas/mist/vapors/spray Wash thoroughly after handling. Contaminated work clothing must not be allowed out of the workplace. Wear protective gloves/protective clothing/eye protection/face protection. If on skin: Wash with plenty of water. If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. IF exposed or concerned: Get medical advice/attention. Specific treatment (see on this label). Take off contaminated clothing and wash it before reuse. If skin irritation or rash occurs: Get medical advice/attention. If eye irritation persists: Get medical advice/attention. Wash contaminated clothing before reuse. Store locked up. Dispose of contents/container in accordance with local/regional/national/international regulations. National regulations: Information about limitation of use: Workers are not allowed to be exposed to the hazardous carcinogenic materials contained in this preparation. Exceptions can be made by the authorities in certain cases. Chemical safety assessment:A Chemical Safety Assessment has not been carried out. 16 Other information This information is based on our present knowledge. However, this shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship. Contact: Date of preparation / last revision10/19/2021 / 4 Abbreviations and acronyms: IMDG: International Maritime Code for Dangerous Goods DOT: US Department of Transportation IATA: International Air Transport Association EINECS: European Inventory of Existing Commercial Chemical Substances ELINCS: European List of Notified Chemical Substances CAS: Chemical Abstracts Service (division of the American Chemical Society) NFPA: National Fire Protection Association (USA) HMIS: Hazardous Materials Identification System (USA) VOC: Volatile Organic Compounds (USA, EU) PBT: Persistent, Bioaccumulative and Toxic vPvB: very Persistent and very Bioaccumulative NIOSH: National Institute for Occupational Safety (Contd. on page 12) US Page 12/12 Safety Data Sheet acc. to OSHA HCS Printing date 10/19/2021 Reviewed on 10/19/2021 Trade name: TCC410 Resin (Contd. of page 11) 53.0 OSHA: Occupational Safety & Health TLV: Threshold Limit Value PEL: Permissible Exposure Limit REL: Recommended Exposure Limit Skin Irrit. 2: Skin corrosion/irritation Category 2 Eye Irrit. 2A: Serious eye damage/eye irritation Category 2A Skin Sens. 1: Skin sensitisation Category 1 Carc. 1A: Carcinogenicity Category 1A * Data compared to the previous version altered. US