37WA138_TDS.pdf
RELEASES COMPOUNDS POLISHES SEALERS
TR INDUSTRIES
11022 Vulcan Street
South Gate, CA 90280-0893
Phone 562 -923-0838 Fax 562-861-3475
www.trmoldrelease.com info@trmoldrelease.com
TR-905
MOLD PREP CLEANER
SOLVENT
DESCRIPTION:
A proprietary solvent mixture to remove wax, oils and other surface contaminants from reinforced polyester tooling and
other hard surface molds
PRODUCT FEATURES:
Fast evaporation with excellent cleaning ability
Removes compound residue after polishing
Effective on polyester, epoxy and metal tooling
Does not reduce gloss on mold surface
Promotes bonding of sealer/release to mold
Aids in moisture removal after water cleaning
USES:
Recommended for preparation and cleaning of mold surface prior to application of TR-900 Series MULT-PULL Semi-
Permanent Releases or the TR-910 Sealer.
APPLICATION:
Apply TR-905 solvent to mold surface using a clean all cotton (no synthetic blends) cloth working an area sufficient to
stay wet dissolving previously used wax or similar releases. While still wet or dissolved in mold cleaner, wipe dry with
another clean dry cloth, turning and changing cloth frequently to facilitate pick-up. Repeat as necessary until mold is
thoroughly cleaned and dry. Some molds may require use of a light buffing compound for previously used releases or
sealers. The mold prep cleaner should be used after water washing to remove buffing compound residue remaining on
the mold surface. The mold surface should always be wiped dry prior to use of the TR-900 series releases or TR-910
mold sealer.
PHYSICAL PROPERTIES:
Solvent Carrier: Blended aromatic/ ketone solvent
Specific Gravity: 0.83
Wt./Gal: 6.91lbs./gal
Flash Point: 34 F (0.8 C)
Evaporation Rate: >1 (butyl acetate = 1)
STORAGE AND PRECAUTIONS:
TR-905 mold prep cleaner contains flammable solvents. Keep aw ay from spark, open flame or other sources of
ignition. Close container after use and keep stored in cool area. Avoid prolonged exposure to breathing and contact
with skin. Use only with adequate ventilation. Use respirators or fresh air masks in confined areas.
PACKAGING:
Available in gallon 4×1/cases, 5 gallon pail and 55 gallon drum. Please contact your local TR distributor or call direct.
FOR INDUSTRIAL USE ONLY
The information contained herein is based on tests considered to be reliable and accurate. Because of the wide variance of associated materials
and conditions, no warranty is expressed or implied. Each user is encouraged to prepare a test part for their particular application .
37WA140_TDS.pdf
RELEASES COMPOUNDS POLISHES SEALERS
TR INDUSTRIES
11022 Vulcan Street
South Gate, CA 90280-0893
Phone 562-923-0838 Fax 562-861-3475
www.trmoldrelease.com info@trmoldrelease.com
TR-900
MULTI-PULL
LIQUID SEMI-PERMANENT RELEASE
DESCRIPTION:
TR-900 is a high temp semi-permanent release coating which dries rapidly under atmospheric conditions, bonding an
ultra thin clear release film to the mold surface. Exceptional multiple releases per application for various polyester
molding processes and other resin fiberglass fabrication.
PRODUCT FEATURES:
Excellent hi-temp properties (Thermally Stable 750 F )(400 C)
Multiple release per application
Rapid cure time speeds production cycle
No pre-release or transfer
Wipes to high gloss finish
Easily recoats without build-up
SUGGESTED USES: An ef fective multiple release agent for the FRP and related molders
Open mold hand or spray lay-up
Compression molding
Injection molded parts
Vacuum bag
Resin transfer molding (RTM)
APPLICATION: Always use and apply with a clean, lint-free 100% cotton white cloth (no synthetic blends). Clean
mold surface thoroughly of all previous release agents and sealers using the TR-905 mold prep solvent. Surface
should be completely dry and free of any contaminates. Apply TR-900 by wiping a thin wet coat onto a small area
(approx. 3 x 3 ft.) of the mold surface starting at an end point of the mold. (Do not apply heavily or excessively
wet). While the release film is still wet, wipe gently with another clean dry cotton cloth, turning and changing
cloths as required for proper drying. Avoid excessive hard rubbing or wiping of the treated surface which ensures a
more uniform and effective film deposit. Apply each application overlapping the previous small area until the entire
mold surface is complete. Repeat this for 3-4 coats to the entire mold surface allowing minimum 15 minutes
between coats and 30 minutes after final coat. Maximum results obtained if mold is allowed to stand overnight
before first use. A touch-up coat is recommended for the first 2-3 initial releases to maximize mold conditioning
and durability. When spraying, use a dry air source or airless spray, applying in a thin continuous smooth film,
avoiding excess flooding or runs. Wipe with a clean dry cotton cloth as noted in wipe application.
NOTE: Recommend use of TR-910 SEALER on new or green or repaired molds, more porous or rough mold
surfaces for maximum performance of the TR-900 RELEASE.
PHYSICAL PROPERTIES:
Solvent Carrier: Blend of aliphatic and aromatic naphtha solvent
Specific Gravity: 0.87
Wt./Gal.: 7.25 lbs./Gal.
Coverage: Approx. 1200 Sq. Ft./Gal.
Cure Time: Approx. 15 min. at Room Temp. (75 F) between coats and 30min after final coat
Appearance: Clear thin liquid with characteristic odor.
Cure Method: Chemical reaction with atmospheric moistur e following solvent evaporation
STORAGE AND PRECAUTIONS:
TR-900 contains flammable solvents. Keep away from spark, open flame or other sources of ignition. Store in a cool
dry place and keep in original unopened container. Product will react with atmospheric moisture and container should
be kept tightly closed when not in use. Avoid creating static discharge, do not use microfiber cloth.
PACKAGING:
Available in gallon 4×1 case, 5 gallon pail and 55 gallon drum. Please c ontact your local TR distributor or call direct.
FOR INDUSTRIAL USE ONLY
The information contained herein is based on tests considered to be reliable and accurate. Because of the wide variance of associated materials
and conditions, no warranty is expressed or implied. Each user is encouraged to prepare a test part for their particular application.
37WA138C_TDS.pdf
RELEASES COMPOUNDS POLISHES SEALERS
TR INDUSTRIES
11022 Vulcan Street
South Gate, CA 90280-0893
Phone 562- 923-0838 Fax 562- 861-3475
www.trmoldrelease.com info@trmoldrelease.com
TR-920
MULTI-PULL
LIQUID SEMI- PERMANENT RELEASE
DESCRIPTION:
TR-920 is a high-temp multiple capability semi-permanent release coating which cures under atmospheric conditions,
bonding a durable thin clear release coating to the mold surface. Multiple releases per application for polyester, epoxy,
polymides, BMC, SMC, and various other advanced resins in fiberglass or graphite composite molding processes.
PRODUCT FEATURES:
Excellent hi-temp properties (Thermally Stable to 900 F/482 C)
Multiple releases per application
Ease of application and fast cure time
No pre-release or transfer
Wipes to a gloss finish
Easily recoats without build-up
SUGGESTED USES:
An effective multiple release agent for the FRP and related molders.
Open mold hand or spray lay-up
Compression molding
Injection molded parts
Vacuum bag
Resin transfer molding (RTM)
APPLICATION: Always use and apply with a clean, lint-free all cotton cloth (no synthetic blends). Clean mold surface
thoroughly of all previous release agents and sealers using the TR-905 mold prep solvent. Mold surface should be completely dry and free of any contaminates. Apply TR-920 by wiping a thin wet coat onto a small area (approx. 3 x 3
ft.) of the mold surface starting at an end point of the mold. While the release film is still wet, wipe gently with another clean, dry, cotton cloth, turning and changing cloths as required for proper drying. Avoid excessive hard rubbing or
wiping of the treated surface, which ensures a more uniform and effective film deposit. Apply each subsequent release coat overlapping the previous small area until complete mold surface is covered. Repeat this for 3-4 coats to the entire
mold waiting 15-20 minutes between coats. Cure time of the final release film at room temperature (75 F/24 C ) is
approximately 30 minutes. Additional touch-up coat is recommended for the first 2-3 initial releases to maximize mold
conditioning and durability. When spraying, use a dry air source or airless spray, applying in a thin continuous smooth
film, avoiding excess flooding or runs. Polish wipe with a clean, dry, cotton cloth as noted in wipe application.
NOTE: Recommend use of TR-910 SEALER on new or repaired molds, more porous or rough mold surfaces for
maximum performance of the 900 SERIES MULT-PULL RELEASES.
PHYSICAL PROPERTIES:
Solvent Carrier: Blend of aliphatic and arom atic naphtha solvent
Specific Gravity: 0.875
Wt./Gal.: 7.3 lbs./Gal.
Shelf Life: 1 year from date of manufacture
Coverage: Approx. 1200 Sq. Ft./Gal.
Cure Time: Approx. 15-20 min. at Room Temp. (75 F/24 C)
Appearance: Clear thin liquid with characteristic odor.
Cure Method: Chemical reaction with atmospheric moisture following solvent evaporation.
STORAGE AND PRECAUTIONS:
TR-920 contains flammable solvents. Keep away from spark, open flame or other sources of ignition. Store in a cool
dry place and keep in original unopened container. Product will react with atmospheric moisture and container
should be kept tightly closed when not in use. Avoid creating static discharge, do not use microfiber cloth.
PACKAGING:
Available in gallon 4×1 case, 5 gallon pail and 55 gallon drum. Please c ontact your local TR distributor or call direct.
FOR INDUSTRIAL USE ONLY
The information contained herein is based on tests considered to be reliable and accurate. Because of the wide variance of associated materials
and conditions, no warranty is expressed or implied. Each user is encouraged to prepare a test part for their particular application.
37WA138B_TDS.pdf
RELEASES COMPOUNDS POLISHES SEALERS
TR INDUSTRIES
11022 Vulcan Street
South Gate, CA 90280-0893
Phone 562- 923-0838 Fax 562- 861-3475
www.trmoldrelease.com info@trmoldrelease.com
TR-920
MULTI-PULL
LIQUID SEMI- PERMANENT RELEASE
DESCRIPTION:
TR-920 is a high-temp multiple capability semi-permanent release coating which cures under atmospheric conditions,
bonding a durable thin clear release coating to the mold surface. Multiple releases per application for polyester, epoxy,
polymides, BMC, SMC, and various other advanced resins in fiberglass or graphite composite molding processes.
PRODUCT FEATURES:
Excellent hi-temp properties (Thermally Stable to 900 F/482 C)
Multiple releases per application
Ease of application and fast cure time
No pre-release or transfer
Wipes to a gloss finish
Easily recoats without build-up
SUGGESTED USES:
An effective multiple release agent for the FRP and related molders.
Open mold hand or spray lay-up
Compression molding
Injection molded parts
Vacuum bag
Resin transfer molding (RTM)
APPLICATION: Always use and apply with a clean, lint-free all cotton cloth (no synthetic blends). Clean mold surface
thoroughly of all previous release agents and sealers using the TR-905 mold prep solvent. Mold surface should be completely dry and free of any contaminates. Apply TR-920 by wiping a thin wet coat onto a small area (approx. 3 x 3
ft.) of the mold surface starting at an end point of the mold. While the release film is still wet, wipe gently with another clean, dry, cotton cloth, turning and changing cloths as required for proper drying. Avoid excessive hard rubbing or
wiping of the treated surface, which ensures a more uniform and effective film deposit. Apply each subsequent release coat overlapping the previous small area until complete mold surface is covered. Repeat this for 3-4 coats to the entire
mold waiting 15-20 minutes between coats. Cure time of the final release film at room temperature (75 F/24 C ) is
approximately 30 minutes. Additional touch-up coat is recommended for the first 2-3 initial releases to maximize mold
conditioning and durability. When spraying, use a dry air source or airless spray, applying in a thin continuous smooth
film, avoiding excess flooding or runs. Polish wipe with a clean, dry, cotton cloth as noted in wipe application.
NOTE: Recommend use of TR-910 SEALER on new or repaired molds, more porous or rough mold surfaces for
maximum performance of the 900 SERIES MULT-PULL RELEASES.
PHYSICAL PROPERTIES:
Solvent Carrier: Blend of aliphatic and arom atic naphtha solvent
Specific Gravity: 0.875
Wt./Gal.: 7.3 lbs./Gal.
Shelf Life: 1 year from date of manufacture
Coverage: Approx. 1200 Sq. Ft./Gal.
Cure Time: Approx. 15-20 min. at Room Temp. (75 F/24 C)
Appearance: Clear thin liquid with characteristic odor.
Cure Method: Chemical reaction with atmospheric moisture following solvent evaporation.
STORAGE AND PRECAUTIONS:
TR-920 contains flammable solvents. Keep away from spark, open flame or other sources of ignition. Store in a cool
dry place and keep in original unopened container. Product will react with atmospheric moisture and container
should be kept tightly closed when not in use. Avoid creating static discharge, do not use microfiber cloth.
PACKAGING:
Available in gallon 4×1 case, 5 gallon pail and 55 gallon drum. Please c ontact your local TR distributor or call direct.
FOR INDUSTRIAL USE ONLY
The information contained herein is based on tests considered to be reliable and accurate. Because of the wide variance of associated materials
and conditions, no warranty is expressed or implied. Each user is encouraged to prepare a test part for their particular application.
37WA138A_TDS.pdf
37WA137_TDS.pdf
RELEASES COMPOUNDS POLISHES SEALERS
TR INDUSTRIES
11022 Vulcan Street
South Gate, CA 90280-0893
Phone 562- 923-0838 Fax 562- 861-3475
www.trmoldrelease.com info@trmoldrelease.com
TR-930
MULTI-PULL
LIQUID SEMI- PERMANENT RELEASE
DESCRIPTION:
TR-930 is a high-temp multiple capability semi-permanent release coating which cures under atmospheric condition,
bonding a durable thin, clear release coating to the mold surface. Multiple releases per application for polyester, epoxy,
polyimides, BMC, SMC, and various other advanced resins in fiberglass or graphite composite molding processes,
thermoplastic rotational and rubber molding.
PRODUCT FEATURES:
Excellent hi-temp properties (Thermally Stable to 750 F)(400 C)
Multiple release per application
Ease of application and fast cure time
No pre-release or transfer
Wipes to high gloss finish.
Easily recoats without build-up
SUGGESTED USES: An effective multiple release agent for the FRP and related molders.
Open mold hand or spray lay-up
Compression molding
Injection molded parts
Vacuum bag
Resin transfer molding (RTM)
APPLICATION: HIGH GLOSS POLYESTER
Always use and apply with a clean, lint free all cotton cloth (no synthetic blends). Clean mold surface thoroughly of all
previous release agents and sealers using TR -905 mold prep solvent. Surface should be completely dry and free of
any contaminates. Apply TR-930 by wiping a thin wet coat onto a small area (approx. 3×3 ft.) of the mold surface
starting at an end point of the mold. While the release film is still wet, wipe gently with another clean dry cotton cloth, turning and changing cloths as required for proper drying. Avoid excessive hard rubbing or wiping of the treated surface which ensures a more uniform and effective film deposit. Apply each application overlapping the previous small area until the entire mold surface is complete. Repeat this for 3 4 coats to the entire mold surface. Cure time of
the release film at room temperature (75 F) is approximately 10-15 minutes between coats allowing 20-30min after
final coat before u sing mold. A touch-up coat is recommended for the first 2-3 initial releases to maximize mold
conditioning and durability. When spraying, use a dry air source or airless spray, applying in a thin continuous smooth film, avoiding excess flooding or runs. Wipe with a clean dry cotton cloth as noted in wipe application.
NON-GLOSS OR EPOXY APPLICATIONS: Apply 3-4 thin wet coats allowing solvents to flash. Wait additional 10-15
minutes after solvent evaporation before applying subsequent coats. Surface should be dry and not tacky.
PHYSICAL PROPERTIES:
Solvent Carrier: Blend of Aliphatic and Aromatic Naphthas
Specific Gravity: 0.76
Wt./Gal.: 6.3 lbs./Gal.
Coverage: Approx. 1200 Sq. Ft./Gal.
Cure Time: Approx. 10-20 min. at room temp. (75 F) or 5 min. at 250 F
Appearance: Clear thin liquid with characteristic odor.
Cure Method: Chemical reaction with atmospheric moisture following solvent evaporation.
NOTE: Recommend use of the TR -910 SEALER on new or green and repaired molds or for more porous or rough mold
surfaces and maximum performance of the TR -930 RELEASE.
STORAGE AND PRECAUTIONS: TR- 930 contains flammable solvents. Keep away from spark, open flame or other
sources of ignition. Store in a cool dry place and keep in original unopened container. Product will react with atmospheric
moisture and container should be kept tightly closed when not in use. Avoid creating static discharge, do not use microfiber
cloth.
PACKAGING:
Available in gallon 4×1 case, 5 gallon pail and 55 gallon drum. Please contact your local TR distributor or call direct.
FOR INDUSTRIAL USE ONLY
The information contained herein is based on tests considered to be reliable and ac curate. Because of the wide variance of associated materials
and conditions, however, no warranty is expressed or implied. Each user is encouraged to prepare a test part for his particular application.
37WA137CLB_TDS.pdf
RELEASES COMPOUNDS POLISHES SEALERS
TR INDUSTRIES
11022 Vulcan Street
South Gate, CA 90280-0893
Phone 562- 923-0838 Fax 562- 861-3475
www.trmoldrelease.com info@trmoldrelease.com
TR-930
MULTI-PULL
LIQUID SEMI- PERMANENT RELEASE
DESCRIPTION:
TR-930 is a high-temp multiple capability semi-permanent release coating which cures under atmospheric condition,
bonding a durable thin, clear release coating to the mold surface. Multiple releases per application for polyester, epoxy,
polyimides, BMC, SMC, and various other advanced resins in fiberglass or graphite composite molding processes,
thermoplastic rotational and rubber molding.
PRODUCT FEATURES:
Excellent hi-temp properties (Thermally Stable to 750 F)(400 C)
Multiple release per application
Ease of application and fast cure time
No pre-release or transfer
Wipes to high gloss finish.
Easily recoats without build-up
SUGGESTED USES: An effective multiple release agent for the FRP and related molders.
Open mold hand or spray lay-up
Compression molding
Injection molded parts
Vacuum bag
Resin transfer molding (RTM)
APPLICATION: HIGH GLOSS POLYESTER
Always use and apply with a clean, lint free all cotton cloth (no synthetic blends). Clean mold surface thoroughly of all
previous release agents and sealers using TR -905 mold prep solvent. Surface should be completely dry and free of
any contaminates. Apply TR-930 by wiping a thin wet coat onto a small area (approx. 3×3 ft.) of the mold surface
starting at an end point of the mold. While the release film is still wet, wipe gently with another clean dry cotton cloth, turning and changing cloths as required for proper drying. Avoid excessive hard rubbing or wiping of the treated surface which ensures a more uniform and effective film deposit. Apply each application overlapping the previous small area until the entire mold surface is complete. Repeat this for 3 4 coats to the entire mold surface. Cure time of
the release film at room temperature (75 F) is approximately 10-15 minutes between coats allowing 20-30min after
final coat before u sing mold. A touch-up coat is recommended for the first 2-3 initial releases to maximize mold
conditioning and durability. When spraying, use a dry air source or airless spray, applying in a thin continuous smooth film, avoiding excess flooding or runs. Wipe with a clean dry cotton cloth as noted in wipe application.
NON-GLOSS OR EPOXY APPLICATIONS: Apply 3-4 thin wet coats allowing solvents to flash. Wait additional 10-15
minutes after solvent evaporation before applying subsequent coats. Surface should be dry and not tacky.
PHYSICAL PROPERTIES:
Solvent Carrier: Blend of Aliphatic and Aromatic Naphthas
Specific Gravity: 0.76
Wt./Gal.: 6.3 lbs./Gal.
Coverage: Approx. 1200 Sq. Ft./Gal.
Cure Time: Approx. 10-20 min. at room temp. (75 F) or 5 min. at 250 F
Appearance: Clear thin liquid with characteristic odor.
Cure Method: Chemical reaction with atmospheric moisture following solvent evaporation.
NOTE: Recommend use of the TR -910 SEALER on new or green and repaired molds or for more porous or rough mold
surfaces and maximum performance of the TR -930 RELEASE.
STORAGE AND PRECAUTIONS: TR- 930 contains flammable solvents. Keep away from spark, open flame or other
sources of ignition. Store in a cool dry place and keep in original unopened container. Product will react with atmospheric
moisture and container should be kept tightly closed when not in use. Avoid creating static discharge, do not use microfiber
cloth.
PACKAGING:
Available in gallon 4×1 case, 5 gallon pail and 55 gallon drum. Please contact your local TR distributor or call direct.
FOR INDUSTRIAL USE ONLY
The information contained herein is based on tests considered to be reliable and ac curate. Because of the wide variance of associated materials
and conditions, however, no warranty is expressed or implied. Each user is encouraged to prepare a test part for his particular application.
37WA135B_TDS.pdf
RELEASES COMPOUNDS POLISHES SEALERS
TR INDUSTRIES
11022 Vulcan Street
South Gate, CA 90280-0893
Phone 562 -923-0838 Fax 562-861-3475
www.trmoldrelease.com info@trmoldrelease.com
TR-309
REGULAR COMPOUND
MEDIUM CUTTING PASTE
DESCRIPTION:
TR-309 is a medium coarse off-white paste compound developed specifically for light oxidation and sanding scratch
removal on polyester gel-coats.
PRODUCT FEATURES:
Fast cutting action for quick effective removal light sanding marks
Good initial gloss achieved on finished parts when sanding for minor defect repair
Remains moist while buffing with less spotting and drying
Restores gloss to lightly oxidized & weathered finishes
Contains no silicones or waxes
Economically priced
PHYSICAL PROPERTIES:
Specific Gravity: 1.23 (10.25lbs./Gal)
Viscosity: soft paste water/petroleum emulsion blend
Color: off-white
USES:
To provide good initial uniform gloss while removing sanding scratches (600g-800g), light oxidation and minor
surface imperfections on all gel coated finishes.
APPLICATION:
Apply TR-309 to gel-coated surface and spread evenly. Using a high speed electric variable speed buffer equipped
with all wool twisted buffing pad set buffer speed to 2,400 RPM for best results. Work in a 2 x 2 overlapping
surface area using medium pressure to keep surface moist to avoid drying out and burnishing. As polish begins to
dry gradually reduce buffing pressure to achieve a smooth uniform gloss appearance. Use a buffing spur to clean
pad frequently during use to remove excess compound build up.
NOTE:
For optimum results polish with TR-308 Fine Finish II to achieve a high gloss mirror like swirl free finish after using
TR-309 regular compound.
PACKAGING:
TR-309 is available in Gallon 4×1 case, 5gal pail or 55gal drum. Recommended to store in a cool dry place to
maintain one year shelf life stability.
FOR INDUSTRIAL USE ONLY
The information contained herein is based on tests considered to be reliable and accurate. Because of the wide variance of associated materials
and conditions, however no warranty is expressed or implied. Each user is encouraged to prepare a test part for their particular application.
37WA122_TDS.pdf
!”# $%&&$
‘ $( )”$&* + , – ,+.
(‘#& /0 -+ .- ,., 1 2″3 /0 -,0 -.45/
6667$%8’ 9%& &”:&7!’8 ; <#='>$%8′ 9%& &”:&7!’8
?@ABCDE
FGHIAF?@JKKJLME
HJNOJPEQRHPE@GHGSFGE
PGFT@JK?JRLUE
VWXYZ[ ] ^ _`ab c^d ef_f^]f g^]fb hi hae jkWlkmnk g^]f o^]pf c^d ^ib g_fib hq ^rpsf r_f^iit ]h_sfip] ph
efbarf ^ib uiuvf ]pwefif ^ib c^d ef_f^]f ga_bXao he ^rraua_^phix
K@RPOT?EIGS?O@GFUE
y^]f hq ^oo_r^phi z hif ]pfo r_f^ife{ef_f^]f
|^]p bew puf z uoehsfb oehbarphi rwr_f]
}ehsbf] ^ib u^ip^i] ~t~ t_h]] ^oof^e^irf
ydrf__fip qhe bfp^_fb he ihiX] b pwof uh_b ]aeq^rf
OFGFUE^ _`ab c^d ef_f^]f qhe a]f hi ^__ |W} phh_it ufp^_ ^ib hp~fe ~^eb ]aeq^rf uh_b]x
EE ofi uh_b ~^ib he ]oe^w _^w ao
EE ^eg_f hp~fe p~r r^]pit ^oo_r^phi]
WV ^ib rhuoef]]hi uh_bit
jheeh]hi z p^i ] ooit
K FJTSHEK@RKG@?JGFUE
ew Vuf EEkooehdu^pf uiapf] ^p |
ofrqr e^spw EEx xY _g]x{ ^_
V~feu^_ p^g_pw EEZ [ | X Y[[ | Y j X j
jh_he EE_t~p wf__hc p~i _`ab
j E x Y_g]x{t^_ Zt{_
SKKHJTS?JRLUE `ab uh_b ef_f^]f ] efrhuufibfb qhe a]f hi_w hi cf__ rhibphifb phh_itx nef^ Xi ifc he
efrhibphifb uh_b ]aeq^rf] qe]p cp~ he VWX [ZE f^_fe _^vf ^ib VWXZ[YEhe VWXZ[ }^]pf ^d Wf_f^]fx p^ep a]f hq
p~f _`ab c^d ^qpfe X bfXuh_bit he ef_f^]f] a]it o^]pf c^dxE
koo_w cp~ rhpphi r_hp~ coit aiqheu_w i rera_^e uhphix kqpfe ^__hcit bewit X ui ^ib oh_]~it cp~ rhpphi
r_hp~ ph ~t~ t_h]] qi]~ oehrffb cp~ oehbarphi rwr_fx y^r~ ^oo_r^phi he a]f hq p~f hifX]pfo r_f^ife ef_f^]f
efuhsf] ]pwefif ~^vf ^ib fdrf]] c^d qehu uh_b ]aeq^rfx Wfof^pfb a]f u^ip^i] t_h]] efpfiphi ^ib rhipegapf] ph
whae uh_b u^ipfi^irfx j^i ^_]h gf ]oe^wfb he gea]~fbx nea]~it iph uhef bfp^_fb he ihiX] b ]aeq^rf] ^ib p~fi
cofb uufb^pf_w c__ ~f_o r_f^i p~^p pwof hq ]aeq^rfx fp oh_]~it ba__fb he _hcfe t_h]] ^ef^] c__ ef]phef _a]pfe he
]~if ph p~f ^qqfrpfb ^ef^] ^ib fipef uh_b ]aeq^rfx
LR?GUEWf`aef] ^tp^phi gfqhef ^ib baeit a]f ph fi]aef ^bf`a^pf c^d q_u p~r if]] hi uh_bx }h_wf]pfe phh_it
a]f hi_w hi uh_b] qe]p rhibphifb cp~ ^ o^]pf c^d ^ib ef_f^]f hq ^ qfc o^ep]x E
F?R@SMGESLPEK@GTSO?JRLFUE |_^uu^g_f _`ab ]phef i ^ rhh_ bew o_^rf ^ib ffo i heti^_ aihofifb
rhip^ifex ffo ^c^w qehu ]o^e hofi q_^uf he hp~fe ]haerf] hq tiphixE
KST SMJLMUEVWXYZ[E] ^s^_^g_f i t^__hi ^ib t^__hi beau]x }_f^]f rhip^rp whae _hr^_ VW b]pegaphe he r^__ befrpxE
E
IR@EJLPOF?@JSHEOFGERLH E
(& <#='%8"$<'# !'#$"<#&9 (&%&<# <: ":&9 '# $&:$: !'#:<9&%&9 $' & %& <" & "#9 "!! %"$&7 &!" :& '= $(& 6<9& "%<"#!& '= "::'!<"$&9 8"$&%<" : "#9 !'#9<$<'#:* #' 6"%%"#$ <: &3 %&::&9 '% <8 <&97 "!( :&% <: &#!' %" &9 $' %& "%& " $&:$ "%$ ='% $(&<% "%$