by | Sep 27, 2025
RELEASES COMPOUNDS POLISHES SEALERS
TR INDUSTRIES
11022 Vulcan Street
South Gate, CA 90280-0893
Phone 562 -923-0838 Fax 562-861-3475
www.trmoldrelease.com info@trmoldrelease.com
TR-104
HI-TEMP MOLD RELEASE
DESCRIPTION:
An industry standard premium paste release for use in higher exothermic applications. Formulated using only the
highest quality refined carnauba wax, blended with other high temperature synthetic waxes and additives producing
the highest quality mold release wax for the composites market.
PRODUCT FEATURES:
Ease of application and removal may be allowed to stand before polishing
Provides hard film with superior heat and chemical properties
Polishes to high gloss without streaking
Reduced wax build-up and styrene accumulation
PHYSICAL PROPERTIES:
Dry Time: 5-10 minutes@ 72 F. Varies depending on working temperature
Wax Melting or Softening Point: 195 – 210 F (88 – 99 C)
Penetration Hardness: 1 at 25 C (carnauba wax)
Color: light blue tint (color coded for identification)
VOC Content: 4.84lbs./gal (580g/l)
USES:
As a release agent for composite molding on all FRP tooling, Formica, metal and other hard surface molds.
Open mold hand or spray lay up
Resin Transfer/injection (RTM) & (RIM)
Vacuum bag and compression molding
Polyester & epoxy resins
NOTE: Check suitability when heat curing or higher temperature molding above 215 F (102 C)
APPLICATION:
On new or reconditioned tooling, suggest use of our sealer glaze TR -301 or TR-910 semi-permanent sealer prior to
waxing for added release, gloss and mold life. Apply wax with sponge applicator in thin even circular motion to the mold
surface. Allow to haze dry (approx. 5-10 min) depending on ambient temperature and polish wipe to gloss finish with soft
cloth (do not use microfiber cloth). For new or reconditioned molds, apply a minimum of 6 coats of paste wax, waiting
approximately 30-60 minutes between applications for the wax to set & harden after the polish wipe. Best results are
obtained, if after application, mold is allowed to stand overnight and a subsequent final coat of wax release applied the
following day prior to gel coating. Follow with a coat of wax for the first 2-3 parts released. Then determine how many
parts can be effectively produced before re-waxing is required. This will vary depending on molding condition,
configuration, resin, mold cycles, effective cure of production gel coat and other factors.
STORAGE AND PRECAUTIONS:
Flammable solid, store in a cool dry place and keep in original unopened container. Keep away from spark, open flame
or other sources of ignition.
PACKAGING:
Available in 14oz (397g) cans and packaged in case quantity of 12 . Contact your local TR distributor or call direct.
FOR INDUSTRIAL USE ONLY
The information contained herein is based on tests considered to be reliable and accurate. Because of the wide variance of associated materials
and conditions, however no warranty is expressed or implied. Each user is encouraged to prepare a test part for their particular application.
by | Sep 27, 2025
RELEASES COMPOUNDS POLISHES SEALERS
TR INDUSTRIES
11022 Vulcan Street
South Gate, CA 90280-0893
Phone 562 -923-0838 Fax 562-861-3475
www.trmoldrelease.com info@trmoldrelease.com
TR-102
REGULAR MOLD RELEASE
DESCRIPTION:
A high production paste wax mold release with excellent breakdown characteristics for fast, even coverage. A firm
carnauba based mold release paste wax blended with other synthetic waxes for use in various thermo-set composite
molding applications.
PRODUCT FEATURES:
High carnauba wax content polishes to high gloss without streaking
Good heat and chemical resistance properties
Easy application and wipe off characteristics
Reduced wax build up and styrene accumulation
PHYSICAL PROPERTIES:
Dry Time: 5-10 minutes@ 72 F. Varies depending on working temperature
Specific Gravity: .80-.82 (approx. 6.75lbs./Gal)
Wax Melting or Softening Point: 185 – 200 F (85 – 93 C)
Color: Off-white
USES:
As a release agent for composite molding on all FRP tooling, metal and other hard surface molds.
Open mold hand or spray lay up
Resin Transfer/injection (RTM) & (RIM)
Vacuum bag and compression molding
Polyester & epoxy resins
NOTE: Check suitability when heat curing or higher temperature molding above 200 F (93 C)
APPLICATION:
On new or reconditioned tooling, suggest use of our sealer glaze TR -301 or TR-910 semi-permanent sealer prior to
waxing for added release, gloss and mold life. Apply wax with sponge applicator in thin even circular motion to the mold
surface. Allow to haze dry (approx. 5-10 min) depending on ambient temperature and polish wipe to gloss finish with soft
cloth (do not use microfiber cloth). For new or reconditioned molds, apply a minimum of 6 coats of paste wax, waiting
approximately 30-60 minutes between applications for the wax to set & harden after the polish wipe. Best results are
obtained, if after application, mold is allowed to stand overnight and a subsequent final coat of wax release applied the
following day prior to gel coating. Follow with a coat of wax for the first 2-3 parts released. Then determine how many
parts can be effectively produced before re-waxing is required. This will vary depending on molding condition,
configuration, resin, mold cycles, effective cure of production gel coat and other factors.
STORAGE AND PRECAUTIONS:
Flammable solid, store in a cool dry place and keep in original unopened container. Keep away from spark, open flame
or other sources of ignition.
PACKAGING:
Available in 14oz (397g) cans and packaged in case quantity of 12. Please contact your local TR distributor or call
direct.
FOR INDUSTRIAL USE ONLY
The information contained herein is based on tests considered to be reliable and accurate. Because of the wide variance of associated materials
and conditions, however no warranty is expressed or implied. Each user is encouraged to prepare a test part for their particular application.
by | Sep 27, 2025
RELEASES COMPOUNDS POLISHES SEALERS
TR INDUSTRIES
11022 Vulcan Street
South Gate, CA 90280-0893
Phone 562 -923-0838 Fax 562-861-3475
www.trmoldrelease.com info@trmoldrelease.com
TR-930HS
MULTI-PULL
LIQUID SEMI-PERMANENT RELEASE
DESCRIPTION:
TR-930HS is a high slip low odor fast curing multiple capability s emi-permanent mold release for use molding various
polymers (polyester, epoxy, polyamide, SMC, BMC, etc.). Excellent for difficult to release closed mold processes,
filament winding and non gel-coat polyester applications.
PRODUCT FEATURES:
High temperature properties up to 750 F (400 C)
High slip – multiple releases per application
Easy wipe on leave on or spray application
No pre-release or transfer
Durable high gloss coating
Easily recoats without build-up
USES:
Open mold hand or spray lay-up
Compression & Prepreg molding
Injection molded parts
Vacuum bag/RTM
Filament winding/Rotational Molding
APPLICATION:
Clean mold surface thoroughly of all previous sealers and release agents using TR-905 mold prep solvent. Light
abrasive compounding may be necessary to remove the various types of release agents or sealers previously used.
After compounding, first water wash and wipe dry to remove compound residue. Then completely clean the mold
surface with TR-905 mo ld prep solvent.
Apply a thin wet film to mold surfaces either by wipe or spray. Use an ALL-COTTON cloth when wiping to avoid possible
binders in other fabrics dissolving from solvent carriers. Use an airless spray unit or a dry air source when spraying
holding spray nozzle approximately 8-10 inches from mold surface. Start at one end of a mold working small areas or
sections to the other end ensuring a thin wet film is applied to entire mold surface. Secondary polish step is not required.
If desired gloss is reduced after application, lightly polish with 100% cotton cloth after final coat.
For initial break-in, apply 3-5 coats. Allow 5-10 minutes between each application and 10-15 minutes after final
application for solvent release and cure. Recoat for the first 2 -3 initial pulls or de- molding to aid full conditioning and
mold life. Recoat will vary depending upon mold design or materials. Apply again at first sign of release difficulties. Use
the TR-910 sealer if mold surface is porous, less smooth, or to provide improved initial release on new or green and
repaired molds.
PHYSICAL PROPERTIES:
Solvent Carrier: Blend of hydrocarbon naphtha
Specific Gravity: 0.725
Wt/Gal.: 6.04 lbs./Gal
Shelf Life: 1 year from date of manufacture
Cure Time: Approx. 5-10min. between coats and 10-15 min after final coat at room temp (75 F)
Appearance: Clear colorless with characteristic odor
Cure Method: Chemical reaction with atmospheric moisture following solvent evaporation
NOTE: Do not apply subsequent coats until complete solvent evaporation of prior coat.
STORAGE AND PRECAUTIONS:
TR-930HS contains flammable solvents. Keep away from spark, open flame or other sources of ignition. Store in a cool
dry place and keep in original un-opened container. Product will react with atmospheric moisture and container should
be kept tightly closed when not in use. Avoid creating static discharge, do not use microfiber cloth.
PACKAGING:
Available in gallon 4×1/cases, 5 gallon and 55 gallon drum. Please contact your local TR distributor or call direct.
FOR INDUSTRIAL USE ONLY
The information contained herein is based on tests considered to be reliable and accurate. Because of the wide variance of associated materials
and conditions, no warranty is expressed or implied. Each user is encouraged to prepare a test part for their particular application.
by | Sep 27, 2025
TR INDUSTRIES
11022 Vulcan Street
South Gate, CA 90280
Phone 562-923-0838 Fax 562-861-3475
RELEASES COMPOUNDS POLISHES
TR-111
SLURRY WAX RELEASE
FLANGES EDGES HATS
DESCRIPTION:
A soft white compounded wax based on refined petroleum waxes. Leaves no discoloration to molded
parts and contains no silicones.
PRODUCT FEATURES:
Easy spreading and wipe characteristics
Provides positive releases, remains soft and ease of removal
Effectively fills rough surfaces and is PVA compatible
Good thermal stability with reduced build up
USES:
For all mold flanges, edges and hats in cultured marble, onyx or granite production, FRP Tubs, showers,
spa fabrication, polymer concrete and general polyester molding applications. Any surface where gloss
or cosmetics is not a critical requirement for finished part. Sealer on porous substrates for prototypes and
mock-ups or in conjunction with PVA sprayed film.
APPLICATION:
Apply a minimum of two coats with brush or cloth allowing each coat to dry prior to applying additional
coats. This provides a base film for initial release. Apply again lightly after first part is pulled and then
subsequent coats as needed. Applications will vary dependent on surface conditions, molding cycle,
fabrication methods and general shop practices.
Available in gallon 4×1/cases, 5 gallon and 55 gallon drum. Please contact your local TR distributor or
call direct.
The information contained herein is based on tests considered to be reliable and accurate. Because of the wide variance of
associated materials and conditions, no warranty is expressed or implied. Each user is encouraged to prepare a test part for
their particular application.
by | Sep 27, 2025
Direction for Use
Recommended Procedure
This material is ready-to-use and requires no
dilution. Best application is achieved by applying a
thin coating using a wiping brushing or spraying. The
ideal application evenly wets the surface and dries to
a glossy layer of mold release. Over-application can
result in drips, runs or puddles of release can cause
part defects. If over applied, remove the excess with
an absorbent cloth prior to molding. Some customers
find a brush useful to even out the Stoner
M802
Mold Release on complicated molds. Best results
are obtained when release is applied shortly before
molding. Treated molds heated for more than 30
minutes at 250 F may require touch-up prior to molding.
Call for special instructions if parts will be painted,
glued or over-molded.
Storage and Handling
See SDS for complete instruction prior to use. Do not
use near ignition sources. Do not expose container
to heat or store at temperatures above 120 F. This
product is contains flammable solvents and proper
ventilation and static controls should be used. Proper
eye and skin protection should be used and some
operators prefer to wear an apron when applying
release or handling parts.
Packaging
Stoner
M802 Urethane Mold Release is available in:
5-gallon pails & 55-gallon drum
Part # M802 (Solvent Based)
Technical Assistance
Call: 800-227-5538 or 1 (717) 786-7355
Email: CustomerService@StonerMolding.com
Visit: StonerMolding.com
NO RISK GUARANTEE . Stoner Molding guarantees 100% satisfaction or your
money back. If you re ever dissatisfied with any Stoner Molding product, simply
return the unused portion for a full refund.
Product Description
Stoner
M802 Urethane Mold Release is specially
formulated as a release agent and anti-stick lubricant
for molded urethanes and similar materials. Provides
fast, easy part removal from molds and multiple part
releases per application. Improves molding efficiency
in many processes including injection, pour cast,
and extrusion molding. Economical a light coating
produces best results.
M802 Urethane Mold Release ADVANTAGES:
Saves time lets you remove urethane parts
from molds quickly and easily.
Fast evaporating for rapid molding at ambient
temperatures and above.
Improves part appearance and reduces defects
caused by sticking.
Contains no Class I or Class II Ozone Depleting
Substances
Contains no chlorinated solvents such as
1,1,1 trichloroethane or methylene chloride.
Colorless and non-staining.
Uses
Stoner
M802 Urethane Mold Release is a release
agent and anti-stick lubricant for molded urethanes and
similar materials.
PRODUCT INFORMATION
Stoner
M802
Urethane Mold Release
Rev 19.7
Made
inUSA
StonerMolding.com
1070 Robert Fulton Hwy. Quarryville, PA 17566 1-800-227-5538 1-717-786-7355
by | Sep 27, 2025
RELEASES COMPOUNDS POLISHES SEALERS
TR INDUSTRIES
11022 Vulcan Street
South Gate, CA 90280-0893
Phone 562 -923-0838 Fax 562-861-3475
www.trmoldrelease.com info@trmoldrelease.com
TR-309
REGULAR COMPOUND
MEDIUM CUTTING PASTE
DESCRIPTION:
TR-309 is a medium coarse off-white paste compound developed specifically for light oxidation and sanding scratch
removal on polyester gel-coats.
PRODUCT FEATURES:
Fast cutting action for quick effective removal light sanding marks
Good initial gloss achieved on finished parts when sanding for minor defect repair
Remains moist while buffing with less spotting and drying
Restores gloss to lightly oxidized & weathered finishes
Contains no silicones or waxes
Economically priced
PHYSICAL PROPERTIES:
Specific Gravity: 1.23 (10.25lbs./Gal)
Viscosity: soft paste water/petroleum emulsion blend
Color: off-white
USES:
To provide good initial uniform gloss while removing sanding scratches (600g-800g), light oxidation and minor
surface imperfections on all gel coated finishes.
APPLICATION:
Apply TR-309 to gel-coated surface and spread evenly. Using a high speed electric variable speed buffer equipped
with all wool twisted buffing pad set buffer speed to 2,400 RPM for best results. Work in a 2 x 2 overlapping
surface area using medium pressure to keep surface moist to avoid drying out and burnishing. As polish begins to
dry gradually reduce buffing pressure to achieve a smooth uniform gloss appearance. Use a buffing spur to clean
pad frequently during use to remove excess compound build up.
NOTE:
For optimum results polish with TR-308 Fine Finish II to achieve a high gloss mirror like swirl free finish after using
TR-309 regular compound.
PACKAGING:
TR-309 is available in Gallon 4×1 case, 5gal pail or 55gal drum. Recommended to store in a cool dry place to
maintain one year shelf life stability.
FOR INDUSTRIAL USE ONLY
The information contained herein is based on tests considered to be reliable and accurate. Because of the wide variance of associated materials
and conditions, however no warranty is expressed or implied. Each user is encouraged to prepare a test part for their particular application.
by | Sep 27, 2025
by | Sep 27, 2025
by | Sep 27, 2025
by | Sep 27, 2025
SAFETY DATA SHEET (SDS) VERSION 2.3.33 1/26/2018
4340 E Miraloma Ave (P) 714-854-9531
Anaheim, CA 92807 (F) 714-854-1689 1
SECTION 1 IDENTIFICATION AND COMPANY D ETAILS
Product Name: WP-1 FinishRite White
Product Code(s): COMA-01
Manufacturer:
Maverick Abrasives
4340 E Miraloma Ave
Anaheim, CA 92807
Telephone Number: 714-854-9531
Fax Number: 714-854-1689
SECTION 2 HAZARDOUS INGREDIENTS/IDENTITY INFORMATION
Aluminum Oxide CAS #1344-28-1 Non-Hazardous
Barium Sulfate CAS #7727-43-7 Non-Hazardous
Paraffin And Hydrocarbon CAS #8002-74-2 Non-Hazardous SECTION 3 HAZARD INFORMATION
Inhalation: Material not considered inhalation hazard. Buffing & polishing may produce dust which over long-term
exposure may result in lung-disease.
Ingestion: Should not be ingested.
Skin Contact: No danger upon skin contact. Can be rubbed off with a cloth and soap and water.
Eye Contact: May be mildly irritable to eye.
SECTION 4 FIRST AID MEASURES
Skin Contact: In case of incidental skin contact remove excess after industrial use with damp rag. Wash hands with
soap and water.
Eye Contact: Remove with warm water applied gently to eye, flushing for 15 minutes or until debris is completely
removed.
Ingestion: Contact your local medical professional for consultation upon ingestion.
Inhalation: N/A
SAFETY DATA SHEET (SDS) VERSION 2.3.33 1/26/2018
4340 E Miraloma Ave (P) 714-854-9531
Anaheim, CA 92807 (F) 714-854-1689 2
SECTION 5 FIRE-FIGHTING MEASURES
Suitable Extinguishing Media
Special Firefighting Procedures: No special firefighting procedures necessary.
Unusual Fire and Explosions Hazard: No unusual fire hazards present.
SECTION 6 ACCIDENTAL RELEASE MEASURES
No special release measures required. Use dry disposal collection.
Chemical Safety Goggles Splash Suit Gloves Rubber Boots
SECTION 7 PRECAUTIONS FOR SAFE HANDLING AND USE
Steps to be taken in the event of spillage or chemical release: Wear suitable protective clothing.
Waste Disposal Method: Dispose of in accordance with national and local regulations of inert non-hazardous waste
material.
Precautions to be taken in Handling and Storage: Store in a cool, dry place (2- 30 C) in original sealed containers
away from heat sources and sunlight. Avoid contact with strong oxidants and strong acids.
Other Precautions: N/A
SECTION 8 EXPOSURE CONTROLS AND PERSONAL PROTECTION
Occupational Exposure Limits: N/A
Respiratory System: Wear appropriate respirator when ventilation is inadequa te
Skin and Body: N/A
Hands: N/A
Eyes: N/A
Other/Special: N/A
SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES
Physical State: Paste/Liquid
Color: White
Odor: Click here to enter text.
SAFETY DATA SHEET (SDS) VERSION 2.3.33 1/26/2018
4340 E Miraloma Ave (P) 714-854-9531
Anaheim, CA 92807 (F) 714-854-1689 3
Melting Point: Click here to enter text.
Flash Point: Click here to enter text.
SECTION 10 REACTIVITY DATA
Stability: N/A
Conditions to Avoid: N/A
Incompatibility: N/A
Hazardous Decomposition or By-products: N/A
Hazardous Polymerization: N/A
SECTION 11 TOXICOLOGICAL INFORMATION
The toxicological information for the components is: Non -toxic.
SECTION 12 ECOLOGICAL INFORMATION
Data is not yet available
SECTION 13 DISPOSAL CONSIDERATIONS
This material is not regarded as hazardous waste. Observe all federal, state, and local environmental regulations.
SECTION 14 TRANSPORT INFORMATION
Non-hazardous for road, sea, and airfreight.
SECTION 15 REGULATORY INFORMATION
Irritant
Safety Phrases: S16 Keep away from sources of ignition No Smoking
S24/25 Avoid contact with skin & eyes.
S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
S36/37/39 Wear suitable protective clothing, gloves, and eye protection.
Risk Phrases: R10 Flammable
SAFETY DATA SHEET (SDS) VERSION 2.3.33 1/26/2018
4340 E Miraloma Ave (P) 714-854-9531
Anaheim, CA 92807 (F) 714-854-1689 4
Regulations: The Chemicals (Hazard Information and Packaging f or Supply) regulations 2002
1999/45/EC Dangerous Preparations Directive.
91/155/EC Safety Data Sheets Directive.
SECTION 16 OTHER INFORMATION
Notice to Reader:
To the best of our knowledge the information contained herein is accurate.
However, neither the named supplier nor any of its subsidiaries assumes any liability whatsoever for the accuracy
or completeness of the information contained herein.
Final determination of the suitability of any material is the sole responsibility of the user. All materials may present
unknown hazards and should be used with caution. Although certain hazards are described herein we cannot
guarantee that these are the only hazards that exist.
