by | Sep 27, 2025
LOW STYRENE ACRYLIC BONDING
POLYESTER RESIN
Typical Cast Mechanical Properties*
1 SEE BACK PAGE
Test Unit of Measure Nominal ISO Methods
Tensile Strength psi/MPa 11,600/80 ASTM D 638
Tensile Modulus psi/GPa 580,000/4.0 ASTM D 638
Tensile Elongation % 2.5 ASTM D 638
Flexural Strength psi/MPa 16,500/114 ASTM D 790
Flexural Modulus psi/GPa 620,000/4.3 ASTM D 790
Heat Distortion Temp. F/ C @ 264 psi 151/66 ASTM D 648
Typical Neat (Non-Filled) Liquid Properties*
2 SEE BACK PAGE
Version Gel Time Temp
Viscometer
Spindle
Speed
Viscosity
Thix
Index
Initiator
Level/Type
C431-PPC-18 18 mins 25. C
LV 3 @
6/60/6
400/2.3
1.25% MEKP-
925
*Typical properties are not to be construed as specifications.
DESCRIPTION
Altek C431-PPC-18 is AOC s new gen-
eration acrylic bonding resin. It is a
pre-promoted, thixotropic polyester
resin.
APPLICATION
Altek C431-PPC-18 is designed to be
used with filler and has been carefully
engineered to maximize filler loading
without compromising quality of fin-
ished parts. It is used for backing vacu-
umed formed acrylic.
BENEFITS
Unique design for quicker hard-
ness development, which speeds
up mold turnover and increases
rate of production
Excellent adhesive to formed acryl-
ic resulting in greater integrity of
the laminate and finished parts
Capable of higher filler loading
without loss of physical properties
insuring that as filler is increased,
the rate of cracking at demold
does not increase which maximiz-
es the end product
Designed for improved wet out and
roll out of the laminate
ALTEK C431-PPC-18
POLYESTER RESIN
AOC World Headquarters
955 Highway 57 East, Collierville, TN 38017
+01 901.854.2800
AOC-Resins.com
SALES CONTACTS
NORTH AMERICA
Toll free: +1 866 319 8827
northamerica@aoc-resins.com
EUROPE
+44 1206 390415
europe@aoc-resins.com
INDIA
+44 1206 390415
india@aoc-resins.com
LATIN AMERICA
+01 863 815 5016
latinamerica@aoc-resins.com
AOC UK LTD.
+44 01206 390400
salesUK@aoc-resins.com
ASIA/AUSTRALIA
+44 1206 390415
asia@aoc-resins.com
MIDDLE EAST
+44 1206 390415
middleeast@aoc-resins.com
AOC is a registered trademark of AOC, LLC.
The information contained in this data sheet is based on laboratory data and field experience. We believe this information to be reliable, but do not guarantee its applicability to the user s process or
assume any liability for occurrences arising out of its use. The user, by accepting the products described herein, agrees to be responsible for thoroughly testing each such product before commit-
ting to production. Our recommendations should not be taken as inducements to infringe any patent or violate any law, safety code or insurance regulation. This data sheet and its contents are the
confidential and proprietary information of AOC and it may not be modified altered deconstructed or presented in any other manner without the explicit authorization of AOC and/or its legal counsel.
ALTEK
C431-PPC-18 POLYESTER RESIN
PERFORMANCE GUIDELINES
A. Keep full strength catalyst levels
between 1.0% – 2.0% (1.25% mini-
mum with mechanical application)
of the total resin weight.
B. Maintaining shop temperatures be-
tween 65 F/18 C and 90 F/32 C
and humidity between 40% and 90%
will help the fabricator make a high
quality part. Consistent shop condi-
tions contribute to consistent gel times
viscosity.
STORAGE STABILITY
Resins are stable for three months
from the date of manufacture when
stored in the original containers, away
from sunlight at no more than
70 F/21 C. After extended storage,
some drift may occur in gel time.
During the hot summer months, no
more than two months stability at
86 F/30 C should be anticipated.
Storage in plastic totes made out of
materials such as polyethylene (PE) or
polypropylene (PP), in particular trans-
lucent PE/PP, will accelerate gel for-
mation and result in a significantly
reduced storage stability.
Storage of this resin outdoors in
translucent plastic totes may reduce
the storage stability to only a few
weeks. AOC cannot assume responsi-
bility for gel formation under these
storage conditions.
APPLICATION GUIDELINES
Due to the excellent curing character-
istics of the Altek C431-PPC-18 resin,
complete all secondary bonding as
soon as possible. Exposing the lami-
nate to sunlight will result in severe
secondary bonding problems. After 24
hours of cure, it may be necessary to
abrade the laminate to insure good
secondary bonding, especially if the
surface of the laminate is resin rich.
Avoid low fiberglass content and resin
puddling with this product.
Caution:
The ability of an unsaturated polyester
resin to bond to acrylic is influenced by
many factors. Resin is only one of
these factors. The type and amount of
filler used, type and color of acrylic
used, and the conditions during the
thermoforming process are but a few
of the factors that effect the ability of
the resin to bond to the acrylic. There-
fore, it is vitally important that the fab-
ricators evaluate for themselves the
fitness of this product for their pro-
cess.
To insure high quality fabricated parts,
AOC strongly encourages fabricators to
utilize “Best Practices Guidelines” for
polyester resin, ABS and acrylic sheet.
SAFETY
See the appropriate Safety Data Sheet
for guidelines.
ISO 9001:2015 CERTIFIED
The Quality Management Systems at
every AOC manufacturing facility have
been certified as meeting ISO
9001:2015 standards. This certifica-
tion recognizes that each AOC facility
has an internationally accepted model
in place for managing and assuring
quality. We follow the practices set
forth in this model to add value to the
resins we make for our customers.
FOOTNOTES
(1.) Based on tests of at 77 F/25 C and 50%
relative humidity. All tests performed on unrein-
forced cured resin castings. Castings were post
cured.
(2.) The gel times shown are typical but may be
affected by catalyst, promoter, inhibitor concentra-
tion, resin, mold, and shop temperature. Variations
in gelling characteristics can be expected between
different lots of catalysts and at extremely high
humidities. Pigment and/or filler can retard or
accelerate gelation. It is recommended that the
fabricator check the gelling characteristics of a
small quantity of resin under actual operating
conditions prior to use.
Pub. C431-C SERIES NA
Effective Date: October 2019
Copyright 2019
by | Sep 27, 2025
VICAST
A717-L SERIES
POLYESTER RESIN
ISO/NPG ACRYLIC MODIFIED POLYESTER RESIN
FOR SOLID SURFACE APPLICATIONS
Typical Cast Mechanical Properties
1
Test Unit of Measure Nominal Test Method
Tensile Strength psi/MPa 12,500/86.2 ASTM D 638
Tensile Modulus psi/GPa 580,000/4.0 ASTM D 638
Tensile Elongation % 3.9 ASTM D 638
Flexural Strength psi/MPa 20,800/143 ASTM D 790
Flexural Modulus psi/GPa 590,000/4.1 ASTM D 790
Heat Distortion Temp. F/ C @264 psi 167/75 ASTM D 648
Typical properties are not to be construed as specifications.
DESCRIPTION
Vicast A717-L Series is a high reac-
tivity, prepromoted ISO/NPG Acrylic
Modified solid surface casting resin.
This resin has been designed to be
used to produce solid color and
granite effect sheets and bowls.
Vicast A717-L Series is designed to
provide extreme versatility in select-
ing the combination of gel time and
viscosity that suits the specific man-
ufacturing process, working condi-
tions and raw materials.
BENEFITS
Premium ISO/NPG polymer
Acrylic modified
Low color
Fast cure
Excellent stain and blush re-
sistance
Increased UV stability
Consistent, accurate coloring of
cured solid surface
Fast demold
Typical Liquid Properties
2
Versions MEKP %
Gel
Time,
Min
Gel to
Peak
Peak
Exotherm
( F/ C)
VISC SP rpm cps NVM %
A717-LBA-10 DDM-9 1 10 10 361/183 LVSSA
1 34 60 700 65
A717-LBA-20 DDM-9 1 20 10 352/178 LVSSA
1 34 60 700 65
A717-LBB-20 DDM-9 1 20 14 347/175 LVSSA
1 34 20 700 65
A717-LRB-25 DDM-9 1 25 10 352/178 LVSSA
1 34 60 700 65
A717-LRD-20 DDM-9 1 20 13 352/178 LVSSA
1 34 60 700 65
AOC World Headquarters
955 Highway 57 East, Collierville, TN 38017
+01 901.854.2800
AOC-Resins.com
SALES CONTACTS
NORTH AMERICA
Toll free: +1 866 319 8827
northamerica@aoc-resins.com
EUROPE
+44 1206 390415
europe@aoc-resins.com
INDIA
+44 1206 390415
india@aoc-resins.com
LATIN AMERICA
+01 863 815 5016
latinamerica@aoc-resins.com
AOC UK LTD.
+44 1206 390400
salesUK@aoc-resins.com
ASIA/AUSTRALIA
+44 1206 390415
asia@aoc-resins.com
MIDDLE EAST
+44 1206 390415
middleeast@aoc-resins.com
AOC is a registered trademark of AOC, LLC.
The information contained in this data sheet is based on laboratory data and field experience. We believe this information to be reliable, but do not guarantee its applicability to the user s process or
assume any liability for occurrences arising out of its use. The user, by accepting the products described herein, agrees to be responsible for thoroughly testing each such product before commit-
ting to production. Our recommendations should not be taken as inducements to infringe any patent or violate any law, safety code or insurance regulation. This data sheet and its contents are the
confidential and proprietary information of AOC and it may not be modified altered deconstructed or presented in any other manner without the explicit authorization of AOC and/or its legal counsel.
VICAST
A717-L SERIES POLYESTER RESIN
PERFORMANCE GUID ELINES
A. Keep full strength catalyst levels
between 1.0% – 2.0% of the total resin
weight.
B. Maintaining shop temperatures
between 65 F/ 18 C and 90 F/32 C
and humidity between 40% and 90%
will help the fabricator make a high
quality part. Consistent shop conditions
contribute to consistent gel times.
C. Sanding and/or grinding is recom-
mended if a secondary bond is applied
to a laminate that was made with a
resin containing wax.
STORAGE STABILITY
This product is stable for three months
from the date of manufacture when
stored in the original containers, away
from direct sunlight or other UV light
sources and at or below 77 F/25 C.
Storage stability of two months or less
should be anticipated if the storage
temperature exceeds 86 F/30 C.
After extended storage, some drift may
occur in the product viscosity and gel
time.
SAFETY
See the appropriate Safety Data Sheet
for guidelines.
ISO 9001:2008 CERTIFIED
The Quality Management Systems at
every AOC manufacturing facility have
been certified as meeting ISO
9001:2008 standards. This certifica-
tion recognizes that each AOC facility
has an internationally accepted model
in place for managing and assuring
quality. We follow the practices set
forth in this model to add value to the
resins we make for our customers.
FOOTNOTES
(1.) Based on tests at 77 F/25 C and 50% rela-
tive humidity. All tests performed on unreinforced
cured resin castings. Thixotropic components, if
applicable, are excluded from casting samples.
Castings were post cured.
(2.) The gel times shown are typical but may be affected
by catalyst, promoter, inhibitor concentration, resin,
mold, and shop temperature. Variations in gelling char-
acteristics can be expected between different lots of
catalysts and at extremely high humidities. Pigment
and/or filler can retard or accelerate gelation. It is rec-
ommended that the fabricator check the gelling charac-
teristics of a small quantity of resin under actual operat-
ing conditions prior to use.
Pub. A717-L SERIES
Effective Date: June 2017
Copyright 2017
by | Sep 27, 2025
ALTEK
R589 SERIES
POLYESTER RESIN
POLYESTER RESIN FOR RTM
Typical Cast Mechanical Properties
1
Test Unit of Measure Nominal Test Method
Tensile Strength psi/MPa 12,000/83 ASTM D 638
Tensile Modulus psi/GPa 590,000/4.1 ASTM D 638
Tensile Elongation % 2.9 ASTM D 638
Flexural Strength psi/MPa 20,930/144 ASTM D 790
Flexural Modulus psi/GPa 640,000/4.4 ASTM D 790
Heat Distortion Temp. F/ C @264 psi 158/70 ASTM D 648
Typical Liquid Properties
2
Versions
Catalyst
Type
%
Gel
Time
min
Gel
To
Peak
Peak
Exotherm,
F/C
Visc rpm
SP
#
cps
Styrene
%
R589-ACC-10 MEKP-925 1.25 9 15 338/170 RV 20 2 250 39
*Typical properties are not to be construed as specifications.
DESCRIPTION
AOC’s Altek R589 Series is a
prepromoted polyester resin system.
It is designed to be used in RTM.
It is a higher reactive orthophthalic
product with superior physical proper-
ties.
APPLICATION
AOC’s Altek R589 Series is used in
RTM (Resin Transfer Molding) and
RTML processes. Uses range from RV
parts to fan shrouds and other special
need applications.
BENEFITS
This resin is characterized by its:
Low viscosity
Rapid wet-out
Superior physical properties
AOC World Headquarters
955 Highway 57 East, Collierville, TN 38017
+01 901.854.2800
AOC-Resins.com
SALES CONTACTS
NORTH AMERICA
Toll free: +1 866 319 8827
northamerica@aoc-resins.com
EUROPE
+44 1206 390415
europe@aoc-resins.com
INDIA
+44 1206 390415
india@aoc-resins.com
LATIN AMERICA
+01 863 815 5016
latinamerica@aoc-resins.com
AOC UK LTD.
+44 01206 390400
salesUK@aoc-resins.com
ASIA/AUSTRALIA
+44 1206 390415
asia@aoc-resins.com
MIDDLE EAST
+44 1206 390415
middleeast@aoc-resins.com
AOC is a registered trademark of AOC, LLC.
The information contained in this data sheet is based on laboratory data and field experience. We believe this information to be reliable, but do not guarantee its applicability to the user s
process or assume any liability for occurrences arising out of its use. The user, by accepting the products described herein, agrees to be responsible for thoroughly testing
each such product before committing to production. Our recommendations should not be taken as inducements to infringe any patent or violate any law, safety code or insurance regulation.
Data Sheet and its contents are the confidential and proprietary information of AOC and it may not be modified altered deconstructed or presented in any other manner without the explicit authorization of AOC and/or its legal counsel.
ALTEK
R589 SERIES POLYESTER RESIN
PERFORMANCE GUID ELINES
A. Keep full strength catalyst lev-
els between 1.0% – 2.0% of the to-
tal resin weight.
B. Maintain shop temperatures be-
tween 65 F/18 C and 90 F/32 C
and humidity between 40% and
90%. Consistent shop conditions
contribute to consistent gel time
and will help the fabricator make a
high quality part.
C. Sanding and/or grinding is rec-
ommended if a secondary bond is
applied to a laminate that was
made with a resin containing wax.
STORAGE STABILITY
This product is stable for three
months from the date of manufac-
ture when stored in the original con-
tainers, away from direct sunlight or
other UV light sources and at or be-
low 77 F/25 C.
After extended storage, some drift
may occur in the product viscosity
and gel time.
SAFETY
See the appropriate Safety Data Sheet
for guidelines.
ISO 9001:2008 CERTIFIED
The Quality Management Systems at
every AOC manufacturing facility have
been certified as meeting ISO
9001:2008 standards. This certifica-
tion recognizes that each AOC facility
has an internationally accepted model
in place for managing and assuring
quality. We follow the practices set
forth in this model to add value to the
resins we make for our customers.
FOOTNOTES
(1.) Based on tests at 77 F/25 C and 50% rela-
tive humidity. All tests performed on unreinforced
cured resin castings. Thixotropic components, if
applicable, are excluded from casting samples.
Castings were post cured.
(2.) The gel times shown are typical but may be
affected by catalyst, promoter, inhibitor concentra-
tion, resin, mold, and shop temperature. Variations
in gelling characteristics can be expected between
different lots of catalysts and at extremely high
humidities. Pigment and/or filler can retard or
accelerate gelation. It is recommended that the
fabricator check the gelling characteristics of a
small quantity of resin under actual operating
conditions prior to use.
Pub. R589 Series NA
Effective Date: Feb. 2017
Copyright 2017
by | Sep 27, 2025
INTERPLASTIC CORPORATION MAKES NO WARRANTIES REGARDING ANY MATERIAL AND/OR SAMPLES DESCRIBED IN THIS
REPORT. ALL PROPERTIES SPECIFIED ABOVE ARE APPROXIMATE AND MAY VARY FROM MATERIAL DELIVERED. DELIVERED
MATERIAL COMPLIES WITH THE CERTIFICATE OF ANALYSIS ON EACH SHIPMENT OF PRODUCT. INTERPLASTIC CORPORATION
MAKES NO REPRESENTATIONS OF FACT REGARDING THE MATERIAL EXCEPT THOSE SPECIFIED ABOVE. FINAL DETERMINATION
OF PART OR APPLICATION AND THE SUITABILITY OF THE MATERIAL FOR THE USE CONTEMPLATED IS THE SOLE
RESPONSIBILITY OF THE BUYER. OUR TECHNICAL SALES REPRESENTATIVES WILL ASSIST IN DEVELOPING PROCEDURES TO FIT
INDIVIDUAL REQUIREMENTS AS A CUSTOMER ACCOMMODATION, BUT ALL ADVICE IS ACCEPTED AT YOUR RISK AND SHOULD
BE CHECKED FOR SUITABILITY TO YOUR PARTICULAR PROCESSES AND NEEDS. THESE TEST DATA AND PROPERTIES ARE BASED
ON RESULTS OBTAINED FOR A SPECIFIC MATERIAL UNDER THE SPECIFIED TEST CONDITIONS – THEY ARE NOT TO BE USED AS
SPECIFICATIONS AND ARE NOT WARRANTED AS PERFORMANCE ATTRIBUTES FOR ANY PRODUCT OR SYSTEM.
INTERPLASTIC CORPORATION
2015 Northeast Broadway Street
Minneapolis, Minnesota 55413-1775
651.481.6860 Fax 612.331.4235
www.interplastic.com
Revised: 8/18 Page 1 of 2
CORVE8730 is a non-promoted, epoxy novolac-based vinyl ester resin. This high cross-link density resin has a heat
distortion point of 280 F (138 C) and exceptional chemical resistance. Typical uses are filament winding and hand lay-up
of reinforced plastic tanks, pipe and process equipment, etc. Its high heat distortion point also makes this resin an
outstanding choice for high temperature applications.
FEATURES BENEFITS
High Physical Properties Makes extremely tough composites
Highly Versatile Viscosity Properties Formulated for spray-up and hand lay-up needs
Non-Promoted Resin System Able to adapt to customer-specific conditions
Outstanding Corrosion Resistance Resists caustic and solvent with hydrolytic stability
High Heat Distortion Resistance Maintains dimensional stability
RELATED PRODUCTS GEL TIME
MVR8071-40 35-43 Minutes
LIQUID PROPERTIES RESULTS
Viscosity, Brookfield Model LV, #3 Spindle @ 60 rpm, 77 F (25 C), cPs 250-400
100 grams resin @ 77 F (25 C), promoted with 0.20 gram of 12% cobalt, initiated
with 1.2% MEKP-925H by volume*
Gel Time, min:sec 16:00-19:00
Gel to Peak Exotherm Time, min:sec 6:00-14:00
Peak Exotherm 370-410 F (187-210 C)
Non-Volatile Content, % 62.0-66.5
Hazardous Air Pollutant (Styrene) Content, % 33.5-38.0
Specific Gravity 1.05-1.09
TYPICAL PROPERTIES
Thickness 1/8 inch (3.2 mm) Casting
Construction Not Applicable
Flexural Strength, ASTM D790 18,400 psi 127 MPa
Flexural Modulus, ASTM D790 5.2 x 10
5
psi 3,586 MPa
Tensile Strength, ASTM D638 10,400 psi 72 MPa
Tensile Modulus, ASTM D638 5.3 x 10
5
psi 3,655 MPa
Tensile Elongation, ASTM D638 3.0 % 3.0 %
Barcol Hardness, 934-1 gauge, ASTM D2583 38 38
Heat Distortion Temperature, ASTM D648 280 F 138 C
Specific Gravity, ASTM D792 1.19 1.19
*Gel time and reactivity will vary due to the type and concentration of Free Radical Initiator (catalyst), shop temperature, humidity, and type of fillers used. In order to meet
your individual needs consult our technical sales representative for assistance. If using methyl ethyl ketone peroxide (MEKP) to gel and cure CoREZYN vinyl ester resins,
we recommend only these three brands: Cadox L-50a (Nouryon), Luperox DHD-9 (Arkema), and Norox MEKP-925 (United Initiators). These must be used at the
appropriate percentage and suitable temperature. Contact your Interplastic Corporation representative for assistance.
CORVE8730
Vinyl Resin
Technical Data Sheet
INTERPLASTIC CORPORATION MAKES NO WARRANTIES REGARDING ANY MATERIAL AND/OR SAMPLES DESCRIBED IN THIS
REPORT. ALL PROPERTIES SPECIFIED ABOVE ARE APPROXIMATE AND MAY VARY FROM MATERIAL DELIVERED. DELIVERED
MATERIAL COMPLIES WITH THE CERTIFICATE OF ANALYSIS ON EACH SHIPMENT OF PRODUCT. INTERPLASTIC CORPORATION
MAKES NO REPRESENTATIONS OF FACT REGARDING THE MATERIAL EXCEPT THOSE SPECIFIED ABOVE. FINAL DETERMINATION
OF PART OR APPLICATION AND THE SUITABILITY OF THE MATERIAL FOR THE USE CONTEMPLATED IS THE SOLE
RESPONSIBILITY OF THE BUYER. OUR TECHNICAL SALES REPRESENTATIVES WILL ASSIST IN DEVELOPING PROCEDURES TO FIT
INDIVIDUAL REQUIREMENTS AS A CUSTOMER ACCOMMODATION, BUT ALL ADVICE IS ACCEPTED AT YOUR RISK AND SHOULD
BE CHECKED FOR SUITABILITY TO YOUR PARTICULAR PROCESSES AND NEEDS. THESE TEST DATA AND PROPERTIES ARE BASED
ON RESULTS OBTAINED FOR A SPECIFIC MATERIAL UNDER THE SPECIFIED TEST CONDITIONS – THEY ARE NOT TO BE USED AS
SPECIFICATIONS AND ARE NOT WARRANTED AS PERFORMANCE ATTRIBUTES FOR ANY PRODUCT OR SYSTEM.
INTERPLASTIC CORPORATION
2015 Northeast Broadway Street
Minneapolis, Minnesota 55413-1775
651.481.6860 Fax 612.331.4235
www.interplastic.com
Revised: 8/18 Page 2 of 2
TYPICAL 100-GRAM CUP GEL TIME CHART FOR LOWER EXOTHERM WITH CUMENE HYDROPEROXIDE (CHP)
Temperature ( F/ C) 12% Cobalt (Wt%) DMA (Wt%) 2,4-Pentanedione (Wt%) CHP (Wt%) Gel Time* (min)
60/16 0.2 0.2 0 1.5 34
60/16 0.2 0.1 0 2 39
60/16 0.2 0.1 0 1.5 48
77/25 0.2 0.2 0 1.5 22
77/25 0.3 0.1 0 1.5 24
77/25 0.2 0.1 0 1.5 29
77/25 0.2 0.1 0 2 30
77/25 0.2 0.1 0.05 1.5 43
77/25 0.3 0.1 0.1 1.5 48
77/25 0.2 0.1 0.1 2 55
77/25 0.2 0.2 0.1 1.5 51
77/25 0.2 0.1 0.1 1.5 63
77/25 0.2 0.1 0.15 1.5 85
90/32 0.2 0.1 0 1.5 15
90/32 0.2 0.1 0.05 1.5 26
90/32 0.2 0.1 0.1 1.5 30
*Gel time is run in a 100-gram mass at the specified temperature.
by | Sep 27, 2025
All specifications and properties specified above are approximate. Specifications and properties of material delivered may vary slightly
from those given above. Interplastic Corporation makes no representations of fact regarding the material except those specified above.
No person has any authority to bind Interplastic Corporation to any representation except those specified above. Final determination of
the suitability of the material for the use contemplated is the sole responsibility of the Buyer. Our technical sales representatives will
assist in developing procedures to fit individual requirements, but all advice is accepted at your risk and should be checked for
suitability to your particular processes. These test data and properties are based on results obtained for a specific material under the
specified test conditions. They are not to be used as specifications and are not warranted as performance attributes for any product or
system. Specifications and properties of standard production material may vary slightly from those in this report. Interplastic
Corporation makes no warranties regarding any material and/or samples described in this report unless that representation is provided
to your company in writing by a Technical Director of Interplastic Corporation or one of his or her managers.
INTERPLASTIC CORPORATION
2015 Northeast Broadway Street
Minneapolis, Minnesota 55413-1775
651.481.6860 Fax 612.331.4235
www.interplastic.com
Revised: 9/16
CORVE8441B is a promoted, thixotropic, corrosion resistant, fire retardant, vinyl ester resin that meets the Flame Grade
A, Physicals Grade A, and Electrical Class O requirements of MIL-R-21607E (SH) and is on the QPL-21607-29 list. This
product also meets the Grade B and Class 1 and Class 2 requirements of MIL-R-24719 (SH).
RELATED PRODUCTS GEL TIME
CORVE8441BW 8-12 Minutes
CORVE8441BS 25-30 Minutes
LIQUID PROPERTIES RESULTS
Viscosity, Brookfield Model LV #3 Spindle @ 60 rpm, 77 F (25 C), cPs 450-550
Thixotropic Index 1.6-2.0
100 grams resin @ 77 F (25 C), initiated with 1.2cc MEKP-925H *
Gel Time, min:sec 15:00-20:00
Gel to Peak Exotherm Time, min:sec 12:00-17:00
Peak Exotherm 320-350 F (160-176 C)
Non-Volatile Content, % 57.0-62.0
Hazardous Air Pollutant (Styrene) Content, % 38.0-43.0
Acid Value (solids) 10-17
Specific Gravity 1.13-1.16
TYPICAL PROPERTIES
Thickness 1/8 inch (3.2 mm) Casting
Construction Not Applicable
Flexural Strength, ASTM D790 16,600 psi 115 MPa
Flexural Modulus, ASTM D790 4.7 x 10
5
psi 3,241 MPa
Tensile Strength, ASTM D638 11,700 psi 81 MPa
Tensile Modulus, ASTM D638 4.8 x 10
5
psi 3,331 MPa
Tensile Elongation, ASTM D638 4.5 % 4.5 %
Barcol Hardness, 934-1 gauge, ASTM D2583 40 40
Heat Distortion Temperature, ASTM D648 230 F 110 C
* Gel time and reactivity will vary due to the type and concentration of Free Radical Initiator (catalyst), shop temperature, humidity, and type of fillers used. In order to meet
your individual needs consult our technical sales representative for assistance. If using methyl ethyl ketone peroxide (MEKP) to gel and cure CoREZYN vinyl ester
resins, we recommend only these three brands: Cadox L-50a (Akzo Nobel); Luperox DHD-9 (Arkema); and Norox MEKP-925H (United Initiators). These must be
used at the appropriate percentage and suitable temperature. Contact your Interplastic Corporation representative for assistance.
TYPICAL FLAME TEST PROPERTIES
Thickness 1/8 inch (3.2 mm) Laminate
Construction 4 Plies 1.5 oz/ft
2
, 33% Glass Mat
ASTM D635, Horizontal Burn Rate < 1
ASTM E84, Flame Spread 26.2
ASTM E84, Smoke Density 1,288
UL 94 (This is not to imply UL warranty) (V-O) (HB < 1 ) (5V Pass)
HLT 15 100
CORVE8441B
Thixotropic Vinyl Ester Resin
Technical Data Sheet
by | Sep 27, 2025
Interplastic Corporation makes no warranties regarding any material and/or samples described in this report. All properties
specified above are approximate and may vary from material delivered. Delivered material complies with the certificate of
analysis on each shipment of product. Interplastic Corporation makes no representations of fact regarding the material
except those specified above. Final determination of part or application and the suitability of the material for the use
contemplated is the sole responsibility of the buyer. Our technical sales representatives will assist in developing procedures
to fit individual requirements as a customer accommodation, but all advice is accepted at your risk and should be checked for
suitability to your particular processes and needs. These test data and properties are based on results obtained for a specific
material under the specified test conditions – they are not to be used as specifications and are not warranted as performance
attributes for any product or system.
INTERPLASTIC CORPORATION
2015 Northeast Broadway Street
Minneapolis, Minnesota 55413-1775
651.481.6860 Fax 612.331.4235
www.interplastic.com
Revised: 2/18
CORVE8440 is a non-promoted, fire retardant, vinyl ester resin. It has an ASTM E84 Tunnel Test flame spread rating of
<75 (Class 2 flame spread) without additives and < 25 (Class 1 flame spread) with the addition of 1.5% antimony trioxide.
FEATURES BENEFITS
Brominated Version of CORVE8300 Very versatile and widely used vinyl ester resin
Highly Corrosion Resistant Resists acid, alkali, and oxidizing chemical environments
Contains 40% Styrene Meets many requirements for low HAP content
Excellent Physical Properties Suitable for tanks, pipe, and process equipment
Non-Promoted Resin System Adjustable for most customer applications
LIQUID PROPERTIES RESULTS
Viscosity, Brookfield Model LV, #3 Spindle @ 60 rpm, 77 F (25 C), cPs 450-550
100 grams resin @ 77 F (25 C), promoted with 0.20 grams of 12% Cobalt and
0.05 grams N,N-Dimethylaniline, initiated with 1.2% MEKP-925H by volume *
Gel Time, min:sec 16:00-19:00
Gel to Peak Exotherm Time, min:sec 9:30-15:00
Peak Exotherm 315-355 F (157-179 C)
Non-Volatile Content, % 58.5-61.5
Hazardous Air Pollutant (Styrene) Content, % 38.5-41.5
Specific Gravity 1.14-1.17
TYPICAL PROPERTIES
Thickness 1/8 inch (3.2 mm) Casting 1/8 inch (3.2 mm) Laminate
Construction Not Applicable 4 Plies 1.5 oz/ft
2
, 33% Glass Mat
Flexural Strength, ASTM D790 22,000 psi 150 MPa 25,400 psi 175 MPa
Flexural Modulus, ASTM D790 5.6 x 10
5
psi 3,800 MPa 11.0 x 10
5
psi 7,586 MPa
Tensile Strength, ASTM D638 13,000 psi 89 MPa 13,900 psi 85.8 MPa
Tensile Modulus, ASTM D638 5.1 x 10
5
psi 3,500 MPa 12.8 x 10
5
psi 8,828 MPa
Tensile Elongation, ASTM D638 6.4 % 6.4 % 1.4 % 1.4 %
Barcol Hardness, 934-1 gauge, ASTM D2583 34 34 44-48 44-48
Heat Distortion Temperature, ASTM D648 220 F 104 C >400 F >200 C
* Gel time and reactivity will vary due to the type and concentration of Free Radical Initiator (catalyst), shop temperature, humidity, and type of fillers used. In order to meet
your individual needs consult our technical sales representative for assistance. If using methyl ethyl ketone peroxide (MEKP) to gel and cure CoREZYN vinyl ester resins
we recommend only these three brands: Cadox L-50a (Nouryon); Luperox DHD-9 (Arkema); and Norox MEKP-925H (United Initiators). These must be used at the
appropriate percentage and suitable temperature. Contact your Interplastic Corporation representative for assistance.
FLAME TEST PROPERTIES
Thickness 1/8 inch (3.2 mm) Laminate
Construction 4 Plies 1.5 oz/ft
2
, 33% Glass Mat
ASTM E84, Flame Spread 45
ASTM E84, Flame Spread (with 1.5% Antimony Trioxide added to the resin) 15
ASTM E84, Flame Spread (with 3.75 % Nyacol APE 3040 added to the resin) 20
ASTM D635, Horizontal Burn Rate < 1
UL 94 **This is not to imply UL warranty (V-O) (HB < 1 ) (5V Pass)
HLT 15 20
CORVE8440
Fire Retardant Vinyl Ester Resin
Technical Data Sheet
by | Sep 27, 2025
All specifications and properties specified above are approximate. Specifications and properties of material delivered may vary slightly
from those given above. Interplastic Corporation makes no representations of fact regarding the material except those specified above.
No person has any authority to bind Interplastic Corporation to any representation except those specified above. Final determination of
the suitability of the material for the use contemplated is the sole responsibility of the Buyer. Our technical sales representatives will
assist in developing procedures to fit individual requirements, but all advice is accepted at your risk and should be checked for
suitability to your particular processes. These test data and properties are based on results obtained for a specific material under the
specified test conditions. They are not to be used as specifications and are not warranted as performance attributes for any product or
system. Specifications and properties of standard production material may vary slightly from those in this report. Interplastic
Corporation makes no warranties regarding any material and/or samples described in this report unless that representation is provided
to your company in writing by a Technical Director of Interplastic Corporation or one of his or her managers.
INTERPLASTIC CORPORATIO N
2015 Northeast Broadway Street
Minneapolis, Minnesota 55413-1775
651.481.6860 Fax 612.331.4235
www.interplastic.com
Revised: 1/18
CORVE8401 is a promoted, fire retardant, vinyl ester resin. This resin has a flame spread rating of < 25 (Class 1) per
ASTM E84 Tunnel Test without additives. Contact your Interplastic Corporation representative for specific corrosion
recommendations.
FEATURES BENEFITS
Flame Spread Rating < 25 per ASTM E84 No additives to cloud laminates; easy inspections
Highly Corrosion Resistant Resists acid, alkali, and oxidizing chemical environments
Excellent Physical Properties Suitable for tanks, pipe, and process equipment
RELATED PRODUCTS GEL TIME
CORVE8401W 8.5-11.5 Minutes
CORVE8401S 32-40 Minutes
LIQUID PROPERTIES RESULTS
Viscosity, Brookfield Model LV #3 Spindle @ 60 rpm, 77 F (25 C), cPs 400-600
100 grams resin @ 77 F (25 C), initiated with 1.2% MEKP-925H by volume *
Gel Time, min:sec 16:00-19:00
Gel to Peak Exotherm Time, min:sec 9:00-20:00
Peak Exotherm 300-350 F (149-177 C)
HAP Content, % 37.0-42.0
Specific Gravity 1.15-1.17
TYPICAL PROPERTIES
Thickness 1/8 inch (3.2 mm) Casting 1/8 inch (3.2 mm) Laminate
Construction Not Applicable 4 Plies 1.5 oz/ft
2
, 33% Glass Mat
Flexural Strength, ASTM D790 22,000 psi 150 MPa 25,400 psi 175 MPa
Flexural Modulus, ASTM D790 5.6 x 10
5
psi 3,800 MPa 11.0 x 10
5
psi 7,586 MPa
Tensile Strength, ASTM D638 13,000 psi 89 MPa 13,900 psi 85.8 MPa
Tensile Modulus, ASTM D638 5.1 x 10
5
psi 3,500 MPa 12.8 x 10
5
psi 8,828 MPa
Tensile Elongation, ASTM D638 6.4 % 6.4 % 1.4 % 1.4 %
Barcol Hardness, 934-1 gauge, ASTM D2583 34 34 44-48 44-48
Heat Distortion Temperature, ASTM D648 220 F 104 C -- F -- C
* Gel time and reactivity will vary due to the type and concentration of Free Radical Initiator (catalyst), shop temperature, humidity, and type of fillers used. In order to meet
your individual needs consult our technical sales representative for assistance. If using methyl ethyl ketone peroxide (MEKP) to gel and cure CoREZYN vinyl ester resins
we recommend only these three brands: Cadox L-50a (Akzo Nobel); Luperox DHD-9 (Arkema); and Norox MEKP-925H (United Initiators). These must be used at
the appropriate percentage and suitable temperature. Contact your Interplastic Corporation representative for assistance.
FLAME TEST PROPERTIES
Thickness 1/8 inch (3.2 mm) Laminate
Construction 4 Plies 1.5 oz/ft
2
, 33% Glass Mat
ASTM D635, Horizontal Burn Rate < 1
ASTM E84, Flame Spread 25
UL 94 **This is not to imply UL warranty (V-O) (HB < 1 ) (5V Pass)
HLT 15 100
CORVE8401
Fire Retardant Vinyl Ester Resin
Technical Data Sheet
by | Sep 27, 2025
All specifications and properties specified above are approximate. Specifications and properties of material delivered may vary slightly
from those given above. Interplastic Corporation makes no representations of fact regarding the material except those specified above.
No person has any authority to bind Interplastic Corporation to any representation except those specified above. Final determination of
the suitability of the material for the use contemplated is the sole responsibility of the Buyer. Our technical sales representatives will
assist in developing procedures to fit individual requirements, but all advice is accepted at your risk and should be checked for
suitability to your particular processes. These test data and properties are based on results obtained for a specific material under the
specified test conditions. They are not to be used as specifications and are not warranted as performance attributes for any product or
system. Specifications and properties of standard production material may vary slightly from those in this report. Interplastic
Corporation makes no warranties regarding any material and/or samples described in this report unless that representation is provided
to your company in writing by a Technical Director of Interplastic Corporation or one of his or her managers.
INTERPLASTIC CORPORATION
2015 Northeast Broadway Street
Minneapolis, Minnesota 55413-1775
651.481.6860 Fax 612.331.4235
www.interplastic.com
Revised: 9/21/17
CORVE8425 is a corrosion resistant, promoted, thixotropic vinyl ester resin for use in open molding applications.
FEATURES BENEFITS
100% Vinyl Ester Resin Excellent physical and corrosion properties
Promoted Resin System Ready for immediate use in customer applications
Class 1 Out of the Drum No special mixing equipment or other materials needed
Contains Less Than 46.2% Styrene (HAP) Federal MACT-Open Molding Non-Atomized
Corrosion Resistant resin
Contains Less Than 48% VOC SCAQMD Rule 1162-compliant corrosion resistant resin
RELATED PRODUCTS GEL TIME
CORVE8425-30 25-35 Minutes
LIQUID PROPERTIES RESULTS
Viscosity, Brookfield Model LV #3 Spindle @ 60 rpm, 77 F (25 C), cps (see Note 1 below) 450-650
Thixotropic Index 2.0-3.5
100 grams neat resin @ 77 F (25 C), initiated with 1.75% MEKP-925H by weight *
Gel Time, min:sec 15:00-20:00
Gel to Peak Exotherm Time, min:sec 9:00-16:00 G
Peak Exotherm 315-375 F (157-191 C)
Non-Volatile Content, % 52.1-55.0
Hazardous Air Pollutant (Styrene) Content, % <46.2
VOC Content, % 45.0-47.9
Specific Gravity 1.15-1.17
Note 1: The viscosity sample is mix well, adjusted to 77 F, and allowed to sit unagitated in a 77 F water bath for 20-22 minutes before the
viscosity measurements are performed.
G Denotes guideline. This is a typical result but not a specification.
TYPICAL PROPERTIES
Thickness 1/8 inch (3.2 mm) Casting 1/8 inch (3.2 mm) Laminate
Construction Not Applicable 4 Plies 1.5 oz/ft
2
, 33% Glass Mat
Flexural Strength, ASTM D790 19 ,500 psi 134 MPa 25,400 psi 175 MPa
Flexural Modulus, ASTM D790 4.7 x 10
5
psi 3,200 MPa 11.0 x 10
5
psi 7,590 MPa
Tensile Strength, ASTM D638 12,700 psi 88 MPa 13,900 psi 85.8 MPa
Tensile Modulus, ASTM D638 4.8 x 10
5
psi 3,300 MPa 12.8 x 10
5
psi 8,830 MPa
Tensile Elongation, ASTM D638 4.0 % 4.0 % 1.4 % 1.4 %
Barcol Hardness, 934-1 gauge, ASTM D2583 35 35 44-48 44-48
Heat Distortion Temperature, ASTM D648 225 F 107 C -- F -- C
* Gel time and reactivity will vary due to the type and concentration of Free Radical Initiator (catalyst), shop temperature, humidity, and type of fillers used. In order to meet
your individual needs consult our technical sales representative for assistance. If using methyl ethyl ketone peroxide (MEKP) to gel and cure CoREZYN vinyl ester
resins, we recommend only these three brands: Cadox L-50a (Akzo Nobel); Luperox DHD-9 (Arkema); and Norox MEKP-925H (United Initiators). These must be
used at the appropriate percentage and suitable temperature. Contact your Interplastic Corporation representative for assistance.
FLAME TEST PROPERTIES
Construction 2 Plies 0.75 oz/ft
2
, 37% Glass Mat
ASTM E84, Flame Spread Index 18.3
ASTM E84, Smoke Development Index 140
CORVE8425
Corrosion Resistant Vinyl Ester Resin
Technical Data Sheet
by | Sep 27, 2025
Interplastic Corporation makes no warranties regarding any material and/or samples described in this report. All properties
specified above are approximate and may vary from material delivered. Delivered material complies with the Certificate of
Analysis on each shipment of product. Interplastic Corporation makes no representations of fact regarding the material
except those specified above. Final determination of part or application and the suitability of the material for the use
contemplated is the sole responsibility of the buyer. Our technical sales representatives will assist in developing procedures
to fit individual requirements as a customer accommodation, but all advice is accepted at your risk and should be checked for
suitability to your particular processes and needs. These test data and properties are based on results obtained for a specific
material under the specified test conditions. They are not to be used as specifications and are not warranted as performance
attributes for any product or system.
INTERPLASTIC CORPORATION
2015 Northeast Broadway Street
Minneapolis, Minnesota 55413-1775
651.481.6860 Fax 612.331.4235
www.interplastic.com
Revised: 7/20
FOR DANIEL COMPANY ONLY
CORVE8401D is a promoted, fire retardant, vinyl ester resin. This resin has a flame spread rating of < 25 (Class 1) per
ASTM E84 Tunnel Test without additives. Contact your Interplastic Corporation representative for specific corrosion
recommendations.
FEATURES BENEFITS
Flame Spread Rating 25 per ASTM E84 No additives to cloud laminates; easy inspections
Highly Corrosion Resistant Resists acid, alkali, and oxidizing chemical environments
Excellent Physical Properties Suitable for tanks, pipe, and process equipment
RELATED PRODUCTS GEL TIME
CORVE8401DS 32-40 Minutes
LIQUID PROPERTIES RESULTS
Viscosity, Brookfield Model LV #3 Spindle @ 60 rpm, 77 F (25 C), cPs 400-500
100 grams resin @ 77 F (25 C), initiated with 1.2% MEKP-925H by volume *
Gel Time, min:sec 15:00-20:00
Gel to Peak Exotherm Time, min:sec 12:00-18:30
Peak Exotherm 310-360 F (154-182 C)
HAP Content, % styrene 39.5-41.0
Specific Gravity 1.14-1.17
TYPICAL PROPERTIES
Thickness 1/8 inch (3.2 mm) Casting 1/8 inch (3.2 mm) Laminate
Construction Not Applicable 4 Plies 1.5 oz/ft
2
, 33% Glass Mat
Flexural Strength, ASTM D790 22,000 psi 150 MPa 25,400 psi 175 MPa
Flexural Modulus, ASTM D790 5.6 x 10
5
psi 3,800 MPa 11.0 x 10
5
psi 7,586 MPa
Tensile Strength, ASTM D638 13,000 psi 89 MPa 13,900 psi 85.8 MPa
Tensile Modulus, ASTM D638 5.1 x 10
5
psi 3,500 MPa 12.8 x 10
5
psi 8,828 MPa
Tensile Elongation, ASTM D638 6.4 % 6.4 % 1.4 % 1.4 %
Barcol Hardness, 934-1 gauge, ASTM D2583 34 34 44-48 44-48
Heat Distortion Temperature, ASTM D648 220 F 104 C -- F -- C
* Gel time and reactivity will vary due to the type and concentration of Free Radical Initiator (catalyst), shop temperature, humidity, and type of fillers used. In order to meet
your individual needs, consult our technical sales representative for assistance. If using methyl ethyl ketone peroxide (MEKP) to gel and cure CoREZYN vinyl ester resins,
we recommend only these three brands: Cadox L-50a (Nouryon); Luperox DHD-9 (Arkema); and Norox MEKP-925 (United Initiators). These must be used at the
appropriate percentage and suitable temperature. Contact your Interplastic Corporation representative for assistance.
FLAME TEST PROPERTIES
Thickness 1/8 inch (3.2 mm) Laminate
Construction 4 Plies 1.5 oz/ft
2
, 33% Glass Mat
ASTM D635, Horizontal Burn Rate < 1
ASTM E84, Flame Spread 25
UL 94 **This is not to imply UL warranty (V-O) (HB < 1 ) (5V Pass)
HLT 15 100
CORVE8401D
Fire Retardant Vinyl Ester Resin
Technical Data Sheet
by | Sep 27, 2025
Interplastic Corporation makes no warranties regarding any material and/or samples described in this report. All properties
specified above are approximate and may vary from material delivered. Delivered material complies with the certificate of
analysis on each shipment of product. Interplastic Corporation makes no representations of fact regarding the material
except those specified above. Final determination of part or application and the suitability of the material for the use
contemplated is the sole responsibility of the buyer. Our technical sales representatives will assist in developing procedures
to fit individual requirements as a customer accommodation, but all advice is accepted at your risk and should be checked for
suitability to your particular processes and needs. These test data and properties are based on results obtained for a specific
material under the specified test conditions – they are not to be used as specifications and are not warranted as performance
attributes for any product or system.
INTERPLASTIC CORPORATION
2015 Northeast Broadway Street
Minneapolis, Minnesota 55413-1775
651.481.6860 Fax 612.331.4235
www.interplastic.com
Revised: 7/20
CORVE8190 is a promoted, thixotropic, corrosion resistant, epoxy vinyl ester resin for use in the manufacture of liner pipe
using cured-in-place techniques. The corrosion resistance of this resin is comparable to that of CORVE8100. Data on any
specific testing or corrosion recommendations will be supplied upon request.
FEATURES BENEFITS
Moderate Composite Exotherm Resistant to distortion during cure cycle
Fast Cure Time Shorter cycle times and fast hardness development
Good Fiberglass Wet-Out High composites physical properties
Tested Under ASTM D2990 for Flexural Modulus
Creep
Retains structural integrity under load in severe
conditions
LIQUID PROPERTIES RESULTS
Viscosity, Brookfield Model RV #4 Spindle @ 20 rpm, 77 F (25 C), cPs 2,000-4,000
Thixotropic Index 2.9-3.9
Gel Time run in a 140 F (60 C) water bath, initiated with 1.0 phr of Perkadox
16 and 0.5 phr of Trigonox C *
Gel Time, 130 F to 150 F (54-66 C), min:sec 10:00-20:00
Gel to Peak, 150 F (66 C) to Peak Exotherm Time, min:sec 2:00-10:00
Peak Exotherm 310-400 F (154-204 C)
Non-Volatile Content, % 58.0-66.0
Room Temperature Catalyzed Stability, hours >24
Specific Gravity 1.05-1.08
TYPICAL PROPERTIES
Thickness 1/8 inch (3.2 mm) Casting 1/4 inch (6.4 mm) Laminate
Construction Not Applicable CIPP Felt Laminate
Flexural Strength, ASTM D790 19,100 psi 132 MPa 11,000 psi 76 MPa
Flexural Modulus, ASTM D790 4.7 x 10
5
psi 3,241 MPa 5.1 x 10
5
psi 3,500 MPa
Tensile Strength, ASTM D638 11,000 psi 76 MPa 6,800 psi 47 MPa
Tensile Modulus, ASTM D638 4.6 x 10
5
psi 3,172 MPa 5.3 x 10
5
psi 3,700 MPa
Tensile Elongation, ASTM D638 4.2 % 4.2 % 2.0 % 2.0 %
Barcol Hardness, 934-1 gauge, ASTM D2583 36 36 N/A N/A
Heat Distortion Temperature, ASTM D648 215 F 102 C 197 F 92 C
* Gel time and reactivity will vary due to the type and concentration of Free Radical Initiator (catalyst), shop temperature, humidity, and type of fillers used. In order to meet
your individual needs, consult our technical sales representative for assistance. If using methyl ethyl ketone peroxide (MEKP) to gel and cure CoREZYN
vinyl ester resins
we recommend only these three brands: Cadox L-50a (Nouryon); Luperox DHD-9 (Arkema); and Norox MEKP-925 (United Initiators). These must be used at the
appropriate percentage and suitable temperature. Contact your Interplastic Corporation representative for assistance.
CORVE8190
Thixotropic Vinyl Ester Resin
Technical Data Sheet
