23M310400_TDS.pdf
TECHNICAL DATA SHEET
TDS #: MP55310
METHACRYLATE ADHESIVE
9411 Corsiar Road
Frankfort,IL 60423
1-800-552-0299
asisupport@instantca.com
DESCRIPTION:
METHACRYLATE ADHESIVE
WHAT THE MP SERIES BONDS:
MP55310 is a high performance two part methacrylate adhesive engineered
to bond a wide range of plastics, metals, and composite assemblies. It offers
outstanding bond strength, is extremely durable, with excellent impact and
weathering properties. MP55310 greatly increases the reliability of finished
assemblies with exceptional flexibility, it s ability to with stand extreme
temperature fluctuation and thermal cycling, and resistance to a wide range of
chemicals and environmental conditions.
PHYSICAL PROPERTIES (UNCURED):
ACTIVATOR 60,000
COLOR: OFF WHITE AMBER, GREY, OR BLACK
MIXED DENSITY:
8.20
VISCOSITY @ 25
0
C (cps): RESIN 60,000
MIX RATIO: VOLUME 1 TO 1
WEIGHT 1 TO 1
THIX INDEX: 5
FLASH POINT: 51
0
F
PHYSICAL PROPERTIES (CURED):
STRENGTH (PSI): SHEAR 3000-3500
TENSILE 3000-3500
WORK TIME: 10 MINUTES
HANDLING STRENGTH: 30 MINUTES
GAP FILL: .125 INCHES
TEMPERATURE RANGE: -67
0
F – +250
0
F
METALS
*ALUMINUM
*STEEL
*STAINLESS
*COATED METALS
THERMO SETS
*FIBERGLASS
*PHENOLICS
*GEL COATS
*EPOXY
*RIM URETHANE
*POLYURETHANE
*LIQUID MOLDING RESINS
THERMO PLASTICS
*ACRYLICS
*ABS
*POLYCARBONATES
*NYLONS
*PPO s
*VINYL’S
*PVC s
*STYRENE’S
*PEEK s
*PBT BLENDS
*PET BLENDS
BENEFITS:
>NO SURFACE PREP
>EXCELLENT STRENGTH
>IMPACT R
ESISTANT
>100% R
EACTIVE
>ROOM TEMPERATURE CURE
>EASILY A
PPLIED
PACKAGING:
The MP 55310 Series is conveniently packaged in 50 mil, 400 mil, pail, and drum kits.
Special
packaging is available upon request.
EFFECTS OF TEMPERATURE:
The product is best used at temperatures between 65
0
F and 80
0
F. Temperatures below 65
0
F
will slow the cure speed of the material and viscosities will be highe r. Temperatures above 80
0
F
will cause the material to cure faster and viscosities will be lower. For consistent dispensing
maintain temperature in the above mentioned range.
STORAGE AND SHELF LIFE:
The shelf life of the MP55300 Series for most products is one y ear from date of shipment
(check with ASI). Shelf life is based on the products being stored properly at temperatures
between 55
0
F and 75
0
F. Exposure to temperatures above 75
0
F will reduce the shelf life of
these materials.
PRECAUTIONS:
ASI s MP55300 Series products are flammable. Keep away from heat, spark, and open
flames.
KEEP OUT OF REACH OF CHILDREN. THE PRODUCT IS FOR INDUSTRIAL USE ONLY.
Keep containers closed when not in use. Avoid contact with skin and eyes. Harmful if
swallowed. Refer to Material Safety Data Sheet for complete safety information.
HANDLING AND CLEAN-UP:
For optimum bond strength and to insure maximum performance in the finished assembly
mate parts together within the specified work time of the adhesive. Make sure the bond
joint has uniform coverage and that a sufficient amount of adhesive is in the bond area. It
is important to have the adhesive applied, parts aligned and positioned, within the
established work times for the product. To ensure maximum performance in the finished
assembly parts should remain undisturbed until the fixture time is reached.
Clean up is best before the adhesive has cured. Cleaners containing NMP (N-methyl
pyrolidone) or Citrus terpene provide the best results. On cured adhesive repeat use may
be required.
Revised 2/20/2014
NON WARRANTY:
Information contained herein is based on tests we believe to be reliable and accurate. It is offered in good faith for the benefit of the
consumer. The Company shall not be liable for any injury, loss, or damage in the use of its chemical products since conditions or use
are beyond our control. In every case we urge and recommend the user conduct tests to determine to their own satisfaction that the
product is of acceptable quality and suitable for their particular purpose under their own operating conditions. Statements concerning
the possible use of our products are not intended as recommendations to use our products in the infringement of any patent. These
products are for industrial use only.
23M30550_TDS.pdf
23M310400A_TDS.pdf
23M30050S_TDS.pdf
STRENGTH (PSI): SHEAR >2500
TENSILE >2500
WORK TIME: 4 MINUTES
VISCOSITY @ 25
0
C (cps): RESIN 60,000
ACTIVATOR 60,000
COLOR:
MIXED DENSITY:
OFF WHITE
8.20
AMBER.SHELL
9411 Corsair Road
Frankfort, IL 60423
1-800-552-0299
asisupport@instantca.com
TECHNICAL DATA SHEET
TDS #MP55300
METHACRYLATE ADHESIVE
DESCRIPTION:
METHACRYLATE ADHESIVE
WHAT THE MP SERIES BONDS:
MP55300 is a high performance two part methacrylate adhesive engineered
to bond a wide range of plastics, metals, and composite assemblies. It offers
outstanding bond strength, is extremely durable, with excellent impact and
weathering properties. MP55300 greatly increases the reliability of finished
assemblies with exceptional flexibility, it s ability to withstand extreme
temperature fluctuation and thermal cycling, and resistance to a wide range of
chemicals and environmental conditions. It offers exceptional bonding to
a wide range of substrates.
PHYSICAL PROPERTIES (UNCURED):
MIX RATIO: VOLUME 1 TO 1
WEIGHT 1 TO 1
THIX INDEX: 5
FLASH POINT: 51
0
F
PHYSICAL PROPERTIES (CURED):
HANDLING STRENGTH: 10 MINUTES
GAP FILL:UP TO .125 INCH
TEMPERATURE RANGE: -67
0
F – +250
0
F
METALS
*ALUMINUM
*STEEL
*STAINLESS
*COATED METALS
THERMO SETS
*FIBERGLASS
*PHENOLICS
*GEL COATS
*EPOXY
*RIM URETHANE
*POLYURETHANE
*LIQUID MOLDING RESINS
THERMO PLASTICS
*ACRYLICS
*ABS
*POLYCARBONATES
*NYLONS
*PPO s
*VINYL’S
*PVC s
*STYRENE’S
*PEEK s
*PBT BLENDS
*PET BLENDS
BENEFITS:
>NO SURFACE PREP
>EXCELLENT STRENGTH
>IMPACT RESISTANT
>100% REACTIVE
>ROOM TEMPERATURE CURE
>EASILY APPLIED
PACKAGING:
The MP 55300 Series is conveniently packaged in 50 mil, 400 mil, pail, and drum kits. Special
packaging is available upon request.
EFFECTS OF TEMPERATURE:
The product is best used at temperatures between 65
0
F and 80
0
F. Temperatures below 65
0
F
will slow the cure speed of the material and viscosities will be higher. Temperatures above 80
0
F
will cause the material to cure faster and viscosities will be lower. For consistent dispensing
maintain temperature in the above mentioned range.
STORAGE AND SHELF LIFE:
The shelf life of the MP55300 Series for most products is one year from date of shipment (check
with ASI). Shelf life is based on the products being stored properly at temperatures between 55
0
F and 75
0
F. Exposure to temperatures above 75
0
F will reduce the shelf life of these materials.
PRECAUTIONS:
ASI s MP55300 Series products are flammable. Keep away from heat, spark, and open flames.
KEEP OUT OF REACH OF CHILDREN. THE PRODUCT IS FOR INDUSTRIAL USE ONLY. Keep
containers closed when not in use. Avoid contact with skin and eyes. Harmful if swallowed.
Refer to Material Safety Data Sheet for complete safety information.
HANDLING AND CLEAN-UP:
For optimum bond strength and to insure maximum performance in the finished assembly mate
parts together within the specified work time of the adhesive. Make sure the bond joint has
uniform coverage and that a sufficient amount of adhesive is in the bond area. It is important to
have the adhesive applied, parts aligned and positioned, within the established work times for the
product. To ensure maximum performance in the finished assembly parts should remain
undisturbed until the fixture time is reached.
Clean up is best before the adhesive has cured. Cleaners containing NMP (N-methyl pyrolidone)
or Citrus terpene provide the best results. On cured adhesive repeat use may be required.
NON WARRANTY:
Information contained herein is based on tests we believe to be reliable and accurate. It is offered in good faith for the benefit of the consumer. The
Company shall not be liable for any injury, loss, or damage in the use of its chemical products since conditions or use are beyond our control. In
every case we urge and recommend the user conduct tests to determine to their own satisfaction that the product is of
acceptable quality and suitable for their particular purpose under their own operating conditions. Statements concerning the possible use
of our products are not intended as recommendations to use our products in the infringement of any patent. These products are for industrial use
only.
23M300400S_TDS.pdf
STRENGTH (PSI): SHEAR >2500
TENSILE >2500
WORK TIME: 4 MINUTES
VISCOSITY @ 25
0
C (cps): RESIN 60,000
ACTIVATOR 60,000
COLOR:
MIXED DENSITY:
OFF WHITE
8.20
AMBER.SHELL
9411 Corsair Road
Frankfort, IL 60423
1-800-552-0299
asisupport@instantca.com
TECHNICAL DATA SHEET
TDS #MP55300
METHACRYLATE ADHESIVE
DESCRIPTION:
METHACRYLATE ADHESIVE
WHAT THE MP SERIES BONDS:
MP55300 is a high performance two part methacrylate adhesive engineered
to bond a wide range of plastics, metals, and composite assemblies. It offers
outstanding bond strength, is extremely durable, with excellent impact and
weathering properties. MP55300 greatly increases the reliability of finished
assemblies with exceptional flexibility, it s ability to withstand extreme
temperature fluctuation and thermal cycling, and resistance to a wide range of
chemicals and environmental conditions. It offers exceptional bonding to
a wide range of substrates.
PHYSICAL PROPERTIES (UNCURED):
MIX RATIO: VOLUME 1 TO 1
WEIGHT 1 TO 1
THIX INDEX: 5
FLASH POINT: 51
0
F
PHYSICAL PROPERTIES (CURED):
HANDLING STRENGTH: 10 MINUTES
GAP FILL:UP TO .125 INCH
TEMPERATURE RANGE: -67
0
F – +250
0
F
METALS
*ALUMINUM
*STEEL
*STAINLESS
*COATED METALS
THERMO SETS
*FIBERGLASS
*PHENOLICS
*GEL COATS
*EPOXY
*RIM URETHANE
*POLYURETHANE
*LIQUID MOLDING RESINS
THERMO PLASTICS
*ACRYLICS
*ABS
*POLYCARBONATES
*NYLONS
*PPO s
*VINYL’S
*PVC s
*STYRENE’S
*PEEK s
*PBT BLENDS
*PET BLENDS
BENEFITS:
>NO SURFACE PREP
>EXCELLENT STRENGTH
>IMPACT RESISTANT
>100% REACTIVE
>ROOM TEMPERATURE CURE
>EASILY APPLIED
PACKAGING:
The MP 55300 Series is conveniently packaged in 50 mil, 400 mil, pail, and drum kits. Special
packaging is available upon request.
EFFECTS OF TEMPERATURE:
The product is best used at temperatures between 65
0
F and 80
0
F. Temperatures below 65
0
F
will slow the cure speed of the material and viscosities will be higher. Temperatures above 80
0
F
will cause the material to cure faster and viscosities will be lower. For consistent dispensing
maintain temperature in the above mentioned range.
STORAGE AND SHELF LIFE:
The shelf life of the MP55300 Series for most products is one year from date of shipment (check
with ASI). Shelf life is based on the products being stored properly at temperatures between 55
0
F and 75
0
F. Exposure to temperatures above 75
0
F will reduce the shelf life of these materials.
PRECAUTIONS:
ASI s MP55300 Series products are flammable. Keep away from heat, spark, and open flames.
KEEP OUT OF REACH OF CHILDREN. THE PRODUCT IS FOR INDUSTRIAL USE ONLY. Keep
containers closed when not in use. Avoid contact with skin and eyes. Harmful if swallowed.
Refer to Material Safety Data Sheet for complete safety information.
HANDLING AND CLEAN-UP:
For optimum bond strength and to insure maximum performance in the finished assembly mate
parts together within the specified work time of the adhesive. Make sure the bond joint has
uniform coverage and that a sufficient amount of adhesive is in the bond area. It is important to
have the adhesive applied, parts aligned and positioned, within the established work times for the
product. To ensure maximum performance in the finished assembly parts should remain
undisturbed until the fixture time is reached.
Clean up is best before the adhesive has cured. Cleaners containing NMP (N-methyl pyrolidone)
or Citrus terpene provide the best results. On cured adhesive repeat use may be required.
NON WARRANTY:
Information contained herein is based on tests we believe to be reliable and accurate. It is offered in good faith for the benefit of the consumer. The
Company shall not be liable for any injury, loss, or damage in the use of its chemical products since conditions or use are beyond our control. In
every case we urge and recommend the user conduct tests to determine to their own satisfaction that the product is of
acceptable quality and suitable for their particular purpose under their own operating conditions. Statements concerning the possible use
of our products are not intended as recommendations to use our products in the infringement of any patent. These products are for industrial use
only.
23M300322N_TDS.pdf
23HP300-15_TDS.pdf
23FX483233_TDS.pdf
PDS-SP 4832-5-0718 1
SP 4832
MONO-COMPONENT EPOXY SYSTEM
INTRODUCTION
SP 4832 is a highly thixotropic, gap filling paste. It is a single component epoxy system designed to co-cure at
moderate elevated temperature with Gurit s SE prepregs. The product is designed to be either applied between gel
coat and prepreg in sharp recesses in order to bridge any large gaps between the two, or used as a highly effective
low density core splicing adhesive. The colour is a very dark grey, to tone in with carbon prepregs.
2 PDS-SP 4832-5-0718
INSTRUCTIONS FOR USE
MIXING & HANDLING
SP 4832 resin is a pre-catalysed, mono-component system and
therefore does not need to be mixed with another component.
Because it is pre-catalysed, care should be taken with storage
and handling. The system requires a temperature of 80 C to
cure fully but some polymerisation, which will thicken the
product and affect its handling properties, can occur at lower
temperatures. To ensure safe use the product should not be
used for a long time or stored at ambient temperatures above
40 C.
For long term storage, the product should be stored at -18 C in
a freezer, but it can be kept at room temperature (20 C) for up
to 20 days without affecting the handling and cured properties
too much. If stored in freezer conditions, the product should be
warmed to ambient temperature before dispensing. It should
be returned to the freezer immediately after use.
APPLICATION
The adhering surfaces should be dry, free of grease, oil, or
mould release or similar material, which would prevent
adhesion of the system. The pre-mixed system is available in
cartridges that fit a standard mastic gun, or it can be applied by
pallet knife or by a suitable dispensing/injection system. The
polymerisation reaction of the system does not generate
significant amounts of heat but in a controlled manner without
runaway exotherm and so large volumes in thicknesses up to
25mm can be applied safely.
SP 4832 is resistant to sag even in thicknesses up to 20-25mm
on a vertical surface. It retains its outstanding thixotropy even
at elevated temperature.
CURING
The system is designed to co-cure with Gurit s SE prepregs /
SPRINT
Materials.
A typical cure cycle is 12 hours at 80 C. Other cure times &
temperatures are possible but no data has been determined for
these alternative cure cycles. Exact times for any particular set
of conditions have not been determined and users should
satisfy themselves that adequate properties for the system are
obtained for the particular combination of mixed volume, cure
temperature, and elapsed time.
PROPERTIES
Physical properties
Resin appearance dark grey paste
Resin viscosity (@ 25 C) 750 P – 950 P
Resin density (@ 25 C) 0.66-0.70g/cc
Sag resistance t.b.a.
Cured density 0.66-0.72
Tg1 DMTA (12 hours/80 C) 86 C
Tg2 DMTA (12 hours/80 C) 99 C
Peak exotherm 124 C (1 C/min to 80 C; 12 hrs at 80 C)
Bond Strength to Nomex Honeycomb
node orientation t.b.a. N/mm2
ribbon orientation t.b.a. N/mm2
Bond strength to P1200 Corecell 3.01 N/mm2 (flat wise tensile)
PDS-SP 4832-5-0718 3
HEALTH AND SAFETY
The following points must be considered:
1. Skin contact must be avoided by wearing protective gloves.
Gurit recommends the use of disposable nitrile gloves for most
applications. The use of barrier creams is not recommended,
but to preserve skin condition a moisturising cream should be
used after washing.
2. Overalls or other protective clothing should be worn when
mixing, laminating or sanding. Contaminated work clothes
should be thoroughly cleaned before re-use.
3. Eye protection should be worn if there is a risk of resin,
hardener, solvent or dust entering the eyes. If this occurs flush
the eye with water for 15 minutes, holding the eyelid open, and
seek medical attention.
4. Ensure adequate ventilation in work areas. Respiratory
protection should be worn if there is insufficient ventilation.
Solvent vapours should not be inhaled as they can cause
dizziness, headaches, loss of consciousness and can have long
term health effects.
5. If the skin becomes contaminated, then the area must be
immediately cleansed. The use of resin-removing cleansers is
recommended. To finish, wash with soap and warm water.
The use of solvents on the skin to remove resins etc must be
avoided.
Washing should be part of routine practice:
nbefore eating or drinking
nbefore smoking
nbefore using the lavatory
nafter finishing work
6. The inhalation of sanding dust should be avoided and if it
settles on the skin then it should be washed off. After more
extensive sanding operations a shower/bath and hair wash is
advised.
Gurit produces a separate full Safety Data Sheet for all
hazardous products. Please ensure that you have the correct
SDS to hand for the materials you are using before
commencing work. A more detailed guide for the safe use of
Gurit resin systems is also available from Gurit and can be
found on our website at www.gurit.com
APPLICABLE RISK & SAFETY
PHRASES
Please refer to product SDS for up to date information specific
to this product.
4 PDS-SP 4832-5-0718
TRANSPORT & STORAGE
SP 4832 contains resin, hardener and catalyst components. It is relatively latent at room
temperature but can represent a hazard if subjected to excessive heat (>40 C). The
material should ideally be transported frozen and should be stored at -18 C. Its shelf life at
-18 C is 24 months.
SP 4832 should be kept in a secured closed container (max. 25 kg) during transport and
storage. Any accidental spillage should be soaked up with sand, sawdust, cotton waste or
any other absorbent material. The area should then be washed clean (see appropriate
Safety Data Sheet).
NOTICE
All advice, instruction or recommendation is given in good faith but the selling Gurit entity (the
Company) only warrants that advice in writing is given with reasonable skill and care. No further duty
or responsibility is accepted by the Company. All advice is given subject to the terms and conditions
of sale (the Conditions) which are available on request from the Company or may be viewed at
Gurit s Website: www.gurit.com/terms-and-conditions.aspx
The Company strongly recommends that Customers make test panels in the final process
conditions and conduct appropriate testing of any goods or materials supplied by the Company prior
to final use to ensure that they are suitable for the Customer s planned application. Such testing
should include testing under conditions as close as possible to those to which the final component
may be subjected. The Company specifically excludes any warranty of fitness for purpose of the
goods other than as set out in writing by the Company. Due to the varied nature of end-use
applications, the Company does, in particular, not warrant that the test panels in the final process
conditions and/or the final component pass any fire standards.
The Company reserves the right to change specifications and prices without notice and Customers
should satisfy themselves that information relied on by the Customer is that which is currently
published by the Company on its website. Any queries may be addressed to the Technical Services
Department.
Gurit is continuously reviewing and updating literature. Please ensure that you have the current
version by contacting your sales contact and quoting the revision number in the bottom left-hand
corner of this page.
TECHNICAL CONTACT INFORMATION
For all other enquiries such as technical queries:
Telephone + 44 1983 828000 (08:30 17:00 GMT)
Email technical.support@gurit.com
24-HOUR CHEMICAL EMERGENCY NUMBER
For advice on chemical emergencies, spillages, fires or exposures:
Europe +44 1273 289451
Americas +1 646 844 7309
APAC +65 3158 1412
Ecustomer.support@gurit.com
Wwww.gurit.com
23FP228532-D_TDS.pdf
Interplastic Corporation makes no warranties regarding any material and/or samples described in this report. All properties
specified above are approximate and may vary from material delivered. Delivered material complies with the certificate of
analysis on each shipment of product. Interplastic Corporation makes no representations of fact regarding the material
except those specified above. Final determination of part or application and the suitability of the material for the use
contemplated is the sole responsibility of the buyer. Our technical sales representatives will assist in developing procedures
to fit individual requirements as a customer accommodation, but all advice is accepted at your risk and should be checked for
suitability to your particular processes and needs. These test data and properties are based on results obtained for a specific
material under the specified test conditions – they are not to be used as specifications and are not warranted as performance
attributes for any product or system.
INTERPLASTIC CORPORATION
2015 Northeast Broadway Street
Minneapolis, Minnesota 55413-1775
651.481.6860 Fax 612.331.4235
www.interplastic.com
Revised: 8/2022
PF-228-532 is a fiberglass-reinforced polyester fillet putty. It is designed specifically for bonding FRP parts and
forming contours that require added reinforcement. This putty offers excellent adhesion and shear strength. PF-228-
532 may be used for general bonding and to fill cracks, corners, and angles where reinforcement is needed.
FEATURES BENEFITS
Strong and Tough Adhesive Excellent adhesion to FRP
Good Hydrolytic Stability Long life, especially in marine applications
Void-Free Consistency, Minimizing Air Entrapment Does not have weak spots due to voids
Reinforced Excellent impact resistance
LIQUID PROPERTIES RESULTS
Viscosity @ 77 F (25 C), Brookfield RV T-E Spindle @ 5 rpm, cPs 340,000
100 grams compound @ 77 F (25 C), initiated with 2% L-50A by weight*
Gel Time, minutes 13
Percent HAPs (Styrene) 22
HAPs Content, lbs/gallon 2.0
Weight per Gallon @ 77 F (25 C), lbs 9.0
Specific Gravity @ 77 F (25 C) 1.08
* Gel time and reactivity will vary due to the type and concentration of Free Radical Initiator (catalyst), shop
temperature, humidity, and type of fillers used. In order to meet your individual needs, consult our technical sales
representative for assistance.
Application: PF-228-532 may be used for general bonding and to fill cracks, corners, and angles where
reinforcement is required. There can be issues with achieving a good bond to highly cured gel coat and gel coated
parts. In cases where the gel coat is over a month old, has been post-cured, or could otherwise be highly cured, the
user should test for adequate adhesion and may need to sand and clean the part before applying the adhesive
material.
Storage and Handling: PF-228-532 should be properly stored in closed, opaque containers at temperatures not
exceeding 77 F (25 C). Store only in original containers. To avoid decomposition keep away from direct sunlight and
excess heat. Refer to the Safety Data Sheet for further details on safety and storage.
PF-228-532
COR-Grip Fillet Compound
Technical Data Sheet