PRODUCT SPECIFICATION SHEET
Customer : CFA Mills
Date : October 5
th
, 2023
PARA ARAMID FILAMENT YARN
Construction : Den 1000/F665
Color : Natural
Code : H01.150
Properties specifications
______________________________________________________
Linear density (Den) 1000 (+/- 30)
Tenacity (gr/Den) 23.0 (+/- 2.0)
Elongation at break (%) 3.60 (+/- 1.0)
The above mentioned information is given in good faith but without any warranty
SHD COMPOSITE MATERIALS INC
203 McKenzie Road
Mooresville
NC 28117
www.shdcomposites.com
Tel: +1 (704) 6266876
us-sales@shdcomposites.com
SHDUS/MISC/945 Issue: 1 21st June 2022
Revised: 23
rd
January 2018 Uncontrolled copy when printed
LTC250-2XL
Epoxy Component Prepreg
Introduction
LTC250-2XL Prepreg is designed to cure at low temperatures whilst giving you increased outlife over other
low-cure systems and great flexibility in component manufacture. It is a toughened epoxy resin system that
can be supplied on a variety of fabrics to meet your cost and manufacturing requirements.
Typical applications: General purpose Visual
Key Features & Benefits
Cure temperature from 120 F to 170 F
Service temperature up to 260 F after post cure
Low CTE and shrinkage
Work life at 70 F: 5 days
Storage life at 0 F: 12 months
Very low VOC content no added solvents during manufacture
Storage & Out Life
This material should be kept frozen at 0 F. It must be kept sealed in a polythene bag which must not be
opened until fully thawed to room temperature. If the material is not fully used, then the material must be
resealed in the polythene bag to prevent moisture absorption.
SHD COMPOSITE MATERIALS INC
203 McKenzie Road
Mooresville
NC 28117
www.shdcomposites.com
Tel: +1 (704) 6266876
us-sales@shdcomposites.com
SHDUS/MISC/945 Issue: 1 21st June 2022
Revised: 23
rd
January 2018 Uncontrolled copy when printed
Cure Cycles & performances
Recommended Initial cure: 140 F for 14h, at a ramp rate of 2 F/min
Recommended Post cure: 250 F for 1h, at a ramp rate of 2 F/min
Cure Initial Min Cure Tg
120 F (minimum) 40 hours 130 F
140 F 14 hours 150 F
150 F 8 hours 160 F
170 F (maximum) 4 hours 175 F
250 F Post cure 1 hours 265 F
Curing Schedule is meant to be a guide only and is subject to local conditions.
To avoid exotherm particular care must be taken with thick laminates.
Ramp rates must not exceed 5 F per minute during initial cure.
Ramp rates must not exceed 1 F per minute during post cure (free standing).
Volatile content < 1.0% Fibre volume fraction 50 to 60% Voidage (autoclave cure) < 1.0% Cured Material Properties Test Results Standard DMA Tg Storage Modulus Onset 266 F ASTM D7028 Tg Tan Peak 291 F Data obtained after a 250 F, 1h post cure. SHD COMPOSITE MATERIALS INC 203 McKenzie Road Mooresville NC 28117 www.shdcomposites.com Tel: +1 (704) 6266876 us-sales@shdcomposites.com SHDUS/MISC/945 Issue: 1 21st June 2022 Revised: 23 rd January 2018 Uncontrolled copy when printed Viscosity Profile Health and Safety This material contains epoxy resin which can cause allergic reactions with skin contact and must avoid repeated and prolonged skin contact. Please refer to the product Safety Data Sheet before using this material. The following precautions must be taken when using epoxy resin prepregs: Overalls must be worn. Impervious gloves must be worn. Curing schedule is meant to be as a guide only and is subject to local conditions. To avoid exotherm, particular care must be taken with thick laminates. Ramp rates must not exceed 5 F/min during initial cure and 1 F/min during post cure. Disclaimer: Technical advice, instruction, data or recommendation, whether verbal or in writing, is given in good faith. The SHD company providing any such advice gives no warranty or guarantee, whether express or implied, in relation to such advice. Customers must carry out their own tests and assessments as necessary in order to determine the quality and suitability of the product for their particular application and circumstances. Such testing should be performed under conditions identical to those to which the final component/product may be subjected. Values listed in any SHD document are for typical properties of the product or substance in question and are not intended to be used in establishing either statistical specifications nor engineering basis values. They do not constitute either minimum or maximum values for the product or substance in question. 1 10 100 1000 10000 100000 1000000 10000000 20 40 60 80 100 120 140 Pa.s C LTC250-2XLViscosity Profile
SHD COMPOSITE MATERIALS INC
203 McKenzie Road
Mooresville
NC 28117
www.shdcomposites.com
Tel: +1 (704) 6266876
us-sales@shdcomposites.com
SHDUS/MISC/945 Issue: 1 21st June 2022
Revised: 23
rd
January 2018 Uncontrolled copy when printed
LTC250-2XL
Epoxy Component Prepreg
Introduction
LTC250-2XL Prepreg is designed to cure at low temperatures whilst giving you increased outlife over other
low-cure systems and great flexibility in component manufacture. It is a toughened epoxy resin system that
can be supplied on a variety of fabrics to meet your cost and manufacturing requirements.
Typical applications: General purpose Visual
Key Features & Benefits
Cure temperature from 120 F to 170 F
Service temperature up to 260 F after post cure
Low CTE and shrinkage
Work life at 70 F: 5 days
Storage life at 0 F: 12 months
Very low VOC content no added solvents during manufacture
Storage & Out Life
This material should be kept frozen at 0 F. It must be kept sealed in a polythene bag which must not be
opened until fully thawed to room temperature. If the material is not fully used, then the material must be
resealed in the polythene bag to prevent moisture absorption.
SHD COMPOSITE MATERIALS INC
203 McKenzie Road
Mooresville
NC 28117
www.shdcomposites.com
Tel: +1 (704) 6266876
us-sales@shdcomposites.com
SHDUS/MISC/945 Issue: 1 21st June 2022
Revised: 23
rd
January 2018 Uncontrolled copy when printed
Cure Cycles & performances
Recommended Initial cure: 140 F for 14h, at a ramp rate of 2 F/min
Recommended Post cure: 250 F for 1h, at a ramp rate of 2 F/min
Cure Initial Min Cure Tg
120 F (minimum) 40 hours 130 F
140 F 14 hours 150 F
150 F 8 hours 160 F
170 F (maximum) 4 hours 175 F
250 F Post cure 1 hours 265 F
Curing Schedule is meant to be a guide only and is subject to local conditions.
To avoid exotherm particular care must be taken with thick laminates.
Ramp rates must not exceed 5 F per minute during initial cure.
Ramp rates must not exceed 1 F per minute during post cure (free standing).
Volatile content < 1.0% Fibre volume fraction 50 to 60% Voidage (autoclave cure) < 1.0% Cured Material Properties Test Results Standard DMA Tg Storage Modulus Onset 266 F ASTM D7028 Tg Tan Peak 291 F Data obtained after a 250 F, 1h post cure. SHD COMPOSITE MATERIALS INC 203 McKenzie Road Mooresville NC 28117 www.shdcomposites.com Tel: +1 (704) 6266876 us-sales@shdcomposites.com SHDUS/MISC/945 Issue: 1 21st June 2022 Revised: 23 rd January 2018 Uncontrolled copy when printed Viscosity Profile Health and Safety This material contains epoxy resin which can cause allergic reactions with skin contact and must avoid repeated and prolonged skin contact. Please refer to the product Safety Data Sheet before using this material. The following precautions must be taken when using epoxy resin prepregs: Overalls must be worn. Impervious gloves must be worn. Curing schedule is meant to be as a guide only and is subject to local conditions. To avoid exotherm, particular care must be taken with thick laminates. Ramp rates must not exceed 5 F/min during initial cure and 1 F/min during post cure. Disclaimer: Technical advice, instruction, data or recommendation, whether verbal or in writing, is given in good faith. The SHD company providing any such advice gives no warranty or guarantee, whether express or implied, in relation to such advice. Customers must carry out their own tests and assessments as necessary in order to determine the quality and suitability of the product for their particular application and circumstances. Such testing should be performed under conditions identical to those to which the final component/product may be subjected. Values listed in any SHD document are for typical properties of the product or substance in question and are not intended to be used in establishing either statistical specifications nor engineering basis values. They do not constitute either minimum or maximum values for the product or substance in question. 1 10 100 1000 10000 100000 1000000 10000000 20 40 60 80 100 120 140 Pa.s C LTC250-2XLViscosity Profile
PRODUCT SHEET
SUPERFLEX WEB
MARKETS
Automotive
Marine &
Comp
Wood
Other
Markets
TYPE
DRY
WET
APPLICATION SUGGESTIONS
Sanding for Blending
Micro-finishing / Rectifying
FEATURES BENEFITS
Abrasive impregnated
web
>
Consistent scratch pattern
Web construction >
Prevents oversanding
High Flexibility >
Adaptable to curves &
contoured Surfaces
SUBSTRACTS
Primers
Top Coats
Clear Coats
Fibre Glass
Gel Coat
Metal
Wood Coatings
Page 1/2 – Printed in 2017-10-06
PRODUCT SHEET
SUPERFLEX WEB
FASTENING SYSTEM / BACKING PAD
PRODUCT SPECIFICATIONS
Backing ColourForm Abrasive Grit
Abrasive Impregnated thin Nylon WebMaroon Pad Aluminium Oxide 360-400
Abrasive Impregnated thin Nylon Web Grey Pad Silicon Carbide 1000-1500
Page 2/2 – Printed in 2017-10-06
PRODUCT SHEET
SUPERFLEX WEB
MARKETS
Automotive
Marine &
Comp
Wood
Other
Markets
TYPE
DRY
WET
APPLICATION SUGGESTIONS
Sanding for Blending
Micro-finishing / Rectifying
FEATURES BENEFITS
Abrasive impregnated
web
>
Consistent scratch pattern
Web construction >
Prevents oversanding
High Flexibility >
Adaptable to curves &
contoured Surfaces
SUBSTRACTS
Primers
Top Coats
Clear Coats
Fibre Glass
Gel Coat
Metal
Wood Coatings
Page 1/2 – Printed in 2017-10-06
PRODUCT SHEET
SUPERFLEX WEB
FASTENING SYSTEM / BACKING PAD
PRODUCT SPECIFICATIONS
Backing ColourForm Abrasive Grit
Abrasive Impregnated thin Nylon WebMaroon Pad Aluminium Oxide 360-400
Abrasive Impregnated thin Nylon Web Grey Pad Silicon Carbide 1000-1500
Page 2/2 – Printed in 2017-10-06
PRODUCT SHEET
RHYNOGRIP
MARKETS
Automotive
Marine &
Comp
Wood
Other
Markets
FORMS
Disc
Delta
TYPE
DRY
APPLICATION SUGGESTIONS
Heavy Duty Sanding
Sanding / Preparation
FEATURES BENEFITS
Highly resistant backing>
Crease & tear resistant
High initial cutting action>
Rapid stock removal
High strength resin
bond
>
Minimal grit shedding
SUBSTRACTS
Old paint
Fillers
Primers
Fibre Glass
Gel Coat
Solid Surface
Metal Burrs & Welding
Seems
Metal
Hard Wood
Wooden Floors
Page 1/2 – Printed in 2017-10-06
PRODUCT SHEET
Grit 3640506080100120150180220320
Backing E wt Paper
Abrasive Aluminium Oxide
Bonding Modified Synthetic Resins
RHYNOGRIP
FASTENING SYSTEM / BACKING PAD
PRODUCT SPECIFICATIONS
Page 2/2 – Printed in 2017-10-06
PRODUCT SHEET
RHYNOGRIP
MARKETS
Automotive
Marine &
Comp
Wood
Other
Markets
FORMS
Disc
Delta
TYPE
DRY
APPLICATION SUGGESTIONS
Heavy Duty Sanding
Sanding / Preparation
FEATURES BENEFITS
Highly resistant backing>
Crease & tear resistant
High initial cutting action>
Rapid stock removal
High strength resin
bond
>
Minimal grit shedding
SUBSTRACTS
Old paint
Fillers
Primers
Fibre Glass
Gel Coat
Solid Surface
Metal Burrs & Welding
Seems
Metal
Hard Wood
Wooden Floors
Page 1/2 – Printed in 2017-10-06
PRODUCT SHEET
Grit 3640506080100120150180220320
Backing E wt Paper
Abrasive Aluminium Oxide
Bonding Modified Synthetic Resins
RHYNOGRIP
FASTENING SYSTEM / BACKING PAD
PRODUCT SPECIFICATIONS
Page 2/2 – Printed in 2017-10-06
PRODUCT SHEET
RHYNOSTICK
MARKETS
Automotive
Marine &
Comp
Wood
Building &
Deco
FORMS
Strip
Roll
Disc
TYPE
DRY
APPLICATION SUGGESTIONS
Heavy Duty Sanding
Sanding / Preparation
Fine Sanding
Sanding for Blending
FEATURES BENEFITS
High Flexibility >
Adaptable to curves &
contoured Surfaces
Uniformity of scratch
pattern
>
Optimum substrate
preparation
Clog resistant coating >
Long lasting sanding
Protective release paper>
Maximum adhesion to
backing pad
SUBSTRACTS
Old paint
Fillers
Primers
Top Coats
Clear Coats
Fibre Glass
Gel Coat
Soft and Resinous Wood
Wood Coatings
Walls and Dry Walls
Page 1/2 – Printed in 2017-10-06
PRODUCT SHEET
Lubricant Coating
Grit 4060 80100120 1501802202402803203604005006008001000
Backing (1) (2) B wt Latex Paper
Abrasive Aluminium Oxide
Bonding Modified Synthetic Resins
RHYNOSTICK
FASTENING SYSTEM / BACKING PAD
PRODUCT SPECIFICATIONS
(1) D wt Latex Paper
(2) C wt Latex Paper
Page 2/2 – Printed in 2017-10-06
PRODUCT SHEET
RHYNOSTICK
MARKETS
Automotive
Marine &
Comp
Wood
Building &
Deco
FORMS
Strip
Roll
Disc
TYPE
DRY
APPLICATION SUGGESTIONS
Heavy Duty Sanding
Sanding / Preparation
Fine Sanding
Sanding for Blending
FEATURES BENEFITS
High Flexibility >
Adaptable to curves &
contoured Surfaces
Uniformity of scratch
pattern
>
Optimum substrate
preparation
Clog resistant coating >
Long lasting sanding
Protective release paper>
Maximum adhesion to
backing pad
SUBSTRACTS
Old paint
Fillers
Primers
Top Coats
Clear Coats
Fibre Glass
Gel Coat
Soft and Resinous Wood
Wood Coatings
Walls and Dry Walls
Page 1/2 – Printed in 2017-10-06
PRODUCT SHEET
Lubricant Coating
Grit 4060 80100120 1501802202402803203604005006008001000
Backing (1) (2) B wt Latex Paper
Abrasive Aluminium Oxide
Bonding Modified Synthetic Resins
RHYNOSTICK
FASTENING SYSTEM / BACKING PAD
PRODUCT SPECIFICATIONS
(1) D wt Latex Paper
(2) C wt Latex Paper
Page 2/2 – Printed in 2017-10-06
PRODUCT SHEET
RHYNALOX/RHYNODRY PLUS
MARKETS
Automotive
Marine &
Comp
Other
Markets
FORMS
Sheets
TYPE
DRY
APPLICATION SUGGESTIONS
Heavy Duty Sanding
Sanding / Preparation
Fine Sanding
Sanding for Blending
Micro-finishing / Rectifying
FEATURES BENEFITS
High Flexibility >
Adaptable to curves &
contoured Surfaces
High initial cutting action>
Rapid stock removal
Uniformity of scratch
pattern
>
Optimum substrate
preparation
High strength resin bond>
Minimal grit shedding
Clog resistant coating >
Long lasting sanding
SUBSTRACTS
Old paint
Fillers
Primers
Top Coats
Clear Coats
Fibre Glass
Gel Coat
Metal
Hard Metal
Page 1/2 – Printed in 2017-10-06
PRODUCT SHEET
Lubricant Coating
Grit 80100120 150180220240320400600800100012001500
Backing D wt Paper B wt Latex Paper
Abrasive Aluminium Oxide
Bonding Modified Synthetic Resins
RHYNALOX/RHYNODRY PLUS
FASTENING SYSTEM / BACKING PAD
PRODUCT SPECIFICATIONS
Page 2/2 – Printed in 2017-10-06