by | Sep 27, 2025
TECHNICAL DATA SHEE T
STRETCH- VAC
2000
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS SV2000_0 2.21_Issue1
STRETCH- VAC 2000
Vacuum bagging film
Ideally suited to aerospace applications
Features and Benefits
Soft, co-extruded, ultra high elongation, multi layered
film, produced from a modified polyamide resin.
Easily conformable for complex contoured parts,
formulated to be less affected by environmental
changes and remains flexible in low humidity
conditions.
Recommended as a bagging film for advanced
composite fabrication, when a dependable,
conformable, soft, stretchable bag is required.
Fewer pleats are needed when vacuum bagging
either complex or simple contoured parts, due to its
unique characteristics.
Manufactured using advanced state-of-the-art
blown film technology.
Can be heat seamed to meet any custom shape
requirements.
PROPERTIES
Maximum use temperature 204 C 400 F
Color Red and transparent
Tensile strength at break (ASTM D882) 103.42 MPa 15000 PSI
Elongation at break (ASTM D882) 400%
Yield
50 m: 17.30m /kg
75 m: 11.60m /kg
9.39yd /lb
6.3yd /lb
AVAILABILITY
Thickness 50 and 75 m 0.002 and 0.003in
Roll weight Up to 45Kg Up to 100lb
Widths Up to 4.06m (open) Up to 160in (open)
Formats available Lay-flat tube, sheet, V sheet
STORAGE
Stretch-Vac 2000 is hydrophilic material. Moisture and water act as plasticizers. The level of moisture content at time of use
is therefore an important factor for successful performance. The higher the moisture content the more flexible they become.
Conversely at lower moisture levels flexibility is limited.
Do not store rolls vertically on their ends
TECHNICAL DATA SHEE T
STRETCH- VAC
2000
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS SV2000_0 2.21_Issue1
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
TECHNICAL DATA SHEE T
STRETCH- VAC
2000
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS SV2000_0 2.21_Issue1
STRETCH- VAC 2000
Vacuum bagging film
Ideally suited to aerospace applications
Features and Benefits
Soft, co-extruded, ultra high elongation, multi layered
film, produced from a modified polyamide resin.
Easily conformable for complex contoured parts,
formulated to be less affected by environmental
changes and remains flexible in low humidity
conditions.
Recommended as a bagging film for advanced
composite fabrication, when a dependable,
conformable, soft, stretchable bag is required.
Fewer pleats are needed when vacuum bagging
either complex or simple contoured parts, due to its
unique characteristics.
Manufactured using advanced state-of-the-art
blown film technology.
Can be heat seamed to meet any custom shape
requirements.
PROPERTIES
Maximum use temperature 204 C 400 F
Color Red and transparent
Tensile strength at break (ASTM D882) 103.42 MPa 15000 PSI
Elongation at break (ASTM D882) 400%
Yield
50 m: 17.30m /kg
75 m: 11.60m /kg
9.39yd /lb
6.3yd /lb
AVAILABILITY
Thickness 50 and 75 m 0.002 and 0.003in
Roll weight Up to 45Kg Up to 100lb
Widths Up to 4.06m (open) Up to 160in (open)
Formats available Lay-flat tube, sheet, V sheet
STORAGE
Stretch-Vac 2000 is hydrophilic material. Moisture and water act as plasticizers. The level of moisture content at time of use
is therefore an important factor for successful performance. The higher the moisture content the more flexible they become.
Conversely at lower moisture levels flexibility is limited.
Do not store rolls vertically on their ends
TECHNICAL DATA SHEE T
STRETCH- VAC
2000
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS SV2000_0 2.21_Issue1
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
TECHNICAL DATA SHEE T
STRETCH- VAC
2000
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS SV2000_0 2.21_Issue1
STRETCH- VAC 2000
Vacuum bagging film
Ideally suited to aerospace applications
Features and Benefits
Soft, co-extruded, ultra high elongation, multi layered
film, produced from a modified polyamide resin.
Easily conformable for complex contoured parts,
formulated to be less affected by environmental
changes and remains flexible in low humidity
conditions.
Recommended as a bagging film for advanced
composite fabrication, when a dependable,
conformable, soft, stretchable bag is required.
Fewer pleats are needed when vacuum bagging
either complex or simple contoured parts, due to its
unique characteristics.
Manufactured using advanced state-of-the-art
blown film technology.
Can be heat seamed to meet any custom shape
requirements.
PROPERTIES
Maximum use temperature 204 C 400 F
Color Red and transparent
Tensile strength at break (ASTM D882) 103.42 MPa 15000 PSI
Elongation at break (ASTM D882) 400%
Yield
50 m: 17.30m /kg
75 m: 11.60m /kg
9.39yd /lb
6.3yd /lb
AVAILABILITY
Thickness 50 and 75 m 0.002 and 0.003in
Roll weight Up to 45Kg Up to 100lb
Widths Up to 4.06m (open) Up to 160in (open)
Formats available Lay-flat tube, sheet, V sheet
STORAGE
Stretch-Vac 2000 is hydrophilic material. Moisture and water act as plasticizers. The level of moisture content at time of use
is therefore an important factor for successful performance. The higher the moisture content the more flexible they become.
Conversely at lower moisture levels flexibility is limited.
Do not store rolls vertically on their ends
TECHNICAL DATA SHEE T
STRETCH- VAC
2000
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS SV2000_0 2.21_Issue1
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
by | Sep 27, 2025
Material Safety Guidance Sheet
Lantor Coremat
XM
Nonwoven Core Material Rev. Apr-20
The information contained in this document has been compiled in good faith by Lantor BV, but nevertheless no representation or
warranty is given as to the accuracy or completeness of the (technical) information provided herein. Lantor BV cannot be held liable of any
damages arising from any (printing) errors or omissions in this information. Lantor BV reserves the right to make changes with respect to
the information provided at any time without further notice Page 1 of 5
Lantor Lantor Coremat
XM is classified as non-hazardous according to
EC and OHSA regulations.
A safety datasheet is not required for non-hazardous articles.
The following document provides a Material Safety Guidance Sheet (MSGS) for nonwovens on a voluntary basis
according to EDANA recommendations (Guidelines/instructions relating to MSGS for nonwovens 10/GV8/422).
The MSGS is a means of transferring essential hazard information (including information on transport, handling,
storage and emergency actions) from the supplier of a nonwoven product to the recipient of the product.
As nonwovens are generally not hazardous, MSGS for nonwovens is not legally requested but must be
considered as information. It is inspired from the ECHA_2011_G_08-EN as recommendation for MSGS,
EC1907/2006.
Material Safety Guidance Sheet
Lantor Coremat
XM
Nonwoven Core Material Rev. Apr-20
The information contained in this document has been compiled in good faith by Lantor BV, but nevertheless no representation or
warranty is given as to the accuracy or completeness of the (technical) information provided herein. Lantor BV cannot be held liable of any
damages arising from any (printing) errors or omissions in this information. Lantor BV reserves the right to make changes with respect to
the information provided at any time without further notice Page 2 of 5
1. Identification of the product and the company
Identification of the product(s) Product Name: Coremat XM
Product Code: M55002; M55003; M55004; M55010
Intended use Liner and core material in FRP application
Company identification
Company name Lantor BV
Address P.O. Box 45, 3900 AA Veenendaal, The Netherlands
Contact +31 (0)318 537111; info@lantor.com
2. Hazards identification
Not hazardous under normal conditions according to EC and OHSA regulations.
Keep away from fire.
Accidental thermal decomposition or melting state can present hazards, see section 10
3. Composition / Information on ingredients
Identification of the type of nonwoven product.
Nonwoven Carded web, chemically bonded
Nature of the fibre(s) Polyester (PES)
Web surface treatment Cured acrylic binder
Binder Acrylic
Additives Acrylic copolymer encapsulating a blowing agent
Other major components None
Chemicals listed as dangerous
substances. None
The product does not contain any other chemicals (in relevant concentration) that are in the list of
dangerous substances.
Material Safety Guidance Sheet
Lantor Coremat
XM
Nonwoven Core Material Rev. Apr-20
The information contained in this document has been compiled in good faith by Lantor BV, but nevertheless no representation or
warranty is given as to the accuracy or completeness of the (technical) information provided herein. Lantor BV cannot be held liable of any
damages arising from any (printing) errors or omissions in this information. Lantor BV reserves the right to make changes with respect to
the information provided at any time without further notice Page 3 of 5
4. First aid measures
Under normal condition.
Inhalation No specific measure to be taken.
Skin contact No specific measure to be taken.
Eyes contact Flush with sufficient amount of water for at least 15
minutes. If irritation or other ill effects persist, get
medical help
Ingestion Unlikely. In case of ingestion, get medical help
5. Firefighting measures
Suitable extinguishing media Water(spray), water/foam, carbon dioxide or dry powder.
Extinguishing-media not to be used Water in case short-circuiting is the cause of the fire.
Special exposure hazard For flammable and toxic fumes as well as skin contact
with molten materials see section 10.
Special protective clothing for fire-fighter No special requirements.
6. Accidental release measures
Not Applicable
7. Handling and storage
Handling No Special requirements.
Protection against fire and explosion No special requirements.
Storage Keep Lantor Lantor Coremat
XM in the original
package. Store in a dry, cool and well ventilated area.
The temperature should be above 0 C but must not
exceed 30 C.
Recommended maximum storage duration is 2 years.
8. Exposure controls and personal protection
General measure of protection General room ventilation is recommended.
General protection No special requirements.
Material Safety Guidance Sheet
Lantor Coremat
XM
Nonwoven Core Material Rev. Apr-20
The information contained in this document has been compiled in good faith by Lantor BV, but nevertheless no representation or
warranty is given as to the accuracy or completeness of the (technical) information provided herein. Lantor BV cannot be held liable of any
damages arising from any (printing) errors or omissions in this information. Lantor BV reserves the right to make changes with respect to
the information provided at any time without further notice Page 4 of 5
9. Physical and chemical properties
Appearance Off-White with hexagonal pattern
Odour Neutral
pH Not Applicable
Boiling point/boiling range Not Applicable
Melting point/melting range 250 265 C (PES fibres)
Decomposition temperature 450 C
Flash point Not Applicable
Flammability Not easily flammable (see section 10)
Auto flammability (temperature) > 450 C
Explosive properties Not Applicable
Oxidizing properties Not Applicable
Vapor pressure Not Applicable
Relative density 0,050 – 0,080 (water, room temperature)
Water solubility Insoluble
Fat solubility Insoluble
Styrene solubility Fibre binder will dissolve in styrene
Partition coefficient octanol/water Not Applicable
Material Safety Guidance Sheet
Lantor Coremat
XM
Nonwoven Core Material Rev. Apr-20
The information contained in this document has been compiled in good faith by Lantor BV, but nevertheless no representation or
warranty is given as to the accuracy or completeness of the (technical) information provided herein. Lantor BV cannot be held liable of any
damages arising from any (printing) errors or omissions in this information. Lantor BV reserves the right to make changes with respect to
the information provided at any time without further notice Page 5 of 5
10. Stability and reactivity
The materials are chemically stable.
Under thermal decomposition flammable and toxic fumes can be generated. The generation of cleavage
and oxidation products is subject to fire conditions. Non burned residues and contaminated water after
firefighting should be disposed of in compliance with official regulations. Molten material should not be
allowed to be in contact with the skin to which it can cause burns.
11. Toxicological information
No toxic reaction known under normal conditions.
Note: Under decomposition conditions; toxic fumes and contaminated water, see section 10.
12. Ecological information
For transportation, storage, normal use, no toxicological effect known.
13. Disposal considerations
As non-hazardous solid waste, nonwovens can be disposed of, depending on local legislation, through
recycling, incineration or landfill.
14. Transport information
Not classified as hazardous for transport.
Keep the product dry during transportation.
In case of fire see sections 5 and 10
No further specific requirements.
15. Regulatory information
None.
16. Other information
None
by | Sep 27, 2025
Page 1 of 3
MATERIAL SAFETY DATA SHEET Prepared: 29 January 2013
Section 1 Product and Company Identification
Product(s): SCRUBS Hand Cleaner Towels
Formula: B422
Part Number(s): 42201, 42210, 42225, 42230, 42256, 42260, 42272, 42280
Company Name & Address:
805 E. Old 56 Hwy.
Olathe, KS 66061
800-443-9536 (8 a.m. 5 p.m. Weekdays, CDT)
Emergency Numbers: IN CASE OF EMERGENCY, CALL Infotrac @ 1-800-535-5053, 24 hrs.
INTERNATIONAL EMERGENCY NUMBER 352-323-3500
Poison Control Center: 1-800-222-1222
Material Safety Data Sheets: www.itwprofessionalbrands.com
Section 2 Hazards Identification
CAUTION. May cause mild eye or skin irritation.
Potential Health Effects:
EYES: May cause mild eye irritation.
SKIN: May cause mild skin irritation.
INHALATION: Not a likely exposure route.
INGESTION: Not a likely exposure route.
Signs/symptoms of exposure: redness, tearing or burning in eyes. Redness, burning, drying or cracking of skin. Irritation of the
throat or stomach, nausea, vomiting, diarrhea if swallowed. Medical conditions generally aggravated by exposure: pre-existing
skin conditions such as dermatitis may be adversely affected by this and other oil and grease effective cleaners.
HMIS Rating Health 1 Flammability 0 Reactivity 0 Personal Protection None
Section 3 Composition/Information on Ingredients
Ingredient CAS Number Percent Range
Water 7732-18-5 60 100
Ethoxylated Alcohols (C12-15 pareth-7) 68131-39-5 1 5
Isoparaffin 64742-47-8 0.5 1.5
Dimethyl Glutarate 1119-40-0 0.5 1.5
Fragrance Mixture 0.5 2
Any substance listed as hazardous by the states of California, Florida, Illinois, Michigan, New Jersey, Ohio, Pennsylvania or
Texas is described above if known present in regulated concentrations.
Section 4 First Aid Measures
EYES: Immediately flush eyes with large amounts of water for at least 15 minutes while holding eyelids open. If
irritation persists seek medical attention.
SKIN: None usually required. Material is designed for skin cleansing. If symptoms develop seek medical attention.
INHALATION: Unlikely route as liquid is impregnated on a towel, minimizing exposure via this route. If overexposed move
to fresh air. If symptoms develop seek medical attention.
INGESTION: Not a likely exposure route. If a large quantity of liquid is swallowed, do not induce vomiting, call a physician
or poison control center immediately.
Formula: B422 Page 2 of 3
Section 5 Fire Fighting Measures
Flashpoint (PMCC): None to boiling, solution on towel.
Extinguishing Media: Dry chemical, carbon dioxide, foam, fog or water spray.
Special Fire Fighting Procedures: Keep containers cool and vapors down with water spray. Prevent runoff from
entering sewers and public waterways.
Hazardous Products of Combustion: Carbon monoxide, carbon dioxide, various hydrocarbons, hydrogen sulfide,
sulfur dioxide and soot.
Section 6 Accidental Release Measures
Small spill: Wipe up small releases with a dry absorbent cloth or other absorbent material.
Large spill: Absorb liquid with vermiculite, absorbent cloth, or other absorbent material. Prevent material from entering
sewers and drains. Ventilate area and block traffic. Transfer contaminated material into suitable container
for proper disposal.
Section 7 Handling and Storage
Handling: Do not allow towel contact with eyes. For external use only. Not for use around the mouth or eyes for an
extended period of time. Do not smoke while using. Use from original container only and follow label
directions carefully. Follow good chemical hygiene practices when handling this material.
Storage: Keep container closed when not in use. Keep away from heat sources. Store in a cool well-ventilated area.
Keep out of reach of children. Do not contaminate water, food or feed by use or storage. Keep from freezing.
Section 8 Exposure Controls/Personal Protection
Engineering controls: Ventilation not usually necessary but should be provided in the event of overexposure.
Exposure limits: Isoparaffin (CAS# 64742-47-8): 152 ppm, Manufacturer s recommendation
Eye protection: None necessary. Do not allow towel to directly contact eyes.
Skin protection: None necessary. Product is designed for direct skin use.
Respiratory protection: Not usually necessary. If vapors are present or irritation is experienced, use NIOSH/MSHA
approved respirator.
Section 9 Physical and Chemical Properties
Appearance and Odor: Colorless liquid with a orange scent saturated onto towels.
pH: 6.0 +/- 0.5 Boiling Point: 212 F Specific Gravity: 0.995
Vapor Density: >1 Vapor Pressure: No Data Solubility in Water: Miscible
Evaporation Rate: No Data Volatile Organic Compounds (VOCs): 0% by weight
Section 10 Stability and Reactivity
Hazardous Polymerization: This product will not undergo hazardous polymerization.
Hazardous Decomposition or Byproducts: Carbon monoxide, carbon dioxide, hydrogen sulfide, sulfur dioxide and soot.
Chemical Stability: Stable
Incompatible Materials: Strong oxidizers and strong acids.
Section 11 Toxicological Information
Ethoxylated Alcohols, CAS# 68131-39-5
Acute Dermal LD50 <5g/kg, rabbit; Acute Oral LD50 1.6-2.7g/kg, rat
Section 12 Ecological Information
Ethoxylated Alcohols, CAS# 68131-39-5
96 hr fathead minnow static acute LC50:2.7mg/L; 48 hr Daphnia acute EC50:0.4-0.75 mg/L
Section 13 Disposal Considerations
Dispose of in accordance with all applicable local, state, and federal regulations.
Waste information: If this product becomes a waste, it would not be hazardous as defined by RCRA (40CFR261). However
the waste should be properly evaluated in case of modification prior to disposal.
Formula: B422 Page 3 of 3
Section 14 Transport Information
The following transportation information is based on Department of Transportation Regulations found in 49 CFR. If shipping this
product by air please refer to International Air Transport Association (IATA) Dangerous Goods Regulations. If shipping this
product by ocean please refer to International Maritime Dangerous Goods Regulations (IMDG). To find how to ship this product
please refer to the UN# listed below.
UN # Proper Shipping Hazard Packing
Description Class Group
DOT Information None Not Regulated None None
Marine Pollutants: None
Section 15 Regulatory Information
US Federal Regulations
Toxic Substances Control Act (TSCA): All ingredients are on the TSCA inventory or exempt from listing.
CERCLA RQ
None
SARA 313 Components
None
State and Local Regulations
California Proposition 65
None
NSF Registration Category Code
E4, #138879
Section 16 Other Information
WARNING! The use of this product is beyond the control of the manufacturer; therefore, no guarantee, expressed or implied, is
made as to the effects of such or the results to be obtained if not used in accordance with directions or established safe practice.
The user must assume all responsibility, including injury or damage, resulting from its misuse as such, or in combination with
other materials. The manufacturer warrants only that this product meets the manufacturer's specifications for such product.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, AS TO DESCRIPTION, QUALITY,
AND MERCHANTABILITY. FITNESS FOR ANY PARTICULAR PURPOSE, PRODUCTIVENESS OR ANY OTHER MATTER,
OF THIS PRODUCT. THE MANUFACTURER SHALL BE IN NO WAY RESPONSIBLE FOR THE IMPROPER USE OF THIS
PRODUCT. The sole and exclusive remedy against the manufacturer for breach of warranty shall be reimbursement of the
purchase price of the product in the event that a defective condition of the product shall be found to exist. NO OTHER REMEDY
(INCLUDING BUT NOT LIMITED TO INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR INJURY TO PERSON OR
PROPERTY OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL LOSS) SHALL BE AVAILABLE.
by | Sep 27, 2025
by | Sep 27, 2025
by | Sep 27, 2025
by | Sep 27, 2025
SE 84LV Glass 30-56% Resin Content
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
Date of issue: 05/13/2015 Revision date: 08/29/2018 Supersedes: 07/08/2016 Version: 2.3
08/29/2018 USA ()Page 1
SECTION 1: Identification
1.1. Identification
Product form :ArticleName :SE 84LV Glass 30-56% Resin Content
1.2. Recommended use and restrictions on use
Recommended use :The product is intended for professional use
1.3. Supplier
Gurit (USA) Inc
115 Broadcommon Road
Rhode Island, 2809 – USA
T 18198689182 – F 001 819 847 2572
marine-na@gurit.com – www.Gurit.com
1.4. Emergency telephone number
Emergency number :Carechem 24: +1 646 844 7309
Carechem 24 (Toll Free): +1 866 928 0789
SECTION 2: Hazard(s) identification
2.1. Classification of the substance or mixture
GHS-US classification
Skin corrosion/irritation,
Category 2
H315 Causes skin irritation.Skin sensitisation, Category
1
H317 May cause an allergic skin reaction.Hazardous to the aquatic
environment Chronic
Hazard, Category 3
H412 Harmful to aquatic life with long lasting effects.
Full text of H statements : see section 16
2.2. GHS Label elements, including precautionary statements
GHS-US labelling
Hazard pictograms (GHS-US) :Signal word (GHS-US) :WarningHazard statements (GHS-US) :H315 – Causes skin irritation.
H317 – May cause an allergic skin reaction.
H412 – Harmful to aquatic life with long lasting effects.
Precautionary statements (GHS-US) :P261 – Avoid breathing vapours.
P264 – Wash hands thoroughly after handling.
P272 – Contaminated work clothing must not be allowed out of the workplace
P273 – Avoid release to the environment.
P280 – Wear eye protection, protective clothing, protective gloves.
P302+P352 – If on skin: Wash with plenty of water
2.3. Other hazards which do not result in classification
No additional information available
2.4. Unknown acute toxicity (GHS US)
Not applicable
SECTION 3: Composition/information on ingredients
3.1. Substances
Not applicable
3.2. Mixtures
SE 84LV Glass 30-56% Resin Content
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
08/29/2018 USA ()2/7NameProduct identifierGHS-US classificationFormaldehyde, polymer with (chloromethyl)oxirane and
phenol
(CAS-No.) 9003-36-525 – 50Skin Irrit. 2, H315
Skin Sens. 1, H317
Aquatic Acute 1, H400
Aquatic Chronic 2, H411
Phenol, polymer with formaldehyde, glycidyl ether(CAS-No.) 28064-14-410 – 25Skin Irrit. 2, H315
Skin Sens. 1, H317
Aquatic Chronic 2, H411
reaction product: bisphenol-A-(epichlorhydrin); epoxy resin
(number average molecular weight 700)
(CAS-No.) 25068-38-65 – 10Skin Irrit. 2, H315
Eye Irrit. 2A, H319
Skin Sens. 1, H317
Aquatic Chronic 2, H411
Full text of hazard classes and H-statements : see section 16
SECTION 4: First-aid measures
4.1. Description of first aid measures
First-aid measures after inhalation :Remove person to fresh air and keep comfortable for breathing.First-aid measures after skin contact :Wash skin with plenty of water. Take off contaminated clothing. If skin irritation or rash occurs:
Get medical advice/attention.
First-aid measures after eye contact :Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing. If eye irritation persists: Get medical advice/attention.
First-aid measures after ingestion :Call a poison center or a doctor if you feel unwell.
4.2. Most important symptoms and effects (acute and delayed)
Symptoms/effects after skin contact :Irritation. May cause an allergic skin reaction.Symptoms/effects after eye contact :Eye irritation.
4.3. Immediate medical attention and special treatment, if necessary
Treat symptomatically.
SECTION 5: Fire-fighting measures
5.1. Suitable (and unsuitable) extinguishing media
Suitable extinguishing media :Water spray. Dry powder. Foam. Carbon dioxide.Unsuitable extinguishing media :Do not use a heavy water stream.
5.2. Specific hazards arising from the chemical
Reactivity :The product is non-reactive under normal conditions of use, storage and transport. Product is
not explosive.
5.3. Special protective equipment and precautions for fire-fighters
Protection during firefighting :Do not attempt to take action without suitable protective equipment. Self-contained breathing
apparatus. Complete protective clothing.
Other information :Collect contaminated fire fighting water seperately. It must not enter drains.
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
6.1.1.For non-emergency personnel
Emergency procedures :Ventilate spillage area. Avoid contact with skin and eyes. Avoid breathing vapours.
6.1.2.For emergency responders
Protective equipment :Do not attempt to take action without suitable protective equipment. For further information
refer to section 8: “Exposure controls/personal protection”.
Emergency procedures :Ventilate area.
6.2. Environmental precautions
Avoid release to the environment. Notify authorities if liquid enters sewers or public waters.
6.3. Methods and material for containment and cleaning up
For containment :Collect spillage.Other information :Dispose of materials or solid residues at an authorized site.
6.4. Reference to other sections
For further information refer to section 13. For further information refer to section 8: “Exposure controls/personal protection”.
SE 84LV Glass 30-56% Resin Content
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
08/29/2018 USA ()3/7
SECTION 7: Handling and storage
7.1. Precautions for safe handling
Precautions for safe handling :Ensure good ventilation of the work station. Avoid contact with skin and eyes. Wear personal
protective equipment. Avoid breathing vapours. Handle in accordance with good industrial
hygiene and safety procedures.
Handling temperature :<= 35 CHygiene measures :Wash contaminated clothing before reuse. Contaminated work clothing should not be allowed
out of the workplace. Do not eat, drink or smoke when using this product. Always wash hands
after handling the product. Separate working clothes from town clothes. Launder separately.
Wash hands and other exposed areas with mild soap and water before eating, drinking or
smoking and when leaving work.
7.2. Conditions for safe storage, including any incompatibilities
Storage conditions :Store in a well-ventilated place. Keep cool.Maximum storage period :2 yearStorage temperature :-23 - 13 CStorage area :Store away from heat. Store in a well-ventilated place.Special rules on packaging :Keep only in original container.
SECTION 8: Exposure controls/personal protection
8.1. Control parameters
Formaldehyde, polymer with (chloromethyl)oxirane and phenol (9003-36-5)Not applicable reaction product: bisphenol-A-(epichlorhydrin); epoxy resin (number average molecular weight 700) (25068-38-6)Not applicable Phenol, polymer with formaldehyde, glycidyl ether (28064-14-4)Not applicable
8.2. Appropriate engineering controls
Appropriate engineering controls :Ensure good ventilation of the work station.Environmental exposure controls :Avoid release to the environment.
8.3. Individual protection measures/Personal protective equipment
Personal protective equipment:Safety glasses.
Hand protection:Protective glovesTypeMaterialPermeationThickness (mm)PenetrationDisposable glovesNitrile rubber (NBR)Eye protection:Safety glassesSkin and body protection:Wear suitable protective clothing. Long sleeved protective clothingTypeTyvek Gown/Coveralls
Respiratory protection:In case of insufficient ventilation, wear suitable respiratory equipment. Where exposure through inhalation may occur from use, respiratory
protection equipment is recommended
Device Filter typeConditionDisposable half maskGas/vapour filterVapour protection
SE 84LV Glass 30-56% Resin Content
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
08/29/2018 USA ()4/7
Personal protective equipment symbol(s):
Other information:Industrial and professional. Perform risk assessment prior to use. Do not eat, drink or smoke during use.
SECTION 9: Physical and chemical properties
9.1. Information on basic physical and chemical properties
Physical state :Solid
Appearance :Flexible Sheet.Colour :white
Odour :odourless
Odour threshold :No data available
pH :Not applicable
Melting point :Not applicable.
Freezing point :Not applicable.
Boiling point :Not applicable.
Flash point :Not applicable.
Relative evaporation rate (butylacetate=1) :No data available
Flammability (solid, gas) :> 100 C estimated
Not flammable.
Vapour pressure :No data available
Relative vapour density at 20 C :No data available
Relative density :No data available
Solubility :insoluble in water.
Log Pow :No data available
Auto-ignition temperature :No data available
Decomposition temperature :No data available
Viscosity, kinematic :No data availableViscosity, dynamic :Not applicable.
Explosive limits :No data available
Explosive properties :No data available
Oxidising properties :No data available
9.2. Other information
No additional information available
SECTION 10: Stability and reactivity
10.1.Reactivity
The product is non-reactive under normal conditions of use, storage and transport. Product is not explosive.
10.2.Chemical stability
Stable under normal conditions.
10.3.Possibility of hazardous reactions
No dangerous reactions known under normal conditions of use.
10.4.Conditions to avoid
None under recommended storage and handling conditions (see section 7).
10.5.Incompatible materials
No additional information available
SE 84LV Glass 30-56% Resin Content
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
08/29/2018 USA ()5/7
10.6.Hazardous decomposition products
Under normal conditions of storage and use, hazardous decomposition products should not be produced.
SECTION 11: Toxicological information
11.1.Information on toxicological effects
Acute toxicity (oral) :Not classifiedAcute toxicity (dermal) :Not classifiedAcute toxicity (inhalation) :Not classifiedFormaldehyde, polymer with (chloromethyl)oxirane and phenol (9003-36-5)LD50 oral rat> 2 g/kgreaction product: bisphenol-A-(epichlorhydrin); epoxy resin (number average molecular weight 700) (25068-38-6)LD50 oral rat11400 mg/kgATE US (oral)11400 mg/kg bodyweightSkin corrosion/irritation :Causes skin irritation.
pH: Not applicable
Serious eye damage/irritation :Not classified
pH: Not applicable
Respiratory or skin sensitisation :May cause an allergic skin reaction.Germ cell mutagenicity :Not classifiedCarcinogenicity :Not classifiedReproductive toxicity :Not classifiedSTOT-single exposure :Not classifiedSTOT-repeated exposure :Not classifiedAspiration hazard :Not classifiedViscosity, kinematic :No data availableSymptoms/effects after skin contact :Irritation. May cause an allergic skin reaction.Symptoms/effects after eye contact :Eye irritation.
SECTION 12: Ecological information
12.1.Toxicity
Ecology – general :Harmful to aquatic life with long lasting effects.Formaldehyde, polymer with (chloromethyl)oxirane and phenol (9003-36-5)LC50 fish 1< 1 mg/lreaction product: bisphenol-A-(epichlorhydrin); epoxy resin (number average molecular weight 700) (25068-38-6)LC50 fish 11.5 mg/lLC50 fish 22 mg/l
12.2.Persistence and degradability
reaction product: bisphenol-A-(epichlorhydrin); epoxy resin (number average molecular weight 700) (25068-38-6)Persistence and degradabilityMay cause long-term adverse effects in the environment.
12.3.Bioaccumulative potential
reaction product: bisphenol-A-(epichlorhydrin); epoxy resin (number average molecular weight 700) (25068-38-6)Bioaccumulative potentialNot established.
12.4.Mobility in soil
No additional information available
12.5.Other adverse effects
No additional information available
SE 84LV Glass 30-56% Resin Content
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
08/29/2018 USA ()6/7
SECTION 13: Disposal considerations
13.1.Disposal methods
Regional legislation (waste) :Disposal must be done according to official regulations.Waste treatment methods :Dispose of contents/container in accordance with licensed collector s sorting instructions.Product/Packaging disposal recommendations :Avoid release to the environment. Dispose in a safe manner in accordance with local/national
regulations.
Ecology - waste materials :Avoid release to the environment.
SECTION 14: Transport information
Department of Transportation (DOT)
In accordance with DOT
Transportation of Dangerous GoodsTransport by sea
Proper Shipping Name (IMDG) :Not classified for transport
Air transport
Proper Shipping Name (IATA) :Not classified for transport
SECTION 15: Regulatory information
15.1. US Federal regulations
All components of this product are listed, or excluded from listing, on the United States Environmental Protection Agency Toxic
Substances Control Act (TSCA) inventory
This product or mixture is not known to contain a toxic chemical or chemicals in excess of the applicable de minimis concentration as specified
in 40 CFR 372.38(a) subject to the reporting requirements of section 313 of Title III of the Superfund Amendments and Reauthorization Act of
1986 and 40 CFR Part 372.
15.2. International regulations
CANADA
Formaldehyde, polymer with (chloromethyl)oxirane and phenol (9003-36-5)Listed on the Canadian DSL (Domestic Substances List)reaction product: bisphenol-A-(epichlorhydrin); epoxy resin (number average molecular weight 700) (25068-38-6)Listed on the Canadian DSL (Domestic Substances List)Phenol, polymer with formaldehyde, glycidyl ether (28064-14-4)Listed on the Canadian DSL (Domestic Substances List)
EU-Regulations
Formaldehyde, polymer with (chloromethyl)oxirane and phenol (9003-36-5)Listed on the EU NLP (No Longer Polymers) inventoryreaction product: bisphenol-A-(epichlorhydrin); epoxy resin (number average molecular weight 700) (25068-38-6)Listed on the EU NLP (No Longer Polymers) inventory
National regulations
SE 84LV Glass 30-56% Resin Content
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
08/29/2018 USA ()7/7Formaldehyde, polymer with (chloromethyl)oxirane and phenol (9003-36-5)Listed on the AICS (Australian Inventory of Chemical Substances)
Listed on IECSC (Inventory of Existing Chemical Substances Produced or Imported in China)
Listed on the Japanese ENCS (Existing & New Chemical Substances) inventory
Listed on the Korean ECL (Existing Chemicals List)
Listed on NZIoC (New Zealand Inventory of Chemicals)
Listed on PICCS (Philippines Inventory of Chemicals and Chemical Substances)
Listed on INSQ (Mexican National Inventory of Chemical Substances)
Listed on Turkish inventory of chemical
reaction product: bisphenol-A-(epichlorhydrin); epoxy resin (number average molecular weight 700) (25068-38-6)Listed on the AICS (Australian Inventory of Chemical Substances)
Listed on IECSC (Inventory of Existing Chemical Substances Produced or Imported in China)
Listed on the Japanese ENCS (Existing & New Chemical Substances) inventory
Listed on the Korean ECL (Existing Chemicals List)
Listed on NZIoC (New Zealand Inventory of Chemicals)
Listed on PICCS (Philippines Inventory of Chemicals and Chemical Substances)
Listed on Turkish inventory of chemical
Phenol, polymer with formaldehyde, glycidyl ether (28064-14-4)Listed on the AICS (Australian Inventory of Chemical Substances)
Listed on IECSC (Inventory of Existing Chemical Substances Produced or Imported in China)
Listed on the Japanese ENCS (Existing & New Chemical Substances) inventory
Listed on the Korean ECL (Existing Chemicals List)
Listed on NZIoC (New Zealand Inventory of Chemicals)
Listed on PICCS (Philippines Inventory of Chemicals and Chemical Substances)
15.3. US State regulations
California Proposition 65 - This product does not contain any substances known to the state of California to cause cancer, developmental and/or
reproductive harm
ComponentState or local regulationsFormaldehyde, polymer with (chloromethyl)oxirane and
phenol(9003-36-5)
reaction product: bisphenol-A-(epichlorhydrin); epoxy
resin (number average molecular weight 700)(25068-
38-6)
Phenol, polymer with formaldehyde, glycidyl
ether(28064-14-4)
SECTION 16: Other information
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
Revision date :08/29/2018
Full text of H-statements:H315Causes skin irritation.H317May cause an allergic skin reaction.H319Causes serious eye irritation.H400Very toxic to aquatic life.H411Toxic to aquatic life with long lasting effects.H412Harmful to aquatic life with long lasting effects.
SDS US (GHS HazCom 2012)
This information is based on our current knowledge and is intended to describe the product for the purposes of health, safety and environmental requirements only. It should not therefore be construed as
guaranteeing any specific property of the product The information contained within this document is Gurit copyright and any distribution or publication beyond the recipient's organisation is prohibited
without Gurit's prior written consent.
