MATERIAL SAFETY DATA SHEET 3M Abrasive Product, 214U White Gold Paper Stikit Discs, 232U Hookit Paper Discs and
Rolls, 316U Red Abrasive Stikit Discs, Sheets, Rolls, P60-P800 05/18/10
_________________________________________________________________________________________________
Page 1of 8
Material Safety Data Sheet
Copyright, 2010, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M Abrasive Product, 214U White Gold Paper Stikit Discs, 232U Hookit Paper
Discs and Rolls, 316U Red Abrasive Stikit Discs, Sheets, Rolls, P60-P800
MANUFACTURER: 3M
DIVISION: Abrasives Systems Division
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 05/18/10
Supercedes Date: 12/08/09
Document Group:19-0346-7
Product Use:
Intended Use: Abrasive Product
SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by Wt
Aluminum Oxide Mineral 1344-28-1 10 -55
Lubricant 68424-16-8 0 -5
Cured Resin Mixture 10 -45
Paper Backing Mixture 15 -65
Stikit Backing Mixture 0 -10
Hookit Backing Mixture 0 -10
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: Abrasive Product
General Physical Form: Solid
Immediate health, physical, and environmental hazards: T hisdocument covers only the 3M product. For
MATERIAL SAFETY DATA SHEET 3M Abrasive Product, 214U White Gold Paper Stikit Discs, 232U Hookit Paper Discs and
Rolls, 316U Red Abrasive Stikit Discs, Sheets, Rolls, P60-P800 05/18/10
_________________________________________________________________________________________________
Page 2of 8
complete assessment, when determining the degree of hazard, the material being abraded must also be considered.
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
Mechanical eye irritation: Signs/symptoms may include pain, redness, tearing and corneal abrasion.
Dust created by cutting, grinding, sanding, or machining may cause eye irritation. Signs/symptoms may include redness, swelling,
pain, tearing, and blurred or hazy vision.
Skin Contact:
Mechanical Skin irritation: Signs/symptoms may include abrasion, redness, pain, and itching.
Inhalation:
Dust from cutting, grinding, sanding or machining may cause irritation of the respiratory system. Signs/symptoms may include cough,
sneezing, nasal discharge, headache, hoarseness, and nose and throat pain.
Prolonged or repeated exposure may cause:
Pneumoconiosis: Sign/symptoms may include persistent cough, breathlessness, chest pain, increased amounts of sputum, and
changes in lung function tests.
Maybe absorbed following inhalation and cause target organ effects.
Ingestion:
No health effects are expected.
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention.
Skin Contact: Wash affected area with soap and water. If signs/symptoms develop, get medical attention.
Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention.
If Swallowed: No need for first aid is anticipated.
MATERIAL SAFETY DATA SHEET 3M Abrasive Product, 214U White Gold Paper Stikit Discs, 232U Hookit Paper Discs and
Rolls, 316U Red Abrasive Stikit Discs, Sheets, Rolls, P60-P800 05/18/10
_________________________________________________________________________________________________
Page 3of 8
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Autoignition temperature Not Applicable
Flash Point Not Applicable
Flammable Limits -LEL Not Applicable
Flammable Limits -UEL Not Applicable
5.2 EXTINGUISHING MEDIA
Ordinarycombustible material. Use fire extinguishers with class A extinguishing agents (e.g., water, foam).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus
(SCBA).
Unusual Fire and Explosion Hazards: Not applicable. None inherent in this product.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures:
Not applicable.
In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
Avoid breathing of dust created by sanding, grinding or machining. Avoid eye contact with dust or airborne particles. Damaged
product can break apart during use and cause serious injury to face or eyes. Check product for damage such as cracks or nicks prior to
use. Replace if damaged. Always wear eye and face protection when working at sanding or grinding operations or when near such
operations. Sparks and particles flying from the product during sanding or grinding can cause injury and fire.
7.2 STORAGE
Store in a cool, dry place.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
MATERIAL SAFETY DATA SHEET 3M Abrasive Product, 214U White Gold Paper Stikit Discs, 232U Hookit Paper Discs and
Rolls, 316U Red Abrasive Stikit Discs, Sheets, Rolls, P60-P800 05/18/10
_________________________________________________________________________________________________
Page 4of 8
Provide appropriate local exhaust ventilation for sanding, grinding or machining. Provide ventilation adequate to control dust
concentrations below recommended exposure limits and/or control dust. Use general dilution ventilation and/or local exhaust
ventilation to control airborne exposures to below Occupational Exposure Limits and/or control dust, fume, or airborneparticles. If
ventilation is not adequate, use respiratory protection equipment.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact. To minimize the risk of injury to face and eyes, always wear eye and face protection when working at sanding or
grinding operations or when near such operations.
The following eye protection(s) are recommended: Safety Glasses with side shields
.
8.2.2 Skin Protection
Avoid skin contact. Wear appropriate gloves to minimize risk of injury to skin from contact with dust or physical abrasion from
grinding or sanding.
8.2.3 Respiratory Protection
Avoid breathing of dust created by sanding, grinding or machining. Assess exposure concentrations of all materials involved in the
work process. Consider material being abraded when determining the appropriate resipratory protection. Select and use appropriate
respiratorsto prevent inhalation overexposure.
Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with
OSHA regulations: Half facepiece or fullface air-purifying respirator with N95 particulate filters
. Consult the current 3M Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of Swallowing
Not an expected route of exposure. Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap
and water.
8.3 EXPOSURE GUIDELINES
IngredientAuthorityType Limit Additional Information
Aluminum Oxide Mineral CMRG TWA 1 fiber/cc
Aluminum Oxide Mineral OSHA TWA, respirable
fraction
5 mg/m3
Aluminum Oxide Mineral OSHA TWA, as total dust15 mg/m3
PETROLEUM DISTILLATES OSHA TWA 2000 mg/m3
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Odor, Color, Grade: Abrasive Product
General Physical Form: Solid
MATERIAL SAFETY DATA SHEET 3M Abrasive Product, 214U White Gold Paper Stikit Discs, 232U Hookit Paper Discs and
Rolls, 316U Red Abrasive Stikit Discs, Sheets, Rolls, P60-P800 05/18/10
_________________________________________________________________________________________________
Page 5of 8
Autoignition temperature Not Applicable
Flash Point Not Applicable
Flammable Limits -LEL Not Applicable
Flammable Limits -UEL Not Applicable
Boiling point Not Applicable
Vapor Density Not Applicable
Vapor Pressure Not Applicable
Specific Gravity Not Applicable
pH Not Applicable
Melting point Not Applicable
Solubility In Water Not Applicable
SECTION 10: STABILITY AND REACTIVITY
Stability:Stable.
Materials and Conditions to Avoid:
10.1 Conditions to avoid
None known
10.2 Materials to avoid
None known
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products
Substance Condition
Carbon monoxide During Combustion
Carbon dioxide During Combustion
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
MATERIAL SAFETY DATA SHEET 3M Abrasive Product, 214U White Gold Paper Stikit Discs, 232U Hookit Paper Discs and
Rolls, 316U Red Abrasive Stikit Discs, Sheets, Rolls, P60-P800 05/18/10
_________________________________________________________________________________________________
Page 6of 8
Not determined.
CHEMICAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: The substrate that was abraded must be considered as a factor in the disposal method for this product.
Dispose of waste product in a sanitary landfill. As a disposal alternative, incinerate in an industrial or commercial facility in the
presence of a combustible material. Combustion products will include HCl. Facility must be capable of handling halogenated
materials.
EPA Hazardous Waste Number (RCRA):Not regulated
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
Not regulated per U.S. DOT, IATA or IMO.
These transportation classifications are provided as a customer service. As the shipper YOU remain responsible for
complying with all applicable laws and regulations, including proper transportation classification and packaging.3M s
transportation classifications are based on product formulation, packaging, 3M policies and 3M s understanding of applicable
current regulations. 3M does not guarantee the accuracy of this classification information. This information applies only to
transportation classification and notthe packaging, labeling, or marking requirements.The original 3M package is certified
for U.S. ground shipment only. If you are shipping by air or ocean, the package may not meet applicable regulatory
requirements.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard -No Pressure Hazard -No Reactivity Hazard -No Immediate Hazard -Yes Delayed Hazard -Yes
STATE REGULATIONS
Contact 3M for more information.
MATERIAL SAFETY DATA SHEET 3M Abrasive Product, 214U White Gold Paper Stikit Discs, 232U Hookit Paper Discs and
Rolls, 316U Red Abrasive Stikit Discs, Sheets, Rolls, P60-P800 05/18/10
_________________________________________________________________________________________________
Page 7of 8
CHEMICAL INVENTORIES
This product is an article as defined by TSCA regulations, and is exempt from TSCA Inventory listing requirements.
Contact 3M for more information.
INTERNATIONAL REGULATIONS
Contact 3M for more information.
WHMIS: Hazardous
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health: 1 Flammability: 1 Reactivity: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.
Revision Changes:
Section 1: Product name was modified.
Copyright was modified.
Section 8: Eye/face protection information was modified.
Section 8: Respiratory protection -recommended respirators information was modified.
Page Heading: Product name was modified.
Section 8: Exposure guidelines ingredient information was modified.
Section 10: Materials to avoid physical property was modified.
Section 10: Conditions to avoid physical property was modified.
Section 8: Exposure guidelines legend was deleted.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user’s method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user’s knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
MATERIAL SAFETY DATA SHEET 3M Abrasive Product, 214U White Gold Paper Stikit Discs, 232U Hookit Paper Discs and
Rolls, 316U Red Abrasive Stikit Discs, Sheets, Rolls, P60-P800 05/18/10
_________________________________________________________________________________________________
Page 8of 8
particular purpose and suitable for user’s method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
3M MSDSs are available at www.3M.com