23M5405-9_SDS.pdf

REVISED
NOV. /2014

MATERIAL SAFETY DATA SHEETS

1. CHEMICAL PRODUCT
Adhesive Systems, Inc.
9411 Corsair Road
Frankfort, IL 60423
1-800-552-0299 Phone
1-815-464-5650 Fax
EMERGENCY PHONE 1-800-255-3924 International +01+813-248-0585
Product Name: MP 5405 Part A (Resin)
Technical Name: Epoxy Resin

2. HAZARDS IDENTIFICATION

Inhalation effects: Not expected to be relevant, however, when exposure to vapors or mists is
possible, it could cause respiratory tract irritation.
Skin effects: May be mildly irritating. May cause skin sensitization.
Eye effects: May be mildly irritating.
Ingestion effects: Not likely to be a relevant route of exposure.
Human health hazards: May be irritating to the eyes and skin. Contact with hot material can cause
thermal burns. May cause skin sensitization.
Safety hazards: Material will not burn unless preheated.

Hazard Classification: N/A
Physical Classification:
Symbol: None
Signal Word: None

Health Classification:
Irritant: Causes mild skin or eye irritation Category 3
Symbol:

Signal Word: Warning

3. COMPOSITION AND INFORMATION ON HARMFUL INGREDIENTS

Ingredients Cas No. OSHA PEL ACGIH TLV Other Limits %Composition

Bisphenol-A-
(epichlorohydrin); epoxy
resin( number average
molecular weight<=700). 25068-38-6 N/A N/A N/A 100 *Proprietary means the specific chemical identity and/or weight percent is being withheld as a trade secret. Page 1 of 4 MATERIAL SAFETY DATA SHEETS MP 5405 Part A (Resin) Epoxy Resin 4. FIRST AID MEASURES Inhalation: Remove victim to fresh air and provide oxygen if breathing is difficult. Give artificial respiration if not breathing. Get medical attention. Skin contact: In case of contact with hot product, immediately flood the affected area with cold water. Wipe excess material from exposed area. Flush exposed skin with water and follow by washing with soap if available. Carefully remove clothing; if clothing is stuck to a burn area do not pull it off, but cut around it. Cover burn area do not pull it off, but cut around it. Transport to nearest medical facility for additional treatment. Eye contact: Flush eye with water. Rest eyes for 30 minutes. If symptoms persist, consult a physician. Ingestion: Do not induce vomiting. Have victim rinse out mouth with water, then drink sips of water to remove taste from mouth. In general, no treatment is necessary unless large quantities are ingested. However, get medical advice. If vomiting occurs spontaneously, keep head below hips to prevent aspiration. 5. FIRE FIGHTING MEASURES Extinguishing media: Carbon dioxide, dry chemical, foam, or water fog. Specific hazards during fire fighting: Material will not burn unless preheated. Cool fire exposed containers with water. Special protective equipment for fire fighters: Do not enter confined fire space without full bunker gear, including a SCBA. 6. ACCIDENTAL RELEASE MEASURES Spill control: Avoid contact. Evacuate area. Eliminate ignition sources. Ventilate area. Containment: Dike, contain, and absorb with clay, sand, or other suitable material. Cleanup: For large spills, pump to storage/salvage vessels. Soak up residue with clay, sand, or other suitable material. Special procedures: Prevent spill from entering drainage/sewer systems, waterways, and surface waters 7. HANDLING AND STORAGE Do not get in eyes, on skin or clothing. Wash with soap and water after using. Particularly before eating, drinking, smoking, applying cosmetics, or using toilet facilities. Air dry and then launder contaminated clothing and protective gear before reuse. Storage: keep in a cool, dry place. Keep containers closed when not in use. Keep away from open flames and high temperatures. 8. EXPOSURE CONTROL AND PERSONAL PROTECTION OSHA PEL: N/A Engineering Controls: Use good general local ventilation when working with this material. Eye Protection: Safety goggles / glasses suitable for use with chemicals. Respiratory protection: None required under normal conditions of use. Skin Protection: Nitrile / polyethylene gloves, coveralls, avoid cotton products. 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance and Odor: Flashpoint: 249 C Solubility in Water: Slight Boiling Point:>260 C
Specific Gravity: 1.17
Evaporation rate: N/D
Melting Point: N/D
Vapor Pressure: 0.03mbar @171 F

Page 2 of 4

MATERIAL SAFETY DATA SHEETS

MP 5405 Part A (Resin)
Epoxy Resin

10. REACTIVITY AND STABILIITY

This material is chemically stable. Hazardous polymerization will not occur.
Conditions to avoid: Avoid high temperatures.
Incompatible materials: Oxidizers, acids, and bases.

11. TOXICOLOGICAL INFORMATION

None

12. ECOLOGICAL INFORMATION

Biodegradability: This section will be completed as ecological reviews are completed.
Toxicity to fish: This section will be completed as ecological reviews are completed.

13. DISPOSAL INFORMATION

This material must be disposed in compliance with local, state, and federal regulations. When in consumer
packaging this material must be disposed of as household waste. Check local and state regulations for disposal of
this product as a household waste in your state or municipality.

14. TRANSPORTATION INFORMATION

Not regulated for transport.

15. REGULATORY INFORMATION

TSCA: All components listed.
DSL: All components listed.
SARA Section 311/312 hazard classes: Chronic health hazard.
California Proposition 65: Contains Phenyl Glycidyl Ether (< 6 PPM), which was listed as carcinogenic on October 1st, 1990. Page 3 of 4 MATERIAL SAFETY DATA SHEETS MP5405 Part A (Resin) Methyl Methacryalte 16. OTHER INFORMATION Initial: 8/22/2007 Revised: Nov. 2014 HMIS HEALTH 2 FLAMMABILITY 1 REACTIVITY 0 NFPA HEALTH 2 FIRE HAZARD 1 REACTIVITY 0 NON-WARRANTY: Information contained herein is based on tests we believe to be reliable and accurate. It is offered in good faith for the benefit of the consumer. Adhesive Systems shall not be liable for any injury, loss, or damage in the use of it's chemical products since the conditions of use are beyond our control. In every case we urge and recommend the user conduct tests to determine to their own satisfaction that the product is of acceptable quality and is suitable for their particular purpose under their own operating conditions. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent. Because of changing reporting requirements and other variables it is impossible to guarantee the accuracy of the information contained in this document. It is the responsibility of the user to determine proper personal protection based on the actual condition of use and to comply with all Federal, State, and Local laws and regulations. Revised Nov. 2014 Page 4 of 4 Page 1 of 4 REVISED NOV./2014 MATERIAL SAFETY DATA SHEETS 1. CHEMICAL PRODUCT Adhesive Systems, Inc. 9411 Corsair Road Frankfort, IL 60423 1-800-552-0299 Phone 1-815-464-5650 Fax EMERGENCY PHONE 1-800-255-3924 International +01+813-248-0585 Product Name: MP 5405 Part B (Hardener) Technical Name: Curing Agent 2. HAZARDS IDENTIFICATION Routes of Entry: Skin, inhalation, and ingestion Health Hazards: (Inhalation) Considered slightly toxic by inhalation. Can cause irritation of respiratory tract and nausea. Overexposure may cause delayed lung injury and chemical pneumonia. (Skin) Causes skin irritation. (Eyes) Causes eye irritation. (Ingestion) Harmful if swallowed. Carcinogenicity: Not a known carcinogen. NTP: Not a known or anticipated carcinogen. IARC: This component has not been classified by the IARC. OSHA: Not an OSHA -Regulated Carcinogen. WHMIS: D2B Signs and Symptoms of Exposure: (Eyes) Redness, swelling, tearing, and hazy vision. (Skin) Redness, swelling, blistering, and itching. (Inhalation) Soreness of the nose and throat, coughing and sneezing. (Ingestion) Pain, vomiting, abdominal tenderness, nausea, blood in vomitus, and blood In feces. Medical Conditions Aggravated by Exposure: Preexisting eye, lung, and skin disorders may be aggravated by exposure. Emergency First Aid Procedures: (Inhalation) Remove victim to fresh air and provide oxygen if breathing is difficult. Give artificial respiration if not breathing. Get medical attention Hazard Classification: N/A Physical Classification: Hardener Symbol: none Signal Word: none Health Classification: Irritant: Causes mild skin or eye irritation Category 3 Symbol: Signal Word: Warning 3. COMPOSITION AND INFORMATION ON HARMFUL INGREDIENTS Ingredients Cas No. OSHA PEL ACGIH TLV Other Limits %Composition Mereaptan/Amine Blend Trade Secret N/A N/A N/A 90-100 Page 2 of 4 MATERIAL SAFETY DATA SHEETS MP 5405 Part B (Hardener) Curing Agent 4. FIRST AID MEASURES Inhalation: Remove victim to fresh air and provide oxygen if breathing is difficult. Give artificial respiration if not breathing. Get medical attention. Skin contact: In case of contact with hot product, immediately flood the affected area with cold water. Wipe excess material from exposed area. Flush exposed skin with water and follow by washing with soap if available. Carefully remove clothing; if clothing is stuck to a burn area do not pull it off, but cut around it. Cover burn area do not pull it off, but cut around it. Transport to nearest medical facility for additional treatment. Eye contact: Flush eye with water. Rest eyes for 30 minutes. If symptoms persist, consult a physician. Ingestion: Do not induce vomiting. Have victim rinse out mouth with water, then drink sips of water to remove taste from mouth. In general, no treatment is necessary unless large quantities are ingested. However, get medical advice. If vomiting occurs spontaneously, keep head below hips to prevent aspiration. 5. FIRE FIGHTING MEASURES Flash Point: 200 F (PMCC) Flammable Limits: LEL=N/D UEL=N/D Extinguishing Media: Water fog, foam, dry che mical or CO2. Special Fire Fighting Procedures: Wear self contained breathing apparatus. Cool fire -exposed containers with water. Unusual Fire and Explosion Hazards: None Known 6. ACCIDENTAL RELEASE MEASURES Ventilate area of spill. Flood area with water to polymerize. Absorb with sand / earth and dispose in accordance with local, state, and federal regulations. 7. HANDLING AND STORAGE When using large volumes ensure that operational area is well ventilated. Store between 5-25 C; avoid strong light and heat sources. These products should never be frozen. Avoid skin contact and inhalation of vapor. 8. EXPOSURE CONTROL AND PERSONAL PROTECTION Engineering Controls: Use good general local ventilation when working with this material. Eye Protection: Safety goggles / glasses suitable for use with chemicals. Respiratory Protection: Always use appropriate filter mask / respirator. Skin Protection: Nitrile / polyethylene gloves, coveralls, avoid cotton products. 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance and Odor: Clear to slig ht amber liquid with mercaptan-like odor. Flash Point: 200 F (PMC C) Boiling Point: Not Determined Specific Gravity @ 25 C:1.11-1.13 Vapor Pressure: Not Determined Melting Point: Not Determined Vapor Density: Not Determined Evaporation Rate: Not Determined Solubility in Water: Negligible (<0.1%) MATERIAL SAFETY DATA SHEETS MP 5405 Part B (Hardener) Curing Agent 10. REACTIVITY AND STABILITY Stability: Stable Incompatibility: Oxidizers Hazardous Polymerizat ion: Will not occur. Conditions to Avoid: No known conditions to avoid. Hazardous Decomposition: Oxides of ca rbon, nitrogen, and sulfur; hydrogen sulfide 11.TOXICOLOGICAL INFORMATION None 12. ECOLOGICAL INFORMATION None. 13. DISPOSAL INFORMATION This material must be disposed in compliance with local, state, and federal regulations. When in consumer packaging this material must be disposed of as household waste. Check local and state regulations for disposal of this product as a household waste in your state or municipality. 14. TRANSPORTATION INFORMATION U.S.DOT 15. REGULATORY INFORMATION TSCA All ingredients of this product are listed, or are exempt from listing, on the TSCA inventory. SARATitleIII,Section13 This product does contain the following chemical(s) which are defined as toxic chemicals under and subject to the reporting requirements of, Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and40CFRPart372. Methyl Methacrylate Page 3 of 4 MATERIAL SAFETY DATA SHEETS MP 5405 Part B (Hardener) Curing Agent 16. OTHER INFORMATION Initial: 8/22/2007 Revised: Nov. 2014 HMIS HEALTH 2 FLAMMABILITY 1 REACTIVITY 0 NFPA HEALTH 2 FIRE HAZARD 1 REACTIVITY 0 NON-WARRANTY: Information contained herein is based on tests we believe to be reliable and accurate. It is offered in good faith for the benefit of the consumer. Adhesive Systems shall not be liable for any injury, loss, or damage in the use of it's chemical products since the conditions of use are beyond our control. In every case we urge and recommend the user conduct tests to determine to their own satisfaction that the product is of acceptable quality and is suitable for their particular purpose under their own operating conditions. Statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent. Because of changing reporting requirements and other variables it is impossible to guarantee the accuracy of the information contained in this document. It is the responsibility of the user to determine proper personal protection based on the actual condition of use and to comply with all Federal, State, and Local laws and regulations. Revised Nov. 2014 Page 4 of 4