CHEMLINE CA, INC
CHEMLINE RF02.5 S45 PT B NEUTRAL
SDS
1 PRODUCT AND COMPANY IDENTIFICATION
CHEMLINE CA, INC
19500 SOUTH ALAMEDA STREET
EAST RANCHO DOMINGUEZ, CA 90221
CHEMTREC 800.424.9300 (24 HOURS)
(310)764-0820
(310)764-0822
WWW.CHEMLINE.NET
Emergency:
Phone:
Fax:
Web:
Supplier Details:
HAZARDS IDENTIFICATION2
Eyes; Ingestion; Inhalation; Skin;Route of Entry:
Target Organs: Eyes; Skin; Respiratory system;
Inhalation: Heating, spraying, foaming or otherwise mechanically dispersing operations way generate vapor
or aerosol concentrations sufficient to cause irritation or other adverse effects. Minimal respiratory
tract irritation may occur with exposure to a large amount of material.
Skin Contact: Prolonged or repeated exposure can cause skin irritation or dermatitis in some individuals.
Eye Contact: May cause watering of the eye and irritation of the conjunctiva.
May cause nausea or vomiting.
Classification of the Substance or Mixture
GHS Label Elements, Including Precautionary Statements
Hazards not Otherwise Classified (HNOC) or not Covered by GHS
NONEGHS Signal Word:
No GHS Classifications Indicated
GHS Classification in Accordance with 29 CFR 1910 (OSHA HCS):
P261 – Avoid breathing dust/fume/gas/mist/vapors/spray.
P264 – Wash skin thoroughly after handling.
P270 – Do not eat, drink or smoke when using this product.
P271 – Use only outdoors or in a well-ventilated area.
P301+312 – IF SWALLOWED: Call a POISON CENTER or doctor/physician if you feel unwell.
P304+340 – IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P312 – Call a POISON CENTER or doctor/physician if you feel unwell.
P330 – Rinse mouth.
P403+233 – Store in a well ventilated place. Keep container tightly closed.
P405 – Store locked up.
P501 – Dispose of contents/container according to state, local and federal regulations.
No GHS hazards statements indicated
GHS Hazard Statements:
GHS Precautionary Statements:
Ingestion:
No GHS pictograms indicated for this product
COMPOSITION/INFORMATION OF INGREDIENTS3
Ingredients:
Cas# % Chemical Name
—————————————————-
0 95-100% Proprietary polyol blend
Revision Date: 3/22/2017SDS Number: RF02.5-B-30000-S45 CA Page 1 of 4
FIRST AID MEASURES4
Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, oxygen should be
administered by qualified personnel. Call a physician or transport to a medical facility immediately.
Remove all contaminated clothing and shoes. Wash skin with large quantities of water and soap. Wash
clothing before wearing again and clean shoes. If redness, itching or a burning sensation develops or
persists after the area is washed, consult a physician.
Flush with large amounts of water for 15 minutes. Use fingers to assure that the eyelids are separated and
that the eye is being irrigated. Get immediate medical attention.
If swallowed, do not induce vomiting unless directed to do so by medical personnel. This material is an
aspiration hazard. Never give anything by mouth to an unconscious person. Seek medical attention.
Inhalation:
Skin Contact:
Eye Contact:
Ingestion:
FIRE FIGHTING MEASURES5
Dry powder, foam, carbon dioxide. Use cold water spray to cool fire exposed containers to minimize risk of rupture. A solid
stream of water directed into hot burning liquid could cause frothing. If possible, contain fire run off.
Flash Point: >200 F
Flash Point Method: COC
ACCIDENTAL RELEASE MEASURES6
Spill: Remove all sources of flames, heating elements, gas engines, etc. Emergency clean-up personnel should wear
chemical goggles, rubber or plastic gloves and clothing as required to protect against contact. Prevent spreading and
contamination of surface waters and drinking supplies. Notify local health officials and other appropriate agencies if such
contamination should occur.
Clean up: With adequate ventilation and appropriate personal protective equipment, cover the area with an inert absorbent
material such as clay or vermiculite and transfer to steel waste containers. Ventilate area to remove the remaining vapors.
HANDLING AND STORAGE7
Do not smoke or use naked lights, open flames, space heaters or other ignition sources near
pouring, frothing or spraying operations. If contamination with isocyantes is suspected, do not
reseal containers. Special Emphasis for spray applications of mixed products containing
isocyanates: Inspect the application area for potential to expose other persons or for
overspray to drift onto buildings, vehicles or other property. When spraying building exteriors,
persons entering or exiting the building as well as those inside could be exposed to
polyisocyanates due to wind conditions, open windows or air intakes. Do not begin application
work until these potential problems have been corrected.
When stored between 60 -85 F in sealed containers, typical shelf life is 6 months or more
from the date of manufacture. Open containers must be handled properly to prevent moisture
pickup.
Handling Precautions:
Storage Requirements:
EXPOSURE CONTROLS/PERSONAL PROTECTION8
All ventilation should be designed in accordance with OSHA standard (29 CFR 1910.94).
Uses requiring heating and/or spraying may require more agressive engineering controls or
PPE.
HMIS PP, X | Consult your supervisor for special instructions
Personal protective equipment
Respiratory protection: Where risk assessment shows air-purifying respirators are appropriate
use a full-face respirator with multi-purpose combination (US) or type ABEK (EN 14387)
respirator cartridges as a backup to engineering controls. If the respirator is the sole means of
Engineering Controls:
Personal Protective
Equipment:
Revision Date: 3/22/2017SDS Number: RF02.5-B-30000-S45 CA Page 2 of 4
protection, use a full-face supplied air respirator. Use respirators and components tested and
approved under appropriate government standards such as NIOSH (US) or CEN (EU).
Hand protection: Handle with gloves. Gloves must be inspected prior to use. Use proper glove
removal technique (without touching gloves outer surface) to avoid skin contact with this
product. Dispose of contaminated gloves after use in accordance with applicable laws and
good laboratory practices. Wash and dry hands. Splash contact Material: butyl-rubber
Minimum layer thickness: 0.3 mm Break through time: 30 min Material tested:Butoject (KCL
897 / Aldrich Z677647, Size M) data source: KCL GmbH, D-36124 Eichenzell, phone +49
(0)6659 87300, e-mail sales@kcl.de, test method: EN374 If used in solution, or mixed with
other substances, and under conditions which differ from EN 374, contact the supplier of the
CE approved gloves. This recommendation is advisory only and must be evaluated by an
industrial hygienist and safety officer familiar with the specific situation of anticipated use by
our customers. It should not be construed as offering an approval for any specific use
scenario.
Eye protection: Face shield and safety glasses Use equipment for eye protection tested and
approved under appropriate government standards such as NIOSH (US) or EN 166(EU).
Skin and body protection: Complete suit protecting against chemicals, Flame retardant
antistatic protective clothing, The type of protective equipment must be selected according to
the concentration and amount of the dangerous substance at the specific workplace.
Hygiene measures: Handle in accordance with good industrial hygiene and safety practice.
Wash hands before breaks and at the end of workday.
None available
PHYSICAL AND CHEMICAL PROPERTIES9
Liquid
N/A
>500 F
None Flammable
<1
Physical State:
Spec Grav./Density:
Boiling Point:
Flammability:
Evap. Rate:
Odor:
Flash Point:
Vapor Density:
Mild
>200 F
>1
Appearance: Non-Pigmented liquid.
STABILITY AND REACTIVITY10
Product is stable under normal conditions.
No specific data
No specific data
Under normal storage conditions hazardous decomposition products should not be produced.
Will not occur.
Chemical Stability:
Conditions to Avoid:
Materials to Avoid:
Hazardous Decomposition:
Hazardous Polymerization:
No specific dataReactivity:
TOXICOLOGICAL INFORMATION11
None available
ECOLOGICAL INFORMATION12
None available
Revision Date: 3/22/2017SDS Number: RF02.5-B-30000-S45 CA Page 3 of 4
DISPOSAL CONSIDERATIONS13
Disposal: Any disposal practice must be in compliance with all federal, state and local laws and regulations. Chemical
additions, processing or otherwise altering this material may make the waste management information presented in this
MSDS incomplete, inaccurate or otherwise inappropriate. Waste characterization and disposal compliance are the
responsibility solely of the party generating the waste or deciding to discard or dispose of the material.
Do not allow material to enter sewers, a body of water, or contact the ground. Refer to RCRA 40 CFR 261, and/or any other
appropriate federal, state or local requirements for proper classification information.
TRANSPORT INFORMATION14
Non DOT/Non RCRA regulated
REGULATORY INFORMATION15
Component (CAS#) [%] – CODES
—————————————————————-
Proprietary polyol blend (0) [85-95%] IARC
Regulatory CODE Descriptions
—————————————————————-
IARC = IARC Carcinogen Risks
OTHER INFORMATION16
Disclaimer:
Although reasonable care has been taken in the preparation of this document, we extend no warranties and make no
representations as to the accuracy or completeness of the information contained herein, and assume no responsibility
regarding the suitability of this information for the user’s intended purposes or for the consequences of its use. Each individual
should make a determination as to the suitability of the information for their particular purpose(s).
1
1
0
X
1
1
None
0
Health = 1, Fire = 1, Reactivity = 0, Specific Hazard = None
Health = 1, Fire = 1, Physical Hazard = 0
X – Consult your supervisor for special instructions
NFPA:
HMIS III:
HMIS PPE:
Revision Date: 3/22/2017SDS Number: RF02.5-B-30000-S45 CA Page 4 of 4