3M MATERIAL SAFETY DATA SHEET 3M(TM) Finesse -It Finishing Material Easy Clean Up PN 051144-13084, 051144-81235,
051144-83058, 051144-83483, 051144-83985 06/07/2007
__________________________________________ _______________________________________________________
Page 1of 8
Material Safety Data Sheet
Copyright, 2007, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M(TM) Finesse-It Finishing Material Easy Clean Up PN 051144-13084, 051144-81235,
051144-83058, 051144-83483, 051144-83985
MANUFACTURER: 3M
DIVISION: Abrasives Systems Division
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 06/07/2007
Supercedes Date: 06/11/2006
Document Group:11-3626-6
Product Use:
Intended Use: Automotive
Specific Use: Automotive Finishing Material
SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by Wt
WATER 7732-18-5 40 -70
HYDROTREATED HEAVY NAPHTHA (PETROLEUM) 64742-48-9 7 -13
MEDIUM ALIPHATIC SOLVENT NAPHTHA 64742-88-7 7 -13
DISTILLATES (PETROLEUM), ACID TREATED, LIGHT 64742-14-9 5 -10
ALUMINUM OXIDE 1344-28-1 5 -10
GLYCERIN 56-81-5 3 -7
WHITE MINERAL OIL (PETROLEUM) 8042-47-5 1 -5
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: little odor,white, creamy thick liquid
General Physical Form: Liquid
Immediate health, physical, and environmental hazards: Closed containers exposed to heat from fire may build pressure and
explode. Vapors may travel long distances along the ground orfloor to an ignition source and flash back. May cause
3M MATERIAL SAFETY DATA SHEET 3M(TM) Finesse -It Finishing Material Easy Clean Up PN 051144-13084, 051144-81235,
051144-83058, 051144-83483, 051144-83985 06/07/2007
__________________________________________ _______________________________________________________
Page 2of 8
target organ effects.
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
Mild Eye Irritation: Signs/symptoms may include redness, pain, and tearing.
Skin Contact:
Mild Skin Irritation: Signs/symptoms may include localized redness, swelling, and itching.
Inhalation:
Intentional concentration and inhalation may be harmful or fatal.
Upper Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose
and throat pain.
During grinding, scraping, sanding:
Pneumoconiosis: Sign/symptoms may include persistent cough, breathlessness, chest pain, increased amounts of sputum, and
changes in lung function tests.
Maybe absorbed following inhalation and cause target organ effects.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, nausea, diarrhea and vomiting.
Maybe absorbed following ingestion and cause target organ effects.
Target Organ Effects:
Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea,
slowed reaction time, slurred speech, giddiness, and unconsciousness.
SECTION 4: FIRST AIDMEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention.
Skin Contact: Wash affected area with soap and water. If signs/symptoms develop, get medical attention.
Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention.
3M MATERIAL SAFETY DATA SHEET 3M(TM) Finesse -It Finishing Material Easy Clean Up PN 051144-13084, 051144-81235,
051144-83058, 051144-83483, 051144-83985 06/07/2007
__________________________________________ _______________________________________________________
Page 3of 8
If Swallowed: Do not induce vomiting. Give victim two glasses of water. Never give anything by mouth to an unconscious
person. Get immediate medical attention.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Autoignition temperature No Data Available
Flash Point >=200.00 F [Test Method: Tagliabue Closed Cup]
[Details: CONDITIONS: FLAME APPLIED AT 2
DEGREE INTERVALS]
Flammable Limits -LEL 0.80 %
Flammable Limits -UEL 6.00 %
5.2 EXTINGUISHING MEDIA
Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Water may not effectively extinguish fire; however, it should be used to keep fire-exposed
containers and surfaces cool and prevent explosive rupture. Wear full protective equipment (Bunker Gear) and a self-contained
breathing apparatus (SCBA).
Unusual Fire and Explosion Hazards: Not applicable. Closed containers exposed to heat from fire may build pressure and
explode. Vapors may travel long distances along the ground or floor to an ignition source and flash back.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures:Observe precautions from other sections. Call 3M-HELPS line (1-800-364-3577) for more
information on handling and managing the spill. Evacuate unprotected and untrained personnel from hazard area. The spill should be
cleaned up by qualified personnel. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical
ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition
source and could cause flammable gases or vapors in the spill area to burn or explode. Contain spill. For larger spills, cover drains
and build dikes to prevent entry into sewer systems or bodies of water. Working from around the edges of the spill inward, cover with
bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry.
Collect as much of the spilled material as possible. Clean up residue with detergent and water. Place in a closed container approved
for transportation by appropriate authorities. Dispose of collected material as soon as possible.
In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
Avoid eye contact. Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Avoid
breathing of vapors, mists or spray. Avoid prolonged or repeated skin contact. Avoid breathing of dust. Avoid eye contact with
3M MATERIAL SAFETY DATA SHEET 3M(TM) Finesse -It Finishing Material Easy Clean Up PN 051144-13084, 051144-81235,
051144-83058, 051144-83483, 051144-83985 06/07/2007
__________________________________________ _______________________________________________________
Page 4of 8
vapors, mists, or spray. Keep out ofthe reach of children. Avoid contact with oxidizing agents.
7.2 STORAGE
Keep container tightly closed. Store away from flammable and combustible materials. Store away from oxidizing agents. Keep from
freezing.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Use with appropriate local exhaust ventilation. If exhaust ventilation is not available, use appropriate respiratory protection.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact. Avoid eye contact with vapors, mists, or spray.
The following eye protection(s) are recommended: Safety Glasses with side shields, Indirect Vented Goggles.
8.2.2 Skin Protection
Avoid skin contact.
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with
your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Gloves made from the following material(s) are recommended: Neoprene, Nitrile Rubber.
8.2.3 Respiratory Protection
Avoid breathing of vapors, mists or spray. Avoid breathing of dust. Consult the current 3M Respirator Selection Guide for additional
information or call 1-800-243-4630 for 3M technical assistance.
Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with
OSHA regulations: Half facepiece or fullface air-purifyingrespirator with P95 particulate filters. Consult the current 3M
RespiratorySelection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of Swallowing
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
8.3 EXPOSURE GUIDELINES
Ingredient AuthorityType Limit Additional Information
ALUMINUM OXIDE ACGIH TWA, particulate
matter, < 1%
crystalline silica
10 mg/m3 Table A4
ALUMINUM OXIDE CMRG TWA 1 fiber/cc
ALUMINUM OXIDE OSHA TWA, respirable5 mg/m3 Table Z-1
ALUMINUM OXIDE OSHA TWA, Vacated, as
dust
10 mg/m3
ALUMINUM OXIDE OSHA TWA, as total dust15 mg/m3 Table Z-1
GLYCERIN ACGIH TWA, as mist 10 mg/m3
GLYCERIN OSHA TWA, as mist,
respirable
5 mg/m3 Table Z-1
GLYCERIN OSHA TWA, Vacated, as
mist, total dust
10 mg/m3
GLYCERIN OSHA TWA, as mist, total
dust
15 mg/m3 Table Z-1
HYDROTREATED HEAVY NAPHTHA
(PETROLEUM)
3M TWA 100 ppm
3M MATERIAL SAFETY DATA SHEET 3M(TM) Finesse -It Finishing Material Easy Clean Up PN 051144-13084, 051144-81235,
051144-83058, 051144-83483, 051144-83985 06/07/2007
__________________________________________ _______________________________________________________
Page 5of 8
HYDROTREATED HEAVY NAPHTHA
(PETROLEUM)
CMRG TWA 300 ppm
MEDIUM ALIPHATIC SOLVENT
NAPHTHA
CMRG TWA 100 ppm
OIL MIST, MINERAL ACGIH TWA, as mist 5 mg/m3
OIL MIST, MINERAL ACGIH STEL, as mist 10 mg/m3
OIL MIST, MINERAL OSHA TWA, as mist 5 mg/m3 Table Z-1
WHITE MINERAL OIL (PETROLEUM) CMRG TWA 5 mg/m3
WHITE MINERAL OIL (PETROLEUM) CMRG STEL 10 mg/m3
VAC Vacated PEL:Vacated Permissible Exposure Limits [PEL] are enforced as the OSHA PEL in some states. Check with your local
regulatoryagency.
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG : Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Odor, Color, Grade: little odor,white, creamy thick liquid
General Physical Form: Liquid
Autoignition temperature No Data Available
Flash Point >=200.00 F [Test Method: Tagliabue Closed Cup] [Details:
CONDITIONS: FLAME APPLIED AT 2 DEGREE INTERVALS]
Flammable Limits -LEL 0.80 %
Flammable Limits -UEL 6.00 %
Boiling point 212.00 F
Density .960 -.990 kg/l
Vapor Density 1.00 [Ref Std: AIR=1] [Details: Air = 1]
Vapor Pressure No Data Available
Specific Gravity 0.960 -0.990 [Ref Std: WATER=1]
Melting point No Data Available
Solubility In Water Not Applicable
Solubility in Water Negligible
Evaporation rate 4.40 [Ref Std: ETHER=1]
Hazardous Air Pollutants 0.069 % weight
Volatile Organic Compounds 200.27 g/l [Test Method: South Cost Air Qual Mgmt Dist] [Details:
CONDITIONS: Rule 443.1, calculated]
Percent volatile 70.00 %
VOC Less H2O & Exempt Solvents 554.89 g/l [Test Method: South Cost Air Qual Mgmt Dist] [Details:
CONDITIONS: Rule 443.1, calculated]
Viscosity 10000 -16500 centipoise
SECTION 10: STABILITY AND REACTIVITY
Stability:Stable.
Materials and Conditions to Avoid: Strong oxidizing agents
3M MATERIAL SAFETY DATA SHEET 3M(TM) Finesse -It Finishing Material Easy Clean Up PN 051144-13084, 051144-81235,
051144-83058, 051144-83483, 051144-83985 06/07/2007
__________________________________________ _______________________________________________________
Page 6of 8
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products
SubstanceCondition
Carbon monoxide Not Specified
Carbon dioxide Not Specified
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMICAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Incinerate in an industrial or commercial facility in the presence of a combustible material. As a disposal
alternative, dispose of waste product in a facility permitted to accept chemical waste.
EPA Hazardous Waste Number (RCRA):Not regulated
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
ID Number(s):
LA-B100-0352-3, 60-2000-0606-6, 60-9800-1329-0, 60-9800-1411-6, 60-9800-1927-1, 60-9800-1998-2, 60-9800-2187-1
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this
material.
SECTION 15: REGULATORY INFORMATION
3M MATERIAL SAFETY DATA SHEET 3M(TM) Finesse -It Finishing Material Easy Clean Up PN 051144-13084, 051144-81235,
051144-83058, 051144-83483, 051144-83985 06/07/2007
__________________________________________ _______________________________________________________
Page 7of 8
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard -No Pressure Hazard -No Reactivity Hazard -No Immediate Hazard -Yes Delayed Hazard -Yes
STATE REGULATIONS
Contact 3M for more information.
CHEMICAL INVENTORIES
The components of this product are in compliance with the chemical notification requirements of TSCA.
All applicable chemical ingredients in this material are listed on the European Inventory of Existing Chemical Substances (EINECS),
orare exempt polymers whose monomers are listed on EINECS.
Contact3M for more information.
INTERNATIONAL REGULATIONS
Contact 3M for more information.
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health: 1 Flammability: 1 Reactivity: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion ordecomposition products that are known to
be generated in significant quantities.
Reason for Reissue: The MSDS has been revised because 3M has adopted the 16-section ANSI/ISO format. The potential hazards
of the product have not changed. We encourage you to reread the MSDS and review the information.
Revision Changes:
Section 1: Product use information was modified.
Copyright was modified.
3M MATERIAL SAFETY DATA SHEET 3M(TM) Finesse -It Finishing Material Easy Clean Up PN 051144-13084, 051144-81235,
051144-83058, 051144-83483, 051144-83985 06/07/2007
__________________________________________ _______________________________________________________
Page 8of 8
Section 14: ID Number(s) was modified.
DISCLAIMER: The information in this Material Safety DataSheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user’s method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user’s knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user’s method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
3M MSDSs are available at www.3M.com