DURAGLAS FIBERGLASS REINFORCED FILLER
Not available.
Liquid.
(888) 345-5732
SAFETY DATA SHEET
Product name
Other means of
identification
Product type
Emergency telephone
number of the company
Section 1. Identification
:
:
:
:
Manufacturer :U.S. CHEMICAL & PLASTICS
600 Nova Dr. S.E.
Massillon, OH 44646
USA
Relevant identified uses of the substance or mixture and uses advised against
Paint or paint related material.
24035
24035Product code :
Product Information
Telephone Number
:(330) 830-6000
Transportation Emergency
Telephone Number
:(800) 424-9300
Section 2. Hazards identification
FLAMMABLE LIQUIDS – Category 3
ACUTE TOXICITY (inhalation) – Category 4
SKIN CORROSION/IRRITATION – Category 2
SERIOUS EYE DAMAGE/ EYE IRRITATION – Category 2A
SKIN SENSITIZATION – Category 1
CARCINOGENICITY – Category 1B
TOXIC TO REPRODUCTION – Category 2
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) – Category 1
ASPIRATION HAZARD – Category 1
Classification of the
substance or mixture
:
Signal word :Danger
Hazard pictograms :
GHS label elements
Percentage of the mixture consisting of ingredient(s) of unknown acute toxicity: 17.3%
(oral), 30.8% (dermal), 17.3% (inhalation)
OSHA/HCS status :This material is considered hazardous by the OSHA Hazard Communication Standard
(29 CFR 1910.1200).
Date of issue/Date of revision :1/13/2025Date of previous issue :12/13/2024 Version:15 1/16
24035 DURAGLAS FIBERGLASS REINFORCED FILLER SHW-85-NA-GHS-US
Section 2. Hazards identification
Precautionary statements
Prevention :Obtain special instructions before use. Do not handle until all safety precautions have
been read and understood. Wear protective gloves, protective clothing and eye or face
protection. Keep away from heat, hot surfaces, sparks, open flames and other ignition
sources. No smoking. Use explosion-proof electrical, ventilating or lighting equipment.
Use non-sparking tools. Take action to prevent static discharges. Keep container
tightly closed. Use only outdoors or in a well-ventilated area. Do not breathe vapor. Do
not eat, drink or smoke when using this product. Wash thoroughly after handling.
Contaminated work clothing must not be allowed out of the workplace.
Response :IF exposed or concerned: Get medical advice or attention. IF INHALED: Remove
person to fresh air and keep comfortable for breathing. Call a POISON CENTER or
doctor if you feel unwell. IF SWALLOWED: Immediately call a POISON CENTER or
doctor. Do NOT induce vomiting. IF ON SKIN (or hair): Take off immediately all
contaminated clothing. Rinse skin with water. Wash contaminated clothing before
reuse. IF ON SKIN: Wash with plenty of water. If skin irritation or rash occurs: Get
medical advice or attention. IF IN EYES: Rinse cautiously with water for several
minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye
irritation persists: Get medical advice or attention.
Storage :Store locked up. Store in a well-ventilated place. Keep cool.
Disposal Dispose of contents and container in accordance with all local, regional, national and
international regulations.
Hazards not otherwise
classified
:DANGER: Rags, steel wool, other waste soaked with this product, and sanding residue
may spontaneously catch fire if improperly discarded. Immediately place rags, steel
wool, other waste soaked with this product, and sanding residue in a sealed, water-filled,
metal container. Dispose of in accordance with local fire regulations.
Flammable liquid and vapor.
May be fatal if swallowed and enters airways.
Causes skin irritation.
May cause an allergic skin reaction.
Causes serious eye irritation.
Harmful if inhaled.
May cause cancer.
Suspected of damaging fertility or the unborn child.
Causes damage to organs through prolonged or repeated exposure. (hearing organs,
lungs)
:Hazard statements
Please refer to the SDS for additional information. Keep out of reach of children. Do not
transfer contents to other containers for storage.
Supplemental label
elements
DELAYED EFFECTS FROM LONG TERM OVEREXPOSURE. Contains solvents which
can cause permanent brain and nervous system damage. Intentional misuse by
deliberately concentrating and inhaling the contents can be harmful or fatal. WARNING:
This product contains chemicals known to the State of California to cause cancer and
birth defects or other reproductive harm. FOR PROFESSIONAL USE ONLY. This
product must be mixed with other components before use. Before opening the
packages, READ AND FOLLOW WARNING LABELS ON ALL COMPONENTS.
:
Section 3. Composition/information on ingredients
Other means of
identification
:Not available.
Substance/mixture
CAS number/other identifiers
:Mixture
Date of issue/Date of revision :1/13/2025Date of previous issue :12/13/2024 Version:15 2/16
24035 DURAGLAS FIBERGLASS REINFORCED FILLER SHW-85-NA-GHS-US
Section 3. Composition/information on ingredients
Talc 25 – 50 14807-96-6
Unsaturated Polyester 10 – 25 –
Styrene 10 – <20 100-42-5
Magnesium Carbonate 10 - 25 546-93-0
Wollastonite 10 13983-17-0
Calcium Carbonate 10 471-34-1
Ingredient name CAS number% by weight
Occupational exposure limits, if available, are listed in Section 8.
Any concentration shown as a range is to protect confidentiality or is due to batch variation.
There are no additional ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified and hence require reporting in this section.
Get medical attention immediately. Call a poison center or physician. Wash out mouth
with water. Remove dentures if any. If material has been swallowed and the exposed
person is conscious, give small quantities of water to drink. Stop if the exposed person
feels sick as vomiting may be dangerous. Aspiration hazard if swallowed. Can enter
lungs and cause damage. Do not induce vomiting. If vomiting occurs, the head should
be kept low so that vomit does not enter the lungs. Never give anything by mouth to an
unconscious person. If unconscious, place in recovery position and get medical
attention immediately. Maintain an open airway. Loosen tight clothing such as a collar,
tie, belt or waistband.
Immediately flush eyes with plenty of water, occasionally lifting the upper and lower
eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10
minutes. Get medical attention.
Wash with plenty of soap and water. Remove contaminated clothing and shoes. Wash
contaminated clothing thoroughly with water before removing it, or wear gloves.
Continue to rinse for at least 10 minutes. Get medical attention. In the event of any
complaints or symptoms, avoid further exposure. Wash clothing before reuse. Clean
shoes thoroughly before reuse.
Remove victim to fresh air and keep at rest in a position comfortable for breathing. If it
is suspected that fumes are still present, the rescuer should wear an appropriate mask
or self-contained breathing apparatus. If not breathing, if breathing is irregular or if
respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It
may be dangerous to the person providing aid to give mouth-to-mouth resuscitation.
Get medical attention. If necessary, call a poison center or physician. If unconscious,
place in recovery position and get medical attention immediately. Maintain an open
airway. Loosen tight clothing such as a collar, tie, belt or waistband.
Section 4. First aid measures
Eye contact
Skin contact
Inhalation
Ingestion :
:
:
:
Description of necessary first aid measures
Most important symptoms/effects, acute and delayed
Inhalation :Harmful if inhaled.
May be fatal if swallowed and enters airways.:Ingestion
Skin contact :Causes skin irritation. May cause an allergic skin reaction.
Causes serious eye irritation.:Eye contact
Over-exposure signs/symptoms
Eye contact :Adverse symptoms may include the following:
pain or irritation
watering
redness
Potential acute health effects
Date of issue/Date of revision :1/13/2025Date of previous issue :12/13/2024 Version:15 3/16
24035 DURAGLAS FIBERGLASS REINFORCED FILLER SHW-85-NA-GHS-US
Section 4. First aid measures
Protection of first-aiders:No action shall be taken involving any personal risk or without suitable training. If it is
suspected that fumes are still present, the rescuer should wear an appropriate mask or
self-contained breathing apparatus. It may be dangerous to the person providing aid to
give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with water
before removing it, or wear gloves.
Notes to physician :Treat symptomatically. Contact poison treatment specialist immediately if large
quantities have been ingested or inhaled.
Specific treatments :No specific treatment.
Skin contact
Ingestion
Inhalation Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
nausea or vomiting
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
irritation
redness
reduced fetal weight
increase in fetal deaths
skeletal malformations
:
:
:
See toxicological information (Section 11)
Indication of immediate medical attention and special treatment needed, if necessary
Section 5. Fire-fighting measures
Promptly isolate the scene by removing all persons from the vicinity of the incident if
there is a fire. No action shall be taken involving any personal risk or without suitable
training. Move containers from fire area if this can be done without risk. Use water
spray to keep fire-exposed containers cool.
Hazardous thermal
decomposition products
Specific hazards arising
from the chemical
Decomposition products may include the following materials:
carbon dioxide
carbon monoxide
metal oxide/oxides
Flammable liquid and vapor. Runoff to sewer may create fire or explosion hazard. In a
fire or if heated, a pressure increase will occur and the container may burst, with the risk
of a subsequent explosion. The vapor/gas is heavier than air and will spread along the
ground. Vapors may accumulate in low or confined areas or travel a considerable
distance to a source of ignition and flash back.
Fire-fighters should wear appropriate protective equipment and self-contained breathing
apparatus (SCBA) with a full face-piece operated in positive pressure mode.
Special protective
equipment for fire-fighters
Use dry chemical, CO , water spray (fog) or foam.
Extinguishing media
:
:
:
Flammable liquid.Remark :
Do not use water jet.
Suitable extinguishing
media
:
Unsuitable extinguishing
media
:
Special protective actions
for fire-fighters
:
Date of issue/Date of revision :1/13/2025Date of previous issue :12/13/2024 Version:15 4/16
24035 DURAGLAS FIBERGLASS REINFORCED FILLER SHW-85-NA-GHS-US
Section 6. Accidental release measures
Environmental precautions
Personal precautions, protective equipment and emergency procedures
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Approach release from upwind. Prevent entry into sewers,
water courses, basements or confined areas. Wash spillages into an effluent treatment
plant or proceed as follows. Contain and collect spillage with non-combustible,
absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in
container for disposal according to local regulations (see Section 13). Dispose of via a
licensed waste disposal contractor. Contaminated absorbent material may pose the
same hazard as the spilled product. Note: see Section 1 for emergency contact
information and Section 13 for waste disposal.
:
:No action shall be taken involving any personal risk or without suitable training.
Evacuate surrounding areas. Keep unnecessary and unprotected personnel from
entering. Do not touch or walk through spilled material. Shut off all ignition sources.
No flares, smoking or flames in hazard area. Avoid breathing vapor or mist. Provide
adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put
on appropriate personal protective equipment.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains
and sewers. Inform the relevant authorities if the product has caused environmental
pollution (sewers, waterways, soil or air).
Large spill :
Stop leak if without risk. Move containers from spill area. Use spark-proof tools and
explosion-proof equipment. Dilute with water and mop up if water-soluble. Alternatively,
or if water-insoluble, absorb with an inert dry material and place in an appropriate waste
disposal container. Dispose of via a licensed waste disposal contractor.
Small spill :
Methods and materials for containment and cleaning up
For non-emergency
personnel
For emergency responders:If specialized clothing is required to deal with the spillage, take note of any information in
Section 8 on suitable and unsuitable materials. See also the information in "For non-
emergency personnel".
Section 7. Handling and storage
Advice on general
occupational hygiene
Eating, drinking and smoking should be prohibited in areas where this material is
handled, stored and processed. Workers should wash hands and face before eating,
drinking and smoking. Remove contaminated clothing and protective equipment before
entering eating areas. See also Section 8 for additional information on hygiene
measures.
:
Protective measures Put on appropriate personal protective equipment (see Section 8). Persons with a
history of skin sensitization problems should not be employed in any process in which
this product is used. Avoid exposure - obtain special instructions before use. Avoid
exposure during pregnancy. Do not handle until all safety precautions have been read
and understood. Do not get in eyes or on skin or clothing. Do not breathe vapor or mist.
Do not swallow. Use only with adequate ventilation. Wear appropriate respirator when
ventilation is inadequate. Do not enter storage areas and confined spaces unless
adequately ventilated. Keep in the original container or an approved alternative made
from a compatible material, kept tightly closed when not in use. Store and use away
from heat, sparks, open flame or any other ignition source. Use explosion-proof
electrical (ventilating, lighting and material handling) equipment. Use only non-sparking
tools. Take precautionary measures against electrostatic discharges. Empty containers
retain product residue and can be hazardous. Do not reuse container.
:
Precautions for safe handling
Date of issue/Date of revision :1/13/2025Date of previous issue :12/13/2024 Version:15 5/16
24035 DURAGLAS FIBERGLASS REINFORCED FILLER SHW-85-NA-GHS-US
Section 7. Handling and storage
Conditions for safe storage,
including any
incompatibilities
Store in accordance with local regulations. Store in a segregated and approved area.
Store in original container protected from direct sunlight in a dry, cool and well-ventilated
area, away from incompatible materials (see Section 10) and food and drink. Store
locked up. Eliminate all ignition sources. Separate from oxidizing materials. Keep
container tightly closed and sealed until ready for use. Containers that have been
opened must be carefully resealed and kept upright to prevent leakage. Do not store in
unlabeled containers. Use appropriate containment to avoid environmental
contamination. See Section 10 for incompatible materials before handling or use.
:
Talc 14807-96-6 NIOSH REL (United States, 10/2020).
TWA: 2 mg/m 10 hours. Form: Respirable
fraction
ACGIH TLV (United States, 1/2024).
TWA: 2 mg/m 8 hours. Form: Respirable
fraction
Unsaturated Polyester None.
Styrene 100-42-5 ACGIH TLV (United States, 1/2024).
Ototoxicant.
TWA: 10 ppm 8 hours.
STEL: 20 ppm 15 minutes.
OSHA PEL Z2 (United States, 2/2013).
TWA: 100 ppm 8 hours.
CEIL: 200 ppm
AMP: 600 ppm 5 minutes.
NIOSH REL (United States, 10/2020).
TWA: 50 ppm 10 hours.
TWA: 215 mg/m 10 hours.
STEL: 100 ppm 15 minutes.
STEL: 425 mg/m 15 minutes.
Magnesium Carbonate 546-93-0 NIOSH REL (United States, 10/2020).
TWA: 5 mg/m 10 hours. Form: Respirable
fraction
TWA: 10 mg/m 10 hours. Form: Total
OSHA PEL (United States, 5/2018).
TWA: 5 mg/m 8 hours. Form: Respirable
fraction
TWA: 15 mg/m 8 hours. Form: Total dust
Wollastonite 13983-17-0 ACGIH TLV (United States, 1/2024).
TWA: 1 mg/m 8 hours. Form: Inhalable
fraction
Calcium Carbonate 471-34-1 NIOSH REL (United States, 10/2020).
[calcium carbonate]
TWA: 5 mg/m 10 hours. Form: Respirable
fraction
TWA: 10 mg/m 10 hours. Form: Total
Section 8. Exposure controls/personal protection
Ingredient name Exposure limits
Control parameters
Occupational exposure limits (OSHA United States)
Occupational exposure limits (Canada)
CAS #
Date of issue/Date of revision :1/13/2025Date of previous issue :12/13/2024 Version:15 6/16
24035 DURAGLAS FIBERGLASS REINFORCED FILLER SHW-85-NA-GHS-US
Section 8. Exposure controls/personal protection
talc (none asbestiform) 14807-96-6 CA British Columbia Provincial (Canada,
8/2023). Notes: the value is for particulate
matter containing no asbestos and less
than 1% crystalline silica.
TWA: 2 mg/m 8 hours. Form: Respirable
CA Alberta Provincial (Canada, 3/2023).
OEL: 2 mg/m 8 hours. Form: Respirable
particulate
CA Ontario Provincial (Canada, 6/2019).
TWA: 2 mg/m 8 hours. Form: Respirable
particulate matter.
TWA: 2 f/cc 8 hours.
CA Quebec Provincial (Canada, 2/2024).
TWAEV: 2 mg/m 8 hours. Form: respirable
aerosol fraction
CA Saskatchewan Provincial (Canada,
4/2021).
TWA: 2 mg/m 8 hours. Form: respirable
fraction
Vinyl benzene 100-42-5 CA Alberta Provincial (Canada, 3/2023).
OEL: 40 ppm 15 minutes.
OEL: 170 mg/m 15 minutes.
OEL: 85 mg/m 8 hours.
OEL: 20 ppm 8 hours.
CA British Columbia Provincial (Canada,
8/2023).
TWA: 20 ppm 8 hours.
STEL: 40 ppm 15 minutes.
CA Ontario Provincial (Canada, 6/2019).
TWA: 35 ppm 8 hours.
STEL: 100 ppm 15 minutes.
CA Quebec Provincial (Canada, 2/2024).
TWAEV: 50 ppm 8 hours.
STEV: 75 ppm 15 minutes.
CA Saskatchewan Provincial (Canada,
4/2021).
STEL: 40 ppm 15 minutes.
TWA: 20 ppm 8 hours.
Ingredient name Exposure limits
Styrene 100-42-5 NOM-010-STPS-2014 (Mexico, 4/2016).
TWA: 20 ppm 8 hours.
STEL: 40 ppm 15 minutes.
N,N-dimethylaniline 121-69-7 NOM-010-STPS-2014 (Mexico, 4/2016).
Absorbed through skin.
TWA: 5 ppm 8 hours.
STEL: 10 ppm 15 minutes.
Exposure limits
Occupational exposure limits (Mexico)
CAS #
CAS #
Biological exposure indices (United States)
Date of issue/Date of revision :1/13/2025Date of previous issue :12/13/2024 Version:15 7/16
24035 DURAGLAS FIBERGLASS REINFORCED FILLER SHW-85-NA-GHS-US
Section 8. Exposure controls/personal protection
Safety eyewear complying with an approved standard should be used when a risk
assessment indicates this is necessary to avoid exposure to liquid splashes, mists,
gases or dusts. If contact is possible, the following protection should be worn, unless
the assessment indicates a higher degree of protection: chemical splash goggles.
Eye/face protection :
Emissions from ventilation or work process equipment should be checked to ensure
they comply with the requirements of environmental protection legislation. In some
cases, fume scrubbers, filters or engineering modifications to the process equipment
will be necessary to reduce emissions to acceptable levels.
Appropriate engineering
controls
:Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or
other engineering controls to keep worker exposure to airborne contaminants below any
recommended or statutory limits. The engineering controls also need to keep gas,
vapor or dust concentrations below any lower explosive limits. Use explosion-proof
ventilation equipment.
Wash hands, forearms and face thoroughly after handling chemical products, before
eating, smoking and using the lavatory and at the end of the working period.
Appropriate techniques should be used to remove potentially contaminated clothing.
Contaminated work clothing should not be allowed out of the workplace. Wash
contaminated clothing before reusing. Ensure that eyewash stations and safety
showers are close to the workstation location.
Hygiene measures :
Individual protection measures
Skin protection
Environmental exposure
controls
:
Styrene ACGIH BEI (United States, 1/2024)
BEI: 150 mg/g creatinine, mandelic acid plus
phenylglyoxylic acid [in urine]. Sampling time:
end of shift.
BEI: 20 g/l, styrene [in urine]. Sampling time:
end of shift.
Ingredient name Exposure indices
Biological exposure indices (Canada)
Biological exposure indices (Mexico)
No exposure indices known.
Styrene Official Mexican STANDARD NOM-
047-SSA1-2011, Environmental Health-
Biological exposure indices for personnel
occupationally exposed to chemical
substances. (Mexico, 6/2012)
BEI: 0.2 mg/L [semi-quantitative.The
biological determinant is an indicator of
chemical exposure, but the quantitative
interpretation of the measure is ambiguous.
These biological determinants should be used
as a screening test if a quantitative test is not
possible.], styrene [in venous blood]. Sampling
time: at the end of the work shift.
BEI: 400 mg/g creatinine [non-specific.The
determinant is nonspecific, since it can be
found after exposure to other chemicals.],
mandelic Acid plus Phenylglyoxylic Acid [in
urine]. Sampling time: at the end of the work
shift.
Ingredient name Exposure indices
Date of issue/Date of revision :1/13/2025Date of previous issue :12/13/2024 Version:15 8/16
24035 DURAGLAS FIBERGLASS REINFORCED FILLER SHW-85-NA-GHS-US
Section 8. Exposure controls/personal protection
Hand protection
Based on the hazard and potential for exposure, select a respirator that meets the
appropriate standard or certification. Respirators must be used according to a
respiratory protection program to ensure proper fitting, training, and other important
aspects of use.
Chemical-resistant, impervious gloves complying with an approved standard should be
worn at all times when handling chemical products if a risk assessment indicates this is
necessary. Considering the parameters specified by the glove manufacturer, check
during use that the gloves are still retaining their protective properties. It should be
noted that the time to breakthrough for any glove material may be different for different
glove manufacturers. In the case of mixtures, consisting of several substances, the
protection time of the gloves cannot be accurately estimated.
Respiratory protection :
:
Body protection Personal protective equipment for the body should be selected based on the task being
performed and the risks involved and should be approved by a specialist before
handling this product. When there is a risk of ignition from static electricity, wear anti-
static protective clothing. For the greatest protection from static discharges, clothing
should include anti-static overalls, boots and gloves.
:
Other skin protection :Appropriate footwear and any additional skin protection measures should be selected
based on the task being performed and the risks involved and should be approved by a
specialist before handling this product.
Section 9. Physical and chemical properties
Physical state
Melting point/freezing point
Vapor pressure
Relative density
Liquid.
Not available.
1.66
3.6 [Air = 1]
Not available.Odor
pH
Green.Color
Evaporation rate 0.49 (butyl acetate = 1)
Auto-ignition temperature
Flash point
Not available.
Closed cup: 29 C (84.2 F) [Pensky-Martens Closed Cup]
Not applicable.
Not applicable.
Viscosity Kinematic (40 C (104 F)): <20.5 mm
2
/s (<20.5 cSt)
Not available.Odor threshold
Partition coefficient: n-
octanol/water
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Appearance
:145 C (293 F)
:Flammable liquid.
:Lower: 1.1%
Upper: 6.1%
Decomposition temperature:Not available.
Molecular weight :Not applicable.
Boiling point, initial boiling
point, and boiling range
Flammability
Lower and upper explosion
limit/flammability limit
Relative vapor density
The conditions of measurement of all properties are at standard temperature and pressure unless otherwise indicated.
0.57 kPa (4.3 mm Hg)
Solubility(ies) :
Media Result
cold water Not soluble
Date of issue/Date of revision :1/13/2025Date of previous issue :12/13/2024 Version:15 9/16
24035 DURAGLAS FIBERGLASS REINFORCED FILLER SHW-85-NA-GHS-US
Section 9. Physical and chemical properties
Heat of combustion :5.88 kJ/g
Section 10. Stability and reactivity
Hazardous decomposition
products
Conditions to avoid Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld,
braze, solder, drill, grind or expose containers to heat or sources of ignition. Do not
allow vapor to accumulate in low or confined areas.
Under normal conditions of storage and use, hazardous decomposition products should
not be produced.
The product is stable.Chemical stability
Reactive or incompatible with the following materials:
oxidizing materials
:
:
:
Incompatible materials :
Possibility of hazardous
reactions
:Under normal conditions of storage and use, hazardous reactions will not occur.
Reactivity :No specific test data related to reactivity available for this product or its ingredients.
Section 11. Toxicological information
Acute toxicity
Styrene LC50 Inhalation Gas. Rat 2770 ppm 4 hours
LC50 Inhalation Vapor Rat 11800 mg/m 4 hours
LD50 Oral Rat 2650 mg/kg -
Magnesium Carbonate LD50 Oral Rat 8000 mg/kg -
Calcium Carbonate LD50 Oral Rat 6450 mg/kg -
Product/ingredient name Result Species Dose Exposure
Carcinogenicity
Not available.
Mutagenicity
Not available.
Irritation/Corrosion
Talc Skin - Mild irritant Human - 72 hours 300
ug I
-
Styrene Eyes - Mild irritant Human - 50 ppm -
Eyes - Moderate irritantRabbit - 24 hours 100
mg
-
Eyes - Severe irritantRabbit - 100 mg -
Skin - Mild irritant Rabbit - 500 mg -
Skin - Moderate irritantRabbit - 100 % -
Calcium Carbonate Eyes - Severe irritantRabbit - 24 hours 750
ug
-
Skin - Moderate irritantRabbit - 24 hours 500
mg
-
Product/ingredient name Result Score Exposure Observation
Sensitization
Not available.
Species
Information on toxicological effects
Date of issue/Date of revision :1/13/2025Date of previous issue :12/13/2024 Version:15 10/16
24035 DURAGLAS FIBERGLASS REINFORCED FILLER SHW-85-NA-GHS-US
Section 11. Toxicological information
Teratogenicity
Not available.
Reproductive toxicity
Not available.
Specific target organ toxicity (single exposure)
Specific target organ toxicity (repeated exposure)
Styrene Category 3 - Respiratory tract
irritation
Name Category
Name Category
Talc Category 1 inhalation lungs
Styrene Category 1 - hearing organs
Aspiration hazard
Name Result
Styrene ASPIRATION HAZARD - Category 1
Route of
exposure
Target organs
Route of
exposure
Target organs
Classification
Talc - 3 -
Styrene - 2A Reasonably anticipated to be a human carcinogen.
Wollastonite - 3 -
Product/ingredient name NTPIARCOSHA
Information on the likely
routes of exposure
Inhalation :Harmful if inhaled.
May be fatal if swallowed and enters airways.:Ingestion
Skin contact :Causes skin irritation. May cause an allergic skin reaction.
Causes serious eye irritation.:Eye contact
Symptoms related to the physical, chemical and toxicological characteristics
Skin contact
Inhalation Adverse symptoms may include the following:
reduced fetal weight
increase in fetal deaths
skeletal malformations
Adverse symptoms may include the following:
irritation
redness
reduced fetal weight
increase in fetal deaths
skeletal malformations
:
:
Eye contact :Adverse symptoms may include the following:
pain or irritation
watering
redness
:Not available.
Potential acute health effects
Date of issue/Date of revision :1/13/2025Date of previous issue :12/13/2024 Version:15 11/16
24035 DURAGLAS FIBERGLASS REINFORCED FILLER SHW-85-NA-GHS-US
Section 11. Toxicological information
Not available.
Causes damage to organs through prolonged or repeated exposure. Once sensitized, a
severe allergic reaction may occur when subsequently exposed to very low levels.
General :
May cause cancer. Risk of cancer depends on duration and level of exposure.Carcinogenicity :
No known significant effects or critical hazards.Mutagenicity :
Suspected of damaging the unborn child.Teratogenicity :
Developmental effects :No known significant effects or critical hazards.
Fertility effects :No known significant effects or critical hazards.
Ingestion Adverse symptoms may include the following:
nausea or vomiting
reduced fetal weight
increase in fetal deaths
skeletal malformations
:
Potential chronic health effects
Delayed and immediate effects and also chronic effects from short and long term exposure
Numerical measures of toxicity
Oral 16248.31 mg/kg
Inhalation (gases) 16984.08 ppm
Inhalation (vapors) 72.35 mg/l
Route ATE value
Acute toxicity estimates
Potential immediate
effects
:Not available.
Short term exposure
Potential delayed effects:Not available.
Potential immediate
effects
:Not available.
Long term exposure
Potential delayed effects:Not available.
Section 12. Ecological information
Toxicity
Styrene Acute EC50 1400 g/l Fresh water Algae - Raphidocelis subcapitata72 hours
Acute EC50 720 g/l Fresh water Algae - Raphidocelis subcapitata96 hours
Acute EC50 4700 g/l Fresh water Daphnia - Daphnia magna 48 hours
Acute LC50 52 mg/l Marine water Crustaceans - Artemia salina 48 hours
Acute LC50 4020 g/l Fresh water Fish - Pimephales promelas 96 hours
Chronic NOEC 63 g/l Fresh water Algae - Raphidocelis subcapitata96 hours
Calcium Carbonate Acute LC50 >56000 ppm Fresh water Fish – Gambusia affinis – Adult96 hours
Chronic NOEC 16.5 mg/l Fresh waterFish – Rhamdia quelen 30 days
Product/ingredient name SpeciesResult Exposure
Persistence and degradability
Not available.
Date of issue/Date of revision :1/13/2025Date of previous issue :12/13/2024 Version:15 12/16
24035 DURAGLAS FIBERGLASS REINFORCED FILLER SHW-85-NA-GHS-US
Section 12. Ecological information
LogPow BCF Potential
Bioaccumulative potential
Other adverse effects :No known significant effects or critical hazards.
Product/ingredient name
Styrene – 13.49 Low
Soil/water partition
coefficient (KOC)
:Not available.
Mobility in soil
Section 13. Disposal considerations
The generation of waste should be avoided or minimized wherever possible. Disposal
of this product, solutions and any by-products should at all times comply with the
requirements of environmental protection and waste disposal legislation and any
regional local authority requirements. Dispose of surplus and non-recyclable products
via a licensed waste disposal contractor. Waste should not be disposed of untreated to
the sewer unless fully compliant with the requirements of all authorities with jurisdiction.
Waste packaging should be recycled. Incineration or landfill should only be considered
when recycling is not feasible. This material and its container must be disposed of in a
safe way. Care should be taken when handling emptied containers that have not been
cleaned or rinsed out. Empty containers or liners may retain some product residues.
Vapor from product residues may create a highly flammable or explosive atmosphere
inside the container. Do not cut, weld or grind used containers unless they have been
cleaned thoroughly internally. Avoid dispersal of spilled material and runoff and contact
with soil, waterways, drains and sewers.
:Disposal methods
Section 14. Transport information
RESIN SOLUTION
3
III
RESIN SOLUTION
3
III
UN1866 UN1866
– Emergency
schedules F-E, S-
E
DOT
Classification
IMDG
UN number
UN proper
shipping name
Transport
hazard class(es)
Packing group
Additional
information
Environmental
hazards
No. No.
TDG
Classification
UN1866
RESIN SOLUTION
3
III
No.
Product classified
as per the
following sections
of the
Transportation of
Dangerous Goods
Regulations:
2.18-2.19 (Class
Mexico
Classification
UN1866
RESIN SOLUTION
3
III
No.
–
IATA
UN1866
RESIN
SOLUTION
3
III
No.
–
Date of issue/Date of revision :1/13/2025Date of previous issue :12/13/2024 Version:15 13/16
24035 DURAGLAS FIBERGLASS REINFORCED FILLER SHW-85-NA-GHS-US
Section 14. Transport information
Special precautions for user
Transport in bulk according
to IMO instruments
Not available.
:
Proper shipping name :
Not available.
:
3).
Multi-modal shipping descriptions are provided for informational purposes and do not
consider container sizes. The presence of a shipping description for a particular
mode of transport (sea, air, etc.), does not indicate that the product is packaged
suitably for that mode of transport. All packaging must be reviewed for suitability prior
to shipment, and compliance with the applicable regulations is the sole responsibility
of the person offering the product for transport. People loading and unloading
dangerous goods must be trained on all of the risks deriving from the substances
and on all actions in case of emergency situations.
127
ERG No.
127 127
ERG No. ERG No.
Section 15. Regulatory information
All data given below are MAXIMUM THEORETICAL VALUES based on the product AS CURRENTLY FORMULATED
and rely on information provided to us by our raw material suppliers. Our suppliers often provide an estimated value or
range less than a certain upper limit. We calculate MAXIMUM THEORETICAL VALUES using defined values, if provided,
or the upper limit reported by our supplier. Additionally, the suppliers information may include amounts present in the
product as unintentional byproducts or impurities. Variations may occur in individual batches due to adjustments made
during production. Reporting of chemicals in this section does not necessarily indicate their presence in the final
formulated product.
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other
reproductive harm.
California Prop. 65
Australia inventory (AIIC): Not determined.
China inventory (IECSC): Not determined.
Japan inventory (CSCL): Not determined.
Japan inventory (ISHL): Not determined.
Korea inventory (KECI): Not determined.
New Zealand Inventory of Chemicals (NZIoC): Not determined.
Philippines inventory (PICCS): Not determined.
Taiwan Chemical Substances Inventory (TCSI): Not determined.
Thailand inventory: Not determined.
International regulations
International lists :
Montreal Protocol
Not listed.
Stockholm Convention on Persistent Organic Pollutants
Not listed.
Lead (as Pb) 0.000009
Styrene 13 100-42-5
Ingredient name CAS number% by weight
SARA 313
Date of issue/Date of revision :1/13/2025Date of previous issue :12/13/2024 Version:15 14/16
24035 DURAGLAS FIBERGLASS REINFORCED FILLER SHW-85-NA-GHS-US
Section 15. Regulatory information
Turkey inventory: Not determined.
Vietnam inventory: Not determined.
Section 16. Other information
1/13/2025
History
Date of printing
Date of issue/Date of
revision
Version
Date of previous issue
:
:
:
:
Indicates information that has changed from previously issued version.
Key to abbreviations :
1/13/2025
12/13/2024
15
Hazardous Material Information System (U.S.A.)
3
3
0
*
Health
Flammability
Physical hazards
Caution: HMIS ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4
representing significant hazards or risks. Although HMIS ratings and the associated label are not required on
SDSs or products leaving a facility under 29 CFR 1910.1200, the preparer may choose to provide them. HMIS
ratings are to be used with a fully implemented HMIS program. HMIS is a registered trademark and service
mark of the American Coatings Association, Inc.
The customer is responsible for determining the PPE code for this material. For more information on HMIS
Personal Protective Equipment (PPE) codes, consult the HMIS Implementation Manual.
FLAMMABLE LIQUIDS – Category 3 On basis of test data
ACUTE TOXICITY (inhalation) – Category 4 Calculation method
SKIN CORROSION/IRRITATION – Category 2 Calculation method
SERIOUS EYE DAMAGE/ EYE IRRITATION – Category 2A Calculation method
SKIN SENSITIZATION – Category 1 Calculation method
CARCINOGENICITY – Category 1B Calculation method
TOXIC TO REPRODUCTION – Category 2 Calculation method
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) – Category 1 Calculation method
ASPIRATION HAZARD – Category 1 Calculation method
Procedure used to derive the classification
Classification Justification
Notice to reader
ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships, 1973
as modified by the Protocol of 1978. (“Marpol” = marine pollution)
N/A = Not available
SGG = Segregation Group
UN = United Nations
Date of issue/Date of revision :1/13/2025Date of previous issue :12/13/2024 Version:15 15/16
24035 DURAGLAS FIBERGLASS REINFORCED FILLER SHW-85-NA-GHS-US
Section 16. Other information
It is recommended that each customer or recipient of this Safety Data Sheet (SDS) study it carefully and consult
resources, as necessary or appropriate, to become aware of and understand the data contained in this SDS and
any hazards associated with the product. This information is provided in good faith and believed to be accurate
as of the effective date herein. However, no warranty, express or implied, is given. The information presented
here applies only to the product as shipped. The addition of any material can change the composition, hazards
and risks of the product. Products shall not be repackaged, modified, or tinted except as specifically instructed
by the manufacturer, including but not limited to the incorporation of products not specified by the manufacturer,
or the use or addition of products in proportions not specified by the manufacturer. Regulatory requirements
are subject to change and may differ between various locations and jurisdictions. The customer/buyer/user is
responsible to ensure that his activities comply with all country, federal, state, provincial or local laws. The
conditions for use of the product are not under the control of the manufacturer; the customer/buyer/user is
responsible to determine the conditions necessary for the safe use of this product. The customer/buyer/user
should not use the product for any purpose other than the purpose shown in the applicable section of this SDS
without first referring to the supplier and obtaining written handling instructions. Due to the proliferation of
sources for information such as manufacturer-specific SDS, the manufacturer cannot be responsible for SDSs
obtained from any other source.
Date of issue/Date of revision :1/13/2025Date of previous issue :12/13/2024 Version:15 16/16
24035 DURAGLAS FIBERGLASS REINFORCED FILLER SHW-85-NA-GHS-US