MATERIAL SAFETY DATA SHEET
Pro-Set Inc.
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME:…………………………………..PRO-SET
M1012 Resin
PRODUCT CODE:……………………………………M1012
CHEMICAL FAMILY:……………………………….Epoxy Resin.
CHEMICAL NAME:………………………………….Epoxy Resin.
FORMULA:……………………………………………..Not applicable.
MANUFACTURER: EMERG ENCY TELEPHONE NUMBERS:
Pro-Set Inc. Transportation
707 Martin Street CHEMTREC:………………800-424-9300 (U.S.)
Bay City, MI 48706-4143, U.S.A. 703-527-3887 (International)
Phone: 888-377-6738 or 989-671-4079 Non-transportation
www.prosetepoxy.com Poison Hotline:……………800-222-1222
2. COMPOSITION/INFORMATION ON HAZARDOUS INGREDIENTS
INGREDIENT NAME CAS # CONCENTRATION
Diglycidyl ether of Bisphenol-A 1675-54-3
Bisphenol-F type epoxy resin 28064-14-4
3. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
HMIS Hazard Rating: Health – 2 Flammability – 1 Physical Hazards – 0
CAUTION! Mild eye and skin irritant. May cause allergic reaction and sensitization. Clear, light-yellow liquid with mild odor.
PRIMARY ROUTE(S) OF ENTRY:………………………………………….Skin contact.
POTENTIAL HEALTH EFFECTS:
ACUTE INHALATION:………………………………………………………….Not likely to cause acute effects unless heated to high temperatures. If
product is heated, vapors generated can cause headache, nausea, dizziness and possible respiratory irritation if inhaled in high
concentrations.
CHRONIC INHALATION:………………………………………………………Not likely to cause chronic effects. Repeated exposure to high vapor
concentrations may cause irritation of pre-existing lung allergies and increase the chance of developing allergy symptoms to this product.
ACUTE SKIN CONTACT:……………………………………………………..May cause allergic skin response in certain individuals. May cause
moderate irritation to the skin such as redness and itching.
CHRONIC SKIN CONTACT:………………………………………………….May cause sensitization in susceptible individuals. May cause
moderate irritation to the skin.
EYE CONTACT:…………………………………………………………………..May cause irritation.
INGESTION:………………………………………………………………………..Low acute oral toxicity.
SYMPTOMS OF OVEREXPOSURE:………………………………………Possible sensitization and subsequent allergic reactions usually seen
as redness and rashes. Repeated exposure is not likely to cause other adverse health effects.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE:
Pre-existing skin and respiratory disorders may be aggravated by exposure to this product. Pre-existing lung and skin allergies may
increase the chance of developing allergic symptoms to this product.
4. FIRST AID MEASURES:
FIRST AID FOR EYES:…………………………………………………………Flush immediately with water for at least 15 minutes. Consult a
physician.
FIRST AID FOR SKIN:………………………………………………………….Remove contaminated clothing. Wipe excess from skin. Wash with
soap and water. If irritation occurs, get medical attention.
MSDS #M1012-08a Last Revised: 03JAN08
Pro-Set Inc. Page 2 of 4 PRO-SET
M1012 Resin
FIRST AID FOR INHALATION:……………………………………………..Remove to fresh air and rest if effects occur.
FIRST AID FOR INGESTION:………………………………………………..Seek medical attention if appreciable amounts are ingested.
5. FIRE FIGHTING MEASURES:
FLASH POINT:…………………………………………………………………….> 260 F (PMCC)
EXTINGUISHING MEDIA:……………………………………………………..Water fog, carbon dioxide (CO
2
) or dry chemical.
SPECIAL FIRE FIGHTING PROCEDURES:
Wear complete fire fighting gear and self-contained breathing apparatus. Cool fire-exposed containers with water spray. Material is not
readily combustible unless preheated.
FIRE AND EXPLOSION HAZARDS:………………………………………HAZARDOUS DECOMPOSITION PRODUCTS: During a fire, smoke
may contain the original materials in addition to combustion products of varying composition which may be toxic and/or irritating.
Combustion products may include, but are not limited to: phenolics, carbon monoxide, carbon dioxide.
6. ACCIDENTAL RELEASE MEASURES:
SPILL OR LEAK PROCEDURES: Stop leak without additional risk. Dike and absorb with inert material (e.g., sand) and
collect in a suitable, closed container. Warm, soapy water or non-flammable, safe solvent may be used to clean residual.
7. HANDLING AND STORAGE:
STORAGE TEMPERATURE (MIN./MAX):……………………………….40 F (4 C) / 90 F (32 C)
STORAGE:………………………………………………………………………….Store in tightly closed containers to prevent moisture absorption and
loss of volatiles. Store away from heat and open flame.
HANDLING PRECAUTIONS:…………………………………………………Ventilate work area. Avoid skin contact. Wash skin thoroughly after
handling. Wash contaminated clothing before reuse. Precautionary steps should be taken when curing product in large quantities. When
mixed with epoxy curing agents this product causes an exothermic, which in large masses, can produce enough heat to damage or ignite
surrounding materials and emit fumes and vapors that vary widely in composition and toxicity.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION:
EYE PROTECTION REQUIREMENTS:…………………………………..Wear safety glasses with side shields or chemical splash goggles
when exposure is more likely.
SKIN PROTECTION GUIDELINES:………………………………………..Wear liquid-proof, chemical resistant gloves (nitrile-butyl rubber,
neoprene, butyl rubber or natural rubber) and full body-covering clothing.
RESPIRATORY/VENTILATION REQUIREMENTS:
Good room ventilation is usually adequate for most operations. Use respirators when exposure to vapors from heated material or mist is
likely, unless determined to be below applicable limits. Use a NIOSH/MSHA approved respirator with organic vapor cartridge.
Note: Pro-Set, Inc. has conducted an air sampling study using this product or similarly formulated products. The results indicate that the
components sampled for (epichlorohydrin) were either so low that they were not detected at all or they were well below OSHA s
permissible exposure levels.
ADDITIONAL PROTECTIVE MEASURES:… Wash thoroughly after handling. Avoid breathing vapors from heated material. Protective
skin cream barriers can be applied to hands in addition to gloves for added protection. Generally speaking, working cleanly and following
basic precautionary measures will greatly minimize the potential for harmful exposure to this product under normal use conditions.
OCCUPATIONAL EXPOSURE LIMITS:………………………………….Not established for product as whole. Refer to OSHA s Permissible
Exposure Level (PEL) or the ACGIH Guidelines for information on specific ingredients.
9. PHYSICAL AND CHEMICAL PROPERTIES:
PHYSICAL FORM………………………………………………………………..Liquid.
COLOR……………………………………………………………………………….Clear to pale yellow.
ODOR…………………………………………………………………………………Mild.
BOILING POINT…………………………………………………………………..No data.
MELTING POINT/FREEZE POINT………………………………………….No data.
VISCOSITY………………………………………………………………………….3000 – 6000 cPs.
pH………………………………………………………………………………………No data.
SOLUBILITY IN WATER……………………………………………………….Insoluble.
SPECIFIC GRAVITY…………………………………………………………….1.18
MSDS #M1012-08a Last Revised: 03JAN08
Pro-Set Inc. Page 3 of 4 PRO-SET
M1012 Resin
BULK DENSITY…………………………………………………………………..9.85 pounds/gallon.
VAPOR PRESSURE…………………………………………………………….< 1 mmHg @ 20 mmHg.
VAPOR DENSITY...........................................................................Heavier than air.
% VOLATILE BY WEIGHT.............................................................EPA Method 24, as described in 40 CFR Part 60, was used to
determine the Volatile Matter Content of mixed epoxy resin and hardener. This method states that two-component coating systems
should be tested by mixing the individual components together at the proper ratio. Refer to the hardener's MSDS for information about
the total volatile content of the resin/hardener system.
10. REACTIVITY:
STABILITY:....................................................................................Stable.
HAZARDOUS POLYMERIZATION:...............................................Will not occur by itself, but masses of more than one pound of product
plus an aliphatic amine will cause irreversible polymerization with considerable heat buildup.
INCOMPATIBILITIES:....................................................................Strong acids and oxidizing agents.
DECOMPOSITION PRODUCTS:...................................................Carbon monoxide and carbon dioxide may be produced when the
product is heated to decomposition.
11. TOXICOLOGICAL INFORMATION:
No specific oral, inhalation or dermal toxicology data is known for this product.
Oral:................................................................No data.
Inhalation:.......................................................No data.
Dermal:...........................................................No data.
TERATOLOGY: No data.
MUTAGENICITY: No data.
CARCINOGENICITY:
NTP.........................................................................................Product not listed.
IARC.......................................................................................Product not listed.
OSHA......................................................................................Product not listed.
Many studies have been conducted to assess the potential carcinogenicity of diglycidyl ether of bisphenol-A. Although some weak
evidence of carcinogenicity has been reported in animals, when all of the data are considered, the weight of evidence does not show that
DGEBPA is carcinogenic. Indeed, the most recent review of the available data by the International Agency for Research on Cancer
(IARC) has concluded that DGEBPA is not classified as a carcinogen.
Epichlorohydrin, an impurity in this product (<5 ppm) has been reported to produce cancer in laboratory animals and to produce
mutagenic changes in bacteria and cultured human cells. It has been established by the International Agency for Research on Cancer
(IARC) as a probable human carcinogen (Group 2A) based on the following conclusions: human evidence inadequate; animal
evidence sufficient. It has been classified as an anticipated human carcinogen by the National Toxicology Program (NTP). Note: It is
unlikely that normal use of this product would result in measurable exposure concentrations to this substance.
12. ECOLOGICAL INFORMATION:
No data.
13. DISPOSAL CONSIDERATIONS:
WASTE DISPOSAL METHOD:......................................................Evaluation of this product using RCRA criteria shows that it is not a
hazardous waste, either by listing or characteristics, in its purchased form. It is the responsibility of the user to determine proper disposal
methods.
Incinerate, recycle (fuel blending) or reclaim may be preferred methods when conducted in accordance with federal, state and local
regulations.
14. TRANSPORTATION INFORMATION:
DOT SHIPPING NAME:.................................................................Not regulated by DOT.
TECHNICAL SHIPPING NAME:....................................................Not applicable.
DOT HAZARD CLASS:..................................................................Not applicable.
U.N./N.A. NUMBER:.......................................................................Not applicable.
PACKING GROUP:........................................................................Not applicable.
15. REGULATORY INFORMATION:
MSDS #M1012-08a Last Revised: 03JAN08
Pro-Set Inc. Page 4 of 4 PRO-SET
M1012 Resin
OSHA STATUS:.............................................................................Irritant; possible sensitizer.
TSCA STATUS:..............................................................................All components are listed on TSCA Inventory or otherwise comply with
TSCA requirements.
SARA TITLE III:
SECTION 313 TOXIC CHEMICALS.......................................None (deminimus).
STATE REGULATORY INFORMATION:
The following chemicals are specifically listed or otherwise regulated by individual states. For details on your regulatory requirements
you should contact the appropriate agency in your state.
COMPONENT NAME
/CAS NUMBER CONCENTRATION STATE CODE
Epichlorohydrin
106-89-8 < 5ppm
1
CA, MA, PA, RI
1.
These substances are known to the State of California to cause cancer or reproductive harm, or both.
16. OTHER INFORMATION:
REASON FOR ISSUE:...................................................................Changes in Sections 3, 5, 8, 11 & 15.
PREPARED BY:.............................................................................T. J. Atkinson
APPROVED BY:.............................................................................G. M. House
TITLE:.............................................................................................Health, Safety & Environmental Manager
APPROVAL DATE:........................................................................January 3, 2008
SUPERSEDES DATE:...................................................................January 3, 2005
MSDS NUMBER :............................................................................M1012-08a.
Note: The Hazardous Material Indexing System (HMIS), cited in the Emergency Overview of Section 3, uses the following index to assess
hazard rating: 0 = Minimal; 1 = Slight: 2 = Moderate; 3 = Serious; and 4 = Severe.
This information is furnished without warranty, expressed or implied, except that it is accurate to the best knowledge of Pro-Set Inc. The data
on this sheet is related only to the specific material designated herein. Pro-Set Inc. assumes no legal responsibility for use or reliance upon
these data.
MSDS #M1012-08a Last Revised: 03JAN08