by | Sep 27, 2025
SAFETY DATA SHEET1. IdentificationBR Polyesther Fabric BreatherProduct identifierOther means of identification8000569Product code4819 * 4822 * A3000 * AB10 * AB100 * AB120 * AB200 * AB600 * AB80 * RC3000 *SAATI61MESH * SSFAB74MESH * 158MESHSynonymsBreatherRecommended useNone known.Recommended restrictionsManufacturer/Importer/Supplier/Distributor informationManufacturerAerovac LLCCompany Name955-10 National Parkway, Schaumburg, IL 60173-5161, United States+1-847-437-0200 (International)Aerovac Mondovi S.r.LVia Vigevano 1, Mondov , CN 12084, Italy+39 (0) 174 566200Aerovac Toulouse SAS1 rue de la Sausse, Saint-Jean, 31240, France+33 (0) 5 61 378989Aerovac Keighley Ltd500 Bradford Road, Sandbeds, Keighley, BD20 5 NG, United Kingdom+44 (0) 1274 550500hse@compositesone.comE-mailCHEMTRECEmergency TelephoneUS: 1-800-424-9300Europe: +44 20 3885 0382South America: +55 11 4349 1359International: +1-703-527-38872. Hazard(s) identificationNot a hazardous product according to Globally Harmonized System (GHS)3. Composition/information on ingredientsArticleCAS number%Chemical nameCommon name and synonyms25038-59-9Pet Polymer100This material is not considered to be hazardous according to regulatory guidelines (see Section 15 of the SDS).4. First-aid measuresNot an expected route of exposure. Call a physician if symptoms develop or persist.InhalationNot an expected route of exposure. Wash off with soap and water. Get medical attention if irritationdevelops and persists.Skin contactNot an expected route of exposure. Rinse with water. Get medical attention if irritation developsand persists.Eye contactNot an expected route of exposure. Rinse mouth. Get medical attention if symptoms occur.Ingestion1 / 6Material name: BR Polyesther Fabric Breather8000569 Version #: 04 Revision date: 05-22-2024 Issue date: 05-18-2023SDS US
Direct contact with eyes may cause temporary irritation.Most importantsymptoms/effects, acute anddelayedTreat symptomatically.Indication of immediatemedical attention and specialtreatment neededGet medical attention if symptoms occur.General information5. Fire-fighting measuresWater fog. Foam. Dry chemical powder. Carbon dioxide (CO2).Suitable extinguishing mediaDo not use water jet as an extinguisher, as this will spread the fire.Unsuitable extinguishingmediaDuring fire, gases hazardous to health may be formed.Specific hazards arising fromthe chemicalWear suitable protective equipment.Special protective equipmentand precautions for firefightersMove containers from fire area if you can do so without risk.Fire fightingequipment/instructionsUse standard firefighting procedures and consider the hazards of other involved materials.Specific methodsNo unusual fire or explosion hazards noted.General fire hazards6. Accidental release measuresFor personal protection, see section 8 of the SDS.Personal precautions,protective equipment andemergency proceduresClean up in accordance with all applicable regulations.Methods and materials forcontainment and cleaning upAvoid discharge into drains, water courses or onto the ground.Environmental precautions7. Handling and storageObserve good industrial hygiene practices.Precautions for safe handlingStore in tightly closed container. Store away from incompatible materials (see Section 10 of theSDS).Conditions for safe storage,including any incompatibilities8. Exposure controls/personal protectionThis mixture has no ingredients that have PEL, TLV, or other recommended exposure limit.Occupational exposure limitsNo biological exposure limits noted for the ingredient(s).Biological limit valuesGood general ventilation should be used. Ventilation rates should be matched to conditions. Ifapplicable, use process enclosures, local exhaust ventilation, or other engineering controls tomaintain airborne levels below recommended exposure limits. If exposure limits have not beenestablished, maintain airborne levels to an acceptable level.Appropriate engineeringcontrolsIndividual protection measures, such as personal protective equipmentWear safety glasses with side shields (or goggles).Eye/face protectionSkin protectionWear appropriate chemical resistant gloves.Hand protectionWear suitable protective clothing.OtherIn case of insufficient ventilation, wear suitable respiratory equipment.Respiratory protectionWear appropriate thermal protective clothing, when necessary.Thermal hazardsAlways observe good personal hygiene measures, such as washing after handling the materialand before eating, drinking, and/or smoking. Routinely wash work clothing and protectiveequipment to remove contaminants.General hygieneconsiderations9. Physical and chemical properties AppearanceSolid.Physical stateSolid.FormNot available.ColorNot available.OdorOdor thresholdNot available.2 / 6Material name: BR Polyesther Fabric Breather8000569 Version #: 04 Revision date: 05-22-2024 Issue date: 05-18-2023SDS US
pHNot available.Melting point/freezing point509 F (265 C) estimatedInitial boiling point and boilingrangeNot available.Flash pointNot available.Evaporation rateNot available.Not available.Flammability (solid, gas)Upper/lower flammability or explosive limitsExplosive limit – lower (%)Not available.Explosive limit – upper (%)Not available.Vapor pressureNot available.Vapor densityNot available.Relative densityNot available.Solubility(ies)Solubility (water)Not available.Partition coefficient(n-octanol/water)Not available.Auto-ignition temperatureNot available.Decomposition temperatureNot available.ViscosityNot available.Other informationDensity1.38 g/cm3 estimatedNot explosive.Explosive propertiesNot oxidizing.Oxidizing propertiesPercent volatile0 % w/w estimatedSpecific gravity1.38 estimatedVOC0 % estimated10. Stability and reactivityThe product is stable and non-reactive under normal conditions of use, storage and transport.ReactivityMaterial is stable under normal conditions.Chemical stabilityNo dangerous reaction known under conditions of normal use.Possibility of hazardousreactionsContact with incompatible materials.Conditions to avoidStrong oxidizing agents.Incompatible materialsNo hazardous decomposition products are known.Hazardous decompositionproducts11. Toxicological informationInformation on likely routes of exposureInhalationNo adverse effects due to inhalation are expected.Skin contactNo adverse effects due to skin contact are expected.Eye contactDirect contact with eyes may cause temporary irritation.IngestionExpected to be a low ingestion hazard.Symptoms related to thephysical, chemical andtoxicological characteristicsDirect contact with eyes may cause temporary irritation.Information on toxicological effectsAcute toxicityNot known.Prolonged skin contact may cause temporary irritation.Skin corrosion/irritationDirect contact with eyes may cause temporary irritation.Serious eye damage/eyeirritationRespiratory or skin sensitizationRespiratory sensitizationNot a respiratory sensitizer.3 / 6Material name: BR Polyesther Fabric Breather8000569 Version #: 04 Revision date: 05-22-2024 Issue date: 05-18-2023SDS US
This product is not expected to cause skin sensitization.Skin sensitizationNo data available to indicate product or any components present at greater than 0.1% aremutagenic or genotoxic.Germ cell mutagenicityCarcinogenicityNot classifiable as to carcinogenicity to humans.IARC Monographs. Overall Evaluation of CarcinogenicityNot listed.OSHA Specifically Regulated Substances (29 CFR 1910.1001-1053)Not listed.US. National Toxicology Program (NTP) Report on CarcinogensNot listed.This product is not expected to cause reproductive or developmental effects.Reproductive toxicitySpecific target organ toxicity -single exposureNot classified.Specific target organ toxicity -repeated exposureNot classified.Aspiration hazardNot an aspiration hazard.12. Ecological informationThe product is not classified as environmentally hazardous. However, this does not exclude thepossibility that large or frequent spills can have a harmful or damaging effect on the environment.EcotoxicityNo data is available on the degradability of any ingredients in the mixture. Persistence and degradabilityNo data available.Bioaccumulative potentialNo data available.Mobility in soilOther adverse effectsNo other adverse environmental effects (e.g. ozone depletion, photochemical ozone creationpotential, endocrine disruption, global warming potential) are expected from this component.13. Disposal considerationsNot available.Disposal instructionsDispose in accordance with all applicable regulations.Local disposal regulationsNot available.Waste from residues / unusedproductsNot available.Contaminated packaging14. Transport informationDOTNot regulated as dangerous goods.IATANot regulated as dangerous goods.IMDGNot regulated as dangerous goods.Not applicable.Transport in bulk according toAnnex II of MARPOL 73/78 andthe IBC Code15. Regulatory informationThis product is not known to be a “Hazardous Chemical” as defined by the OSHA HazardCommunication Standard, 29 CFR 1910.1200.US federal regulationsToxic Substances Control Act (TSCA)All components of the mixture on the TSCA 8(b) inventory are designated active .TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)Not regulated.CERCLA Hazardous Substance List (40 CFR 302.4)Not listed.SARA 304 Emergency release notificationNot regulated.OSHA Specifically Regulated Substances (29 CFR 1910.1001-1053)Not listed.4 / 6Material name: BR Polyesther Fabric Breather8000569 Version #: 04 Revision date: 05-22-2024 Issue date: 05-18-2023SDS US
SARA 302 Extremely hazardous substanceSuperfund Amendments and Reauthorization Act of 1986 (SARA)Not listed.No (Exempt)SARA 311/312 HazardouschemicalSARA 313 (TRI reporting)Not regulated.Other federal regulationsClean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) ListNot regulated.Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)Not regulated.Not regulated.Safe Drinking Water Act(SDWA)US state regulationsCalifornia Proposition 65California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This materialis not known to contain any chemicals currently listed as carcinogens or reproductive toxins. Formore information go to www.P65Warnings.ca.gov.International InventoriesCountry(s) or regionInventory nameOn inventory (yes/no)*YesAustraliaAustralian Inventory of Industrial Chemicals (AICIS)YesCanadaDomestic Substances List (DSL)NoCanadaNon-Domestic Substances List (NDSL)YesChinaInventory of Existing Chemical Substances in China (IECSC)NoEuropeEuropean Inventory of Existing Commercial ChemicalSubstances (EINECS)NoEuropeEuropean List of Notified Chemical Substances (ELINCS)YesJapanInventory of Existing and New Chemical Substances (ENCS)YesKoreaExisting Chemicals List (ECL)YesNew ZealandNew Zealand InventoryYesPhilippinesPhilippine Inventory of Chemicals and Chemical Substances(PICCS)YesTaiwanTaiwan Chemical Substance Inventory (TCSI)YesUnited States & Puerto RicoToxic Substances Control Act (TSCA) Inventory*A “Yes” indicates that all components of this product comply with the inventory requirements administered by the governing country(s)A “No” indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governingcountry(s).16. Other information, including date of preparation or last revision05-18-2023Issue date05-22-2024Revision dateVersion #04Health: 0Flammability: 0Instability: 0NFPA ratingsNFPA ratings 0005 / 6Material name: BR Polyesther Fabric Breather8000569 Version #: 04 Revision date: 05-22-2024 Issue date: 05-18-2023SDS US
Aerovac LLC cannot anticipate all conditions under which this information and its product, or theproducts of other manufacturers in combination with its product, may be used. It is the user sresponsibility to ensure safe conditions for handling, storage and disposal of the product, and toassume liability for loss, injury, damage or expense due to improper use. The information in thesheet was written based on the best knowledge and experience currently available. Informationcontained herein is believed to be true and accurate, but all statements or suggestions are madewithout warranty, expressed or implied, regarding accuracy of the information, the hazardsconnected with the use of the material or the results to be obtained from the use thereof.Compliance with all applicable federal, state and local laws and local regulations remains theresponsibility of the user. This safety data sheet cannot cover all possible situations which the usermay experience during processing. Each aspect of your operation should be examined todetermine if, or where, additional precautions may be necessary. All health and safety informationcontained in this safety data sheet should be provided to your employees or customers. It is yourresponsibility to develop appropriate work practice guidelines and employee instructional programsfor your operation.DisclaimerProduct and Company Identification: Product and Company IdentificationRevision information6 / 6Material name: BR Polyesther Fabric Breather8000569 Version #: 04 Revision date: 05-22-2024 Issue date: 05-18-2023SDS US
by | Sep 27, 2025
SDS: 0058936
Date Prepared: 02/05/2017
SAFETY DATA SHEET
1. IDENTIFICATION
Product Name: VAC-PAK HS8171
Product Description: Nylon film
Synonyms: None
Chemical Family: Nylon film
Molecular Formula: Not applicable
Molecular Weight: Not applicable
Intended/Recommended Use: Film
CYTEC INDUSTRIES INC., 504 CARNEGIE CENTER, PRINCETO N, NEW JERSEY 08540, USA
For Product and all Non-Emergency Information call 1-800/652-6013. Outside the USA and Canada call 1-973/357-
3193.
EMERGENCY PHONE (24 hours/day) – For emergency only involving spill, leak, fire, exposure or accident call:
Asia Pacific:
Australia – +61 2 8014 4558 (Carechem24)
China (PRC) – +86 0532 83889090 (NRCC) +86 512 8090 3042 (Carechem24)
New Guinea – +61 2 8014 4558 (Carechem24)
New Zealand – +64 9 929 1483 (Carechem24)
India, Japan, Korea, Malaysia, Thailand – +65 3158 1074 (Carechem24 Singapore)
India (Hindi Speaking Only) – +65 3158 1198 or 000800 100 7479 (Carechem24 Singapore)
Canada: 800 424 9300 (Within US,Canada) +1 (703) 527-3887 (International) (CHEMTREC)
Europe/Africa/Middle East (Carechem24 UK):
Europe, Middle East, Africa, Israel – +44 1235 239 670
(Arabic speaking countries) – +44 1235 239 671
Latin America:
Brazil – +55 11 3197 5891 (Carechem24)
Chile – +56 2 2582 9336 (Carechem24)
All Others – +44 1235 239 670 (Carechem24 UK)
USA: 800 424 9300 (Within US,Canada) +1 (703) 527-3887 (International) (CHEMTREC)
2. HAZARDS IDENTIFICATION
GHS Classification
Not Classified
LABEL ELEMENTS
Not Applicable
Hazard Statements Not Applicable
Precautionary Statements
Not Applicable
Hazards Not Otherwise Classified (HNOC), Other Hazards
By excessive exposure to dust, eye and respiratory tract irritation is possible.
3. COMPOSITION/INFORMATION ON INGREDIENTS
HAZARDOUS INGREDIENTS
Component / CAS No. % GHS Classification Carcinogen
Caprolactam
105-60-2
0-1 Acute Tox. 4 (H302)
Acute Tox. 4 (H332)
STOT SE 3 (H335)
Skin Irrit. 2 (H315)
Eye Irrit. 2A (H319)
–
The specific chemical identity and/or exact percentage of composition for one or more ingredients has been withheld as a
trade secret.
Additional GHS classification or other information may be included in this section but has not been adopted by OSHA.
See Section 16 for full text of H phrases.
4. FIRST AID MEASURES
DESCRIPTION OF FIRST AID MEASURES
Eye Contact:
Not an expected route of exposure.
Skin Contact:
Wash immediately with plenty of water and soap.
Ingestion:
Not an expected route of exposure.
Inhalation:
Not an expected route of exposure.
MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED
None known
INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND SPECIAL TREATMENT NEEDS
Not applicable
5. FIRE-FIGHTING MEASURES
Suitable Extinguishing Media:
Use water spray or fog, carbon dioxide or dry chemical.
Extinguishing Media to Avoid:
full water jet
Protective Equipment:
Firefighters, and others exposed, wear self-contained breathing apparatus. Wear full firefighting protective clothing. See
MSDS Section 8 (Exposure Controls/Personal Protection).
Page 2 of 8VAC-PAK HS8171 SDS: 0058936 Date Prepared: 02/05/2017
Special Hazards:
None known
6. ACCIDENTAL RELEASE MEASURES
Personal precautions:
Where exposure level is not known, wear approved, positive pressure, self-contained respirator. Where exposure level is
known, wear approved respirator suitable for level of exposure. Refer to Section 8 (Exposure Controls/Personal
Protection) for appropriate personal protective equipment.
Methods For Cleaning Up:
Sweep up into containers for disposal. Flush spill area with water.
References to other sections:
See Sections 8 and 13 for additional information.
7. HANDLING AND STORAGE
HANDLING
Precautions: None
Special Handling Statements: Heating or curing of unused rolls or sheets of product prior to disposal is not
recommended. Heating a large mass of product can lead to a rapid decomposition reaction, generating heat,
smoke and possibly fire.
STORAGE
Store in accordance with local, state, and federal regulations.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Engineering Measures:
Where this material is not used in a closed system, good enclosure and local exhaust ventilation should be provided to
control exposure when spraying or curing at elevated temperatures.
Respiratory Protection:
Where exposures are below the established exposure limit, no respiratory protection is required. Where exposures
exceed the established exposure limit, use respiratory protection recommended for the material and level of exposure. A
full facepiece respirator also provides eye and face protection. Cutting, grinding or sanding of parts fabricated after curing
may create respirable dust particles. Respiratory protection appropriate for this dust may be required. Refer to
components listed above for potential hazardous components in the dust.
Eye Protection:
Wear eye/face protection such as chemical splash proof goggles or face shield. Eyewash equipment and safety shower
should be provided in areas of potential exposure.
Skin Protection:
Avoid skin contact. Wear impermeable gloves and suitable protective clothing. Barrier creams may be used in conjunction
with the gloves to provide additional skin protection.
Hand Protection:
Wear impermeable gloves. Replace gloves immediately when torn or any change in appearance (dimension, colour,
flexibility etc) is noticed. Barrier creams may help to protect the exposed areas of the skin, they should however not be
applied once exposure has occurred. Consider the porosity and elasticity data of the glove manufacturer and the specific
conditions in the work place.
Page 3 of 8VAC-PAK HS8171 SDS: 0058936 Date Prepared: 02/05/2017
Additional Advice:
Food, beverages, and tobacco products should not be carried, stored, or consumed where this material is in use. Before
eating, drinking, or smoking, wash face and hands thoroughly with soap and water.
Exposure Limit(s)
The below constituents are the only constituents of the product which have a PEL, TLV or other recommended exposure
limit. At this time, the other constituents have no known exposure limits.
9. PHYSICAL AND CHEMICAL PROPERTIES
Color: green
Appearance: film
Odor: none
Boiling Point: Not applicable
Melting Point: 215 – 250 C 420 – 485 F
Vapor Pressure: Not applicable
Specific Gravity/Density: Not available
Vapor Density: Not available
Percent Volatile (% by wt.): Not available
pH: Not applicable
Saturation In Air (% By Vol.):Not applicable
Evaporation Rate: Not applicable
Solubility In Water: negligible
Volatile Organic Content:
Flash Point: Not available
Flammability (solid, gas): Not available
Flammable Limits (% By Vol): Not available
Autoignition (Self) Temperature:Not available
Decomposition Temperature: Not available
Partition coefficient (n-
octanol/water):
Not available
Odor Threshold: Not available
Viscosity (Kinematic): Not available
DUST HAZARD INFORMATION
Particle Size (microns): Not applicable
Kst (bar-m/sec): Not applicable
Maximum Explosion Pressure (Pmax): Not applicable
Dust Class: Not applicable
Minimum Ignition Energy (MIE) (mJ): Not applicable
Minimum Ignition Temperature (MIT) ( C): Not applicable
Minimum Explosive Concentration (MEC) (g/m
3
): Not applicable
Limiting Oxygen Concentration (LOC) (%): Not applicable
10. STABILITY AND REACTIVITY
Reactivity: No information available
Stability: Stable
Not established
SDS: 0058936
ACGIH (TLV): 5 mg/m
3
inhalable fraction and vapor (TWA)
Date Prepared: 02/05/2017
Other Value: Not established
105-60-2 Caprolactam
Page 4 of 8VAC-PAK HS8171
OSHA (PEL):
Polymerization: Will not occur
Conditions To Avoid: Avoid contact with sunlight or ultraviolet light. Avoid exposure to temperatures
exceeding recommended processing conditions.
Materials To Avoid: Strong oxidizing agents.
Hazardous Decomposition
Products:
ammonia
Caprolactam
Carbon monoxide and carbon dioxide
hydrogen cyanide (HCN)
11. TOXICOLOGICAL INFORMATION
PRODUCT TOXICITY INFORMATION
Likely Routes of Exposure: Skin.
ACUTE TOXICITY DATA
LOCAL EFFECTS ON SKIN AND EYE
ALLERGIC SENSITIZATION
GENOTOXICITY
Assays for Gene Mutations
OTHER INFORMATION
The product toxicity information above has been estimated.
HAZARDOUS INGREDIENT TOXICITY DATA
12. ECOLOGICAL INFORMATION
TOXICITY, PERSISTENCE AND DEGRADABI LITY, BIOACCUMULATIVE POTENTIAL, MOBILITY IN SOIL, OTHER
ADVERSE EFFECTS
Not an expected route of
exposure
dermal
Sensitization
rabbit
skin No data
Acute LD50
Sensitization
Page 5 of 8
respiratory
.No data
Not an expected route of
exposure
VAC-PAK HS8171
inhalation
oral
Ames Salmonella Assay
rat
No data
Acute LC50 4 hr .Not an expected route of
exposure
SDS: 0058936
rat
Acute Irritation
Acute overexposure to caprolactam vapor may cause respiratory irritation. Dermal contact with caprolactam dust may
cause skin irritation. The oral (rat) and dermal (rabbit) LD50 values are 1.4-2.1 g/kg and 1.4 g/kg, respectively. The
acute inhalation (rat) 4-hr LC50 for a 50% (w/v) in water aerosol exposure was 8.16 mg/L (based on percent active LC50
is ~ 4mg/L). Exposure to caprolactam and ethyl alcohol has resulted in reddening of the skin.
Acute LD50
skin No data .Not an expected route of
exposure
Acute Irritation eye
Date Prepared: 02/05/2017
Environmental exposure from substances of this preparation are limited due to the physical form of the product.
This material is not classified as dangerous for the environment.
RESULTS OF PBT AND vPvB ASSESSMENT
Not determined
HAZARDOUS INGREDIENT TOXICITY DATA
Component / CAS No. Toxicity to Algae Toxicity to Fish Toxicity to Water Flea
Caprolactam
105-60-2
EC50 4320 – 4800 mg/L –
Pseudokirchneriella subcapitata
(72h)
EC50 = 130 mg/L –
Desmodesmus subspicatus (72h)
EC50 = 160 mg/L –
Desmodesmus subspicatus (96h)
LC50 = 1400 mg/L – Pimephales
promelas (96h) static
LC50 = 930 mg/L – Lepomis
macrochirus (96h) static
EC50 828 – 2920 mg/L –
Daphnia magna (48h)
EC50 > 500 mg/L – Daphnia
magna Straus (48h)
13. DISPOSAL CONSIDERATIONS
The information on RCRA waste classification and disposal methodology provided below applies only to the product, as
supplied. If the material has been altered or contaminated, or it has exceeded its recommended shelf life, the guidance
may be inapplicable. Hazardous waste classification under federal regulations (40 CFR Part 261 et seq) is dependent
upon whether a material is a RCRA “listed hazardous waste” or has any of the four RCRA “hazardous waste
characteristics.” Refer to 40 CFR Part 261.33 to determine if a given material to be disposed of is a RCRA “listed
hazardous waste”; information contained in Section 15 of this MSDS is not intended to indicate if the product is a “listed
hazardous waste.” RCRA Hazardous Waste Characteristics: There are four characteristics defined in 40 CFR Section
261.21-61.24: Ignitability, Corrosivity, Reactivity, and Toxicity. To determine Ignitability, see Section 9 of this MSDS
(flash point). For Corrosivity, see Sections 9 and 14 (pH and DOT corrosivity). For Reactivity, see Section 10
(incompatible materials). For Toxicity, see Section 3 (composition). Federal regulations are subject to change. State and
local requirements, which may differ from or be more stringent than the federal regulations, may also apply to the
classification of the material if it is to be disposed. The Company encourages the recycle, recovery and reuse of
materials, where permitted, as an alternate to disposal as a waste. The Company recommends that organic materials
classified as RCRA hazardous wastes be disposed of by thermal treatment or incineration at EPA approved facilities.
The Company has provided the foregoing for information only; the person generating the waste is responsible for
determining the waste classification and disposal method.
14. TRANSPORT INFORMATION
This section provides basic shipping classification information. Refer to appropriate transportation regulations for specific
requirements.
VAC-PAK HS8171 SDS: 0058936 Date Prepared: 02/05/2017 Page 6 of 8
US DOT
Dangerous Goods? Not applicable/Not regulated
TRANSPORT CANADA
Dangerous Goods? Not applicable/Not regulated
ICAO / IATA
Dangerous Goods? Not applicable/Not regulated
IMO
Dangerous Goods? Not applicable/Not regulated
_____________________________________________________________________________
15. REGULATORY INFORMATION
Inventory Information
United States (USA): All components of this product are included on the TSCA Chemical Inventory or are not
required to be listed on the TSCA Chemical Inventory.
Canada: All components of this product are included on the Domestic Substances List (DSL) or are not required to
be listed on the DSL.
Australia: All components of this product are included in the Australian Inventory of Chemical Substances (AICS)
or are not required to be listed on AICS.
China: All components of this product are included on the Chinese inventory or are not required to be listed on the
Chinese inventory.
Japan: All components of this product are included on the Japanese (ENCS) inventory or are not required to be
listed on the Japanese inventory.
Korea: All components of this product are included on the Korean (ECL) inventory or are not required to be listed
on the Korean inventory.
Philippines: All components of this product are included on the Philippine (PICCS) inventory or are not required to
be listed on the Philippine inventory.
OTHER ENVIRONMENTAL INFORMATION
The following components of this product may be subject to reporting requirements pursuant to Section 313 of CERCLA
(40 CFR 372), Section 12(b) of TSCA, or may be subject to release reporting requirements (40 CFR 307, 40 CFR 311,
etc.) See Section 13 for information on waste classification and waste disposal of this product.
This product does not contain any components regulated under these sections of the EPA
PRODUCT HAZARD CLASSIFICATION UNDER SECTION 311 OF SARA
Not applicable
_____________________________________________________________________________
16. OTHER INFORMATION
NFPA Hazard Rating (National Fire Protection Association)
Health: 0 – Materials that under emergency conditions, would offer no hazard beyond that of ordinary combustible
materials.
Page 7 of 8VAC-PAK HS8171 SDS: 0058936 Date Prepared: 02/05/2017
Fire: 1 – Materials that must be preheated before ignition can occur.
Instability: 0 – Materials that in themselves are normally stable, even under fire exposure conditions.
Reasons For Issue: Revised Section 1
Date Prepared: 02/05/2017
Date of last significant revision:02/01/2017
Component Hazard Phrases
Prepared By: Legal & Compliance Services; E-mail: custinfo@solvay.com
This information is given without any warranty or representation. We do not assume any legal responsibility for same, nor do we give permission,
inducement, or recommendation to practice any patented invention without a license. It is offered solely for your consideration, investigation, and
verification. Before using any product, read its label.
Date Prepared: 02/05/2017
Caprolactam
Page 8 of 8VAC-PAK HS8171
H302 – Harmful if swallowed.
H315 – Causes skin irritation.
H319 – Causes serious eye irritation.
H332 – Harmful if inhaled.
H335 – May cause respiratory irritation.
SDS: 0058936
by | Sep 27, 2025
SDS: 0059106
Date Prepared: 02/09/2018
SAFETY DATA SHEET
1. IDENTIFICATION
Product Name:
Nylon Film/Fabric/Felt
Product Description: Nylon film
Synonyms: None
Chemical Family: Nylon film
Molecular Formula: Not applicable
Molecular Weight: Not applicable
Intended/Recommended Use: Tooling
Other Product Names: HS8171, HS8171 6/66, 58179, 51789SRB, SV2000, VINYL SPIRAL WRAP,
A100PS, 51789.I.O, 51789.NAT, B100, B100BLEU, HS6262, VAC PAK HS6262,
D300, AB40, AB40N, A100FLOGREEN, MQ251, 41661, 52006, 52008 , B-100,
B4444, VAC PAK HS800.
This SDS covers multiple products. For industrial exposure and emergency
response purposes, all listed products above have similar physical, chemical and
hazard properties.
CYTEC INDUSTRIES INC., 504 CARNEGIE CENTER, PRINCETON, NEW JERSEY 08540, USA
For Product and all Non-Emergency Information call 1-800/652-6013. Outside the USA and Canada call 1-973/357-
3193.
EMERGENCY PHONE (24 hours/day) – For emergency only involving spill, leak, fire, exposure or accident call:
Asia Pacific:
Australia – +61 2 8014 4558 (Carechem24)
China (PRC) – +86 0532 83889090 (NRCC) +86 512 8090 3042 (Carechem24)
New Guinea – +61 2 8014 4558 (Carechem24)
New Zealand – +64 9 929 1483 (Carechem24)
India, Japan, Korea, Malaysia, Thailand – +65 3158 1074 (Carechem24 Singapore)
India (Hindi Speaking Only) – +65 3158 1198 or 000800 100 7479 (Carechem24 Singapore)
Canada: 800 424 9300 (Within US,Canada) +1 (703) 527-3887 (International) (CHEMTREC)
Europe/Africa/Middle East (Carechem24 UK):
Europe, Middle East, Africa, Israel – +44 1235 239 670
(Arabic speaking countries) – +44 1235 239 671
Latin America:
Brazil – +55 11 3197 5891 (Carechem24)
Chile – +56 2 2582 9336 (Carechem24)
All Others – +44 1235 239 670 (Carechem24 UK)
USA: 800 424 9300 (Within US,Canada) +1 (703) 527-3887 (International) (CHEMTREC)
2. HAZARDS IDENTIFICATION
GHS Classification
Not Classified
LABEL ELEMENTS
Not Applicable
Hazard Statements
Not Applicable
Precautionary Statements
Not Applicable
Hazards Not Otherwise Classified (HNOC), Other Hazards
By excessive exposure to dust, eye and respiratory tract irritation is possible.
3. COMPOSITION/INFORMATION ON INGREDIENTS
Substance, Mixture or Article?Article
HAZARDOUS INGREDIENTS
Component / CAS No. % GHS Classification Carcinogen
Caprolactam
105-60-2
1 – 5 Acute Tox. 4 (H302)
Acute Tox. 4 (H332)
STOT SE 3 (H335)
Skin Irrit. 2 (H315)
Eye Irrit. 2A (H319)
–
The specific chemical identity and/or exact percentage of composition for one or more ingredients has been withheld as a
trade secret.
Additional GHS classification or other information may be included in this section but has not been adopted by OSHA.
See Section 16 for full text of H phrases.
4. FIRST AID MEASURES
DESCRIPTION OF FIRST AID MEASURES
Eye Contact:
Not an expected route of exposure.
Skin Contact:
Wash immediately with plenty of water and soap.
Ingestion:
Not an expected route of exposure.
Inhalation:
Remove to fresh air. If breathing is difficult, give oxygen. Obtain medical advice if there are persistent symptoms.
MOST IMPORTANT SYMPTOMS AND EFFECTS, BOTH ACUTE AND DELAYED
None known
INDICATION OF ANY IMMEDIATE MEDICAL ATTENTION AND S PECIAL TREATMENT NEEDS
Not applicable
Page 2 of 8Nylon Film/Fabric/Felt SDS: 0059106 Date Prepared: 02/09/2018
5. FIRE-FIGHTING MEASURES
Suitable Extinguishing Media:
Use water spray or fog, carbon dioxide or dry chemical.
Extinguishing Media to Avoid:
full water jet.
Protective Equipment:
Firefighters, and others exposed, wear self-contained breathing apparatus.
Special Hazards:
None known
6. ACCIDENTAL RELEASE MEASURES
Personal precautions:
Refer to Section 8 (Exposure Controls/Personal Protection) for appropriate personal protective equipment.
Methods For Cleaning Up:
Sweep up into containers for disposal. Flush spill area with water.
References to other sections:
See Sections 8 and 13 for additional information.
7. HANDLING AND STORAGE
HANDLING
Precautions: None
Special Handling Statements: Heating or curing of unused rolls or sheets of product prior to disposal is not
recommended. Heating a large mass of product can lead to a rapid decomposition reaction, generating heat,
smoke and possibly fire. Provide good ventilation of working area (local exhaust ventilation if necessary).
STORAGE
Store in accordance with local, state, and federal regulations.
Storage Temperature: Room temperature
Reason: Quality.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Engineering Measures:
Engineering controls are not usually necessary if good hygiene practices are followed.
Respiratory Protection:
Where exposures are below the established exposure limit, no respiratory protection is required. Where exposures
exceed the established exposure limit, use respiratory protection recommended for the material and level of exposure.
Eye Protection:
Wear eye/face protection.
Skin Protection:
Avoid skin contact. Wear impermeable gloves.
Page 3 of 8Nylon Film/Fabric/Felt SDS: 0059106 Date Prepared: 02/09/2018
Hand Protection:
Wear impermeable gloves. Replace gloves immediately when torn or any change in appearance (dimension, colour,
flexibility etc) is noticed.
Additional Advice:
Before eating, drinking, or smoking, wash face and hands thoroughly with soap and water.
Exposure Limit(s)
The below constituents are the only constituents of the product which have a PEL, TLV or other recommended exposure
limit. At this time, the other constituents have no known exposure limits.
9. PHYSICAL AND CHEMICAL PROPERTIES
Color: color varies
Appearance: film, fabric or felt
Odor: none
Boiling Point: Not applicable
Melting Point: 215 – 265 C 420 – 509 F
Vapor Pressure: Not applicable
Specific Gravity/Density: Not available
Vapor Density: Not available
Percent Volatile (% by wt.): Not available
pH: Not applicable
Saturation In Air (% By Vol.):Not applicable
Evaporation Rate: Not applicable
Solubility In Water: negligible
Volatile Organic Content: Not available
Flash Point: >400 C 752 F
Flammability (solid, gas): Not available
Flammable Limits (% By Vol): Not available
Autoignition (Self) Temperature:>450 C 842 F
Decomposition Temperature: >350 C 662 F
Partition coefficient (n-
octanol/water):
Not available
Odor Threshold: Not available
Viscosity (Kinematic): Not available
DUST HAZARD INFORMATION
Particle Size (microns): Not available
Kst (bar-m/sec): Not available
Maximum Explosion Pressure (Pmax): Not available
Dust Class: Not available
Minimum Ignition Energy (MIE) (mJ): Not available
Minimum Ignition Temperature (MIT) ( C): Not available
Minimum Explosive Concentration (MEC) (g/m
3
): Not available
Limiting Oxygen Concentration (LOC) (%): Not available
10. STABILITY AND REACTIVITY
105-60-2 Caprolactam
SDS: 0059106
OSHA (PEL): Not established
Date Prepared: 02/09/2018
ACGIH (TLV): 5 mg/m
3
inhalable fraction and vapor (TWA)
Page 4 of 8
Other Value: Not established
Nylon Film/Fabric/Felt
10. STABILITY AND REACTIVITY
Reactivity: No information available
Stability: Stable
Polymerization: Will not occur
Conditions To Avoid: Avoid contact with sunlight or ultraviolet light. Avoid exposure to temperatures
exceeding recommended processing conditions.
Materials To Avoid: Strong acids or bases
Strong oxidizing agents.
Hazardous Decomposition
Products:
aldehydes
hydrogen cyanide (HCN)
nitrogen oxides
Amine
ketones
ammonia
Caprolactam
Carbon monoxide and carbon dioxide
Nitrites
11. TOXICOLOGICAL INFORMATION
PRODUCT TOXICITY INFORMATION
Likely Routes of Exposure: Skin.
ACUTE TOXICITY DATA
LOCAL EFFECTS ON SKIN AND EYE
ALLERGIC SENSITIZATION
GENOTOXICITY
Assays for Gene Mutations
OTHER INFORMATION
The product toxicity information above has been estimated.
HAZARDOUS INGREDIENT TOXICITY DATA
skin No data
.Not an expected route of
exposure
Acute Irritation eye
Date Prepared: 02/09/2018
Not an expected route of
exposure
dermal
Sensitization
rabbit
skin Not sensitizing
Acute LD50
Sensitization
Page 5 of 8
respiratory
.>2000 mg/kg
Not an expected route of
exposure
Nylon Film/Fabric/Felt
inhalation
oral
Ames Salmonella Assay
rat
No data
Acute LC50
4 hr
.Not an expected route of
exposure
SDS: 0059106
rat
Acute Irritation
Acute LD50
12. ECOLOGICAL INFORMATION
TOXICITY, PERSISTENCE AND DEGRADABILITY, BIOACCUMUL ATIVE POTENTIAL, MOBILITY IN SOIL, OTHER
ADVERSE EFFECTS
This material is not classified as dangerous for the environment.
Environmental exposure from substances of this preparation are limited due to the physical form of the product.
RESULTS OF PBT AND vPvB ASSESSMENT
Not determined
HAZARDOUS INGREDIENT TOXICITY DATA
Component / CAS No. Toxicity to Algae Toxicity to Fish Toxicity to Water Flea
Caprolactam
105-60-2
EC50 4320 – 4800 mg/L –
Pseudokirchneriella subcapitata
(72h)
EC50 = 130 mg/L –
Desmodesmus subspicatus (72h)
EC50 = 160 mg/L –
Desmodesmus subspicatus (96h)
LC50 = 1400 mg/L – Pimephales
promelas (96h) static
LC50 = 930 mg/L – Lepomis
macrochirus (96h) static
EC50 828 – 2920 mg/L –
Daphnia magna (48h)
EC50 > 500 mg/L – Daphnia
magna Straus (48h)
13. DISPOSAL CONSIDERATIONS
Page 6 of 8Nylon Film/Fabric/Felt SDS: 0059106 Date Prepared: 02/09/2018
Acute overexposure to caprolactam vapor may cause respiratory irritation. Dermal contact with caprolactam dust may
cause skin irritation. The oral (rat) and dermal (rabbit) LD50 values are 1.4-2.1 g/kg and 1.4 g/kg, respectively. The
acute inhalation (rat) 4-hr LC50 for a 50% (w/v) in water aerosol exposure was 8.16 mg/L (based on percent active LC50
is ~ 4mg/L). Exposure to caprolactam and ethyl alcohol has resulted in reddening of the skin.
13. DISPOSAL CONSIDERATIONS
The information on RCRA waste classification and disposal methodology provided below applies only to the product, as
supplied. If the material has been altered or contaminated, or it has exceeded its recommended shelf life, the guidance
may be inapplicable. Hazardous waste classification under federal regulations (40 CFR Part 261 et seq) is dependent
upon whether a material is a RCRA “listed hazardous waste” or has any of the four RCRA “hazardous waste
characteristics.” Refer to 40 CFR Part 261.33 to determine if a given material to be disposed of is a RCRA “listed
hazardous waste”; information contained in Section 15 of this MSDS is not intended to indicate if the product is a “listed
hazardous waste.” RCRA Hazardous Waste Characteristics: There are four characteristics defined in 40 CFR Section
261.21-61.24: Ignitability, Corrosivity, Reactivity, and Toxicity. To determine Ignitability, see Section 9 of this MSDS
(flash point). For Corrosivity, see Sections 9 and 14 (pH and DOT corrosivity). For Reactivity, see Section 10
(incompatible materials). For Toxicity, see Section 3 (composition). Federal regulations are subject to change. State and
local requirements, which may differ from or be more stringent than the federal regulations, may also apply to the
classification of the material if it is to be disposed. The Company encourages the recycle, recovery and reuse of
materials, where permitted, as an alternate to disposal as a waste. The Company recommends that organic materials
classified as RCRA hazardous wastes be disposed of by thermal treatment or incineration at EPA approved facilities.
The Company has provided the foregoing for information only; the person generating the waste is responsible for
determining the waste classification and disposal method.
14. TRANSPORT INFORMATION
This section provides basic shipping classification information. Refer to appropriate transportation regulations for specific
requirements.
US DOT
Dangerous Goods? Not applicable/Not regulated
TRANSPORT CANADA
Dangerous Goods? Not applicable/Not regulated
ICAO / IATA
Dangerous Goods? Not applicable/Not regulated
IMO
Dangerous Goods? Not applicable/Not regulated
___________________________________________________ __________________________
15. REGULATORY INFORMATION
Inventory Information
United States (USA): All components of this product are included on the TSCA Chemical Inventory or are not
required to be listed on the TSCA Chemical Inventory.
Canada: All components of this product are included on the Domestic Substances List (DSL) or are not required to
be listed on the DSL.
European Economic Area (including EU): This product is an article that does not intentionally release substances
under normal conditions of use and is therefore exempt from the registration requirements under the REACH
Regulation (EC) No. 1907/2006.
Australia: All components of this product are included in the Australian Inventory of Chemical Substances (AICS)
or are not required to be listed on AICS.
China: All components of this product are included on the Chinese inventory or are not required to be listed on the
Chinese inventory.
Date Prepared: 02/09/2018 Page 7 of 8Nylon Film/Fabric/Felt SDS: 0059106
Japan: All components of this product are included on the Japanese (ENCS) inventory or are not required to be
listed on the Japanese inventory.
Korea: All components of this product are included on the Korean (ECL) inventory or are not required to be listed
on the Korean inventory.
Philippines: All components of this product are included on the Philippine (PICCS) inventory or are not required to
be listed on the Philippine inventory.
Taiwan: All components of this product are included on the Taiwan Chemical Substance Inventory (TCSI) or are
not required to be listed on the Taiwan inventory.
OTHER ENVIRONMENTAL INFORMATION
The following components of this product may be subject to reporting requirements pursuant to Section 313 of CERCLA
(40 CFR 372), Section 12(b) of TSCA, or may be subject to release reporting requirements (40 CFR 307, 40 CFR 311,
etc.) See Section 13 for information on waste classification and waste disposal of this product.
This product does not contain any components regulated under these sections of the EPA
PRODUCT HAZARD CLASSIFICATION UNDER SECTION 311 OF SARA
Not applicable
___________________________________________________ __________________________
16. OTHER INFORMATION
NFPA Hazard Rating (National Fire Protection Association)
Health: 1 – Materials that, under emergency conditions, can cause significant irritation.
Fire: 1 – Materials that must be preheated before ignition can occur.
Instability: 0 – Materials that in themselves are normally stable, even under fire exposure conditions.
Reasons For Issue: Revised Section 1
Date Prepared: 02/09/2018
Date of last significant revision:02/09/2018
Component Hazard Phrases
Prepared By: Legal & Compliance Services; E-mail: custinfo@solvay.com
This information is given without any warranty or representation. We do not assume any legal responsibility for same, nor do we give permission,
inducement, or recommendation to practice any patented invention without a license. It is offered solely for your consideration, investigation, and
verification. Before using any product, read its label.
Date Prepared: 02/09/2018
Caprolactam
Page 8 of 8
H302 – Harmful if swallowed.
H315 – Causes skin irritation.
H319 – Causes serious eye irritation.
H332 – Harmful if inhaled.
H335 – May cause respiratory irritation.
Nylon Film/Fabric/Felt SDS: 0059106
by | Sep 27, 2025
by | Sep 27, 2025
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 1 of 8
1. Product and company identification
Product identifier
Trade name: Resin Infusion Products
Knitflow 110, Knitflow 150, PVC Tube, FlowPeel 160-37P16-ESG, Dahltexx SP-2,
Dahltexx SP-3, FlowRunner KF160, Vac-Brake, Vac-Brake Pro, Flowstrip PP4, Flowstrip
PP4 Max, Dahlvac RC Vacuum Hose, Flowlease 160-PP200, PP200, Dahlvac MB80,
Breatherflow 20, Dahlpac MC79, Tube mesh, SpiralMesh, Flowstrip, Flowstrip 39,
Flowstrip 39MAX, Greenflow 75, Greenflow 185, Knitflow 160, Knitflow 105 HT, Resinflow
100, Resinflow 60, Resinflow 20, Resinflow 90HT, Flowlease 160-37P16, Flowlease
75-37P16, Flowlease Blue, Flowlease Black, OF313, OF500, OF750, OF1000, OF625V,
Resintrak, Vactrak, VAC-RIC LT, VAC-RIC HT, RIC, RIC HT, RIA, polyethylene and nylon
tubing, , polyethylene and nylon spiral tubing, nylon fittings (NTF, NEF, NCF), Sil-tube,
HTRIL-S59, Infusion valve, Hose clamps A & B, Flowrunner PP2, Tac-Strip HT, PP150,
Dahlpac HT
Relevant identified uses of the substance or mixture and uses advised against
General use: Article: Resin distribution media and auxiliaries
For industrial purposes only
Details of the supplier of the safety data sheet
Company name:
Airtech International, Inc.
5700 Skylab Road
Huntington Beach, CA 92647
E-mail: airtech@airtechintl.com
Website: www.airtechonline.com
Telephone: +1 714.899.8100
Department responsible for
information:
Telephone: +1 714.899.8100
E-mail: airtech@airtechintl.com
Airtech Europe Sarl
Zone industrielle Haneboesch
L 4562 Differdange
Luxembourg
Website: www.airtech.lu
Telephone: +352 582.282
Department responsible for information:
Telephone: +352 582.282
E-mail: sales@airtech.lu
Airtech Advanced Materials UK Ltd.
The Causeway
Broadway Business Park
Chadderton, Oldham
OL9 9XD United Kingdom
Website: www.airtech-amg.co.uk
Telephone: +44 161.947.1610
Department responsible for
information:
Telephone: +44 161.947.1610
E-mail: sales@airtech-amg.co.uk
Airtech Asia Ltd.
No. 161 of Anyuan Rd
Chagugang County
Wuqing District
301721, Tianjin, P.R. China
Website: www.airtech.asia
Telephone: +86 22 8862 9800
Telefax:: +86 22 8862 9900
Department responsible for information:
Telephone: +86 22 8862 9800
E-mail: airtech.asia@airtechasia.com.cn
Emergency phone number
CHEMTREC EMERGENCY PHONE:
Within USA/Canada: 1-(800)424-9300
International: +1 703-741-5970
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 2 of 8
2. Hazards identification
Emergency overview
Appearance: Form: solid
Color: varying
Odor: odorless
Classification: Article not subject to hazard labelling or classification.
Regulatory status
This material is not considered hazardous by the U.S. OSHA Hazard Communication
Standard (29 CFR 1910.1200).
Hazards not otherwise classified
Toxic fumes may be emitted at elevated temperatures. Do not breathe vapor. Processing,
e.g. by cutting, sawing or grinding, can produce particles and dust. Avoid inhalation of
dusts, as even inert dusts may functionally affect respiratory organs.
see section 11: Toxicological information
3. Composition / Information on ingredients
Chemical characterization:Article: Thermoplastic, Silicone, Fiberglass, Metal
4. First aid measures
In case of inhalation:In case of inhalation of decomposition products, affected person should be moved into
fresh air and kept still. If the casualty has difficulty breathing, call a doctor immediately.
Following skin contact:After contact with molten product, cool skin area rapidly with cold water. Do not peel
solidified product off the skin. Seek medical attention.
After eye contact: In the event of irritation from processing vapors: Immediately flush eyes with plenty of
flowing water for 10 to 15 minutes holding eyelids apart. In case of troubles or persistent
symptoms, consult an opthalmologist.
After swallowing: Not a probable route of exposure.
In the case of the formation of dust: Rinse mouth. Seek medical treatment in case of
troubles.
Most important symptoms/effects, acute and delayed
In case of inhalation:
Inhalation of dust may cause irritation of the respiratory system. Overheating released
mist or vapors can irritate the respiratory tracts.
Other symptoms: Cough, respiratory complaints, dizziness, nausea, vomiting.
After contact with skin: The melted product can cause severe burns.
After eye contact:
Process vapors can irritate the eyes. Dust contact with the eyes can lead to mechanical
irritation.
Information to physician
Treat symptomatically.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 3 of 8
5. Fire fighting measures
Flash point/flash point range:
No data available
Auto-ignition temperature:No data available
Suitable extinguishing media:
Water spray jet, dry chemical powder, foam, carbon dioxide
Extinguishing media which must not be used for safety reasons:
Full water jet.
Specific hazards arising from the chemical
This material is combustible, but will not ignite readily. Toxic fumes may be emitted at
elevated temperatures.
In case of fire may be liberated: Caprolactam, nitrogen oxides (NOx), amines, carbon
monoxide and carbon dioxide.
Protective equipment and precautions for firefighters:
Wear self-contained positive pressure breathing apparatus and full firefighting protective
clothing.
Additional information:Seal off endangered area. Cool endangered containers with water spray and, if possible,
remove from danger zone. Use water spray jet to knock down vapors. Do not breathe
fumes. Do not allow fire water to penetrate into surface or ground water.
6. Accidental release measures
Personal precautions:Handle in accordance with good industrial hygiene and safety practice.
At processing: Avoid the formation of aerosol/vapors. Avoid generation of dust. Avoid
inhalation and contact with skin and eyes. Wear appropriate protective equipment. Keep
unprotected people away. Ensure adequate ventilation, especially in confined areas.
Environmental precautions:
Do not allow to penetrate into soil, waterbodies or drains.
Methods for clean-up:Take up mechanically, placing in appropriate containers for disposal. Dispose of waste
according to applicable legislation.
7. Handling and storage
Handling
Advices on safe handling:Handle in accordance with good industrial hygiene and safety practice.
At processing: Provide adequate ventilation, and local exhaust as needed. Avoid the
formation of aerosol/vapors. Avoid generation of dust. Avoid inhalation and contact with
skin and eyes. Wear appropriate protective equipment. Keep unprotected people away.
When using do not eat, drink or smoke.
Precautions against fire and explosion:
Take standard precautions to prevent fire.
Storage
Requirements for storerooms and containers:
Keep in a cool place. Keep container dry. Protect from direct sunlight. Keep away from
incompatible materials. Store at room temperature.
Hints on joint storage:Incompatible materials: Strong bases, strong acids, strong oxidizing agents.
Keep away from food and drinks.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 4 of 8
8. Exposure controls / personal protection
Exposure guidelines
Occupational exposure limit values:
Type Limit value
USA: ACGIH: TWA 10 mg/m (Dust limit value, inhalable fraction)
USA: ACGIH: TWA 3 mg/m (Dust limit value, respirable fraction)
USA: OSHA: TWA 15 mg/m (Dust limit value, total dust)
USA: OSHA: TWA 5 mg/m (Dust limit value, respirable fraction)
Engineering controls
Provide good ventilation and/or an exhaust system in the work area.
In case of development of vapors or dust (at processing): Use local exhaust.
See also information in chapter 7, section storage.
Personal protection equipment (PPE)
Eye/face protection:At processing (recommended): Safety glasses in accordance with OSHA 29 CFR:
1910.133 or ANSI Z87.1-2010.
Skin protection: At processing (recommended): Wear suitable protective clothing.
Recommendation:
Protective gloves according to OSHA Standard – 29 CFR: 1910.138.
Glove material: nitrile rubber (0.11 mm)
Breakthrough time: 480 min.
Observe glove manufacturer’s instructions concerning penetrability and breakthrough time.
Respiratory protection:Respiratory protection is not necessary if room is well ventilated.
At processing:
When vapors form, use respiratory protection. The filter class must be suitable for the
maximum contaminant concentration (gas/vapor/aerosol/particulates) that may arise
when handling the product. If the concentration is exceeded, self-contained breathing
apparatus must be used.
General hygiene considerations:
Handle in accordance with good industrial hygiene and safety practice. Wash hands
before breaks and after work. When using do not eat, drink or smoke.
At processing:
Avoid contact with skin, eyes, and clothing. Do not breathe vapors. Do not breathe dust.
Environmental exposure controls
Refer to 6.: Section “Environmental precautions”.
9. Physical and chemical properties
Information on basic physical and chemical properties
Appearance: Form: solid
Color: varying
Odor: odorless
Odor threshold: No data available
pH: No data available
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 5 of 8
Melting point/freezing point: 212 – 500 F
Initial boiling point and boiling range:No data available
Flash point/flash point range: No data available
Evaporation rate: No data available
Flammability: This material is combustible, but will not ignite readily.
Explosion limits: No data available
Vapor pressure: No data available
Vapor density: No data available
Density: No data available
Water solubility: at 68 F: insoluble
Partition coefficient: n-octanol/water:No data available
Auto-ignition temperature: No data available
Thermal decomposition: No data available
Additional information: No data available
10. Stability and reactivity
Reactivity: Refer to section: Possibility of hazardous reactions.
Chemical stability: Stable under recommended storage conditions.
Possibility of hazardous reactions:
No dangerous reactions with proper and specified storage and handling
Conditions to avoid:Keep away from heat. Protect from direct sunlight. Avoid generation of dust. Avoid the
formation of aerosol/vapors.
Incompatible materials:Strong acids, strong oxidizing agents.
Hazardous decomposition products:
Caprolactam, nitrogen oxides (NOx), amines, carbon monoxide and carbon dioxide
Thermal decomposition:No data available
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 6 of 8
11. Toxicological information
Toxicological tests
Toxicological effects:Acute toxicity (oral): Lack of data.
Acute toxicity (dermal): Lack of data.
Acute toxicity (inhalative): Lack of data.
Skin corrosion/irritation: Lack of data.
Serious eye damage/irritation: Lack of data.
Sensitisation to the respiratory tract: Lack of data.
Skin sensitisation: Lack of data.
Germ cell mutagenicity/Genotoxicity: Lack of data.
Carcinogenicity: Lack of data.
Reproductive toxicity: Lack of data.
Effects on or via lactation: Lack of data.
Specific target organ toxicity (single exposure): Lack of data.
Specific target organ toxicity (repeated exposure): Lack of data.
Aspiration hazard: Lack of data.
Other information: Toxic fumes may be emitted at elevated temperatures. Processing, e.g. by cutting,
sawing or grinding, can produce particles and dust. Dust may irritate airways and cause
bronchitis symptoms.
Information about Caprolactam: Harmful if swallowed. Harmful if inhaled. Causes skin
irritation. Causes serious eye irritation. May cause respiratory irritation.
Symptoms
In case of inhalation:
Inhalation of dust may cause irritation of the respiratory system. Overheating released
mist or vapors can irritate the respiratory tracts.
Other symptoms: Cough, respiratory complaints, dizziness, nausea, vomiting.
After contact with skin: The melted product can cause severe burns.
After eye contact:
Process vapors can irritate the eyes. Dust contact with the eyes can lead to mechanical
irritation.
12. Ecological information
Ecotoxicity
Further details: No data available
Mobility in soil
No data available
Persistence and degradability
Further details: Product is not biodegradable.
Additional ecological information
General information:Avoid release to the environment.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 7 of 8
13. Disposal considerations
Product
Recommendation: Dispose of waste according to applicable legislation.
Package
Waste key number:
15 01 01 =paper and cardboard packaging or 150102 = Plastic packaging
Recommendation: Dispose of waste according to applicable legislation. Non-contaminated packages may be
recycled.
14. Transport information
UN number
ADR/RID, IMDG, IATA-DGR:
not applicable
UN proper shipping name
ADR/RID, IMDG, IATA-DGR:
Not restricted
Transport hazard class(es)
ADR/RID, IMDG, IATA-DGR:
not applicable
Packing group
ADR/RID, IMDG, IATA-DGR:
not applicable
Environmental hazards
Marine pollutant: no
Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
No data available
USA: Department of Transportation (DOT)
Proper shipping name: Not restricted
Sea transport (IMDG)
Proper shipping name:: Not restricted
Marine pollutant: no
Air transport (IATA)
Proper shipping name:: Not restricted
Further information
No dangerous good in sense of these transport regulations.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 8 of 8
15. Regulatory information
National regulations – U.S. Federal Regulations
This product is an article as defined by TSCA regulations, and is exempt from TSCA
inventory listing requirements.
National regulations – U.S. State Regulations
No data available
National regulations – Great Britain
Hazchem-Code: –
16. Other information
Hazard rating systems:
1
10
NFPA Hazard Rating:
Health: 1 (Slight)
Fire: 1 (Slight)
Reactivity: 0 (Minimal)
HEALTH 1
FLAMMABILITY 1
PHYSICAL HAZARD 0
X
HMIS Version III Rating:
Health: 1 (Slight)
Flammability: 1 (Slight)
Physical Hazard: 0 (Minimal)
Personal Protection: X = Consult your supervisor
Abbreviations and acronyms:
ADN: European Agreement concerning the International Carriage of Dangerous Goods by Inland Waterways
ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
CAS: Chemical Abstracts Service
CFR: Code of Federal Regulations
CLP: Classification, Labelling and Packaging
DMEL: Derived minimal effect level
DNEL: Derived no-effect level
EC: European Community
EN: European Standard
EQ: Excepted quantities
IATA: International Air Transport Association
IATA-DGR: International Air Transport Association Dangerous Goods Regulations
IBC Code: International Code for the Construction and Equipment of Ships carrying Dangerous Chemicals in Bulk
IMDG Code: International Maritime Dangerous Goods Code
MARPOL: Maritime Pollution: The International Convention for the Prevention of Pollution from Ships
OSHA: Occupational Safety and Health Administration
PBT: Persistent, bioaccumulative and toxic
PNEC: Predicted no-effect concentration
RID: Regulations Concerning the International Carriage of Dangerous Goods by Rail
TRGS: Technical Rules for Hazardous Substances
TSCA: Toxic Substance Control Act
vPvB: Very persistent and very bioaccumulative
Reason of change: Changes in section 1: Changes of product list
Department issuing data sheet
Contact person: see section 1: Department responsible for information
This data sheet cannot cover all possible situations which the user may experience during processing. Each aspect of your operation should be
examined to determine if, and which additional precautions may be necessary. All health and safety information contained in this data sheet should be
provided to your employees and customers. It is your responsibility to develop appropriate workplace instructions and training programs for employees.
As the conditions and methods of use are beyond our control, we do not assume any responsibility and expressly disclaim any liability for any use of
this product. The information supplied on this safety data sheet complies with our current level of knowledge as well as with national and EU
regulations. All statements or suggestions are made without warranty, expressed or implied, regarding accuracy of information, the hazards connected
with the use of the product or the results to be obtained from the use thereof.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
by | Sep 27, 2025
by | Sep 27, 2025
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 1 of 8
1. Product and company identification
Product identifier
Trade name: Resin Infusion Products
Knitflow 110, Knitflow 150, PVC Tube, FlowPeel 160-37P16-ESG, Dahltexx SP-2,
Dahltexx SP-3, FlowRunner KF160, Vac-Brake, Vac-Brake Pro, Flowstrip PP4, Flowstrip
PP4 Max, Dahlvac RC Vacuum Hose, Flowlease 160-PP200, PP200, Dahlvac MB80,
Breatherflow 20, Dahlpac MC79, Tube mesh, SpiralMesh, Flowstrip, Flowstrip 39,
Flowstrip 39MAX, Greenflow 75, Greenflow 185, Knitflow 160, Knitflow 105 HT, Resinflow
100, Resinflow 60, Resinflow 20, Resinflow 90HT, Flowlease 160-37P16, Flowlease
75-37P16, Flowlease Blue, Flowlease Black, OF313, OF500, OF750, OF1000, OF625V,
Resintrak, Vactrak, VAC-RIC LT, VAC-RIC HT, RIC, RIC HT, RIA, polyethylene and nylon
tubing, , polyethylene and nylon spiral tubing, nylon fittings (NTF, NEF, NCF), Sil-tube,
HTRIL-S59, Infusion valve, Hose clamps A & B, Flowrunner PP2, Tac-Strip HT, PP150,
Dahlpac HT
Relevant identified uses of the substance or mixture and uses advised against
General use: Article: Resin distribution media and auxiliaries
For industrial purposes only
Details of the supplier of the safety data sheet
Company name:
Airtech International, Inc.
5700 Skylab Road
Huntington Beach, CA 92647
E-mail: airtech@airtechintl.com
Website: www.airtechonline.com
Telephone: +1 714.899.8100
Department responsible for
information:
Telephone: +1 714.899.8100
E-mail: airtech@airtechintl.com
Airtech Europe Sarl
Zone industrielle Haneboesch
L 4562 Differdange
Luxembourg
Website: www.airtech.lu
Telephone: +352 582.282
Department responsible for information:
Telephone: +352 582.282
E-mail: sales@airtech.lu
Airtech Advanced Materials UK Ltd.
The Causeway
Broadway Business Park
Chadderton, Oldham
OL9 9XD United Kingdom
Website: www.airtech-amg.co.uk
Telephone: +44 161.947.1610
Department responsible for
information:
Telephone: +44 161.947.1610
E-mail: sales@airtech-amg.co.uk
Airtech Asia Ltd.
No. 161 of Anyuan Rd
Chagugang County
Wuqing District
301721, Tianjin, P.R. China
Website: www.airtech.asia
Telephone: +86 22 8862 9800
Telefax:: +86 22 8862 9900
Department responsible for information:
Telephone: +86 22 8862 9800
E-mail: airtech.asia@airtechasia.com.cn
Emergency phone number
CHEMTREC EMERGENCY PHONE:
Within USA/Canada: 1-(800)424-9300
International: +1 703-741-5970
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 2 of 8
2. Hazards identification
Emergency overview
Appearance: Form: solid
Color: varying
Odor: odorless
Classification: Article not subject to hazard labelling or classification.
Regulatory status
This material is not considered hazardous by the U.S. OSHA Hazard Communication
Standard (29 CFR 1910.1200).
Hazards not otherwise classified
Toxic fumes may be emitted at elevated temperatures. Do not breathe vapor. Processing,
e.g. by cutting, sawing or grinding, can produce particles and dust. Avoid inhalation of
dusts, as even inert dusts may functionally affect respiratory organs.
see section 11: Toxicological information
3. Composition / Information on ingredients
Chemical characterization:Article: Thermoplastic, Silicone, Fiberglass, Metal
4. First aid measures
In case of inhalation:In case of inhalation of decomposition products, affected person should be moved into
fresh air and kept still. If the casualty has difficulty breathing, call a doctor immediately.
Following skin contact:After contact with molten product, cool skin area rapidly with cold water. Do not peel
solidified product off the skin. Seek medical attention.
After eye contact: In the event of irritation from processing vapors: Immediately flush eyes with plenty of
flowing water for 10 to 15 minutes holding eyelids apart. In case of troubles or persistent
symptoms, consult an opthalmologist.
After swallowing: Not a probable route of exposure.
In the case of the formation of dust: Rinse mouth. Seek medical treatment in case of
troubles.
Most important symptoms/effects, acute and delayed
In case of inhalation:
Inhalation of dust may cause irritation of the respiratory system. Overheating released
mist or vapors can irritate the respiratory tracts.
Other symptoms: Cough, respiratory complaints, dizziness, nausea, vomiting.
After contact with skin: The melted product can cause severe burns.
After eye contact:
Process vapors can irritate the eyes. Dust contact with the eyes can lead to mechanical
irritation.
Information to physician
Treat symptomatically.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 3 of 8
5. Fire fighting measures
Flash point/flash point range:
No data available
Auto-ignition temperature:No data available
Suitable extinguishing media:
Water spray jet, dry chemical powder, foam, carbon dioxide
Extinguishing media which must not be used for safety reasons:
Full water jet.
Specific hazards arising from the chemical
This material is combustible, but will not ignite readily. Toxic fumes may be emitted at
elevated temperatures.
In case of fire may be liberated: Caprolactam, nitrogen oxides (NOx), amines, carbon
monoxide and carbon dioxide.
Protective equipment and precautions for firefighters:
Wear self-contained positive pressure breathing apparatus and full firefighting protective
clothing.
Additional information:Seal off endangered area. Cool endangered containers with water spray and, if possible,
remove from danger zone. Use water spray jet to knock down vapors. Do not breathe
fumes. Do not allow fire water to penetrate into surface or ground water.
6. Accidental release measures
Personal precautions:Handle in accordance with good industrial hygiene and safety practice.
At processing: Avoid the formation of aerosol/vapors. Avoid generation of dust. Avoid
inhalation and contact with skin and eyes. Wear appropriate protective equipment. Keep
unprotected people away. Ensure adequate ventilation, especially in confined areas.
Environmental precautions:
Do not allow to penetrate into soil, waterbodies or drains.
Methods for clean-up:Take up mechanically, placing in appropriate containers for disposal. Dispose of waste
according to applicable legislation.
7. Handling and storage
Handling
Advices on safe handling:Handle in accordance with good industrial hygiene and safety practice.
At processing: Provide adequate ventilation, and local exhaust as needed. Avoid the
formation of aerosol/vapors. Avoid generation of dust. Avoid inhalation and contact with
skin and eyes. Wear appropriate protective equipment. Keep unprotected people away.
When using do not eat, drink or smoke.
Precautions against fire and explosion:
Take standard precautions to prevent fire.
Storage
Requirements for storerooms and containers:
Keep in a cool place. Keep container dry. Protect from direct sunlight. Keep away from
incompatible materials. Store at room temperature.
Hints on joint storage:Incompatible materials: Strong bases, strong acids, strong oxidizing agents.
Keep away from food and drinks.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 4 of 8
8. Exposure controls / personal protection
Exposure guidelines
Occupational exposure limit values:
Type Limit value
USA: ACGIH: TWA 10 mg/m (Dust limit value, inhalable fraction)
USA: ACGIH: TWA 3 mg/m (Dust limit value, respirable fraction)
USA: OSHA: TWA 15 mg/m (Dust limit value, total dust)
USA: OSHA: TWA 5 mg/m (Dust limit value, respirable fraction)
Engineering controls
Provide good ventilation and/or an exhaust system in the work area.
In case of development of vapors or dust (at processing): Use local exhaust.
See also information in chapter 7, section storage.
Personal protection equipment (PPE)
Eye/face protection:At processing (recommended): Safety glasses in accordance with OSHA 29 CFR:
1910.133 or ANSI Z87.1-2010.
Skin protection: At processing (recommended): Wear suitable protective clothing.
Recommendation:
Protective gloves according to OSHA Standard – 29 CFR: 1910.138.
Glove material: nitrile rubber (0.11 mm)
Breakthrough time: 480 min.
Observe glove manufacturer’s instructions concerning penetrability and breakthrough time.
Respiratory protection:Respiratory protection is not necessary if room is well ventilated.
At processing:
When vapors form, use respiratory protection. The filter class must be suitable for the
maximum contaminant concentration (gas/vapor/aerosol/particulates) that may arise
when handling the product. If the concentration is exceeded, self-contained breathing
apparatus must be used.
General hygiene considerations:
Handle in accordance with good industrial hygiene and safety practice. Wash hands
before breaks and after work. When using do not eat, drink or smoke.
At processing:
Avoid contact with skin, eyes, and clothing. Do not breathe vapors. Do not breathe dust.
Environmental exposure controls
Refer to 6.: Section “Environmental precautions”.
9. Physical and chemical properties
Information on basic physical and chemical properties
Appearance: Form: solid
Color: varying
Odor: odorless
Odor threshold: No data available
pH: No data available
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 5 of 8
Melting point/freezing point: 212 – 500 F
Initial boiling point and boiling range:No data available
Flash point/flash point range: No data available
Evaporation rate: No data available
Flammability: This material is combustible, but will not ignite readily.
Explosion limits: No data available
Vapor pressure: No data available
Vapor density: No data available
Density: No data available
Water solubility: at 68 F: insoluble
Partition coefficient: n-octanol/water:No data available
Auto-ignition temperature: No data available
Thermal decomposition: No data available
Additional information: No data available
10. Stability and reactivity
Reactivity: Refer to section: Possibility of hazardous reactions.
Chemical stability: Stable under recommended storage conditions.
Possibility of hazardous reactions:
No dangerous reactions with proper and specified storage and handling
Conditions to avoid:Keep away from heat. Protect from direct sunlight. Avoid generation of dust. Avoid the
formation of aerosol/vapors.
Incompatible materials:Strong acids, strong oxidizing agents.
Hazardous decomposition products:
Caprolactam, nitrogen oxides (NOx), amines, carbon monoxide and carbon dioxide
Thermal decomposition:No data available
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 6 of 8
11. Toxicological information
Toxicological tests
Toxicological effects:Acute toxicity (oral): Lack of data.
Acute toxicity (dermal): Lack of data.
Acute toxicity (inhalative): Lack of data.
Skin corrosion/irritation: Lack of data.
Serious eye damage/irritation: Lack of data.
Sensitisation to the respiratory tract: Lack of data.
Skin sensitisation: Lack of data.
Germ cell mutagenicity/Genotoxicity: Lack of data.
Carcinogenicity: Lack of data.
Reproductive toxicity: Lack of data.
Effects on or via lactation: Lack of data.
Specific target organ toxicity (single exposure): Lack of data.
Specific target organ toxicity (repeated exposure): Lack of data.
Aspiration hazard: Lack of data.
Other information: Toxic fumes may be emitted at elevated temperatures. Processing, e.g. by cutting,
sawing or grinding, can produce particles and dust. Dust may irritate airways and cause
bronchitis symptoms.
Information about Caprolactam: Harmful if swallowed. Harmful if inhaled. Causes skin
irritation. Causes serious eye irritation. May cause respiratory irritation.
Symptoms
In case of inhalation:
Inhalation of dust may cause irritation of the respiratory system. Overheating released
mist or vapors can irritate the respiratory tracts.
Other symptoms: Cough, respiratory complaints, dizziness, nausea, vomiting.
After contact with skin: The melted product can cause severe burns.
After eye contact:
Process vapors can irritate the eyes. Dust contact with the eyes can lead to mechanical
irritation.
12. Ecological information
Ecotoxicity
Further details: No data available
Mobility in soil
No data available
Persistence and degradability
Further details: Product is not biodegradable.
Additional ecological information
General information:Avoid release to the environment.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 7 of 8
13. Disposal considerations
Product
Recommendation: Dispose of waste according to applicable legislation.
Package
Waste key number:
15 01 01 =paper and cardboard packaging or 150102 = Plastic packaging
Recommendation: Dispose of waste according to applicable legislation. Non-contaminated packages may be
recycled.
14. Transport information
UN number
ADR/RID, IMDG, IATA-DGR:
not applicable
UN proper shipping name
ADR/RID, IMDG, IATA-DGR:
Not restricted
Transport hazard class(es)
ADR/RID, IMDG, IATA-DGR:
not applicable
Packing group
ADR/RID, IMDG, IATA-DGR:
not applicable
Environmental hazards
Marine pollutant: no
Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
No data available
USA: Department of Transportation (DOT)
Proper shipping name: Not restricted
Sea transport (IMDG)
Proper shipping name:: Not restricted
Marine pollutant: no
Air transport (IATA)
Proper shipping name:: Not restricted
Further information
No dangerous good in sense of these transport regulations.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 8 of 8
15. Regulatory information
National regulations – U.S. Federal Regulations
This product is an article as defined by TSCA regulations, and is exempt from TSCA
inventory listing requirements.
National regulations – U.S. State Regulations
No data available
National regulations – Great Britain
Hazchem-Code: –
16. Other information
Hazard rating systems:
1
10
NFPA Hazard Rating:
Health: 1 (Slight)
Fire: 1 (Slight)
Reactivity: 0 (Minimal)
HEALTH 1
FLAMMABILITY 1
PHYSICAL HAZARD 0
X
HMIS Version III Rating:
Health: 1 (Slight)
Flammability: 1 (Slight)
Physical Hazard: 0 (Minimal)
Personal Protection: X = Consult your supervisor
Abbreviations and acronyms:
ADN: European Agreement concerning the International Carriage of Dangerous Goods by Inland Waterways
ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
CAS: Chemical Abstracts Service
CFR: Code of Federal Regulations
CLP: Classification, Labelling and Packaging
DMEL: Derived minimal effect level
DNEL: Derived no-effect level
EC: European Community
EN: European Standard
EQ: Excepted quantities
IATA: International Air Transport Association
IATA-DGR: International Air Transport Association Dangerous Goods Regulations
IBC Code: International Code for the Construction and Equipment of Ships carrying Dangerous Chemicals in Bulk
IMDG Code: International Maritime Dangerous Goods Code
MARPOL: Maritime Pollution: The International Convention for the Prevention of Pollution from Ships
OSHA: Occupational Safety and Health Administration
PBT: Persistent, bioaccumulative and toxic
PNEC: Predicted no-effect concentration
RID: Regulations Concerning the International Carriage of Dangerous Goods by Rail
TRGS: Technical Rules for Hazardous Substances
TSCA: Toxic Substance Control Act
vPvB: Very persistent and very bioaccumulative
Reason of change: Changes in section 1: Changes of product list
Department issuing data sheet
Contact person: see section 1: Department responsible for information
This data sheet cannot cover all possible situations which the user may experience during processing. Each aspect of your operation should be
examined to determine if, and which additional precautions may be necessary. All health and safety information contained in this data sheet should be
provided to your employees and customers. It is your responsibility to develop appropriate workplace instructions and training programs for employees.
As the conditions and methods of use are beyond our control, we do not assume any responsibility and expressly disclaim any liability for any use of
this product. The information supplied on this safety data sheet complies with our current level of knowledge as well as with national and EU
regulations. All statements or suggestions are made without warranty, expressed or implied, regarding accuracy of information, the hazards connected
with the use of the product or the results to be obtained from the use thereof.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
by | Sep 27, 2025
by | Sep 27, 2025
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 1 of 8
1. Product and company identification
Product identifier
Trade name: Resin Infusion Products
Knitflow 110, Knitflow 150, PVC Tube, FlowPeel 160-37P16-ESG, Dahltexx SP-2,
Dahltexx SP-3, FlowRunner KF160, Vac-Brake, Vac-Brake Pro, Flowstrip PP4, Flowstrip
PP4 Max, Dahlvac RC Vacuum Hose, Flowlease 160-PP200, PP200, Dahlvac MB80,
Breatherflow 20, Dahlpac MC79, Tube mesh, SpiralMesh, Flowstrip, Flowstrip 39,
Flowstrip 39MAX, Greenflow 75, Greenflow 185, Knitflow 160, Knitflow 105 HT, Resinflow
100, Resinflow 60, Resinflow 20, Resinflow 90HT, Flowlease 160-37P16, Flowlease
75-37P16, Flowlease Blue, Flowlease Black, OF313, OF500, OF750, OF1000, OF625V,
Resintrak, Vactrak, VAC-RIC LT, VAC-RIC HT, RIC, RIC HT, RIA, polyethylene and nylon
tubing, , polyethylene and nylon spiral tubing, nylon fittings (NTF, NEF, NCF), Sil-tube,
HTRIL-S59, Infusion valve, Hose clamps A & B, Flowrunner PP2, Tac-Strip HT, PP150,
Dahlpac HT
Relevant identified uses of the substance or mixture and uses advised against
General use: Article: Resin distribution media and auxiliaries
For industrial purposes only
Details of the supplier of the safety data sheet
Company name:
Airtech International, Inc.
5700 Skylab Road
Huntington Beach, CA 92647
E-mail: airtech@airtechintl.com
Website: www.airtechonline.com
Telephone: +1 714.899.8100
Department responsible for
information:
Telephone: +1 714.899.8100
E-mail: airtech@airtechintl.com
Airtech Europe Sarl
Zone industrielle Haneboesch
L 4562 Differdange
Luxembourg
Website: www.airtech.lu
Telephone: +352 582.282
Department responsible for information:
Telephone: +352 582.282
E-mail: sales@airtech.lu
Airtech Advanced Materials UK Ltd.
The Causeway
Broadway Business Park
Chadderton, Oldham
OL9 9XD United Kingdom
Website: www.airtech-amg.co.uk
Telephone: +44 161.947.1610
Department responsible for
information:
Telephone: +44 161.947.1610
E-mail: sales@airtech-amg.co.uk
Airtech Asia Ltd.
No. 161 of Anyuan Rd
Chagugang County
Wuqing District
301721, Tianjin, P.R. China
Website: www.airtech.asia
Telephone: +86 22 8862 9800
Telefax:: +86 22 8862 9900
Department responsible for information:
Telephone: +86 22 8862 9800
E-mail: airtech.asia@airtechasia.com.cn
Emergency phone number
CHEMTREC EMERGENCY PHONE:
Within USA/Canada: 1-(800)424-9300
International: +1 703-741-5970
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 2 of 8
2. Hazards identification
Emergency overview
Appearance: Form: solid
Color: varying
Odor: odorless
Classification: Article not subject to hazard labelling or classification.
Regulatory status
This material is not considered hazardous by the U.S. OSHA Hazard Communication
Standard (29 CFR 1910.1200).
Hazards not otherwise classified
Toxic fumes may be emitted at elevated temperatures. Do not breathe vapor. Processing,
e.g. by cutting, sawing or grinding, can produce particles and dust. Avoid inhalation of
dusts, as even inert dusts may functionally affect respiratory organs.
see section 11: Toxicological information
3. Composition / Information on ingredients
Chemical characterization:Article: Thermoplastic, Silicone, Fiberglass, Metal
4. First aid measures
In case of inhalation:In case of inhalation of decomposition products, affected person should be moved into
fresh air and kept still. If the casualty has difficulty breathing, call a doctor immediately.
Following skin contact:After contact with molten product, cool skin area rapidly with cold water. Do not peel
solidified product off the skin. Seek medical attention.
After eye contact: In the event of irritation from processing vapors: Immediately flush eyes with plenty of
flowing water for 10 to 15 minutes holding eyelids apart. In case of troubles or persistent
symptoms, consult an opthalmologist.
After swallowing: Not a probable route of exposure.
In the case of the formation of dust: Rinse mouth. Seek medical treatment in case of
troubles.
Most important symptoms/effects, acute and delayed
In case of inhalation:
Inhalation of dust may cause irritation of the respiratory system. Overheating released
mist or vapors can irritate the respiratory tracts.
Other symptoms: Cough, respiratory complaints, dizziness, nausea, vomiting.
After contact with skin: The melted product can cause severe burns.
After eye contact:
Process vapors can irritate the eyes. Dust contact with the eyes can lead to mechanical
irritation.
Information to physician
Treat symptomatically.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 3 of 8
5. Fire fighting measures
Flash point/flash point range:
No data available
Auto-ignition temperature:No data available
Suitable extinguishing media:
Water spray jet, dry chemical powder, foam, carbon dioxide
Extinguishing media which must not be used for safety reasons:
Full water jet.
Specific hazards arising from the chemical
This material is combustible, but will not ignite readily. Toxic fumes may be emitted at
elevated temperatures.
In case of fire may be liberated: Caprolactam, nitrogen oxides (NOx), amines, carbon
monoxide and carbon dioxide.
Protective equipment and precautions for firefighters:
Wear self-contained positive pressure breathing apparatus and full firefighting protective
clothing.
Additional information:Seal off endangered area. Cool endangered containers with water spray and, if possible,
remove from danger zone. Use water spray jet to knock down vapors. Do not breathe
fumes. Do not allow fire water to penetrate into surface or ground water.
6. Accidental release measures
Personal precautions:Handle in accordance with good industrial hygiene and safety practice.
At processing: Avoid the formation of aerosol/vapors. Avoid generation of dust. Avoid
inhalation and contact with skin and eyes. Wear appropriate protective equipment. Keep
unprotected people away. Ensure adequate ventilation, especially in confined areas.
Environmental precautions:
Do not allow to penetrate into soil, waterbodies or drains.
Methods for clean-up:Take up mechanically, placing in appropriate containers for disposal. Dispose of waste
according to applicable legislation.
7. Handling and storage
Handling
Advices on safe handling:Handle in accordance with good industrial hygiene and safety practice.
At processing: Provide adequate ventilation, and local exhaust as needed. Avoid the
formation of aerosol/vapors. Avoid generation of dust. Avoid inhalation and contact with
skin and eyes. Wear appropriate protective equipment. Keep unprotected people away.
When using do not eat, drink or smoke.
Precautions against fire and explosion:
Take standard precautions to prevent fire.
Storage
Requirements for storerooms and containers:
Keep in a cool place. Keep container dry. Protect from direct sunlight. Keep away from
incompatible materials. Store at room temperature.
Hints on joint storage:Incompatible materials: Strong bases, strong acids, strong oxidizing agents.
Keep away from food and drinks.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 4 of 8
8. Exposure controls / personal protection
Exposure guidelines
Occupational exposure limit values:
Type Limit value
USA: ACGIH: TWA 10 mg/m (Dust limit value, inhalable fraction)
USA: ACGIH: TWA 3 mg/m (Dust limit value, respirable fraction)
USA: OSHA: TWA 15 mg/m (Dust limit value, total dust)
USA: OSHA: TWA 5 mg/m (Dust limit value, respirable fraction)
Engineering controls
Provide good ventilation and/or an exhaust system in the work area.
In case of development of vapors or dust (at processing): Use local exhaust.
See also information in chapter 7, section storage.
Personal protection equipment (PPE)
Eye/face protection:At processing (recommended): Safety glasses in accordance with OSHA 29 CFR:
1910.133 or ANSI Z87.1-2010.
Skin protection: At processing (recommended): Wear suitable protective clothing.
Recommendation:
Protective gloves according to OSHA Standard – 29 CFR: 1910.138.
Glove material: nitrile rubber (0.11 mm)
Breakthrough time: 480 min.
Observe glove manufacturer’s instructions concerning penetrability and breakthrough time.
Respiratory protection:Respiratory protection is not necessary if room is well ventilated.
At processing:
When vapors form, use respiratory protection. The filter class must be suitable for the
maximum contaminant concentration (gas/vapor/aerosol/particulates) that may arise
when handling the product. If the concentration is exceeded, self-contained breathing
apparatus must be used.
General hygiene considerations:
Handle in accordance with good industrial hygiene and safety practice. Wash hands
before breaks and after work. When using do not eat, drink or smoke.
At processing:
Avoid contact with skin, eyes, and clothing. Do not breathe vapors. Do not breathe dust.
Environmental exposure controls
Refer to 6.: Section “Environmental precautions”.
9. Physical and chemical properties
Information on basic physical and chemical properties
Appearance: Form: solid
Color: varying
Odor: odorless
Odor threshold: No data available
pH: No data available
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 5 of 8
Melting point/freezing point: 212 – 500 F
Initial boiling point and boiling range:No data available
Flash point/flash point range: No data available
Evaporation rate: No data available
Flammability: This material is combustible, but will not ignite readily.
Explosion limits: No data available
Vapor pressure: No data available
Vapor density: No data available
Density: No data available
Water solubility: at 68 F: insoluble
Partition coefficient: n-octanol/water:No data available
Auto-ignition temperature: No data available
Thermal decomposition: No data available
Additional information: No data available
10. Stability and reactivity
Reactivity: Refer to section: Possibility of hazardous reactions.
Chemical stability: Stable under recommended storage conditions.
Possibility of hazardous reactions:
No dangerous reactions with proper and specified storage and handling
Conditions to avoid:Keep away from heat. Protect from direct sunlight. Avoid generation of dust. Avoid the
formation of aerosol/vapors.
Incompatible materials:Strong acids, strong oxidizing agents.
Hazardous decomposition products:
Caprolactam, nitrogen oxides (NOx), amines, carbon monoxide and carbon dioxide
Thermal decomposition:No data available
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 6 of 8
11. Toxicological information
Toxicological tests
Toxicological effects:Acute toxicity (oral): Lack of data.
Acute toxicity (dermal): Lack of data.
Acute toxicity (inhalative): Lack of data.
Skin corrosion/irritation: Lack of data.
Serious eye damage/irritation: Lack of data.
Sensitisation to the respiratory tract: Lack of data.
Skin sensitisation: Lack of data.
Germ cell mutagenicity/Genotoxicity: Lack of data.
Carcinogenicity: Lack of data.
Reproductive toxicity: Lack of data.
Effects on or via lactation: Lack of data.
Specific target organ toxicity (single exposure): Lack of data.
Specific target organ toxicity (repeated exposure): Lack of data.
Aspiration hazard: Lack of data.
Other information: Toxic fumes may be emitted at elevated temperatures. Processing, e.g. by cutting,
sawing or grinding, can produce particles and dust. Dust may irritate airways and cause
bronchitis symptoms.
Information about Caprolactam: Harmful if swallowed. Harmful if inhaled. Causes skin
irritation. Causes serious eye irritation. May cause respiratory irritation.
Symptoms
In case of inhalation:
Inhalation of dust may cause irritation of the respiratory system. Overheating released
mist or vapors can irritate the respiratory tracts.
Other symptoms: Cough, respiratory complaints, dizziness, nausea, vomiting.
After contact with skin: The melted product can cause severe burns.
After eye contact:
Process vapors can irritate the eyes. Dust contact with the eyes can lead to mechanical
irritation.
12. Ecological information
Ecotoxicity
Further details: No data available
Mobility in soil
No data available
Persistence and degradability
Further details: Product is not biodegradable.
Additional ecological information
General information:Avoid release to the environment.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 7 of 8
13. Disposal considerations
Product
Recommendation: Dispose of waste according to applicable legislation.
Package
Waste key number:
15 01 01 =paper and cardboard packaging or 150102 = Plastic packaging
Recommendation: Dispose of waste according to applicable legislation. Non-contaminated packages may be
recycled.
14. Transport information
UN number
ADR/RID, IMDG, IATA-DGR:
not applicable
UN proper shipping name
ADR/RID, IMDG, IATA-DGR:
Not restricted
Transport hazard class(es)
ADR/RID, IMDG, IATA-DGR:
not applicable
Packing group
ADR/RID, IMDG, IATA-DGR:
not applicable
Environmental hazards
Marine pollutant: no
Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
No data available
USA: Department of Transportation (DOT)
Proper shipping name: Not restricted
Sea transport (IMDG)
Proper shipping name:: Not restricted
Marine pollutant: no
Air transport (IATA)
Proper shipping name:: Not restricted
Further information
No dangerous good in sense of these transport regulations.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Resin Infusion Products
Material number 1074
Revision date: 8/29/2024
Version: 14.5
Replaces version: 14.4
Language: en-US
Date of first version:10/5/2015
Page: 8 of 8
15. Regulatory information
National regulations – U.S. Federal Regulations
This product is an article as defined by TSCA regulations, and is exempt from TSCA
inventory listing requirements.
National regulations – U.S. State Regulations
No data available
National regulations – Great Britain
Hazchem-Code: –
16. Other information
Hazard rating systems:
1
10
NFPA Hazard Rating:
Health: 1 (Slight)
Fire: 1 (Slight)
Reactivity: 0 (Minimal)
HEALTH 1
FLAMMABILITY 1
PHYSICAL HAZARD 0
X
HMIS Version III Rating:
Health: 1 (Slight)
Flammability: 1 (Slight)
Physical Hazard: 0 (Minimal)
Personal Protection: X = Consult your supervisor
Abbreviations and acronyms:
ADN: European Agreement concerning the International Carriage of Dangerous Goods by Inland Waterways
ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
CAS: Chemical Abstracts Service
CFR: Code of Federal Regulations
CLP: Classification, Labelling and Packaging
DMEL: Derived minimal effect level
DNEL: Derived no-effect level
EC: European Community
EN: European Standard
EQ: Excepted quantities
IATA: International Air Transport Association
IATA-DGR: International Air Transport Association Dangerous Goods Regulations
IBC Code: International Code for the Construction and Equipment of Ships carrying Dangerous Chemicals in Bulk
IMDG Code: International Maritime Dangerous Goods Code
MARPOL: Maritime Pollution: The International Convention for the Prevention of Pollution from Ships
OSHA: Occupational Safety and Health Administration
PBT: Persistent, bioaccumulative and toxic
PNEC: Predicted no-effect concentration
RID: Regulations Concerning the International Carriage of Dangerous Goods by Rail
TRGS: Technical Rules for Hazardous Substances
TSCA: Toxic Substance Control Act
vPvB: Very persistent and very bioaccumulative
Reason of change: Changes in section 1: Changes of product list
Department issuing data sheet
Contact person: see section 1: Department responsible for information
This data sheet cannot cover all possible situations which the user may experience during processing. Each aspect of your operation should be
examined to determine if, and which additional precautions may be necessary. All health and safety information contained in this data sheet should be
provided to your employees and customers. It is your responsibility to develop appropriate workplace instructions and training programs for employees.
As the conditions and methods of use are beyond our control, we do not assume any responsibility and expressly disclaim any liability for any use of
this product. The information supplied on this safety data sheet complies with our current level of knowledge as well as with national and EU
regulations. All statements or suggestions are made without warranty, expressed or implied, regarding accuracy of information, the hazards connected
with the use of the product or the results to be obtained from the use thereof.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
by | Sep 27, 2025
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Bagging Films
Material number 1025
Revision date: 10/5/2023
Version: 7.6
Replaces version: 7.5
Language: en-US
Date of first version:10/21/2014
Page: 1 of 8
1. Product and company identification
Product identifier
Trade name: Bagging Films
NBF125C, Big Blue L-100, Securlon V-45, Securlon L-500Y, Securlon L-1000,
Securlon L-2000, Securlon L2000 Embossed, Stretchlon 200, Stretchlon 700,
Stretchlon 800, Stretchlon 850, Stretchlon HT-350, Ipplon KM1300, Ipplon
DP1000, Ipplon DPT1000, Ipplon WN1500, Wrightlon 600V, Wrightlon 5400,
Wrightlon 7400, Wrightlon 8400, Dahlar Release Bag 125, Dahlar Release Bag
375R, Dahlar Release Bag 460, Dahlar Release Bag 500, Econolon, Airdraw 2,
Airdraw 2-DC, Thermalimide, Thermaflex
Relevant identified uses of the substance or mixture and uses advised against
General use: Article: Vacuum bagging film
Details of the supplier of the safety data sheet
Company name:
Airtech International, Inc.
5700 Skylab Road
Huntington Beach, CA 92647
E-mail: airtech@airtechintl.com
Website: www.airtechonline.com
Telephone: +1 714.899.8100
Department responsible for
information:
Telephone: +1 714.899.8100
E-mail: airtech@airtechintl.com
Airtech Europe Sarl
Zone industrielle Haneboesch
L 4562 Differdange
Luxembourg
Website: www.airtech.lu
Telephone: +352 582.282
Department responsible for information:
Telephone: +352 582.282
E-mail: sales@airtech.lu
Airtech Advanced Materials UK Ltd.
The Causeway
Broadway Business Park
Chadderton, Oldham
OL9 9XD United Kingdom
Website: www.airtech-amg.co.uk
Telephone: +44 161.947.1610
Department responsible for
information:
Telephone: +44 161.947.1610
E-mail: sales@airtech-amg.co.uk
Airtech Asia Ltd.
No. 161 of Anyuan Rd
Chagugang County
Wuqing District
301721, Tianjin, P.R. China
Website: www.airtech.asia
Telephone: +86 22 8862 9800
Telefax:: +86 22 8862 9900
Department responsible for information:
Telephone: +86 22 8862 9800
E-mail: airtech.asia@airtechasia.com.cn
Emergency phone number
CHEMTREC EMERGENCY PHONE:
Within USA/Canada: 1-(800)424-9300
International: +1 703-741-5970
Article not subject to hazard labelling or classification.
not applicable
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Bagging Films
Material number 1025
Revision date: 10/5/2023
Version: 7.6
Replaces version: 7.5
Language: en-US
Date of first version:10/21/2014
Page: 2 of 8
Other hazards
Toxic fumes may be emitted at elevated temperatures. Do not breathe vapor. Processing,
e.g. by cutting, sawing or grinding, can produce particles and dust. Avoid inhalation of
dusts, as even inert dusts may functionally affect respiratory organs.
Endocrine disrupting properties, Results of PBT and vPvB assessment:
No data available
2. Composition / Information on ingredients
Chemical characterization:Thermoplastic films
3. First aid measures
In case of inhalation:In case of inhalation of decomposition products, affected person should be moved into
fresh air and kept still. If the casualty has difficulty breathing, call a doctor immediately.
Following skin contact:After contact with molten product, cool skin area rapidly with cold water. Do not peel
solidified product off the skin. Seek medical attention.
After eye contact: In the event of irritation from processing vapors: Immediately flush eyes with plenty of
flowing water for 10 to 15 minutes holding eyelids apart. In case of troubles or persistent
symptoms, consult an opthalmologist.
After swallowing: Not a probable route of exposure.
In the case of the formation of dust: Rinse mouth. Seek medical treatment in case of
troubles.
4.2 Most important symptoms/effects, acute and delayed
In case of inhalation:
Inhalation of dust may cause irritation of the respiratory system. Overheating released
mist or vapors can irritate the respiratory tracts.
Other symptoms: Cough, respiratory complaints, dizziness, nausea, vomiting.
After contact with skin: The melted product can cause severe burns.
After eye contact:
Process vapors can irritate the eyes. Dust contact with the eyes can lead to mechanical
irritation.
4.3 Indication of any immediate medical attention and special treatment needed
Treat symptomatically.
Suitable extinguishing media:
Water spray jet, dry chemical powder, foam, carbon dioxide
Extinguishing media which must not be used for safety reasons:
Full water jet.
Specific hazards arising from the chemical
This material is combustible, but will not ignite readily. Toxic fumes may be emitted at
elevated temperatures.
In case of fire may be liberated: Caprolactam, nitrogen oxides (NOx), amines, carbon
monoxide and carbon dioxide, hydrogen cyanide, isocyanates, isocyanic acid.
Protective equipment and precautions for firefighters:
Wear a self-contained breathing apparatus and chemical protective clothing.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Bagging Films
Material number 1025
Revision date: 10/5/2023
Version: 7.6
Replaces version: 7.5
Language: en-US
Date of first version:10/21/2014
Page: 3 of 8
Additional information:Seal off endangered area. Cool endangered containers with water spray and, if possible,
remove from danger zone. Use water spray jet to knock down vapors. Do not breathe
fumes. Do not allow fire water to penetrate into surface or ground water.
SECTION 6: Accidental release measures
6.1 Personal precautions, protective equipment and emergency procedures
Handle in accordance with good industrial hygiene and safety practice.
At processing: Avoid the formation of aerosol/vapors. Avoid generation of dust. Avoid
inhalation and contact with skin and eyes. Wear appropriate protective equipment. Keep
unprotected people away. Ensure adequate ventilation, especially in confined areas.
6.2 Environmental precautions
Do not allow to penetrate into soil, waterbodies or drains.
6.3 Methods and material for containment and cleaning up
Take up mechanically, placing in appropriate containers for disposal. Dispose of waste
according to applicable legislation.
6.4 Reference to other sections
Refer additionally to section 8 and 13.
SECTION 7: Handling and storage
7.1 Precautions for safe handling
Advices on safe handling:Handle in accordance with good industrial hygiene and safety practice.
At processing: Provide adequate ventilation, and local exhaust as needed. Avoid the
formation of aerosol/vapors. Avoid generation of dust. Avoid inhalation and contact with
skin and eyes. Wear appropriate protective equipment. Keep unprotected people away.
When using do not eat, drink or smoke.
Precautions against fire and explosion:
Take standard precautions to prevent fire.
Storage
Requirements for storerooms and containers:
Keep in a cool place. Keep container dry. Protect from direct sunlight. Keep away from
incompatible materials. Store at room temperature.
Hints on joint storage:Incompatible materials: Strong bases, strong acids, strong oxidizing agents.
Keep away from food and drinks.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Bagging Films
Material number 1025
Revision date: 10/5/2023
Version: 7.6
Replaces version: 7.5
Language: en-US
Date of first version:10/21/2014
Page: 4 of 8
6. Exposure controls / personal protection
Exposure guidelines
Occupational exposure limit values:
Type Limit value
USA: ACGIH: TWA 10 mg/m (Dust limit value, inhalable fraction)
USA: ACGIH: TWA 3 mg/m (Dust limit value, respirable fraction)
USA: OSHA: TWA 15 mg/m (Dust limit value, total dust)
USA: OSHA: TWA 5 mg/m (Dust limit value, respirable fraction)
Engineering controls
Provide good ventilation and/or an exhaust system in the work area.
In case of development of vapors or dust (at processing): Use local exhaust.
See also information in chapter 7, section storage.
Respiratory protection:Respiratory protection is not necessary if room is well ventilated.
At processing:
When vapors form, use respiratory protection. The filter class must be suitable for the
maximum contaminant concentration (gas/vapor/aerosol/particulates) that may arise
when handling the product. If the concentration is exceeded, self-contained breathing
apparatus must be used.
Recommendation:
Protective gloves according to OSHA Standard – 29 CFR: 1910.138.
Glove material: nitrile rubber (0.11 mm)
Breakthrough time: 480 min.
Observe glove manufacturer’s instructions concerning penetrability and breakthrough time.
Personal protection equipment (PPE)
Eye/face protection:At processing (recommended): Safety glasses in accordance with OSHA 29 CFR:
1910.133 or ANSI Z87.1-2010.
Skin protection: At processing (recommended): Wear suitable protective clothing.
General hygiene considerations:
Handle in accordance with good industrial hygiene and safety practice. Wash hands
before breaks and after work. When using do not eat, drink or smoke.
At processing:
Avoid contact with skin, eyes, and clothing. Do not breathe vapors. Do not breathe dust.
Environmental exposure controls
Refer to 6.: Section “Environmental precautions”.
7. Physical and chemical properties
Information on basic physical and chemical properties
Appearance: Form: solid
Color: varying
Odor: odorless
Odor threshold: No data available
pH: No data available
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Bagging Films
Material number 1025
Revision date: 10/5/2023
Version: 7.6
Replaces version: 7.5
Language: en-US
Date of first version:10/21/2014
Page: 5 of 8
Melting point/freezing point: No data available
Initial boiling point and boiling range:No data available
Flash point/flash point range: No data available
Flammability: This material is combustible, but will not ignite readily.
Upper/lower flammability or explosive limits:No data available
Vapor pressure: No data available
Vapor density: No data available
Density: No data available
Water solubility: at 68 F: insoluble
Partition coefficient: n-octanol/water:No data available
Auto-ignition temperature: No data available
Thermal decomposition: No data available
Auto-ignition temperature: No data available
Additional information: No data available
SECTION 10: Stability and reactivity
10.1 Reactivity
Refer to section: Possibility of hazardous reactions.
Chemical stability: Stable under recommended storage conditions.
Possibility of hazardous reactions:
No dangerous reactions with proper and specified storage and handling
Conditions to avoid:Keep away from heat. Protect from direct sunlight. Avoid generation of dust. Avoid the
formation of aerosol/vapors.
Incompatible materials:Strong bases, strong acids, strong oxidizing agents.
Hazardous decomposition products:
Caprolactam, nitrogen oxides (NOx), amines, carbon monoxide and carbon dioxide,
hydrogen cyanide, isocyanates, isocyanic acid.
Thermal decomposition:No data available
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Bagging Films
Material number 1025
Revision date: 10/5/2023
Version: 7.6
Replaces version: 7.5
Language: en-US
Date of first version:10/21/2014
Page: 6 of 8
9. Toxicological information
Toxicological tests
Toxicological effects:The statements are derived from the properties of the single components. No toxicological
data is available for the product as such.
Acute toxicity (oral): Lack of data.
Acute toxicity (dermal): Lack of data.
Acute toxicity (inhalative): Lack of data.
Skin corrosion/irritation: Lack of data.
Serious eye damage/irritation: Lack of data.
Sensitisation to the respiratory tract: Lack of data.
Skin sensitisation: Lack of data.
Germ cell mutagenicity/Genotoxicity: Lack of data.
Carcinogenicity: Lack of data.
Reproductive toxicity: Lack of data.
Effects on or via lactation: Lack of data.
Specific target organ toxicity (single exposure): Lack of data.
Specific target organ toxicity (repeated exposure): Lack of data.
Aspiration hazard: Lack of data.
Other information: Toxic fumes may be emitted at elevated temperatures. Processing, e.g. by cutting,
sawing or grinding, can produce particles and dust. Dust may irritate airways and cause
bronchitis symptoms.
Information about Caprolactam: Harmful if swallowed. Harmful if inhaled. Causes skin
irritation. Causes serious eye irritation. May cause respiratory irritation.
Symptoms
In case of inhalation:
Inhalation of dust may cause irritation of the respiratory system. Overheating released
mist or vapors can irritate the respiratory tracts.
Other symptoms: Cough, respiratory complaints, dizziness, nausea, vomiting.
After contact with skin: The melted product can cause severe burns.
After eye contact:
Process vapors can irritate the eyes. Dust contact with the eyes can lead to mechanical
irritation.
10. Ecological information
Ecotoxicity
Further details: No data available
Persistence and degradability
Further details: Product is not biodegradable.
Bioaccumulative potential
Partition coefficient: n-octanol/water:
No data available
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Bagging Films
Material number 1025
Revision date: 10/5/2023
Version: 7.6
Replaces version: 7.5
Language: en-US
Date of first version:10/21/2014
Page: 7 of 8
Mobility in soil
No data available
Results of PBT and vPvB assessment
No data available
Additional ecological information
General information:Avoid release to the environment.
11. Disposal considerations
Product
Recommendation: Dispose of waste according to applicable legislation. Recycling or special waste
incineration.
Package
Recommendation: Dispose of waste according to applicable legislation. Non-contaminated packages may be
recycled.
12. Transport information
UN number
ADR/RID, IMDG, IATA-DGR:
not applicable
UN proper shipping name
ADR/RID, IMDG, IATA-DGR:
Not restricted
Transport hazard class(es)
ADR/RID, IMDG, IATA-DGR:
not applicable
Packing group
ADR/RID, IMDG, IATA-DGR:
not applicable
Environmental hazards
Marine pollutant: no
14.6 Special precautions for user
USA: Department of Transportation (DOT)
Proper shipping name: Not restricted
Sea transport (IMDG)
Proper shipping name:: Not restricted
Marine pollutant: no
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
Safety information sheet
Voluntary product information following the Safety Data Sheet format
Bagging Films
Material number 1025
Revision date: 10/5/2023
Version: 7.6
Replaces version: 7.5
Language: en-US
Date of first version:10/21/2014
Page: 8 of 8
Air transport (IATA)
Proper shipping name:: Not restricted
Further information
No dangerous good in sense of these transport regulations.
Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
No data available
National regulations – U.S. Federal Regulations
This product is an article as defined by TSCA regulations, and is exempt from TSCA
inventory listing requirements.
National regulations – U.S. State Regulations
No data available
National regulations – Great Britain
Hazchem-Code: –
Further regulations, limitations and legal requirements
For this mixture a chemical safety assessment is not required.
13. Other information
Abbreviations and acronyms:
ADN: European Agreement concerning the International Carriage of Dangerous Goods by Inland Waterways
ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
CAS: Chemical Abstracts Service
CFR: Code of Federal Regulations
CLP: Classification, Labelling and Packaging
DMEL: Derived minimal effect level
DNEL: Derived no-effect level
EC: European Community
EN: European Standard
EQ: Excepted quantities
IATA: International Air Transport Association
IATA-DGR: International Air Transport Association Dangerous Goods Regulations
IBC Code: International Code for the Construction and Equipment of Ships carrying Dangerous Chemicals in Bulk
IMDG Code: International Maritime Dangerous Goods Code
MARPOL: Maritime Pollution: The International Convention for the Prevention of Pollution from Ships
OSHA: Occupational Safety and Health Administration
PBT: Persistent, bioaccumulative and toxic
PNEC: Predicted no-effect concentration
RID: Regulations Concerning the International Carriage of Dangerous Goods by Rail
TRGS: Technical Rules for Hazardous Substances
TSCA: Toxic Substance Control Act
vPvB: Very persistent and very bioaccumulative
Reason of change: Changes in section 1: Changes of product list
Department issuing data sheet
Contact person: see section 1: Department responsible for information
This data sheet cannot cover all possible situations which the user may experience during processing. Each aspect of your operation should be
examined to determine if, and which additional precautions may be necessary. All health and safety information contained in this data sheet should be
provided to your employees and customers. It is your responsibility to develop appropriate workplace instructions and training programs for employees.
As the conditions and methods of use are beyond our control, we do not assume any responsibility and expressly disclaim any liability for any use of
this product. The information supplied on this safety data sheet complies with our current level of knowledge as well as with national and EU
regulations. All statements or suggestions are made without warranty, expressed or implied, regarding accuracy of information, the hazards connected
with the use of the product or the results to be obtained from the use thereof.
printed by Airtech Advanced Materials Group with Qualisys SUMDAT
