by | Sep 27, 2025
1PRODUCT AND COMPANY IDENTIFICATION
2HAZARDS IDENTIFICATION
3COMPOSITION INFORMATION ON INGREDIENTS
4FIRST AID MEASURES
5FIRE HAZARD
6ACCIDENTAL RELEASE MEASURES
Environment Procedure Unnecessary
Clean Up Method Recover mechanically and dispose of according to applicable regulations.
Special Firefighting Equipment Wear self-contained breathing apparatus.
Saw dust
balsa saw dust is explosive in certain concentration in the air. Use dust absorbing system which has spark detector and
automatic CO2 extinguishing system.
Personal Protections Unnecessary
Ingestion drink water or, if large quantities have been ingested, seek medical attention.
Extinguishing Media Unrestricted – carbon dioxide, extinguishing powder, foam & water
Special Firefighting Exposure Do not breathe. Emits toxic fumes under fire conditions like carbon dioxide and carbon monoxide.
Skin Contact
Flush with water or wash with soap and water, do not blow. If molten EVA comes in contact with skin, do not pull from
skin, but cool with water.
Inhalation of Dust
evacuate individual to clear air area, if difficulty in breathing persists, administer oxygen, if breathing stops or asphyxia is
apparent, administer CPR and call for emergency assistance. Keep individual warm and quite.
Inhalation of Gas in the Event of FireMove to fresh air and consult physician.
Description
Continuous filament E Glass and Ethylene Vinyl Acetate non-hazardous above minimum concentrations
Note: cutting, milling, routing, sanding or otherwise abrading this material may render airborne components subject to
PEL TWA = 15mg/m3.
Clothes Contact Unnecessary
Eye Contact flush eye, upper lid and lower lid with water; seek medical attention if irritation persists
When grinding, sanding or sawing, a fine dust will be produced.
Phone (256) 739-6627
Fax (256) 739-4334
General This product is not hazardous and poses no risk to public health or the environment if used as intended.
Use of Product Core material used in sandwich construction
Manufacturer/Converter I-Core Composites, LLC
Physical Location 802 23rd Street S.W., Cullman, AL 35055 – USA
Safety Data Sheet
Product Name
EG Balsa Contourable Panels including EG Balsa GC, EG Balsa GCP, EG Balsa GCPG, EG Balsa GPGS, EG Balsa GPS, EG
Balsa GFX, EG Balsa GFXP, EG Balsa IC, EG Balsa ICP, EG Balsa LC, EG Balsa LCP, EG Balsa LCPG, EG Balsa LPGS, EG Balsa PC,
EG Balsa PCP, EG Balsa PCPG, EG Balsa UC, EG Balsa UCP, EG Balsa UCPG, EG Balsa Armor GC, EG Balsa Armor GCG, EG
Balsa Armor GSC, EG Balsa Armor GCP, EG Balsa Armor GCPG, EG Balsa Armor GPGS, EG Balsa Armor GFX, EG Balsa Armor
GFXP, EG Balsa Armor LC, EG Balsa Armor LCP, EG Balsa Armor LCPG, EG Balsa Armor LPGS, EG Balsa Armor PC, EG Balsa
Armor PCP, EG Balsa Armor PCPG, EG Balsa Armor UC, EG Balsa Armor UCP, EG Balsa Armor UCPG
EG Balsa Rigid Panels including EG Balsa Rigid Panels including EG Balsa GR, EG Balsa GRP, EG Balsa GRS, EG Balsa GRPG,
EG Balsa IR, EG Balsa IRP, EG Balsa IRPG, EG Balsa LR, EG Balsa LRP, EG Balsa LRPG, EG Balsa PR, EG Balsa PRP, EG Balsa
PRPG, EG Balsa UR, EG Balsa URP, EG Balsa URPG, EG Balsa URSC, EG Balsa FS, EG Balsa Armor GR, EG Balsa Armor GRP,
EG Balsa Armor GRPG, EG Balsa Armor LR, EG Balsa Armor LRP, EG Balsa Armor LRPG, EG Balsa Armor PR, EG Balsa Armor
PRP, EG Balsa Armor PRPG, EG Balsa Armor UR, EG Balsa Armor URP, EG Balsa Armor URPG, LR Flat Grain
Product Identification Rigid, Scored, Scrimmed, Perforated, flat grain or Coated Balsa Wood Panels
I-Core Composites, LLC
802 23rd Street SW
Cullman, AL 35055
Ph (256) 739-6627
Fx (256) 739-4334 1
Safety Data Sheet
7HANDLING AND STORAGE
None
8EXPOSURE CONTROLS / PERSONAL PROTECTION
9PHYSICAL AND CHEMICAL PROPERTIES
Water Solubility (20 C)
Boiling Point: N/A
10STABILITY AND REACTIVITY
11TOXICOLOGICAL INFORMATION
12ECOLOGICAL INFORMATION
13DISPOSAL CONSIDERATIONS
14TRANSPORT INFORMATION
15REGULATORY INFORMATION
16OTHER INFORMATION
October 10, 2024
I-Core Composites, Chris Gattiker
This product is not a “Hazardous Chemical”.
Last revision
by
This Safety Data Sheet cancels and replaces any previous edition. The data in this safety data sheet describes the safety requirements of our product and may not be
considered to guaranteeing any product properties. The data in this safety data sheet correspond to our current level of knowledge. We recommend the sharing of this
information with other potential customers and final users. The information reported is based on available knowledge on safety precautions of the product at issue
date. I-Core Composites, LLC does not accept responsibility for workers’ behaviors that are non-conforming to the contents of this document. We have no knowledge of
or control over the working conditions. The users are directly responsible for both their industrial hygiene and their waste disposal.
Degradability Product degrades biologically.
Product Disposal
Balsa dust does not contain any hazardous substances. However, as stated above, dust inhalation, or collection of dust on
floors may cause injury or a hazardous condition to exist.
Use of brooms, vacuums and dust removal systems are recommended. A shop vacuum is a useful tool for dust and debris
removal from floors and work areas.
User of product should review local, state, and federal regulations concerning health and pollution disposal procedures
to assure its compliance with disposal.
Be aware of high concentration of balsa wood dust in the air => explosion risk and respiratory problems.
Transportation Product is not classified for any kind of transportation regulation.
Eye Contact Dust may cause irritation.
Inhalation Dust may cause irritation of the respiratory tract.
Water Product is not water soluble and has no known effects on ground water.
Hazardous Decomposition Products No decomposition if used as intended.
General
When used and handled according to specification, the product does not have any harmful effects according to our
experience and knowledge.
Contact with Skin No known allergic reactions. Dust may cause irritation on sensitive skin.
Conditions to Avoid Avoid exposure to flames.
Exposure Limits Not applicable
Appearance: wood end grain Odor: None Explosive Properties: None
Density: 80-250 kg/m Melting Point: N/A Lower Explosion Limit: None
Color: white – clear brown Ignition temp: > 200 C Upper Explosion Limit: None
General Information Under normal conditions, product is stable.
Storage
Product is combustible wood and fiberglass and should be stored in cool, dry location away from open flame, heat
sources or other means of ignition.
Separation of Incompatible Products
Grinding, Sanding & Sawing
Use of a dust/mist respirator approved by NIOSH/MSMA (TC-21C-132) is recommended whenever use of product results
in creation of dust.
Safe Handling Design all working procedures principally to avoid inhalation of dust and eye contact.
I-Core Composites, LLC
802 23rd Street SW
Cullman, AL 35055
Ph (256) 739-6627
Fx (256) 739-4334 2
by | Sep 27, 2025
1PRODUCT AND COMPANY IDENTIFICATION
2HAZARDS IDENTIFICATION
3COMPOSITION INFORMATION ON INGREDIENTS
4FIRST AID MEASURES
5FIRE HAZARD
6ACCIDENTAL RELEASE MEASURES
Safety Data Sheet
Product Name
EG Balsa Contourable Panels including EG Balsa GC, EG Balsa GCP, EG Balsa GCPG, EG Balsa GPGS, EG Balsa GPS, EG
Balsa GFX, EG Balsa GFXP, EG Balsa IC, EG Balsa ICP, EG Balsa LC, EG Balsa LCP, EG Balsa LCPG, EG Balsa LPGS, EG Balsa PC,
EG Balsa PCP, EG Balsa PCPG, EG Balsa UC, EG Balsa UCP, EG Balsa UCPG, EG Balsa Armor GC, EG Balsa Armor GCG, EG
Balsa Armor GSC, EG Balsa Armor GCP, EG Balsa Armor GCPG, EG Balsa Armor GPGS, EG Balsa Armor GFX, EG Balsa Armor
GFXP, EG Balsa Armor LC, EG Balsa Armor LCP, EG Balsa Armor LCPG, EG Balsa Armor LPGS, EG Balsa Armor PC, EG Balsa
Armor PCP, EG Balsa Armor PCPG, EG Balsa Armor UC, EG Balsa Armor UCP, EG Balsa Armor UCPG
EG Balsa Rigid Panels including EG Balsa Rigid Panels including EG Balsa GR, EG Balsa GRP, EG Balsa GRS, EG Balsa GRPG,
EG Balsa IR, EG Balsa IRP, EG Balsa IRPG, EG Balsa LR, EG Balsa LRP, EG Balsa LRPG, EG Balsa PR, EG Balsa PRP, EG Balsa
PRPG, EG Balsa UR, EG Balsa URP, EG Balsa URPG, EG Balsa URSC, EG Balsa FS, EG Balsa Armor GR, EG Balsa Armor GRP,
EG Balsa Armor GRPG, EG Balsa Armor LR, EG Balsa Armor LRP, EG Balsa Armor LRPG, EG Balsa Armor PR, EG Balsa Armor
PRP, EG Balsa Armor PRPG, EG Balsa Armor UR, EG Balsa Armor URP, EG Balsa Armor URPG, LR Flat Grain
Product Identification Rigid, Scored, Scrimmed, Perforated, flat grain or Coated Balsa Wood Panels
Use of Product Core material used in sandwich construction
Manufacturer/Converter I-Core Composites, LLC
Physical Location 802 23rd Street S.W., Cullman, AL 35055 – USA
Phone (256) 739-6627
Fax (256) 739-4334
General This product is not hazardous and poses no risk to public health or the environment if used as intended.
When grinding, sanding or sawing, a fine dust will be produced.
Description
Continuous filament E Glass and Ethylene Vinyl Acetate non-hazardous above minimum concentrations
Note: cutting, milling, routing, sanding or otherwise abrading this material may render airborne components subject to
PEL TWA = 15mg/m3.
Clothes Contact Unnecessary
Eye Contact flush eye, upper lid and lower lid with water; seek medical attention if irritation persists
Skin Contact
Flush with water or wash with soap and water, do not blow. If molten EVA comes in contact with skin, do not pull from
skin, but cool with water.
Inhalation of Dust
evacuate individual to clear air area, if difficulty in breathing persists, administer oxygen, if breathing stops or asphyxia is
apparent, administer CPR and call for emergency assistance. Keep individual warm and quite.
Inhalation of Gas in the Event of FireMove to fresh air and consult physician.
Ingestion drink water or, if large quantities have been ingested, seek medical attention.
Extinguishing Media Unrestricted – carbon dioxide, extinguishing powder, foam & water
Special Firefighting Exposure Do not breathe. Emits toxic fumes under fire conditions like carbon dioxide and carbon monoxide.
Special Firefighting Equipment Wear self-contained breathing apparatus.
Saw dust
balsa saw dust is explosive in certain concentration in the air. Use dust absorbing system which has spark detector and
automatic CO2 extinguishing system.
Personal Protections Unnecessary
Environment Procedure Unnecessary
Clean Up Method Recover mechanically and dispose of according to applicable regulations.
I-Core Composites, LLC
802 23rd Street SW
Cullman, AL 35055
Ph (256) 739-6627
Fx (256) 739-4334 1
Safety Data Sheet
7HANDLING AND STORAGE
None
8EXPOSURE CONTROLS / PERSONAL PROTECTION
9PHYSICAL AND CHEMICAL PROPERTIES
Water Solubility (20 C)
Boiling Point: N/A
10STABILITY AND REACTIVITY
11TOXICOLOGICAL INFORMATION
12ECOLOGICAL INFORMATION
13DISPOSAL CONSIDERATIONS
14TRANSPORT INFORMATION
15REGULATORY INFORMATION
16OTHER INFORMATION
May 24, 2022
I-Core Composites, Chris Gattiker
Safe Handling Design all working procedures principally to avoid inhalation of dust and eye contact.
Storage
Product is combustible wood and fiberglass and should be stored in cool, dry location away from open flame, heat
sources or other means of ignition.
Separation of Incompatible Products
Grinding, Sanding & Sawing
Use of a dust/mist respirator approved by NIOSH/MSMA (TC-21C-132) is recommended whenever use of product results
in creation of dust.
Conditions to Avoid Avoid exposure to flames.
Exposure Limits Not applicable
Appearance: wood end grain Odor: None Explosive Properties: None
Density: 80-250 kg/m Melting Point: N/A Lower Explosion Limit: None
Color: white – clear brown Ignition temp: > 200 C Upper Explosion Limit: None
General Information Under normal conditions, product is stable.
Hazardous Decomposition Products No decomposition if used as intended.
General
When used and handled according to specification, the product does not have any harmful effects according to our
experience and knowledge.
Contact with Skin No known allergic reactions. Dust may cause irritation on sensitive skin.
Eye Contact Dust may cause irritation.
Inhalation Dust may cause irritation of the respiratory tract.
Water Product is not water soluble and has no known effects on ground water.
This product is not a “Hazardous Chemical”.
Last revision
by
This Safety Data Sheet cancels and replaces any previous edition. The data in this safety data sheet describes the safety requirements of our product and may not be
considered to guaranteeing any product properties. The data in this safety data sheet correspond to our current level of knowledge. We recommend the sharing of this
information with other potential customers and final users. The information reported is based on available knowledge on safety precautions of the product at issue
date. I-Core Composites, LLC does not accept responsibility for workers’ behaviors that are non-conforming to the contents of this document. We have no knowledge of
or control over the working conditions. The users are directly responsible for both their industrial hygiene and their waste disposal.
Degradability Product degrades biologically.
Product Disposal
Balsa dust does not contain any hazardous substances. However, as stated above, dust inhalation, or collection of dust on
floors may cause injury or a hazardous condition to exist.
Use of brooms, vacuums and dust removal systems are recommended. A shop vacuum is a useful tool for dust and debris
removal from floors and work areas.
User of product should review local, state, and federal regulations concerning health and pollution disposal procedures
to assure its compliance with disposal.
Be aware of high concentration of balsa wood dust in the air => explosion risk and respiratory problems.
Transportation Product is not classified for any kind of transportation regulation.
I-Core Composites, LLC
802 23rd Street SW
Cullman, AL 35055
Ph (256) 739-6627
Fx (256) 739-4334 2
by | Sep 27, 2025
1 PRODUCT AND COMPANY IDENTIFICATION
2 HAZARDS IDENTIFICATION
3 COMPOSITION INFORMATION ON INGREDIENTS
4FIRST AID MEASURES
5 FIRE HAZARD
6 ACCIDENTAL RELEASE MEASURES
Safety Data Sheet
Product Name
EG Balsa Contourable Panels including EG Balsa GC, EG Balsa GCP, EG Balsa GCPG, EG Balsa GPGS, EG Balsa GPS, EG
Balsa GFX, EG Balsa GFXP, EG Balsa IC, EG Balsa ICP, EG Balsa LC, EG Balsa LCP, EG Balsa LCPG, EG Balsa LPGS, EG Balsa
PC, EG Balsa PCP,
EG Balsa PCPG, EG Balsa UC, EG Balsa UCP, EG Balsa UCPG, EG Balsa Armor GC, EG Balsa Armor GCG,
EG Balsa Armor GSC, EG Balsa Armor GCP, EG Balsa Armor GCPG, EG Balsa Armor GPGS, EG Balsa Armor GFX, EG Balsa
Armor GFXP, EG Balsa Armor LC, EG Balsa
Armor LCP, EG Balsa Armor LCPG, EG Balsa Armor LPGS, EG Balsa Armor PC,
EG Balsa Armor PCP, EG Balsa Armor PCPG, EG Balsa Armor UC, EG Balsa Armor UCP, EG Balsa Armor UCPG
EG Balsa Rigid Panels including EG Balsa Rigid Panels including EG Balsa GR, EG Balsa GRP,
EG Balsa GRS, EG Balsa
GRPG, EG Balsa IR, EG Balsa IRP, EG Balsa IRPG, EG Balsa LR, EG Balsa LRP, EG Balsa LRPG, EG Balsa PR, EG Balsa PRP,
EG Balsa PRPG, EG Balsa UR, EG Balsa URP, EG Balsa URPG, EG Balsa URSC, EG Balsa FS, EG Balsa Armor
GR, EG Balsa
Armor GRP, EG Balsa Armor GRPG, EG Balsa Armor LR, EG Balsa Armor LRP, EG Balsa Armor LRPG, EG Balsa Armor PR,
EG Balsa Armor PRP, EG Balsa Armor PRPG, EG Balsa Armor UR, EG Balsa Armor URP, EG Balsa Armor URPG
Product Identification Rigid, Scored, Scrimmed, Perforated, or
Coated Balsa Wood Panels
Use of Product Core material used in sandwich construction
Manufacturer/Converter I Core Composites, LLC
Physical Location 802 23rd Street S.W., Cullman, AL 35055 USA
Phone (256) 739 6627
Fax (256) 739 4334
General This product is not hazardous and poses no risk to public health or the environment if used as intended.
When grinding, sanding or
sawing, a fine dust will be produced.
Description
Continuous filament E Glass and Ethylene Vinyl Acetate non hazardous above minimum concentrations
Note: cutting, milling, routing, sanding or otherwise abrading this material may render airborne components subject
to PEL TWA = 15mg/m3.
Clothes Contact Unnecessary
Eye Contact flush eye, upper lid and lower lid with
water; seek medical attention if irritation persists
Skin Contact
Flush with water or wash with soap and water, do not blow. If molten EVA comes in contact with skin, do not pull
from skin, but cool with water.
Inhalation of Dust
evacuate individual to clear air area, if difficulty in breathing persists, administer oxygen, if
breathing stops or
asphyxia is apparent, administer CPR and call for emergency assistance. Keep individual warm and quite.
Inhalation of Gas in the Event of FireMove to fresh air and consult physician.
Ingestion drink water or, if large quantities have been ingested, seek medical attention.
Extinguishing Media Unrestricted carbon dioxide, extinguishing powder, foam & water
Special Firefighting Exposure Do not breathe. Emits toxic fumes
under fire conditions like carbon dioxide and carbon monoxide.
Special Firefighting Equipment Wear self contained breathing apparatus.
Saw dust
balsa saw dust is explosive in certain concentration in the air. Use dust absorbing system which has spark detector
and automatic CO2 extinguishing system.
Personal Protections Unnecessary
Environment Procedure Unnecessary
Clean Up Method Recover mechanically and dispose of according to applicable regulations.
I-Core Composites, LLC
802 23rd Street SW
Cullman, AL 35055
Ph (256) 739 6627
Fx (256) 739 4334
1
Safety Data Sheet
7 HANDLING AND STORAGE
None
8 EXPOSURE CONTROLS / PERSONAL PROTECTION
9 PHYSICAL AND CHEMICAL PROPERTIES
Water Solubility (20 C)
Boiling Point: N/A
10 STABILITY AND REACTIVITY
11 TOXICOLOGICAL INFORMATION
12 ECOLOGICAL INFORMATION
13 DISPOSAL CONSIDERATIONS
14 TRANSPORT INFORMATION
15 REGULATORY INFORMATION
16 OTHER INFORMATION
May 30, 2018
I-Core Composites, Chris Gattiker
Safe Handling Design all working procedures principally to avoid inhalation of dust and eye contact.
Storage
Product is combustible wood and fiberglass and should be stored in cool, dry location away from open flame, heat
sources or other means of
ignition.
Separation of Incompatible Products
Grinding, Sanding & Sawing
Use of a dust/mist respirator approved by NIOSH/MSMA (TC 21C 132) is recommended whenever use of product
results in creation of dust.
Conditions to Avoid Avoid exposure to flames.
Exposure Limits Not applicable
Appearance: wood end grain Odor: None Explosive Properties: None
Density: 80 250 kg/m Melting Point: N/A Lower Explosion Limit: None
Color: white clear brown Ignition
temp: > 200 C Upper Explosion Limit: None
General Information Under normal conditions, product is stable.
Hazardous Decomposition Products No decomposition if used as intended.
General
When used and handled according to specification, the product does not have any harmful effects according to our
experience and knowledge.
Contact with Skin No known allergic reactions. Dust may cause irritation on sensitive
skin.
Eye Contact Dust may cause irritation.
Inhalation Dust may cause irritation of the respiratory tract.
Water Product is not water soluble and has no known effects on ground water.
This product is not a “Hazardous Chemical”.
Last revision
by
This Safety Data Sheet cancels and replaces any previous edition. The data in this safety data sheet describes
the safety requirements of our product and may not be
considered to guaranteeing any product properties. The data in this safety data sheet correspond to our current level of knowledge. We recommend the sharing of
this information with other potential customers and final users. The information reported is based on
available knowledge on safety precautions of the product at
issue date. I Core Composites, LLC does not accept responsibility for workers’ behaviors that are non conforming to the contents of this document. We have no
knowledge of or control over the working conditions. The users are directly responsible for both their
industrial hygiene and their waste disposal.
Degradability Product degrades biologically.
Product Disposal
Balsa dust does not contain any hazardous substances. However, as stated above, dust inhalation, or collection of
dust on floors may cause injury or a hazardous condition to exist.
Use of brooms, vacuums and dust removal systems are recommended. A shop
vacuum is a useful tool for dust and
debris removal from floors and work areas.
User of product should review local, state, and federal regulations concerning health and pollution disposal
procedures to assure its compliance with disposal.
Be aware of high concentration of balsa wood dust in the air => explosion
risk and respiratory problems.
Transportation Product is not classified for any kind of transportation regulation.
I-Core Composites, LLC
802 23rd Street SW
Cullman, AL 35055
Ph (256) 739 6627
Fx (256) 739 4334
2
by | Sep 27, 2025
1 PRODUCT AND COMPANY IDENTIFICATION
2 HAZARDS IDENTIFICATION
3 COMPOSITION INFORMATION ON INGREDIENTS
4FIRST AID MEASURES
5 FIRE HAZARD
6 ACCIDENTAL RELEASE MEASURES
Safety Data Sheet
Product Name
EG Balsa Contourable Panels including EG Balsa GC, EG Balsa GCP, EG Balsa GCPG, EG Balsa GPGS, EG Balsa GPS, EG
Balsa GFX, EG Balsa GFXP, EG Balsa IC, EG Balsa ICP, EG Balsa LC, EG Balsa LCP, EG Balsa LCPG, EG Balsa LPGS, EG Balsa
PC, EG Balsa PCP,
EG Balsa PCPG, EG Balsa UC, EG Balsa UCP, EG Balsa UCPG, EG Balsa Armor GC, EG Balsa Armor GCG,
EG Balsa Armor GSC, EG Balsa Armor GCP, EG Balsa Armor GCPG, EG Balsa Armor GPGS, EG Balsa Armor GFX, EG Balsa
Armor GFXP, EG Balsa Armor LC, EG Balsa
Armor LCP, EG Balsa Armor LCPG, EG Balsa Armor LPGS, EG Balsa Armor PC,
EG Balsa Armor PCP, EG Balsa Armor PCPG, EG Balsa Armor UC, EG Balsa Armor UCP, EG Balsa Armor UCPG
EG Balsa Rigid Panels including EG Balsa Rigid Panels including EG Balsa GR, EG Balsa GRP,
EG Balsa GRS, EG Balsa
GRPG, EG Balsa IR, EG Balsa IRP, EG Balsa IRPG, EG Balsa LR, EG Balsa LRP, EG Balsa LRPG, EG Balsa PR, EG Balsa PRP,
EG Balsa PRPG, EG Balsa UR, EG Balsa URP, EG Balsa URPG, EG Balsa URSC, EG Balsa FS, EG Balsa Armor
GR, EG Balsa
Armor GRP, EG Balsa Armor GRPG, EG Balsa Armor LR, EG Balsa Armor LRP, EG Balsa Armor LRPG, EG Balsa Armor PR,
EG Balsa Armor PRP, EG Balsa Armor PRPG, EG Balsa Armor UR, EG Balsa Armor URP, EG Balsa Armor URPG
Product Identification Rigid, Scored, Scrimmed, Perforated, or
Coated Balsa Wood Panels
Use of Product Core material used in sandwich construction
Manufacturer/Converter I Core Composites, LLC
Physical Location 802 23rd Street S.W., Cullman, AL 35055 USA
Phone (256) 739 6627
Fax (256) 739 4334
General This product is not hazardous and poses no risk to public health or the environment if used as intended.
When grinding, sanding or
sawing, a fine dust will be produced.
Description
Continuous filament E Glass and Ethylene Vinyl Acetate non hazardous above minimum concentrations
Note: cutting, milling, routing, sanding or otherwise abrading this material may render airborne components subject
to PEL TWA = 15mg/m3.
Clothes Contact Unnecessary
Eye Contact flush eye, upper lid and lower lid with
water; seek medical attention if irritation persists
Skin Contact
Flush with water or wash with soap and water, do not blow. If molten EVA comes in contact with skin, do not pull
from skin, but cool with water.
Inhalation of Dust
evacuate individual to clear air area, if difficulty in breathing persists, administer oxygen, if
breathing stops or
asphyxia is apparent, administer CPR and call for emergency assistance. Keep individual warm and quite.
Inhalation of Gas in the Event of FireMove to fresh air and consult physician.
Ingestion drink water or, if large quantities have been ingested, seek medical attention.
Extinguishing Media Unrestricted carbon dioxide, extinguishing powder, foam & water
Special Firefighting Exposure Do not breathe. Emits toxic fumes
under fire conditions like carbon dioxide and carbon monoxide.
Special Firefighting Equipment Wear self contained breathing apparatus.
Saw dust
balsa saw dust is explosive in certain concentration in the air. Use dust absorbing system which has spark detector
and automatic CO2 extinguishing system.
Personal Protections Unnecessary
Environment Procedure Unnecessary
Clean Up Method Recover mechanically and dispose of according to applicable regulations.
I-Core Composites, LLC
802 23rd Street SW
Cullman, AL 35055
Ph (256) 739 6627
Fx (256) 739 4334
1
Safety Data Sheet
7 HANDLING AND STORAGE
None
8 EXPOSURE CONTROLS / PERSONAL PROTECTION
9 PHYSICAL AND CHEMICAL PROPERTIES
Water Solubility (20 C)
Boiling Point: N/A
10 STABILITY AND REACTIVITY
11 TOXICOLOGICAL INFORMATION
12 ECOLOGICAL INFORMATION
13 DISPOSAL CONSIDERATIONS
14 TRANSPORT INFORMATION
15 REGULATORY INFORMATION
16 OTHER INFORMATION
May 30, 2018
I-Core Composites, Chris Gattiker
Safe Handling Design all working procedures principally to avoid inhalation of dust and eye contact.
Storage
Product is combustible wood and fiberglass and should be stored in cool, dry location away from open flame, heat
sources or other means of
ignition.
Separation of Incompatible Products
Grinding, Sanding & Sawing
Use of a dust/mist respirator approved by NIOSH/MSMA (TC 21C 132) is recommended whenever use of product
results in creation of dust.
Conditions to Avoid Avoid exposure to flames.
Exposure Limits Not applicable
Appearance: wood end grain Odor: None Explosive Properties: None
Density: 80 250 kg/m Melting Point: N/A Lower Explosion Limit: None
Color: white clear brown Ignition
temp: > 200 C Upper Explosion Limit: None
General Information Under normal conditions, product is stable.
Hazardous Decomposition Products No decomposition if used as intended.
General
When used and handled according to specification, the product does not have any harmful effects according to our
experience and knowledge.
Contact with Skin No known allergic reactions. Dust may cause irritation on sensitive
skin.
Eye Contact Dust may cause irritation.
Inhalation Dust may cause irritation of the respiratory tract.
Water Product is not water soluble and has no known effects on ground water.
This product is not a “Hazardous Chemical”.
Last revision
by
This Safety Data Sheet cancels and replaces any previous edition. The data in this safety data sheet describes
the safety requirements of our product and may not be
considered to guaranteeing any product properties. The data in this safety data sheet correspond to our current level of knowledge. We recommend the sharing of
this information with other potential customers and final users. The information reported is based on
available knowledge on safety precautions of the product at
issue date. I Core Composites, LLC does not accept responsibility for workers’ behaviors that are non conforming to the contents of this document. We have no
knowledge of or control over the working conditions. The users are directly responsible for both their
industrial hygiene and their waste disposal.
Degradability Product degrades biologically.
Product Disposal
Balsa dust does not contain any hazardous substances. However, as stated above, dust inhalation, or collection of
dust on floors may cause injury or a hazardous condition to exist.
Use of brooms, vacuums and dust removal systems are recommended. A shop
vacuum is a useful tool for dust and
debris removal from floors and work areas.
User of product should review local, state, and federal regulations concerning health and pollution disposal
procedures to assure its compliance with disposal.
Be aware of high concentration of balsa wood dust in the air => explosion
risk and respiratory problems.
Transportation Product is not classified for any kind of transportation regulation.
I-Core Composites, LLC
802 23rd Street SW
Cullman, AL 35055
Ph (256) 739 6627
Fx (256) 739 4334
2
by | Sep 27, 2025
1 PRODUCT AND COMPANY IDENTIFICATION
2 HAZARDS IDENTIFICATION
3 COMPOSITION INFORMATION ON INGREDIENTS
4FIRST AID MEASURES
5 FIRE HAZARD
6 ACCIDENTAL RELEASE MEASURES
Safety Data Sheet
Product Name
EG Balsa Contourable Panels including EG Balsa GC, EG Balsa GCP, EG Balsa GCPG, EG Balsa GPGS, EG Balsa GPS, EG
Balsa GFX, EG Balsa GFXP, EG Balsa IC, EG Balsa ICP, EG Balsa LC, EG Balsa LCP, EG Balsa LCPG, EG Balsa LPGS, EG Balsa
PC, EG Balsa PCP,
EG Balsa PCPG, EG Balsa UC, EG Balsa UCP, EG Balsa UCPG, EG Balsa Armor GC, EG Balsa Armor GCG,
EG Balsa Armor GSC, EG Balsa Armor GCP, EG Balsa Armor GCPG, EG Balsa Armor GPGS, EG Balsa Armor GFX, EG Balsa
Armor GFXP, EG Balsa Armor LC, EG Balsa
Armor LCP, EG Balsa Armor LCPG, EG Balsa Armor LPGS, EG Balsa Armor PC,
EG Balsa Armor PCP, EG Balsa Armor PCPG, EG Balsa Armor UC, EG Balsa Armor UCP, EG Balsa Armor UCPG
EG Balsa Rigid Panels including EG Balsa Rigid Panels including EG Balsa GR, EG Balsa GRP,
EG Balsa GRS, EG Balsa
GRPG, EG Balsa IR, EG Balsa IRP, EG Balsa IRPG, EG Balsa LR, EG Balsa LRP, EG Balsa LRPG, EG Balsa PR, EG Balsa PRP,
EG Balsa PRPG, EG Balsa UR, EG Balsa URP, EG Balsa URPG, EG Balsa URSC, EG Balsa FS, EG Balsa Armor
GR, EG Balsa
Armor GRP, EG Balsa Armor GRPG, EG Balsa Armor LR, EG Balsa Armor LRP, EG Balsa Armor LRPG, EG Balsa Armor PR,
EG Balsa Armor PRP, EG Balsa Armor PRPG, EG Balsa Armor UR, EG Balsa Armor URP, EG Balsa Armor URPG
Product Identification Rigid, Scored, Scrimmed, Perforated, or
Coated Balsa Wood Panels
Use of Product Core material used in sandwich construction
Manufacturer/Converter I Core Composites, LLC
Physical Location 802 23rd Street S.W., Cullman, AL 35055 USA
Phone (256) 739 6627
Fax (256) 739 4334
General This product is not hazardous and poses no risk to public health or the environment if used as intended.
When grinding, sanding or
sawing, a fine dust will be produced.
Description
Continuous filament E Glass and Ethylene Vinyl Acetate non hazardous above minimum concentrations
Note: cutting, milling, routing, sanding or otherwise abrading this material may render airborne components subject
to PEL TWA = 15mg/m3.
Clothes Contact Unnecessary
Eye Contact flush eye, upper lid and lower lid with
water; seek medical attention if irritation persists
Skin Contact
Flush with water or wash with soap and water, do not blow. If molten EVA comes in contact with skin, do not pull
from skin, but cool with water.
Inhalation of Dust
evacuate individual to clear air area, if difficulty in breathing persists, administer oxygen, if
breathing stops or
asphyxia is apparent, administer CPR and call for emergency assistance. Keep individual warm and quite.
Inhalation of Gas in the Event of FireMove to fresh air and consult physician.
Ingestion drink water or, if large quantities have been ingested, seek medical attention.
Extinguishing Media Unrestricted carbon dioxide, extinguishing powder, foam & water
Special Firefighting Exposure Do not breathe. Emits toxic fumes
under fire conditions like carbon dioxide and carbon monoxide.
Special Firefighting Equipment Wear self contained breathing apparatus.
Saw dust
balsa saw dust is explosive in certain concentration in the air. Use dust absorbing system which has spark detector
and automatic CO2 extinguishing system.
Personal Protections Unnecessary
Environment Procedure Unnecessary
Clean Up Method Recover mechanically and dispose of according to applicable regulations.
I-Core Composites, LLC
802 23rd Street SW
Cullman, AL 35055
Ph (256) 739 6627
Fx (256) 739 4334
1
Safety Data Sheet
7 HANDLING AND STORAGE
None
8 EXPOSURE CONTROLS / PERSONAL PROTECTION
9 PHYSICAL AND CHEMICAL PROPERTIES
Water Solubility (20 C)
Boiling Point: N/A
10 STABILITY AND REACTIVITY
11 TOXICOLOGICAL INFORMATION
12 ECOLOGICAL INFORMATION
13 DISPOSAL CONSIDERATIONS
14 TRANSPORT INFORMATION
15 REGULATORY INFORMATION
16 OTHER INFORMATION
May 30, 2018
I-Core Composites, Chris Gattiker
Safe Handling Design all working procedures principally to avoid inhalation of dust and eye contact.
Storage
Product is combustible wood and fiberglass and should be stored in cool, dry location away from open flame, heat
sources or other means of
ignition.
Separation of Incompatible Products
Grinding, Sanding & Sawing
Use of a dust/mist respirator approved by NIOSH/MSMA (TC 21C 132) is recommended whenever use of product
results in creation of dust.
Conditions to Avoid Avoid exposure to flames.
Exposure Limits Not applicable
Appearance: wood end grain Odor: None Explosive Properties: None
Density: 80 250 kg/m Melting Point: N/A Lower Explosion Limit: None
Color: white clear brown Ignition
temp: > 200 C Upper Explosion Limit: None
General Information Under normal conditions, product is stable.
Hazardous Decomposition Products No decomposition if used as intended.
General
When used and handled according to specification, the product does not have any harmful effects according to our
experience and knowledge.
Contact with Skin No known allergic reactions. Dust may cause irritation on sensitive
skin.
Eye Contact Dust may cause irritation.
Inhalation Dust may cause irritation of the respiratory tract.
Water Product is not water soluble and has no known effects on ground water.
This product is not a “Hazardous Chemical”.
Last revision
by
This Safety Data Sheet cancels and replaces any previous edition. The data in this safety data sheet describes
the safety requirements of our product and may not be
considered to guaranteeing any product properties. The data in this safety data sheet correspond to our current level of knowledge. We recommend the sharing of
this information with other potential customers and final users. The information reported is based on
available knowledge on safety precautions of the product at
issue date. I Core Composites, LLC does not accept responsibility for workers’ behaviors that are non conforming to the contents of this document. We have no
knowledge of or control over the working conditions. The users are directly responsible for both their
industrial hygiene and their waste disposal.
Degradability Product degrades biologically.
Product Disposal
Balsa dust does not contain any hazardous substances. However, as stated above, dust inhalation, or collection of
dust on floors may cause injury or a hazardous condition to exist.
Use of brooms, vacuums and dust removal systems are recommended. A shop
vacuum is a useful tool for dust and
debris removal from floors and work areas.
User of product should review local, state, and federal regulations concerning health and pollution disposal
procedures to assure its compliance with disposal.
Be aware of high concentration of balsa wood dust in the air => explosion
risk and respiratory problems.
Transportation Product is not classified for any kind of transportation regulation.
I-Core Composites, LLC
802 23rd Street SW
Cullman, AL 35055
Ph (256) 739 6627
Fx (256) 739 4334
2
by | Sep 27, 2025
1PRODUCT AND COMPANY IDENTIFICATION
2HAZARDS IDENTIFICATION
3COMPOSITION INFORMATION ON INGREDIENTS
4FIRST AID MEASURES
5FIRE HAZARD
6ACCIDENTAL RELEASE MEASURES
Safety Data Sheet
Product Name
EG Balsa Contourable Panels including EG Balsa GC, EG Balsa GCP, EG Balsa GCPG, EG Balsa GPGS, EG Balsa GPS, EG
Balsa GFX, EG Balsa GFXP, EG Balsa IC, EG Balsa ICP, EG Balsa LC, EG Balsa LCP, EG Balsa LCPG, EG Balsa LPGS, EG Balsa PC,
EG Balsa PCP, EG Balsa PCPG, EG Balsa UC, EG Balsa UCP, EG Balsa UCPG, EG Balsa Armor GC, EG Balsa Armor GCG, EG
Balsa Armor GSC, EG Balsa Armor GCP, EG Balsa Armor GCPG, EG Balsa Armor GPGS, EG Balsa Armor GFX, EG Balsa Armor
GFXP, EG Balsa Armor LC, EG Balsa Armor LCP, EG Balsa Armor LCPG, EG Balsa Armor LPGS, EG Balsa Armor PC, EG Balsa
Armor PCP, EG Balsa Armor PCPG, EG Balsa Armor UC, EG Balsa Armor UCP, EG Balsa Armor UCPG
EG Balsa Rigid Panels including EG Balsa Rigid Panels including EG Balsa GR, EG Balsa GRP, EG Balsa GRS, EG Balsa GRPG,
EG Balsa IR, EG Balsa IRP, EG Balsa IRPG, EG Balsa LR, EG Balsa LRP, EG Balsa LRPG, EG Balsa PR, EG Balsa PRP, EG Balsa
PRPG, EG Balsa UR, EG Balsa URP, EG Balsa URPG, EG Balsa URSC, EG Balsa FS, EG Balsa Armor GR, EG Balsa Armor GRP,
EG Balsa Armor GRPG, EG Balsa Armor LR, EG Balsa Armor LRP, EG Balsa Armor LRPG, EG Balsa Armor PR, EG Balsa Armor
PRP, EG Balsa Armor PRPG, EG Balsa Armor UR, EG Balsa Armor URP, EG Balsa Armor URPG, LR Flat Grain
Product Identification Rigid, Scored, Scrimmed, Perforated, flat grain or Coated Balsa Wood Panels
Use of Product Core material used in sandwich construction
Manufacturer/Converter I-Core Composites, LLC
Physical Location 802 23rd Street S.W., Cullman, AL 35055 – USA
Phone (256) 739-6627
Fax (256) 739-4334
General This product is not hazardous and poses no risk to public health or the environment if used as intended.
When grinding, sanding or sawing, a fine dust will be produced.
Description
Continuous filament E Glass and Ethylene Vinyl Acetate non-hazardous above minimum concentrations
Note: cutting, milling, routing, sanding or otherwise abrading this material may render airborne components subject to
PEL TWA = 15mg/m3.
Clothes Contact Unnecessary
Eye Contact flush eye, upper lid and lower lid with water; seek medical attention if irritation persists
Skin Contact
Flush with water or wash with soap and water, do not blow. If molten EVA comes in contact with skin, do not pull from
skin, but cool with water.
Inhalation of Dust
evacuate individual to clear air area, if difficulty in breathing persists, administer oxygen, if breathing stops or asphyxia is
apparent, administer CPR and call for emergency assistance. Keep individual warm and quite.
Inhalation of Gas in the Event of FireMove to fresh air and consult physician.
Ingestion drink water or, if large quantities have been ingested, seek medical attention.
Extinguishing Media Unrestricted – carbon dioxide, extinguishing powder, foam & water
Special Firefighting Exposure Do not breathe. Emits toxic fumes under fire conditions like carbon dioxide and carbon monoxide.
Special Firefighting Equipment Wear self-contained breathing apparatus.
Saw dust
balsa saw dust is explosive in certain concentration in the air. Use dust absorbing system which has spark detector and
automatic CO2 extinguishing system.
Personal Protections Unnecessary
Environment Procedure Unnecessary
Clean Up Method Recover mechanically and dispose of according to applicable regulations.
I-Core Composites, LLC
802 23rd Street SW
Cullman, AL 35055
Ph (256) 739-6627
Fx (256) 739-4334 1
Safety Data Sheet
7HANDLING AND STORAGE
None
8EXPOSURE CONTROLS / PERSONAL PROTECTION
9PHYSICAL AND CHEMICAL PROPERTIES
Water Solubility (20 C)
Boiling Point: N/A
10STABILITY AND REACTIVITY
11TOXICOLOGICAL INFORMATION
12ECOLOGICAL INFORMATION
13DISPOSAL CONSIDERATIONS
14TRANSPORT INFORMATION
15REGULATORY INFORMATION
16OTHER INFORMATION
May 24, 2022
I-Core Composites, Chris Gattiker
Safe Handling Design all working procedures principally to avoid inhalation of dust and eye contact.
Storage
Product is combustible wood and fiberglass and should be stored in cool, dry location away from open flame, heat
sources or other means of ignition.
Separation of Incompatible Products
Grinding, Sanding & Sawing
Use of a dust/mist respirator approved by NIOSH/MSMA (TC-21C-132) is recommended whenever use of product results
in creation of dust.
Conditions to Avoid Avoid exposure to flames.
Exposure Limits Not applicable
Appearance: wood end grain Odor: None Explosive Properties: None
Density: 80-250 kg/m Melting Point: N/A Lower Explosion Limit: None
Color: white – clear brown Ignition temp: > 200 C Upper Explosion Limit: None
General Information Under normal conditions, product is stable.
Hazardous Decomposition Products No decomposition if used as intended.
General
When used and handled according to specification, the product does not have any harmful effects according to our
experience and knowledge.
Contact with Skin No known allergic reactions. Dust may cause irritation on sensitive skin.
Eye Contact Dust may cause irritation.
Inhalation Dust may cause irritation of the respiratory tract.
Water Product is not water soluble and has no known effects on ground water.
This product is not a “Hazardous Chemical”.
Last revision
by
This Safety Data Sheet cancels and replaces any previous edition. The data in this safety data sheet describes the safety requirements of our product and may not be
considered to guaranteeing any product properties. The data in this safety data sheet correspond to our current level of knowledge. We recommend the sharing of this
information with other potential customers and final users. The information reported is based on available knowledge on safety precautions of the product at issue
date. I-Core Composites, LLC does not accept responsibility for workers’ behaviors that are non-conforming to the contents of this document. We have no knowledge of
or control over the working conditions. The users are directly responsible for both their industrial hygiene and their waste disposal.
Degradability Product degrades biologically.
Product Disposal
Balsa dust does not contain any hazardous substances. However, as stated above, dust inhalation, or collection of dust on
floors may cause injury or a hazardous condition to exist.
Use of brooms, vacuums and dust removal systems are recommended. A shop vacuum is a useful tool for dust and debris
removal from floors and work areas.
User of product should review local, state, and federal regulations concerning health and pollution disposal procedures
to assure its compliance with disposal.
Be aware of high concentration of balsa wood dust in the air => explosion risk and respiratory problems.
Transportation Product is not classified for any kind of transportation regulation.
I-Core Composites, LLC
802 23rd Street SW
Cullman, AL 35055
Ph (256) 739-6627
Fx (256) 739-4334 2
by | Sep 27, 2025
1PRODUCT AND COMPANY IDENTIFICATION
2HAZARDS IDENTIFICATION
3COMPOSITION INFORMATION ON INGREDIENTS
4FIRST AID MEASURES
5FIRE HAZARD
6ACCIDENTAL RELEASE MEASURES
Environment Procedure Unnecessary
Clean Up Method Recover mechanically and dispose of according to applicable regulations.
Special Firefighting Equipment Wear self-contained breathing apparatus.
Saw dust
balsa saw dust is explosive in certain concentration in the air. Use dust absorbing system which has spark detector and
automatic CO2 extinguishing system.
Personal Protections Unnecessary
Ingestion drink water or, if large quantities have been ingested, seek medical attention.
Extinguishing Media Unrestricted – carbon dioxide, extinguishing powder, foam & water
Special Firefighting Exposure Do not breathe. Emits toxic fumes under fire conditions like carbon dioxide and carbon monoxide.
Skin Contact
Flush with water or wash with soap and water, do not blow. If molten EVA comes in contact with skin, do not pull from
skin, but cool with water.
Inhalation of Dust
evacuate individual to clear air area, if difficulty in breathing persists, administer oxygen, if breathing stops or asphyxia is
apparent, administer CPR and call for emergency assistance. Keep individual warm and quite.
Inhalation of Gas in the Event of FireMove to fresh air and consult physician.
Description
Continuous filament E Glass and Ethylene Vinyl Acetate non-hazardous above minimum concentrations
Note: cutting, milling, routing, sanding or otherwise abrading this material may render airborne components subject to
PEL TWA = 15mg/m3.
Clothes Contact Unnecessary
Eye Contact flush eye, upper lid and lower lid with water; seek medical attention if irritation persists
When grinding, sanding or sawing, a fine dust will be produced.
Phone (256) 739-6627
Fax (256) 739-4334
General This product is not hazardous and poses no risk to public health or the environment if used as intended.
Use of Product Core material used in sandwich construction
Manufacturer/Converter I-Core Composites, LLC
Physical Location 802 23rd Street S.W., Cullman, AL 35055 – USA
Safety Data Sheet
Product Name
EG Balsa Contourable Panels including EG Balsa GC, EG Balsa GCP, EG Balsa GCPG, EG Balsa GPGS, EG Balsa GPS, EG
Balsa GFX, EG Balsa GFXP, EG Balsa IC, EG Balsa ICP, EG Balsa LC, EG Balsa LCP, EG Balsa LCPG, EG Balsa LPGS, EG Balsa PC,
EG Balsa PCP, EG Balsa PCPG, EG Balsa UC, EG Balsa UCP, EG Balsa UCPG, EG Balsa Armor GC, EG Balsa Armor GCG, EG
Balsa Armor GSC, EG Balsa Armor GCP, EG Balsa Armor GCPG, EG Balsa Armor GPGS, EG Balsa Armor GFX, EG Balsa Armor
GFXP, EG Balsa Armor LC, EG Balsa Armor LCP, EG Balsa Armor LCPG, EG Balsa Armor LPGS, EG Balsa Armor PC, EG Balsa
Armor PCP, EG Balsa Armor PCPG, EG Balsa Armor UC, EG Balsa Armor UCP, EG Balsa Armor UCPG
EG Balsa Rigid Panels including EG Balsa Rigid Panels including EG Balsa GR, EG Balsa GRP, EG Balsa GRS, EG Balsa GRPG,
EG Balsa IR, EG Balsa IRP, EG Balsa IRPG, EG Balsa LR, EG Balsa LRP, EG Balsa LRPG, EG Balsa PR, EG Balsa PRP, EG Balsa
PRPG, EG Balsa UR, EG Balsa URP, EG Balsa URPG, EG Balsa URSC, EG Balsa FS, EG Balsa Armor GR, EG Balsa Armor GRP,
EG Balsa Armor GRPG, EG Balsa Armor LR, EG Balsa Armor LRP, EG Balsa Armor LRPG, EG Balsa Armor PR, EG Balsa Armor
PRP, EG Balsa Armor PRPG, EG Balsa Armor UR, EG Balsa Armor URP, EG Balsa Armor URPG, LR Flat Grain
Product Identification Rigid, Scored, Scrimmed, Perforated, flat grain or Coated Balsa Wood Panels
I-Core Composites, LLC
802 23rd Street SW
Cullman, AL 35055
Ph (256) 739-6627
Fx (256) 739-4334 1
Safety Data Sheet
7HANDLING AND STORAGE
None
8EXPOSURE CONTROLS / PERSONAL PROTECTION
9PHYSICAL AND CHEMICAL PROPERTIES
Water Solubility (20 C)
Boiling Point: N/A
10STABILITY AND REACTIVITY
11TOXICOLOGICAL INFORMATION
12ECOLOGICAL INFORMATION
13DISPOSAL CONSIDERATIONS
14TRANSPORT INFORMATION
15REGULATORY INFORMATION
16OTHER INFORMATION
October 10, 2024
I-Core Composites, Chris Gattiker
This product is not a “Hazardous Chemical”.
Last revision
by
This Safety Data Sheet cancels and replaces any previous edition. The data in this safety data sheet describes the safety requirements of our product and may not be
considered to guaranteeing any product properties. The data in this safety data sheet correspond to our current level of knowledge. We recommend the sharing of this
information with other potential customers and final users. The information reported is based on available knowledge on safety precautions of the product at issue
date. I-Core Composites, LLC does not accept responsibility for workers’ behaviors that are non-conforming to the contents of this document. We have no knowledge of
or control over the working conditions. The users are directly responsible for both their industrial hygiene and their waste disposal.
Degradability Product degrades biologically.
Product Disposal
Balsa dust does not contain any hazardous substances. However, as stated above, dust inhalation, or collection of dust on
floors may cause injury or a hazardous condition to exist.
Use of brooms, vacuums and dust removal systems are recommended. A shop vacuum is a useful tool for dust and debris
removal from floors and work areas.
User of product should review local, state, and federal regulations concerning health and pollution disposal procedures
to assure its compliance with disposal.
Be aware of high concentration of balsa wood dust in the air => explosion risk and respiratory problems.
Transportation Product is not classified for any kind of transportation regulation.
Eye Contact Dust may cause irritation.
Inhalation Dust may cause irritation of the respiratory tract.
Water Product is not water soluble and has no known effects on ground water.
Hazardous Decomposition Products No decomposition if used as intended.
General
When used and handled according to specification, the product does not have any harmful effects according to our
experience and knowledge.
Contact with Skin No known allergic reactions. Dust may cause irritation on sensitive skin.
Conditions to Avoid Avoid exposure to flames.
Exposure Limits Not applicable
Appearance: wood end grain Odor: None Explosive Properties: None
Density: 80-250 kg/m Melting Point: N/A Lower Explosion Limit: None
Color: white – clear brown Ignition temp: > 200 C Upper Explosion Limit: None
General Information Under normal conditions, product is stable.
Storage
Product is combustible wood and fiberglass and should be stored in cool, dry location away from open flame, heat
sources or other means of ignition.
Separation of Incompatible Products
Grinding, Sanding & Sawing
Use of a dust/mist respirator approved by NIOSH/MSMA (TC-21C-132) is recommended whenever use of product results
in creation of dust.
Safe Handling Design all working procedures principally to avoid inhalation of dust and eye contact.
I-Core Composites, LLC
802 23rd Street SW
Cullman, AL 35055
Ph (256) 739-6627
Fx (256) 739-4334 2
by | Sep 27, 2025
1PRODUCT AND COMPANY IDENTIFICATION
2HAZARDS IDENTIFICATION
3COMPOSITION INFORMATION ON INGREDIENTS
4FIRST AID MEASURES
5FIRE HAZARD
6ACCIDENTAL RELEASE MEASURES
Environment Procedure Unnecessary
Clean Up Method Recover mechanically and dispose of according to applicable regulations.
Special Firefighting Equipment Wear self-contained breathing apparatus.
Saw dust
balsa saw dust is explosive in certain concentration in the air. Use dust absorbing system which has spark detector and
automatic CO2 extinguishing system.
Personal Protections Unnecessary
Ingestion drink water or, if large quantities have been ingested, seek medical attention.
Extinguishing Media Unrestricted – carbon dioxide, extinguishing powder, foam & water
Special Firefighting Exposure Do not breathe. Emits toxic fumes under fire conditions like carbon dioxide and carbon monoxide.
Skin Contact
Flush with water or wash with soap and water, do not blow. If molten EVA comes in contact with skin, do not pull from
skin, but cool with water.
Inhalation of Dust
evacuate individual to clear air area, if difficulty in breathing persists, administer oxygen, if breathing stops or asphyxia is
apparent, administer CPR and call for emergency assistance. Keep individual warm and quite.
Inhalation of Gas in the Event of FireMove to fresh air and consult physician.
Description
Continuous filament E Glass and Ethylene Vinyl Acetate non-hazardous above minimum concentrations
Note: cutting, milling, routing, sanding or otherwise abrading this material may render airborne components subject to
PEL TWA = 15mg/m3.
Clothes Contact Unnecessary
Eye Contact flush eye, upper lid and lower lid with water; seek medical attention if irritation persists
When grinding, sanding or sawing, a fine dust will be produced.
Phone (256) 739-6627
Fax (256) 739-4334
General This product is not hazardous and poses no risk to public health or the environment if used as intended.
Use of Product Core material used in sandwich construction
Manufacturer/Converter I-Core Composites, LLC
Physical Location 802 23rd Street S.W., Cullman, AL 35055 – USA
Safety Data Sheet
Product Name
EG Balsa Contourable Panels including EG Balsa GC, EG Balsa GCP, EG Balsa GCPG, EG Balsa GPGS, EG Balsa GPS, EG
Balsa GFX, EG Balsa GFXP, EG Balsa IC, EG Balsa ICP, EG Balsa LC, EG Balsa LCP, EG Balsa LCPG, EG Balsa LPGS, EG Balsa
PC, EG Balsa PCP, EG Balsa PCPG, EG Balsa UC, EG Balsa UCP, EG Balsa UCPG, EG Balsa Armor GC, EG Balsa Armor GCG,
EG Balsa Armor GSC, EG Balsa Armor GCP, EG Balsa Armor GCPG, EG Balsa Armor GPGS, EG Balsa Armor GFX, EG Balsa
Armor GFXP, EG Balsa Armor LC, EG Balsa Armor LCP, EG Balsa Armor LCPG, EG Balsa Armor LPGS, EG Balsa Armor PC, EG
Balsa Armor PCP, EG Balsa Armor PCPG, EG Balsa Armor UC, EG Balsa Armor UCP, EG Balsa Armor UCPG
EG Balsa Rigid Panels including EG Balsa Rigid
Panels including EG Balsa GR, EG Balsa GRP, EG Balsa GRS, EG Balsa GRPG, EG Balsa IR, EG Balsa IRP, EG Balsa IRPG, EG
Balsa LR, EG Balsa LRP, EG Balsa LRPG, EG Balsa PR, EG Balsa PRP, EG Balsa PRPG, EG Balsa UR, EG Balsa URP, EG Balsa
URPG, EG Balsa URSC, EG Balsa FS, EG Balsa Armor GR, EG Balsa Armor GRP, EG Balsa Armor GRPG, EG Balsa Armor LR,
EG Balsa Armor LRP, EG Balsa Armor LRPG, EG Balsa Armor PR, EG Balsa Armor PRP, EG Balsa Armor PRPG, EG Balsa
Armor UR, EG Balsa Armor URP, EG Balsa Armor URPG
Product Identification Rigid, Scored, Scrimmed, Perforated, or Coated Balsa Wood Panels
I-Core Composites, LLC
802 23rd Street SW
Cullman, AL 35055
Ph (256) 739-6627
Fx (256) 739-4334 1
Safety Data Sheet
7HANDLING AND STORAGE
None
8EXPOSURE CONTROLS / PERSONAL PROTECTION
9PHYSICAL AND CHEMICAL PROPERTIES
Water Solubility (20 C)
Boiling Point: N/A
10STABILITY AND REACTIVITY
11TOXICOLOGICAL INFORMATION
12ECOLOGICAL INFORMATION
13DISPOSAL CONSIDERATIONS
14TRANSPORT INFORMATION
15REGULATORY INFORMATION
16OTHER INFORMATION
November 1, 2020
I-Core Composites, Chris Gattiker
This product is not a “Hazardous Chemical”.
Last revision
by
This Safety Data Sheet cancels and replaces any previous edition. The data in this safety data sheet describes the safety requirements of our product and may not be
considered to guaranteeing any product properties. The data in this safety data sheet correspond to our current level of knowledge. We recommend the sharing of this
information with other potential customers and final users. The information reported is based on available knowledge on safety precautions of the product at issue
date. I-Core Composites, LLC does not accept responsibility for workers’ behaviors that are non-conforming to the contents of this document. We have no knowledge of
or control over the working conditions. The users are directly responsible for both their industrial hygiene and their waste disposal.
Degradability Product degrades biologically.
Product Disposal
Balsa dust does not contain any hazardous substances. However, as stated above, dust inhalation, or collection of dust
on floors may cause injury or a hazardous condition to exist.
Use of brooms, vacuums and dust removal systems are recommended. A shop vacuum is a useful tool for dust and debris
removal from floors and work areas.
User of product should review local, state, and federal regulations concerning health and pollution disposal procedures
to assure its compliance with disposal.
Be aware of high concentration of balsa wood dust in the air => explosion risk and respiratory problems.
Transportation Product is not classified for any kind of transportation regulation.
Eye Contact Dust may cause irritation.
Inhalation Dust may cause irritation of the respiratory tract.
Water Product is not water soluble and has no known effects on ground water.
Hazardous Decomposition Products No decomposition if used as intended.
General
When used and handled according to specification, the product does not have any harmful effects according to our
experience and knowledge.
Contact with Skin No known allergic reactions. Dust may cause irritation on sensitive skin.
Conditions to Avoid Avoid exposure to flames.
Exposure Limits Not applicable
Appearance: wood end grain Odor: None Explosive Properties: None
Density: 80-250 kg/m Melting Point: N/A Lower Explosion Limit: None
Color: white – clear brown Ignition temp: > 200 C Upper Explosion Limit: None
General Information Under normal conditions, product is stable.
Storage
Product is combustible wood and fiberglass and should be stored in cool, dry location away from open flame, heat
sources or other means of ignition.
Separation of Incompatible Products
Grinding, Sanding & Sawing
Use of a dust/mist respirator approved by NIOSH/MSMA (TC-21C-132) is recommended whenever use of product results
in creation of dust.
Safe Handling Design all working procedures principally to avoid inhalation of dust and eye contact.
I-Core Composites, LLC
802 23rd Street SW
Cullman, AL 35055
Ph (256) 739-6627
Fx (256) 739-4334 2
by | Sep 27, 2025
INDEX
27H80
27H80012P
27H80012PB
27H80025GS
27H80025P
27H80025PA
27H80050GA
27H80050PB
27H80075G
27H80075GS
27H80075PA
27H80100G
27H80100GS
27H80100PA
27H80120GS
27H80150G
27H80150PA
27H80150PL
27H80200P
27H802INPP
27H80375GS
27H80375PB
27H8050GPC
27H8050GSP
27H80625P
27H80DC05A
27H80DC075
27H80DCC03
SAFETY DATA SHEET
Divinycell H HP HM HT Matrix HCP Issue date: 2015-06-01 Revised: 2015-06-01 Revision: 0 Page 1(4)
Tel +1 (972) 228-7600
Fax +1 (972) 228-2667
E-mail: info@us.diabgroup.com
Web Site: www.diabgroup.com
1. IDENTIFICATION
Product: DIVINYCELL H H45, H60, H80, H100, H130
DIVINYCELL HP HP60, HP80, HP100, HP130, HP 160, HP200, HP250
DIVINYCELL HM HM80, HM100, HM130
DIVINYCELL HT HT61, HT81, HT101, HT131
DIVINYCELL MATRIX MATRIX 7-7, MATRIX 10-8, MATRIX 11-9
DIVINYCELL HCP HCP30, HCP50, HCP70, HCP90, HCP100
STRUCTURAL FOAM CORE MATERIAL FOR MFG OF COMPOSITE STRUCTU RES
Supplier: DIAB Americas LP
315 Seahawk Drive
Desoto, TX 75115
Contact: Infotrac
1-800-535-5053
2. HAZARD(S) IDENTIFICATION
The foam material is not hazardous under normal handling and storage conditions. When
exposed to a direct flame, this material will generate acid HCl gas from thermal decomposition.
The primary hazard is dust generation during processing with cutting, sanding and sawing
operations. Dust mask protection should be used when performing these types of operations.
The dust will ignite if given sufficient ignition source and should be processed in a way to avoid
static sparks and accumulation of extra dust in the manufacturing area with good cleaning
practices in the manufacturing areas.
3. COMPOSITION / INFORMATION ON INGRE DIENTS
CHEMICAL NAME CAS NO CONTENT SYMBOLS R-PHRASES
PVC 9002-86-2 30-75 % — —
Aromatic polyurea — 15-50 % — —
Polyamide — 3-10 % — —
These materials are rigid polymeric foams made of alloys of PVC, aromatic polyurea and
polyamide.
4. FIRST-AID MEASURES
SAFETY DATA SHEET
Divinycell H HP HM HT Matrix HCP Issue date: 2015-06-01 Revised: 2015-06-01 Revision: 0 Page 2(4)
Tel +1 (972) 228-7600
Fax +1 (972) 228-2667
E-mail: info@us.diabgroup.com
Web Site: www.diabgroup.com
Inhalation: Fresh air.
Skin contact: No special measures.
Eye contact: By direct contact with shavings or dust, irrigate with flowing water.
Consult medical personnel if irritation persists.
Ingestion: Consult medical personnel if large amounts have been swallowed.
5. FIRE-FIGHTING MEASURES
Oxygen Index > 21% by ASTM D2863
Self Extinguishing by ASTM 1692
Flammable by direct flame only
Hazardous combustion products:
Hydrogen chloride (HCI) and hydrogen cyanide (HCN) can be developed.
Extinguishing media:
Use foam, carbon dioxide, dry chemical, water fog, earth or sand.
Use breathing apparatus against combustion products.
6. ACCIDENTAL RELEASE MEASURES
Spills Not Applicable (Solid Foam form)
7. HANDLING AND STORAGE
Dust can be produced during mechanical process. Use local dust collection system.
Long term storage should be in a cool < 104 F (<40 C) and dry place, away from combustible
material. Avoid exposure to temperatures in excess of 122 F (50 C) during transportation or
short term storage.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Exhaust ventilation may be required for sawing or other processing generating dust.
Protective dust mask during manufacturing processing is recommended in high dust areas.
Personnel allergic to isocyanates are recommended not to work with processing the product.
Grinding and hot work, which could release decomposition products, must not be performed
without proper precautions against exposure.
9. PHYSICAL AND CHEMICA L PROPERTIES
SAFETY DATA SHEET
Divinycell H HP HM HT Matrix HCP Issue date: 2015-06-01 Revised: 2015-06-01 Revision: 0 Page 3(4)
Tel +1 (972) 228-7600
Fax +1 (972) 228-2667
E-mail: info@us.diabgroup.com
Web Site: www.diabgroup.com
Appearance Tan sheets of solid foam with visible cell structure.
Form Chemically inert rigid polymer foam sheet
Boiling Point N/A
Vapor Pressure (mm Hg) N/A
Vapor Density (Air = 1) N/A
Solubility in Water None
Appearance and Odor Foam slabs or sheets / no odor
Specific Gravity (H20 = 1) 0.03 - 0.3
Melting Point N/A
Evaporation Rate N/A
10. STABILITY AND REACTIVITY
Stability Can be used at temperatures of 170 189 F (77 87 C)
Thermally stable to 210 F (100 C)
Avoid exposure to temperatures exceeding 300 F (150 C)
Decomposition by Products HCl, CO, CO2, HCN, NOx during fire conditions
Polymerization N/A Will not occur
11. TOXICOLOGICAL INFORM ATION
No known hazards by handling the product at normal temperatures.
By sawing and during other processes the temperature rises due to friction, traces of
hydrochloric acid and isocyanates may be released. Irritation of the upper respiratory tract is
possible by insufficient ventilation and personnel already sensitized to isocyanates may
respond.
12. ECOLOGICAL INFORMATI ON (NON-MANDATORY)
Limited test results to assess environmental hazard are available, but due to its form, Divinycell
is considered not to be harmful. The product is not soluble in water.
This product is manufactured without CFC s or any other products which act in an ozone
depletion manner
13. DISPOSAL CONSIDERATI ONS (NON-MANDATORY)
SAFETY DATA SHEET
Divinycell H HP HM HT Matrix HCP Issue date: 2015-06-01 Revised: 2015-06-01 Revision: 0 Page 4(4)
Tel +1 (972) 228-7600
Fax +1 (972) 228-2667
E-mail: info@us.diabgroup.com
Web Site: www.diabgroup.com
Non-flammable organic waste.
Not environmentally hazardous waste (SFS 2001:1063).
Waste class: Not hazardous waste (NFS 2004:10). Waste code (EWC): 070213.
Consult local authorities when handling larger quantities of waste.
14. TRANSPORT INFORMATION (NON-MANDATORY)
No known restrictions for Air, Sea, Rail or Ground transportation.
15. REGULATORY INFORMATI ON (NON-MANDATORY)
Not hazardous according to DOT label regulations.
TSCA 8(b): Inventory Status:
All non-polymer ingredients of these materials are listed in the EPA Toxic Substance Control
Act Inventory.
HMIS Rating:
Health: 0
Flammability: 1
Reactivity: 1
16. OTHER INFORMATION
The information contained in this safety data sheet corresponds with our actual knowledge and
experience. It is the user s responsibility to determine the conditions for safe use of this product
and consider laws and regulations.
DIVINYCELL is a product that does not contain dangerous substances and have no substance
intended to be released during normal use and is consequently not regulated by REACH.
THE INFORMATION CONTAINED HEREIN IS BASED ON DATA CONSIDERED TO BE ACCURATE. WHILE THE
INFORMATION IS BELIEVED TO BE RELIABLE, NO WARRANTY IS EXPRESSED OR IMPLIED REGARDING THE ACCURACY
OF THIS DATA OR THE RESULTS TO BE OBTAINED FROM THE USE THEREOF. SINCE THE USE OF THIS INFORMATION
AND THE CONDITIONS AND USE OF THIS PRODUCT ARE CONTROLLED BY THE USER, IT IS THE USER'S OBLIGATION
TO DETERMINE THE CONDITIONS FOR SAFE USE OF THIS PRODUCT.
by | Sep 27, 2025
INDEX
27H80
27H80012P
27H80012PB
27H80025GS
27H80025P
27H80025PA
27H80050GA
27H80050PB
27H80075G
27H80075GS
27H80075PA
27H80100G
27H80100GS
27H80100PA
27H80120GS
27H80150G
27H80150PA
27H80150PL
27H80200P
27H802INPP
27H80375GS
27H80375PB
27H8050GPC
27H8050GSP
27H80625P
27H80DC05A
27H80DC075
27H80DCC03
SAFETY DATA SHEET
Divinycell H HP HM HT Matrix HCP Issue date: 2015-06-01 Revised: 2015-06-01 Revision: 0 Page 1(4)
Tel +1 (972) 228-7600
Fax +1 (972) 228-2667
E-mail: info@us.diabgroup.com
Web Site: www.diabgroup.com
1. IDENTIFICATION
Product: DIVINYCELL H H45, H60, H80, H100, H130
DIVINYCELL HP HP60, HP80, HP100, HP130, HP 160, HP200, HP250
DIVINYCELL HM HM80, HM100, HM130
DIVINYCELL HT HT61, HT81, HT101, HT131
DIVINYCELL MATRIX MATRIX 7-7, MATRIX 10-8, MATRIX 11-9
DIVINYCELL HCP HCP30, HCP50, HCP70, HCP90, HCP100
STRUCTURAL FOAM CORE MATERIAL FOR MFG OF COMPOSITE STRUCTU RES
Supplier: DIAB Americas LP
315 Seahawk Drive
Desoto, TX 75115
Contact: Infotrac
1-800-535-5053
2. HAZARD(S) IDENTIFICATION
The foam material is not hazardous under normal handling and storage conditions. When
exposed to a direct flame, this material will generate acid HCl gas from thermal decomposition.
The primary hazard is dust generation during processing with cutting, sanding and sawing
operations. Dust mask protection should be used when performing these types of operations.
The dust will ignite if given sufficient ignition source and should be processed in a way to avoid
static sparks and accumulation of extra dust in the manufacturing area with good cleaning
practices in the manufacturing areas.
3. COMPOSITION / INFORMATION ON INGRE DIENTS
CHEMICAL NAME CAS NO CONTENT SYMBOLS R-PHRASES
PVC 9002-86-2 30-75 % — —
Aromatic polyurea — 15-50 % — —
Polyamide — 3-10 % — —
These materials are rigid polymeric foams made of alloys of PVC, aromatic polyurea and
polyamide.
4. FIRST-AID MEASURES
SAFETY DATA SHEET
Divinycell H HP HM HT Matrix HCP Issue date: 2015-06-01 Revised: 2015-06-01 Revision: 0 Page 2(4)
Tel +1 (972) 228-7600
Fax +1 (972) 228-2667
E-mail: info@us.diabgroup.com
Web Site: www.diabgroup.com
Inhalation: Fresh air.
Skin contact: No special measures.
Eye contact: By direct contact with shavings or dust, irrigate with flowing water.
Consult medical personnel if irritation persists.
Ingestion: Consult medical personnel if large amounts have been swallowed.
5. FIRE-FIGHTING MEASURES
Oxygen Index > 21% by ASTM D2863
Self Extinguishing by ASTM 1692
Flammable by direct flame only
Hazardous combustion products:
Hydrogen chloride (HCI) and hydrogen cyanide (HCN) can be developed.
Extinguishing media:
Use foam, carbon dioxide, dry chemical, water fog, earth or sand.
Use breathing apparatus against combustion products.
6. ACCIDENTAL RELEASE MEASURES
Spills Not Applicable (Solid Foam form)
7. HANDLING AND STORAGE
Dust can be produced during mechanical process. Use local dust collection system.
Long term storage should be in a cool < 104 F (<40 C) and dry place, away from combustible
material. Avoid exposure to temperatures in excess of 122 F (50 C) during transportation or
short term storage.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Exhaust ventilation may be required for sawing or other processing generating dust.
Protective dust mask during manufacturing processing is recommended in high dust areas.
Personnel allergic to isocyanates are recommended not to work with processing the product.
Grinding and hot work, which could release decomposition products, must not be performed
without proper precautions against exposure.
9. PHYSICAL AND CHEMICA L PROPERTIES
SAFETY DATA SHEET
Divinycell H HP HM HT Matrix HCP Issue date: 2015-06-01 Revised: 2015-06-01 Revision: 0 Page 3(4)
Tel +1 (972) 228-7600
Fax +1 (972) 228-2667
E-mail: info@us.diabgroup.com
Web Site: www.diabgroup.com
Appearance Tan sheets of solid foam with visible cell structure.
Form Chemically inert rigid polymer foam sheet
Boiling Point N/A
Vapor Pressure (mm Hg) N/A
Vapor Density (Air = 1) N/A
Solubility in Water None
Appearance and Odor Foam slabs or sheets / no odor
Specific Gravity (H20 = 1) 0.03 - 0.3
Melting Point N/A
Evaporation Rate N/A
10. STABILITY AND REACTIVITY
Stability Can be used at temperatures of 170 189 F (77 87 C)
Thermally stable to 210 F (100 C)
Avoid exposure to temperatures exceeding 300 F (150 C)
Decomposition by Products HCl, CO, CO2, HCN, NOx during fire conditions
Polymerization N/A Will not occur
11. TOXICOLOGICAL INFORM ATION
No known hazards by handling the product at normal temperatures.
By sawing and during other processes the temperature rises due to friction, traces of
hydrochloric acid and isocyanates may be released. Irritation of the upper respiratory tract is
possible by insufficient ventilation and personnel already sensitized to isocyanates may
respond.
12. ECOLOGICAL INFORMATI ON (NON-MANDATORY)
Limited test results to assess environmental hazard are available, but due to its form, Divinycell
is considered not to be harmful. The product is not soluble in water.
This product is manufactured without CFC s or any other products which act in an ozone
depletion manner
13. DISPOSAL CONSIDERATI ONS (NON-MANDATORY)
SAFETY DATA SHEET
Divinycell H HP HM HT Matrix HCP Issue date: 2015-06-01 Revised: 2015-06-01 Revision: 0 Page 4(4)
Tel +1 (972) 228-7600
Fax +1 (972) 228-2667
E-mail: info@us.diabgroup.com
Web Site: www.diabgroup.com
Non-flammable organic waste.
Not environmentally hazardous waste (SFS 2001:1063).
Waste class: Not hazardous waste (NFS 2004:10). Waste code (EWC): 070213.
Consult local authorities when handling larger quantities of waste.
14. TRANSPORT INFORMATION (NON-MANDATORY)
No known restrictions for Air, Sea, Rail or Ground transportation.
15. REGULATORY INFORMATI ON (NON-MANDATORY)
Not hazardous according to DOT label regulations.
TSCA 8(b): Inventory Status:
All non-polymer ingredients of these materials are listed in the EPA Toxic Substance Control
Act Inventory.
HMIS Rating:
Health: 0
Flammability: 1
Reactivity: 1
16. OTHER INFORMATION
The information contained in this safety data sheet corresponds with our actual knowledge and
experience. It is the user s responsibility to determine the conditions for safe use of this product
and consider laws and regulations.
DIVINYCELL is a product that does not contain dangerous substances and have no substance
intended to be released during normal use and is consequently not regulated by REACH.
THE INFORMATION CONTAINED HEREIN IS BASED ON DATA CONSIDERED TO BE ACCURATE. WHILE THE
INFORMATION IS BELIEVED TO BE RELIABLE, NO WARRANTY IS EXPRESSED OR IMPLIED REGARDING THE ACCURACY
OF THIS DATA OR THE RESULTS TO BE OBTAINED FROM THE USE THEREOF. SINCE THE USE OF THIS INFORMATION
AND THE CONDITIONS AND USE OF THIS PRODUCT ARE CONTROLLED BY THE USER, IT IS THE USER'S OBLIGATION
TO DETERMINE THE CONDITIONS FOR SAFE USE OF THIS PRODUCT.
