POLYURETHANE FOAM | Revchem Composites

25E4070B-D_TDS.pdf

by | Sep 27, 2025

Date: 4/24/20
SPL H4070
Product Information
Physical Properties (Components)
Component A Component B
Viscocity at 75 F (cps) 500 – 700 900 – 1300
Specific Gravity (gr/ml) 1.16 – 1.18 1.06 – 1.08
Physical Properties (Final Product)
Hardness, Shore D, ASTM D-2240 70
Tensile Strength (psi), ASTM D-412 6800
Elongation (%), ASTM D-412 5
Flex Modulus (psi) ASTM D-790 375,000
Color Natural / Black
Handling Characteristics
Mix Ratio by Volume (A/B) 50 / 50
Gel Time at 75 F (seconds) 30 – 60
Tack Free Time 30 – 75
90% Cure Time (hours) 24
Storage and Shelf Life
Packaging
Component A: 55 gallon steel drum (closed top) 500 lb Net Weight
Component B: 55 gallon steel drum (open top) 450 lb Net Weight
Components should be kept well sealed in a dry place from 70 to 90 F. Shelf life of unopened
containers is six (6) months from manufacturing date. Mix Component B well prior to each use. Purge
opened containers with dry nitrogen before resealing. Refer to product SDS for more information.
Non-Warranty: This information is furnished without warranty, expressed or implied, except that is accurate to the best
knowledge of Eteco, Inc. The data on these sheets relates only to the specific material designated herein. Eteco, Inc.
assumes no legal responsibility for use or reliance upon this data. The user should conduct sufficient investigation to establish
the suitability of any product for its intended use.
SPL H4070 is a 100% solids high-performance, multi-purpose polyurethane coating designed for
processing through plural component, high-pressure dispensing equipment. Once fully cured, this
material is tough and hard with excellent tensile strength with moderate impact resistance.
SPL H4070 was designed to be sprayed over EPS and Urethane Board stock. SPL H4070 is also an
excellent product to replace Polyester Resins and Fiberglass.

25E5070Y-D_TDS.pdf

by | Sep 27, 2025

Product Information
Units Test Method Results
Shore D ASTM D-2240 70
psi ASTM D-412 3500 – 4000
psi ASTM D-412 TBD
% ASTM D-412 65
pli ASTM D-624 TBD
– Visual Natural/Pigmented
Units Component A Component B
(A/B) 1 2
(A/B) 35 65
g/mL 1.16 – 1.18 1.06 – 1.08
cPs 50-100 500-700
Visual Pale Yellow Yellow
Seconds
Hours
Storage and Shelf Life
Packaging
Component A: 490Net Weight
Component B: 455Net Weight
Physical Properties (Final Product)
SPL-H 5070 Yellow
TECHNICAL DATA SHEET
Polyurethane Polyurea Spray Elastomer System
SPL-H 5070 is a high-performance, multi-purpose 100% solid polyurethane coating designed to
provide structural support. SPL-H 5070 contains no styrene or HCFC s.
SPL-H 5070 is an excellent replacement for polyester resin and fiberglass. SPL-H 5070 is designed to be
sprayed through most (1:2) plural component high pressure dispensing equipment such as Gusmer, Graco,
PMC and Glasscraft. SPL-H 5070 is tough, flexible with high impact and tear resistance.
Viscocity @ 75 F
Shore Hardness
Tensile Strength
Flexural Modulus
Elongation
Tear Strength
55 gallon steel drum (open top)
For more information contact Eteco, Inc. (714) 480-1370 | info@etecoinc.com
www.etecoinc.com
Non-Warranty: This information is furnished without warranty, expressed or implied, except that is accurate to the best knowledge of Eteco, Inc. The data on
these sheets relates only to the specific material designated herein. Eteco, Inc. assumes no legal responsibility for use or reliance upon this data. The user
should conduct sufficient investigation to establish the suitability of any product for its intended use.
Color
*Final properties will be reached in a course of several days. Properties are typical and not for specifications*
Components should be kept well sealed in a dry place from 70 to 90 F. Shelf life of unopened containers is six
(6) months from manufacturing date. Mix Component B well prior to each use. Purge opened containers with
dry nitrogen before resealing. Refer to product SDS for more information.
55 gallon steel drum (closed top)
90% Cure Time* 24
Color
Gel Time @ 75 F 25 – 40
Handling Characteristics
Mix Ratio by Volume
Mix Ratio by Weight
Specific Gravity @ 75 F

25E4070A-D_TDS.pdf

by | Sep 27, 2025

Date: 4/24/20
SPL H4070
Product Information
Physical Properties (Components)
Component A Component B
Viscocity at 75 F (cps) 500 – 700 900 – 1300
Specific Gravity (gr/ml) 1.16 – 1.18 1.06 – 1.08
Physical Properties (Final Product)
Hardness, Shore D, ASTM D-2240 70
Tensile Strength (psi), ASTM D-412 6800
Elongation (%), ASTM D-412 5
Flex Modulus (psi) ASTM D-790 375,000
Color Natural / Black
Handling Characteristics
Mix Ratio by Volume (A/B) 50 / 50
Gel Time at 75 F (seconds) 30 – 60
Tack Free Time 30 – 75
90% Cure Time (hours) 24
Storage and Shelf Life
Packaging
Component A: 55 gallon steel drum (closed top) 500 lb Net Weight
Component B: 55 gallon steel drum (open top) 450 lb Net Weight
Components should be kept well sealed in a dry place from 70 to 90 F. Shelf life of unopened
containers is six (6) months from manufacturing date. Mix Component B well prior to each use. Purge
opened containers with dry nitrogen before resealing. Refer to product SDS for more information.
Non-Warranty: This information is furnished without warranty, expressed or implied, except that is accurate to the best
knowledge of Eteco, Inc. The data on these sheets relates only to the specific material designated herein. Eteco, Inc.
assumes no legal responsibility for use or reliance upon this data. The user should conduct sufficient investigation to establish
the suitability of any product for its intended use.
SPL H4070 is a 100% solids high-performance, multi-purpose polyurethane coating designed for
processing through plural component, high-pressure dispensing equipment. Once fully cured, this
material is tough and hard with excellent tensile strength with moderate impact resistance.
SPL H4070 was designed to be sprayed over EPS and Urethane Board stock. SPL H4070 is also an
excellent product to replace Polyester Resins and Fiberglass.

25E4011N-D_TDS.pdf

by | Sep 27, 2025

1000 South Linwood Avenue,
Santa Ana, CA 92705
Phone: (714) 480-1370, Fax: (714) 558-1990 Date: 08/23/2006
Revision: 11/01/2008
F 7203

Product Information

F 7203 is a high performance, water blown flexible polyurethane foam designed for processing
through plural component low or high pressure dispensing equipment. Once fully cured, this material
is tough, flexible and dimensionally stable. F 7203 is designed for use in OEM automotive and
recreational applications.

Physical Properties (Components)
Component A Component B
Viscosity at 75oF (cps) 400 – 600 900 -1300
Specific Gravity (gr/ml) 1.09 – 1.12 1.07-1.09

Physical Properties (Final Product)

Tensile Strength (psi), ASTM D-638 30
Elongation (%), ASTM D-638 90
Tear Strength (pli), ASTM D1004 15

Handling Characteristics

Mix Ratio by Weight (Component A/Component B) 50/50
Mix Ratio by Volume (Component A/Component B) 52/48

Cream Time (seconds) 20 – 25
Rise Time (seconds) 70 – 90
Tack Free Time (seconds) 100 – 120
Demold Time (minutes) Mold Temp Dependent
Final Cure Time (hours) 1
Density (pcf) 3.0 3.3

Storage and Shelf Life

Components A and B should be kept well sealed in a dry place at a temperature from 75 – 90oF. Shelf
life of unopened containers is six (6) months from manufacturing date. Purge opened containers with
dry nitrogen before resealing. Premix component B prior to use. Refer to product MSDS for more
information.

Packaging

Component A: 55 gallons steel drum (closed top) 500 lb Net Weight
Component B: 55 gallons steel drum (open top) 450 lb Net Weight

Non-Warranty: This information is furnished without warranty, expressed or implied, except that is
accurate to the best knowledge of Eteco, Inc. The data on these sheets relates only to the specific
material designated herein. Eteco, Inc. assumes no legal responsibility for use or reliance upon this
data. The user should conduct sufficient investigation to establish the suitability of any product for its
intended use.

25DT4-0148_TDS.pdf

by | Sep 27, 2025

TRYMER

4000
POLYISOCYANURATE FOAM INSULATION
DESCRIPTION
Trymer 4000 insulation is a polyurethane modified
polyisocyanurate cellular material. The rigid insulation is
supplied in the of bunstock for fabrication into sheets, pipe
shells, tank and vessel coverings, and other shapes for a
variety of thermal insulation applications. Trymer 4000 insulation
features improved dimensional stability over a wider range of
temperatures than standard polyurethane insulation. Trymer
insulation is not a known nutrient source for mold and mildew.
APPLICATIONS
Trymer 4000 insulation is used extensively in industrial and
commercial applications with moderate density/strength
requirements, within the service temperature range* of -297 F
to +300 F (-183 C to +149 C). Typical applications for Trymer 4000
insulation include:
Fabricated pipe insulation, including elbows and fittings
Core material for factory built panelized constructions
Pipe hangers, saddles and supports
Core material for architectural and structural panels
Tank and vessel insulation
* Trymer PIR can be used at temperatures below -297 F but certain system
design precautions may be necessary. Please consult JM for more information
SIZE
Height: 16 (41 cm)
Width: 48 (122 cm)
Length: 36 (91cm)
96 (244cm)
Custom lengths are also available. Contact your local JM
representative for details.
AVAILABILITY
Trymer 4000 insulation is distributed through JM s extensive
Authorized Fabricator Network.
INSTALLATION
Trymer 4000 insulation is easy to fabricate into various shapes
to meet specific design needs. However, because of the critical
technical design aspects of many of its applications, JM
recommends that qualified designers or consultants design the
total system.
PHYSICAL PROPERTIES
Trymer 4000 insulation exhibits the properties and
characteristics indicated in Table 1 when tested as represented.
Consultation with local building code officials, and design
engineers/specifiers is recommended before application. Like
all cellular plastics, this product will degrade upon prolonged
exposure to sunlight. A covering to block ultraviolet radiation
must be used to prevent this degradation.
ENVIRONMENTAL DATA
Trymer 4000 insulation is specifically formulated to provide
excellent thermal insulation properties without the use of
chlorofluorocarbon (CFC) or hydrochlorofluorocarbon (HCFC)
blowing agents. In compliance with the Montreal Protocol and
the Clean Air Act, Trymer 4000 insulation is manufactured with
hydrocarbon blowing agents, which have no ozone depletion
potential..
SAFETY CONSIDERATIONS
Trymer 4000 insulation requires care in handling. All persons
working with this material must know and follow the proper
handling procedures. The current Safety Data Sheet (SDS) and
General Handling Recommendations for Trymer contain informa-
tion on the safe handling, storage and use of this material, and
can be found at www.jm.com.
TECHNICAL DATA SHEET
05/18/20 (Replaces T4000-05/07/20 )

Technical specifications as shown in this literature are intended to be used as general
guidelines only. Please refer to the Safety Data Sheet and product label prior to using this
product. The physical and chemical properties of the product listed herein represent typical,
average values obtained in accordance with accepted test methods and are subject to normal
manufacturing variations. They are supplied as a technical service and are subject to change
without notice. Any references to numerical flame spread or smoke developed ratings are
not intended to reflect hazards presented by these or any other materials under actual fire
conditions. Check with the Regional Sales Office nearest you for current information.
All Johns Manville products are sold subject to Johns Manville s standard Terms and
Conditions, which includes a Limited Warranty and Limitation of Remedy. For a copy of the
Johns Manville standard Terms and Conditions or for information on other Johns Manville
thermal insulation and systems, visit www.jm.com/terms-conditions or call (800)654-3103.
05/18/20 (Replaces T4000-05/07/20 )
717 17th St.
Denver, CO 80202
(800) 231-1024
JM.com
2020 Johns Manville All Rights Reserved
PHYSICAL PROPERTIES OF TRYMER 4000
(1,2)
ASTM C591, Grade 2, Type V Complies
Density, ASTM D1622
(3)
4 lb/ft
3
(64.0 kg/m
3
)
Compressive Strength, ASTM D1621 95 lb/in
2
(655 kPa) parallel to rise
80 lb/in
2
(550 kPa) perpendicular to rise – width
100 lb/in
2
(690 kPa) perpendicular to rise – length
Compressive Modulus, ASTM D1621 2100 lb/in
2
(14470 kPa) parallel to rise
1800 lb/in
2
(12400 kPa) perpendicular to rise – width
2600 lb/in
2
(17900 kPa) perpendicular to rise – length
Shear Strength, ASTM C273 42 lb/in
2
(290 kPa) parallel and perpendicular avg.
Shear Modulus, ASTM C273 650 lb/in
2
(4480 kPa) parallel and perpendicular avg.
Tensile Strength, ASTM D1623 60 lb/in
2
(413 kPa) parallel to rise – thickness
Flexural Strength, ASTM C203 150 lb/in
2
(1030 kPa) parallel to rise
Flexural Modulus, ASTM C203 3850 lb/in
2
(26540 kPa) parallel to rise
Closed cell Content, ASTM D6226 95%
k-Factor, ASTM C518, @75 F (24 C) mean temp, Aged 180 Days 0.19 Btu in/hr ft
2
F
0.027 W/m C
R-value per Inch, ASTM C578, @75 F (24 C) mean temp, Aged 180 Days
(4)
5.3 hr ft2 F/Btu
0.93 m2 C/W
Water Absorption, ASTM C272 <0.7% by vol. after 24-hour immersion Water Vapor Permeability, ASTM E96 2.9 perms-inch (4.4 ng/Pa s m) Dimensional Stability (5) , ASTM D2126 (%Change) Length Volume At -40 F (-40 C), 7 days -0.4% -0.9% At -10 F (-23 C), 7 days -1.6%-2.0% At 158 F (70 C), 7 days 1.0% 2.0% At 158 F (70 C), 97% R.H. 7 days-1.5%-1.5% At 300 F (149 C), 97% R.H. 7 days-1.3%-1.1% Service Temperature (6,7) -297 F to 300 F (-183 C to 149 C) Surface Burning Characteristics, ASTM E84 (8) < 25 Flame Spread < 450 Smoke Developed (up to 6 thickness) Color Tan (1) All properties are measured at 74 (23 C), unless otherwise indicated. (2) Unless otherwise indicated, data shown are typical values obtained from representative production samples. This data may be used as a guide for design purposes but should not be construed as specifications. For property ranges and specifications, consult your JM representative. (3) Average value through insulation cross section (4) R means resistance to heat flow. The higher the R-value, the greater the insulating power. (5) Frequent and severe thermal cycling can produce dimensional changes significantly greater than those stated here. Special design consideration must be made in systems that cycle frequently. (6) Above 300 F, discoloration and charring will occur, resulting in an increased k-factor in the discolored area. (7) Trymer PIR can be used at temperatures below this but certain system design precautions may be necessary. Please consult JM for more information. (8) This numerical flame spread data is not intended to reflect hazards presented by this or any other material under actual fire conditions. TRYMER 4000 POLYISOCYANURATE FOAM INSULATION TECHNICAL DATA SHEET

25D10266192_TDS.pdf

by | Sep 27, 2025

Froth-Pak

Foam Sealant* is the complete, all-in-one self-
contained and easily portable kit for professional contractors to
quickly and efficiently fill larger gaps and penetrations sealing
out moisture, dust, allergens and pests while improving energy
efficiency, building resilience and comfort for homeowners.
The new Froth-Pak

Sealant has a GWP reduction of over
99% and contains no ozone depleting chemicals or HFCs
while maintaining the performance attributes professional
contractors expect.
Froth-Pak

Sealant s industry-leading, customizable dispensing
system helps ensure consistent flow rate, on-ratio application
and complete dispensing of product. And unlike one-component
foam, Froth-Pak

Sealant is designed to significantly reduce
curing time. It dispenses, expands and becomes tack-free in
seconds.
Froth-Pak

Sealant can be used safely in a wide range of settings,
reducing the potential for unwelcome dust, pests, moisture, mold,
mildew, allergens and rot.
TABLE 1: Sizes and Theoretical Yields for Froth-Pak

Foam Sealant
Product Theoretical Yield,
(1)
board ft
Kits
Froth-Pak

12 12 (0.03)
Froth-Pak

120 120 (0.28)
Froth-Pak

200 200 (0.46)
Froth-Pak

620 620 (1.46)
Refillable Cylinders
Froth-Pak

17 (gal) 2060 (4.85)
Froth-Pak

27 (gal) 3240 (7.65)
Froth-Pak

60 (gal) 6860 (16.2)
Froth-Pak

120 (gal) 15430 (36.4)
Froth-Pak

350 (gal) 43890 (103.6)
1
The theoretical yield has become an industry standard for identifying certain sizes of two-
component kits. Theoretical yield calculations are performed in perfect laboratory conditions,
without taking into account the loss of blowing agent or the variations in application methods
and types.
* Froth-Pak

Foam Sealant is a former product of The Dow Chemical Company.
** Actual cure time will depend on temperature, foam thickness, the specific nozzle used, etc

Ease of Use
Froth-Pak

Sealant is:
Chemically cured foam with reduced curing time
Tack free in 30 seconds and cures in minutes**
Available in refillable cylinders or disposable kits
Useful for multiple applications including roof and wall
junctions; wall and attic penetrations; basements and
crawlspaces; electrical, mechanical and plumbing
penetrations and other gaps, cracks or crevices in the
building envelope
Complete and portable two-component, quick-cure
polyurethane foam kit that fills cavities, penetrations, cracks
and expansion joints
New anti-crossover nozzle and ergonomic dispensing system
results in minimal to no overspray helps ensure consistent
flow rate, on-ratio application and complete dispensing of
product.
Contains no ozone depleting chemicals or HFCs
Blocks air infiltration and helps to meet air change per hour
(ACH) code requirements and reduce building energy costs
Reduces the potential for moisture, mold, mildew, allergens
and rot
One-hour occupant re-entry with proper ventilation after
dispensing
Faster 30 second cure time
Bonds to wood, rigid foam, masonry, metal, drywall and more
Formulation and dispensing systems are patent pending
Froth-Pak

Foam Sealant
Two-Component, Quick Cure, Professional Sealant Kit
HFC-Free, Low GWP, No Ozone Depleting Chemicals
Features and Benefits
Product Information Sheet

TABLE 2: Typical Physical Properties of Froth-Pak

Foam Sealant
These properties are typical but do not constitute specifications.
Property and Test Method Value
Flame Spread/Smoke Developed,
(2)
ASTM E84/UL 723 @ 4 wide by 2 thick 25 / 450
Nominal Density, ASTM D1622, lb/ft
3
1.75
Thermal Resistance
(3)
per inch, ASTM C518, ft
2
h F/Btu, R-value, min.
Initial
Aged LTTR measured at 2 thick
6.7
9.1
Water Vapor Permeance, ASTM E96, perm @ 1 thick 5.4
Water Absorption, ASTM D2842, % by volume 3.4
Air Permeability, ASTM E2178 is 0.0088 L/sec-m
2
@ 75Pa 0
Dimensional Stability, ASTM D2126, % volume change
158 F/100% RH @ 2 wks
-4 F/amb RH @ 2 wks
14
0.3
Compressive Strength, ASTM D1621, lb/in
2
, parallel 16.3
Flexural Strength, ASTM C203, lb/in
2
, parallel 20.1
Tensile Strength, ASTM D1623, lb/in
2
, parallel 29
Shear Strength, ASTM C273, lb/in
2
, parallel 13.8
Maximum Service Temperature, F 240
1
Tested at 2 thickness, full coverage.
2
This numerical flame spread rating is not intended to reflect hazards presented by this or any other material under actual fire conditions.
3
R means resistance to heat flow. The higher the R-value, the greater the insulating power.
Values may differ for Froth Pak 12.0 and specialty kits. Contact a DuPont representative for more information.
Properties
Review all instructions and Safety Data Sheet (SDS) before use. Please contact DuPont at 1-866-583-2583 when additional guidance
is required for writing specifications that include this product.
Testing
Applicable Standards ASTM International
C518 Standard Test Method for Steady-State Thermal
Transmission Properties by Means of the Heat Flow Meter
Apparatus
C273 Standard Test Method for Shear Properties of Sandwich
Core Materials
D1621 Standard Test Method for
Compressive Properties of Rigid Cellular Plastics
D1622 Standard Test Method for Apparent Density of Rigid
Cellular Plastics
D1623 Standard Test Method for Tensile and Tensile Adhesion
Properties of Rigid Cellular Plastics
D2126 Standard Test Method for Response of Rigid Cellular
Plastics to Thermal and Humid Aging
D2842 Standard Test Method for Water Absorption of
Rigid Cellular Plastics
E96 Standard Test Methods for Water Vapor Transmission
of Materials
C203 Standard Test Methods for Breaking Load and
Flexural Properties of Block-Type Thermal Insulation
Notice
Froth-Pak

Foam Sealant complies with the following codes:
CCMC 13447-L
Underwriters Laboratories, Inc. (UL) Classified, see Classification
Certificate R13655
Contact your DuPont sales representative or local authorities
for state and local building code requirements and related
acceptances.
Available Sizes
Froth-Pak

Sealant is typically sold as a complete kit that
includes pressurized A and B cylinders, Insta-Flo

a dispensing
gun/hose assembly and accessories. Froth-Pak

Sealant is also
available in refillable, returnable tanks for applications requiring
a large amount of foam, such as poultry houses. See Table 1 for
size and yield information.

Precautionary Statements
Froth-Pak

Foam will adhere to most surfaces and skin. Avoid
ALL skin contact. Wear gloves and protective clothing. Cured
foam is difficult to remove. Cured foam must be mechanically
removed or allowed to wear off in time.
WARNING: CURED FOAM IS COMBUSTIBLE AND WILL BURN
IF EXPOSED TO OPEN FLAME OR SPARKS FROM HIGH ENERGY
SOURCES. These products should not be sprayed where the
foam may come into contact with hot surfaces, such as
heaters, furnaces, fireplaces, or recessed lighting fixtures.
The foam should NOT be exposed to temperatures over
240 F (116 C).
Avoid overfilling restricted spaces. The reaction of these
chemicals causes expansion and may exert enough force to
cause an uncontrolled stream of foam, spraying the work area
and possibly the operator.
Froth-Pak

contains isocyanate, blowing agent and polyol.
Read all instructions and (M)SDS carefully before use. Wear
protective clothing and cover all skin (including long sleeves),
gloves, goggles or safety glasses, and proper respiratory
protection.
Do not breathe vapor or mist. Use only with adequate
ventilation.
Isocyanate is irritating to the eyes, skin and respiratory system,
and may cause sensitization by inhalation or skin contact.
Contents are under pressure.
Personal Protective Equipment (PPE)
Personal protective equipment (PPE) used during the handling
of Froth-Pak

foam products must at a minimum include:
Protective clothing or impermeable coveralls, such as a
Tyvek

coverall suit, including long sleeves (no skin should
be exposed)
Chemical-resistant gloves that are coated with nitrile, butyl
rubber, neoprene or PVC
Goggles or safety glasses, unless using a full-face respirator
Proper respiratory protection, see section 2.2
PPE should be worn by:
Applicator
Anyone assisting applicator
Other workers in the room within 25 ft of the applicator
Anyone entering the spray area less than one hour post
spraying with proper ventilation
If PPE is contaminated during application, properly discard and
replace immediately. Do not consume or store food or tobacco in
the work area. Make sure to wash your hands and face before
eating or smoking after application.
Safe Handling
WARNING: For Professional Use Only The Froth-Pak

cylinders contain isocyanate, blowing agent and polyols under pressure.
Read and follow product manual and the Safety Data Sheets (SDSs) (formerly MSDSs or Material Safety Data Sheets) carefully
before use. The safety precautions and personal protective equipment indicated below are designed to protect the user and allow
for the safe use and handling of the spray system. Follow all applicable federal, state, local and employer regulations..
Installation
Use Conditions
Complete operating instructions are provided with each
Froth-Pak

Foam Sealant purchase. Read all information
and cautions before application.
Froth-Pak

Foam will adhere to most surfaces and skin.
Avoid ALL skin contact. Wear gloves and protective clothing.
Check with local codes prior to use. If used in an exterior
setting, a coating must be applied for ultraviolet (UV)
protection.
Application
Avoid overfilling restricted spaces. The reaction of these
chemicals causes expansion and may exert enough force to
cause an uncontrolled stream of foam, spraying the work area
and possibly the operator.
One-hour occupant re-entry with proper ventilation after
dispensing.
Curing
Cure time will depend on temperature, foam thickness,
the specific nozzle used, etc.
Cured foam is difficult to remove. Cured foam must be
mechanically removed or allowed to wear off in time.
Equipment
Dispensing gun/hose assembly and accessories included in kit.
* See full ventilation guidelines at building.dupont.com.

For more information visit us at
frothpak.com/sealant
or call 1-833-338-7668
NOTICE: No freedom from any patent owned by DuPont or others is to be inferred. Because use conditions and applicable laws may differ from one location to another and may change with time, Customer is responsible for
determining whether products and the information in this document are appropriate for Customer s use and for ensuring that Customer s workplace and disposal practices are in compliance with applicable laws and other
government enactments. The product shown in this literature may not be available for sale and/or available in all geographies where DuPont is represented. The claims made may not have been approved for use in all
countries or regions. DuPont assumes no obligation or liability for the information in this document. References to DuPont or the Company mean the DuPont legal entity selling the products to Customer unless otherwise
expressly noted. NO EXPRESS WARRANTIES ARE GIVEN EXCEPT FOR ANY APPLICABLE WRITTEN WARRANTIES SPECIFICALLY PROVIDED BY DUPONT. ALL IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE EXPRESSLY EXCLUDED. The buyer assumes all risks as to the use of the material. Buyer s exclusive remedy or any claim (including without limitations, negligence, strict
liability, or tort) shall be limited to the refund of the purchase price of the material. Failure to strictly adhere to any recommended procedures shall release DuPont Specialty Products USA, LLC or its affiliates, of all liability
with respect to the materials or the use thereof. The information herein is not intended for use by non-professional designers, applicators or other persons who do not purchase or utilize this product in the normal course
of their business.
DuPont Polyurethane Foam Insulation and Sealants
CAUTION: When cured, these products are combustible and will burn if exposed to open flame or sparks from high-energy sources. Do not expose to temperatures above 240 F. For more information, consult (M)SDS call
DuPont at 1-866-583-2583 or contact your local building inspector. In an emergency, call 1-866-583-2583. When air sealing buildings, ensure that combustion appliances, such as furnaces, water heaters, wood burning stoves,
gas stoves and gas dryers are properly vented to the outside. See website: http://www.epa.gov/iaq/homes/hip-ventilation.html. In Canada visit: http://archive.nrc-cnrc.gc.ca/eng/ibp/irc/bsi/83-house-ventilation.html.
Froth-Pak

Spray Polyurethane Foam contains isocyanate, blowing agent and polyol. Read all instructions and (M)SDS carefully before use. Wear protective clothing and cover all skin (including long sleeves), gloves, goggles
or safety glasses, and proper respiratory protection. Do not breathe vapor or mist. Use only with adequate ventilation. It is recommended that applicators and those working in the spray area wear respiratory protection.
Increased ventilation significantly reduces the potential for isocyanate exposure; however, supplied air or an approved air-purifying respirator equipped with an organic vapor sorbent and a particulate filter may still be
required to maintain exposure levels below ACGIH, OSHA, WEEL or other applicable limits. For situations where the atmospheric levels may exceed the level for which an air-purifying respirator is effective, use a
positive-pressure, air-supplying respirator (air line or self-contained breathing apparatus). Spraying large amounts of foam indoors may require the use of a positive pressure, air-supplying respirator. Contents under pressure.
Building and/or construction practices unrelated to insulation could greatly affect moisture and the potential for mold formation. No material supplier including DuPont can give assurance that mold will not develop in any
specific system.
DuPont

, the DuPont Oval Logo, and all trademarks and service marks denoted with ,
SM
or are
owned by affiliates of DuPont de Nemours, Inc. unless otherwise noted. 2021 DuPont. 43-D100068-enNA 0521 CDP
IF ATMOSPHERIC LEVELS EXCEED THE LEVEL FOR WHICH
AN AIR-PURIFYING RESPIRATOR IS EFFECTIVE A positive-
pressure, air-supplying respirator such as an air line or
self-contained breathing apparatus.
NIOSH-approved full-face or half-mask airpurifying respirator
with an organic vapor sorbent and a P100 particulate filter
For situations where the atmospheric levels may exceed
the level for which an air-purifying respirator is effective at
maintaining exposure levels below ACGIH, OSHA, WEEL or
other applicable limits, use a positive-pressure, air-supplying
respirator (air line or self-contained breathing apparatus) or
supplied air.
Change out respirator cartridges according to your employer s
change-out schedule (typically 8 hours or end of shift).
The spray foam applicator and anyone within 25 feet of the
applicator, must use approved respiratory protection.
If there is ever a doubt as to the potential limits for worker
exposure, DuPont always recommends a positive-pressure,
air-supplying respirator such as an air line or self-contained
breathing apparatus.

See the Product Manual for details
Disposal
Dispose of any residual DuPont

product, coated debris, or
solvent in accordance with applicable federal, state, and local
government regulations.

25D10269399_TDS.pdf