by | Sep 27, 2025
Product Description
ELFOAM P200 is a 2.0 lb/ft
3
(32 kg/m
3
), rigid, unfaced,
closed cell polyisocyanurate foam supplied as blocks,
sheets and fabricated shapes for a variety of insulation, core
material and carving applications. Polyisocyanurate foam
(polyiso) is similar to polyurethane foam but offers greater
dimensional stability over a wider service temperature range.
ELFOAM P200 is manufactured in bunstock form 26 (66cm)
thick; 48 (122cm) wide; and 72 , 96 , 108 , 120 , and
144 (183cm, 244cm, 274cm, 305cm, and 396cm) long.
Cut sheets are offered in thicknesses from 1/8 to 12 (.32cm
to 30cm) in 1/32 (.08cm) increments. Custom sizes and
fabricated parts up to 26 (66cm) thick, 48 (122cm) wide and
192 (488cm) in length are available for customers wanting
to eliminate in-house cutting, handling, and scrap disposal.
Contact the Indianapolis Sales Office for additional information.
Design Considerations
ELFOAM P200 is designed for use in environments where
temperatures range from -297 to +300 F (-183 to +149 C).
However, in non-laminated applications where temperatures
exceed 140 F (60 C) and/or have relative humidity above 70%
as well as in processes where frequent and severe thermal
cycling occurs, allowances for foam dimensional
changes may need to be incorporated into engineering
design. Regardless of operating conditions, a qualified
design engineer should review all foam applications.
ELFOAM, like all cellular plastics, will degrade with
prolonged exposure to sunlight. To prevent such degradation,
foam materials should be covered. Other barriers to protect
exposed foam surfaces from the elements and to meet
applicable fire and safety regulations may also be required.
Environmental Data
ELFOAM P200 is specifically formulated to provide
excellent physical properties without the use of
chlorofluorocarbon (CFC) or hydrochlorofluorocarbon (HCFC)
blowing agents. In compliance with the Montreal
Protocol and the Clean Air Act, ELFOAM P200 is
manufactured with hydrocarbon blowing agents which
have no ozone depletion or global warming potential.
Applications
Typical products incorporating ELFOAM P200 include:
Refrigerated food service equipment
Laminated wall and roof panels
Commercial and industrial doors
FRP panels, tanks and shelters
Truck/Trailer bodies, shipping containers and railcars
Pipe, tank and vessel insulation
Plugs, patterns and carved products
Note that application testing is often required to
determine suitability of the foam for a specific
application. Potential users should perform pertinent
testing to determine the suitability of the product for the
intended application. Final determination of fitness of the
product for any particular use is the responsibility of the buyer.
Compliances and Approvals
EELFOAM P200 meets industry standards, specifications,
regulations and technical guidelines put forth by numerous
commercial, federal and military entities including ASTM
International, Underwriters Laboratories, and the US
Departments of Transportation and Defense. Contact
the Indianapolis Sales Office for additional information.
Safety
All persons who work with ELFOAM products should
follow proper handling procedures. The ELFOAM
Safety Data Sheet (SDS) contains information about
proper handling, storage and use of this material. A copy
of this document may be downloaded at elliottfoam.com
or obtained by calling the Indianapolis Sales Office.
Availability
All ELFOAM product support, samples, pricing and
orders are coordinated by the Indianapolis Sales Office.
Please call (800) 545-1213 for details. ELFOAM product
data sheets may also be downloaded at elliottfoam.com.
Elliott Company of Indianapolis Inc. (Elliott) believes the information and
recommendations herein to be accurate and reliable as of date of publication.
However, since any assistance furnished by Elliott with reference to the
proper use and disposal of its products is provided without charge and since use
conditions are not within its control, Elliott assumes no obligation or
liability for such assistance. No warranty, expressed or implied, regarding accuracy or
correctness is given and Elliott expressly disclaims any implied warranties including
warranties of merchantability or fitness for a particular use. Since use condi-
tions and government regulations may vary from one location to another and may
change over time, it is the buyer s responsibility to determine whether Elliott prod-
ucts are appropriate for buyer s use, and to assure the buyer s workplace and disposal
procedures are in compliance with law, regulations, ordinances, and other government
enactments applicable in the jurisdiction having authority over the buyer s operations.
ELFOAM
P200
Polyisocyanurate Foam
Manufacturer/Fabricator of ELFOAM Polyiso & Polyurethane Products
September 2016
Family Owned since 1957
Density D1622 2.0 lb/ft
3
31.9 kg/m
3
Thermal Conductivity, k-factor
4
C518
Initial at 75 F (24 C) 0.165 (BTU in)/(hr ft
2
F) 0.024 W/(m C)
Aged 10 days at 158 F (70 C) 0.185 (BTU in)/(hr ft
2
F) 0.027 W/(m C)
Thermal Conductivity, R-value per inch
4
C518
Initial at 75 F (24 C) 6.0 (hr ft
2
F)/BTU 1.06 (m
2
C)/W
Aged 10 days at 158 F (70 C) 5.4 (hr ft
2
F)/BTU 0.96 (m
2
C)/W
Compressive Strength / Modulus D1621
Parallel to Rise 27 / 700 lb/in
2
186 / 4,823 kPa
Perpendicular to Rise
5
18 / 334 lb/in
2
124 / 2,301 kPa
Shear Strength / Modulus C273
Parallel to Rise 25 / 300 lb/in
2
172 / 2,067 kPa
Perpendicular to Rise
5
18 / 220 lb/in
2
124 / 1,515 kPa
Tensile Strength / Modulus
D1623
Parallel to Rise 36 / 1,200 lb/in
2
248 / 8,268 kPa
Perpendicular to Rise
5
26 / 463 lb/in
2
179 / 3,190 kPa
Flexural Strength / Modulus C203
Parallel to Rise 40 / 760 lb/in
2
275 / 5,236 kPa
Perpendicular to Rise
5
28 / 513 lb/in
2
193 / 3,535 kPa
Closed Cell Content (by volume) D6226 95%
Water Absorption (by volume) C272 1.27%
Water Vapor Transmission E96 4.0 perms in 5.8 ng/Pa s m
Dimensional Stability
6
(length / volume change) D2126
+158 F(70 C), 97 3% relativity humidity, 14 days +0.6 / +2.6%
-40 F(-40 C), ambient relativity humidity, 14 days -0.5 / -0.2%
+212 F(100 C), ambient relative humidity, 14 days +0.0 / +0.8%
Coefficient of Linear Thermal Expansion E228
0 to +250 F (-17 to +121 C) 40 x 10
-6
in/in F 72 x 10
-6
mm/mm C
Hot Surface Performance at 300 F (149 C) C411 Pass
Surface Burning Characteristics
7
E84
Flame Spread, thicknesses up to 6 in (15.2 cm) 25
Smoke Developed, thicknesses up to 6 in (15.2 cm) <250
Polyisocyanurate Insulation Requirements C591 Grade 2, Type IV compliant
Product Description
ELFOAM P200 is a rigid, closed cell, preformed, unfaced, polyisocyanurate foam material (polyiso). This CFC and HCFC
free product provides outstanding physical properties in applications having a service temperature between 297 and +300 F
ELFOAM
P200 Polyisocyanurate Foam
ASTM Typical Values
3
Physical Properties
1, 2
Method English Metric
September 2016
(-183 and +149 C). ELFOAM P200 is tan in color and is available in blocks, sheets and fabricated shapes.
1 Data shown are typical values obtained from representative production samples. For specific property ranges, consult the Indianapolis Sales Office.
2 All properties measured at 73 4 F (23 2 C) unless otherwise indicated.
3 To be used only as a guide for design engineering purposes. Potential user is responsible for performing pertinent tests required to determine product suitability for the intended application.
4 k-factors and R-values vary with age and use conditions. Contact Indianapolis Sales Office for values at other mean temperatures.
5 Represents the lowest typical value across all axes related to Perpendicular to Rise performance. Contact the Indianapolis Sales Office for additional information.
6 Frequent and severe thermal cycling can produce dimensional changes significantly greater than those stated here. Special design consideration must be made in applications that cycle frequently.
7 Published data is not intended to reflect hazards represented by this or any other material under actual fire conditions. This material is combustible when exposed to large fire sources.
For more information, contact the Indianapolis Sales Office.
NOTE: Because use conditions and applicable laws may differ from one location to another and may change with time, Buyer is responsible for determining whether the product and information in this
document are appropriate for Buyer's use and for ensuring that Buyer s related products, workplace and disposal practices are in compliance with applicable laws and other government enactments.
Elliott Company of Indianapolis, Inc. assumes no obligation or liability for the information in this document. NO WARRANTIES ARE GIVEN; ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE ARE EXPRESSLY EXCLUDED.
For more information or product samples call
800-545-1213
9200 Zionsville Road Indianapolis, Indiana 46268 Phone: (317) 291-1213 Fax: (317) 291-1219
or visit
elliottfoam.com
Family Owned since 1957
by | Sep 27, 2025
Chemline ED77.9-S75
Polyurethane Elastomer
Description:
Chemline ED77.9-S75 is a two component, 100% solvent free, rigid polyurethane
compound designed for molding applications.
Technical Data
Liquid Properties Component A Component B
Viscosity, cps 1400 cps 850 cps
Specific Gravity 1.18 1.094
Weight/gallon, lbs. 9.8 0.2 9.11 0.2
Color Clear Black
% Solids 100 100
Mix Ratio
By Weight 52 48
By Volume 1.0 1.0
Properties of Mixed System
Gel Time 100gm mass
55-75 Seconds
Hardness Shore D
77
Tensile Strength PSI
4000-5500
Tear Strength Die C PLI
450-600
% Elongation
40-60%
*Values obtained in laboratory setting for comparison purposes only and should not
be considered specifications.
Safety
This product is for industrial use only. Avoid contact with eyes and skin. Do not inhale or ingest. Be sure to read
MSDS in its entirety prior to using.
Storage & Shelf Life
This Product should be stored in sealed containers between 60 F and 90 F. Shelf life is 6 months from the
manufacture date under normal conditions.
Chemline, Inc. 5151 Natural Bridge Rd. St. Louis, MO 63115 Phone : (314) 664 – 2230
While the descriptions, designs, data and information contained herein are presented in good faith and believed to be accurate, it is prov ided for your guidance only. Because many factors may affect
processing or application/use, we recommend that you make tests to determine the suitabil ity of a product for your particular purpose prior to use. NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE, ARE MADE REGARDING PRODUCTS DESCRIBED OR DESIGNS , DATA OR INFORMATION SET FORTH, OR THAT THE PRODUCTS,
DESIGNS, DATA, OR INFORMATION MAY BE USED WITHOUT INFRINGING THE INTELLECTUAL PROPERTY RIGHTS OF OTHERS. IN NO CASE SHALL THE DESCR IPTIONS, INFORMATION, DATA OR DESIGNS PROVIDED BE
CONSIDERED A PART OF OUR TERMS AND CONDITIONS OF SALE. Further, you expressly un derstand and agree that the descriptions, designs, data, and information furnished by Chemline, Inc. hereunder are
prov ided gratis and Chemline assumes no obligation or liability for the descriptions, designs, data and information given or results obtained, all such being giv en and accepted at your risk.
Revised 3/20/19
by | Sep 27, 2025
Chemline ED77.9-S75
Polyurethane Elastomer
Description:
Chemline ED77.9-S75 is a two component, 100% solvent free, rigid polyurethane
compound designed for molding applications.
Technical Data
Liquid Properties Component A Component B
Viscosity, cps 1400 cps 850 cps
Specific Gravity 1.18 1.094
Weight/gallon, lbs. 9.8 0.2 9.11 0.2
Color Clear Black
% Solids 100 100
Mix Ratio
By Weight 52 48
By Volume 1.0 1.0
Properties of Mixed System
Gel Time 100gm mass
55-75 Seconds
Hardness Shore D
77
Tensile Strength PSI
4000-5500
Tear Strength Die C PLI
450-600
% Elongation
40-60%
*Values obtained in laboratory setting for comparison purposes only and should not
be considered specifications.
Safety
This product is for industrial use only. Avoid contact with eyes and skin. Do not inhale or ingest. Be sure to read
MSDS in its entirety prior to using.
Storage & Shelf Life
This Product should be stored in sealed containers between 60 F and 90 F. Shelf life is 6 months from the
manufacture date under normal conditions.
Chemline, Inc. 5151 Natural Bridge Rd. St. Louis, MO 63115 Phone : (314) 664 – 2230
While the descriptions, designs, data and information contained herein are presented in good faith and believed to be accurate, it is prov ided for your guidance only. Because many factors may affect
processing or application/use, we recommend that you make tests to determine the suitabil ity of a product for your particular purpose prior to use. NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE, ARE MADE REGARDING PRODUCTS DESCRIBED OR DESIGNS , DATA OR INFORMATION SET FORTH, OR THAT THE PRODUCTS,
DESIGNS, DATA, OR INFORMATION MAY BE USED WITHOUT INFRINGING THE INTELLECTUAL PROPERTY RIGHTS OF OTHERS. IN NO CASE SHALL THE DESCR IPTIONS, INFORMATION, DATA OR DESIGNS PROVIDED BE
CONSIDERED A PART OF OUR TERMS AND CONDITIONS OF SALE. Further, you expressly un derstand and agree that the descriptions, designs, data, and information furnished by Chemline, Inc. hereunder are
prov ided gratis and Chemline assumes no obligation or liability for the descriptions, designs, data and information given or results obtained, all such being giv en and accepted at your risk.
Revised 3/20/19
by | Sep 27, 2025
Chemline, Inc. 5151 Natural Bridge Rd. St. Louis, MO 63115 Phone : (314) 664 – 2230
While the descriptions, designs, data and information contained herein are presented in good faith and believed to be accurate, it is provided for your guidance only. Because many factors may affect
processing or application/use, we recommend that you make tests to determine the suitability of a product for your particular purpose prior to use. NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE, ARE MADE REGARDING PRODUCTS DESCRIBED OR DESIGNS , DATA OR INFORMATION SET FORTH, OR THAT THE PRODUCTS,
DESIGNS, DATA, OR INFORMATION MAY BE USED WITHOUT INFRINGING THE INTELLECTUAL PROPERTY RIGHTS OF OTHERS. IN NO CASE SHALL THE DESCRIPTIONS, INFORMATION, DATA OR DESIGNS PROVIDED BE
CONSIDERED A PART OF OUR TERMS AND CONDITIONS OF SALE. Further, you expressly understand and agree that the descriptions, designs, data, and information furnished by Chemline, Inc. hereunder are
provided gratis and Chemline assumes no obligation or liability for the descriptions, designs, data and information given or results obtained, all such being given and accepted at your risk.
CHEMLINE ED70.7
Molding Compound (1:1 by Weight)
Description:
Chemline ED70.7 is a two component, MDI-based polyurethane compound. It can be
molded to a variety of shapes and has good heat and impact resistance.
Technical Data
Liquid Properties Component A Component B
Viscosity, cps 40 165
Specific Gravity 1.15 0.03 0.99 0.03
Weight/gallon, lbs. 9.58 0.20 8.22 0.20
Color Neutral Neutral
% Solids 100% 100%
Mix Ratio
By Weight 50 50
By Volume 46.2 53.8
Properties of Mixed System
Gel Time 100 grams 160 Seconds
Hardness (Shore D Durometer) 70D
*Values obtained in laboratory setting for comparison purposes only and should not
be considered specifications.
Safety
This product is for industrial use only. Avoid contact with eyes and skin. Do not inhale or ingest. Be sure to read the
MSDS in its entirety prior to using.
Storage & Shelf Life
This Product should be stored in sealed containers between 60 F and 90 F. Shelf life is 6 months from the
manufacturing date under normal conditions.
Revised 7/10/18
by | Sep 27, 2025
Chemline, Inc. 5151 Natural Bridge Rd. St. Louis, MO 63115 Phone : (314) 664 – 2230
While the descriptions, designs, data and information contained herein are presented in good faith and believed to be accurate, it is provided for your guidance only. Because many factors may affect
processing or application/use, we recommend that you make tests to determine the suitability of a product for your particular purpose prior to use. NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE, ARE MADE REGARDING PRODUCTS DESCRIBED OR DESIGNS , DATA OR INFORMATION SET FORTH, OR THAT THE PRODUCTS,
DESIGNS, DATA, OR INFORMATION MAY BE USED WITHOUT INFRINGING THE INTELLECTUAL PROPERTY RIGHTS OF OTHERS. IN NO CASE SHALL THE DESCRIPTIONS, INFORMATION, DATA OR DESIGNS PROVIDED BE
CONSIDERED A PART OF OUR TERMS AND CONDITIONS OF SALE. Further, you expressly understand and agree that the descriptions, designs, data, and information furnished by Chemline, Inc. hereunder are
provided gratis and Chemline assumes no obligation or liability for the descriptions, designs, data and information given or results obtained, all such being given and accepted at your risk.
CHEMLINE ED70.7
Molding Compound (1:1 by Weight)
Description:
Chemline ED70.7 is a two component, MDI-based polyurethane compound. It can be
molded to a variety of shapes and has good heat and impact resistance.
Technical Data
Liquid Properties Component A Component B
Viscosity, cps 40 165
Specific Gravity 1.15 0.03 0.99 0.03
Weight/gallon, lbs. 9.58 0.20 8.22 0.20
Color Neutral Neutral
% Solids 100% 100%
Mix Ratio
By Weight 50 50
By Volume 46.2 53.8
Properties of Mixed System
Gel Time 100 grams 160 Seconds
Hardness (Shore D Durometer) 70D
*Values obtained in laboratory setting for comparison purposes only and should not
be considered specifications.
Safety
This product is for industrial use only. Avoid contact with eyes and skin. Do not inhale or ingest. Be sure to read the
MSDS in its entirety prior to using.
Storage & Shelf Life
This Product should be stored in sealed containers between 60 F and 90 F. Shelf life is 6 months from the
manufacturing date under normal conditions.
Revised 7/10/18
by | Sep 27, 2025
Date: 4/24/20
SPL H4070
Product Information
Physical Properties (Components)
Component A Component B
Viscocity at 75 F (cps) 500 – 700 900 – 1300
Specific Gravity (gr/ml) 1.16 – 1.18 1.06 – 1.08
Physical Properties (Final Product)
Hardness, Shore D, ASTM D-2240 70
Tensile Strength (psi), ASTM D-412 6800
Elongation (%), ASTM D-412 5
Flex Modulus (psi) ASTM D-790 375,000
Color Natural / Black
Handling Characteristics
Mix Ratio by Volume (A/B) 50 / 50
Gel Time at 75 F (seconds) 30 – 60
Tack Free Time 30 – 75
90% Cure Time (hours) 24
Storage and Shelf Life
Packaging
Component A: 55 gallon steel drum (closed top) 500 lb Net Weight
Component B: 55 gallon steel drum (open top) 450 lb Net Weight
Components should be kept well sealed in a dry place from 70 to 90 F. Shelf life of unopened
containers is six (6) months from manufacturing date. Mix Component B well prior to each use. Purge
opened containers with dry nitrogen before resealing. Refer to product SDS for more information.
Non-Warranty: This information is furnished without warranty, expressed or implied, except that is accurate to the best
knowledge of Eteco, Inc. The data on these sheets relates only to the specific material designated herein. Eteco, Inc.
assumes no legal responsibility for use or reliance upon this data. The user should conduct sufficient investigation to establish
the suitability of any product for its intended use.
SPL H4070 is a 100% solids high-performance, multi-purpose polyurethane coating designed for
processing through plural component, high-pressure dispensing equipment. Once fully cured, this
material is tough and hard with excellent tensile strength with moderate impact resistance.
SPL H4070 was designed to be sprayed over EPS and Urethane Board stock. SPL H4070 is also an
excellent product to replace Polyester Resins and Fiberglass.
by | Sep 27, 2025
Product Information
Units Test Method Results
Shore D ASTM D-2240 70
psi ASTM D-412 3500 – 4000
psi ASTM D-412 TBD
% ASTM D-412 65
pli ASTM D-624 TBD
– Visual Natural/Pigmented
Units Component A Component B
(A/B) 1 2
(A/B) 35 65
g/mL 1.16 – 1.18 1.06 – 1.08
cPs 50-100 500-700
Visual Pale Yellow Yellow
Seconds
Hours
Storage and Shelf Life
Packaging
Component A: 490Net Weight
Component B: 455Net Weight
Physical Properties (Final Product)
SPL-H 5070 Yellow
TECHNICAL DATA SHEET
Polyurethane Polyurea Spray Elastomer System
SPL-H 5070 is a high-performance, multi-purpose 100% solid polyurethane coating designed to
provide structural support. SPL-H 5070 contains no styrene or HCFC s.
SPL-H 5070 is an excellent replacement for polyester resin and fiberglass. SPL-H 5070 is designed to be
sprayed through most (1:2) plural component high pressure dispensing equipment such as Gusmer, Graco,
PMC and Glasscraft. SPL-H 5070 is tough, flexible with high impact and tear resistance.
Viscocity @ 75 F
Shore Hardness
Tensile Strength
Flexural Modulus
Elongation
Tear Strength
55 gallon steel drum (open top)
For more information contact Eteco, Inc. (714) 480-1370 | info@etecoinc.com
www.etecoinc.com
Non-Warranty: This information is furnished without warranty, expressed or implied, except that is accurate to the best knowledge of Eteco, Inc. The data on
these sheets relates only to the specific material designated herein. Eteco, Inc. assumes no legal responsibility for use or reliance upon this data. The user
should conduct sufficient investigation to establish the suitability of any product for its intended use.
Color
*Final properties will be reached in a course of several days. Properties are typical and not for specifications*
Components should be kept well sealed in a dry place from 70 to 90 F. Shelf life of unopened containers is six
(6) months from manufacturing date. Mix Component B well prior to each use. Purge opened containers with
dry nitrogen before resealing. Refer to product SDS for more information.
55 gallon steel drum (closed top)
90% Cure Time* 24
Color
Gel Time @ 75 F 25 – 40
Handling Characteristics
Mix Ratio by Volume
Mix Ratio by Weight
Specific Gravity @ 75 F
by | Sep 27, 2025
Date: 4/24/20
SPL H4070
Product Information
Physical Properties (Components)
Component A Component B
Viscocity at 75 F (cps) 500 – 700 900 – 1300
Specific Gravity (gr/ml) 1.16 – 1.18 1.06 – 1.08
Physical Properties (Final Product)
Hardness, Shore D, ASTM D-2240 70
Tensile Strength (psi), ASTM D-412 6800
Elongation (%), ASTM D-412 5
Flex Modulus (psi) ASTM D-790 375,000
Color Natural / Black
Handling Characteristics
Mix Ratio by Volume (A/B) 50 / 50
Gel Time at 75 F (seconds) 30 – 60
Tack Free Time 30 – 75
90% Cure Time (hours) 24
Storage and Shelf Life
Packaging
Component A: 55 gallon steel drum (closed top) 500 lb Net Weight
Component B: 55 gallon steel drum (open top) 450 lb Net Weight
Components should be kept well sealed in a dry place from 70 to 90 F. Shelf life of unopened
containers is six (6) months from manufacturing date. Mix Component B well prior to each use. Purge
opened containers with dry nitrogen before resealing. Refer to product SDS for more information.
Non-Warranty: This information is furnished without warranty, expressed or implied, except that is accurate to the best
knowledge of Eteco, Inc. The data on these sheets relates only to the specific material designated herein. Eteco, Inc.
assumes no legal responsibility for use or reliance upon this data. The user should conduct sufficient investigation to establish
the suitability of any product for its intended use.
SPL H4070 is a 100% solids high-performance, multi-purpose polyurethane coating designed for
processing through plural component, high-pressure dispensing equipment. Once fully cured, this
material is tough and hard with excellent tensile strength with moderate impact resistance.
SPL H4070 was designed to be sprayed over EPS and Urethane Board stock. SPL H4070 is also an
excellent product to replace Polyester Resins and Fiberglass.
by | Sep 27, 2025
1000 South Linwood Avenue,
Santa Ana, CA 92705
Phone: (714) 480-1370, Fax: (714) 558-1990 Date: 08/23/2006
Revision: 11/01/2008
F 7203
Product Information
F 7203 is a high performance, water blown flexible polyurethane foam designed for processing
through plural component low or high pressure dispensing equipment. Once fully cured, this material
is tough, flexible and dimensionally stable. F 7203 is designed for use in OEM automotive and
recreational applications.
Physical Properties (Components)
Component A Component B
Viscosity at 75oF (cps) 400 – 600 900 -1300
Specific Gravity (gr/ml) 1.09 – 1.12 1.07-1.09
Physical Properties (Final Product)
Tensile Strength (psi), ASTM D-638 30
Elongation (%), ASTM D-638 90
Tear Strength (pli), ASTM D1004 15
Handling Characteristics
Mix Ratio by Weight (Component A/Component B) 50/50
Mix Ratio by Volume (Component A/Component B) 52/48
Cream Time (seconds) 20 – 25
Rise Time (seconds) 70 – 90
Tack Free Time (seconds) 100 – 120
Demold Time (minutes) Mold Temp Dependent
Final Cure Time (hours) 1
Density (pcf) 3.0 3.3
Storage and Shelf Life
Components A and B should be kept well sealed in a dry place at a temperature from 75 – 90oF. Shelf
life of unopened containers is six (6) months from manufacturing date. Purge opened containers with
dry nitrogen before resealing. Premix component B prior to use. Refer to product MSDS for more
information.
Packaging
Component A: 55 gallons steel drum (closed top) 500 lb Net Weight
Component B: 55 gallons steel drum (open top) 450 lb Net Weight
Non-Warranty: This information is furnished without warranty, expressed or implied, except that is
accurate to the best knowledge of Eteco, Inc. The data on these sheets relates only to the specific
material designated herein. Eteco, Inc. assumes no legal responsibility for use or reliance upon this
data. The user should conduct sufficient investigation to establish the suitability of any product for its
intended use.
by | Sep 27, 2025
TRYMER
4000
POLYISOCYANURATE FOAM INSULATION
DESCRIPTION
Trymer 4000 insulation is a polyurethane modified
polyisocyanurate cellular material. The rigid insulation is
supplied in the of bunstock for fabrication into sheets, pipe
shells, tank and vessel coverings, and other shapes for a
variety of thermal insulation applications. Trymer 4000 insulation
features improved dimensional stability over a wider range of
temperatures than standard polyurethane insulation. Trymer
insulation is not a known nutrient source for mold and mildew.
APPLICATIONS
Trymer 4000 insulation is used extensively in industrial and
commercial applications with moderate density/strength
requirements, within the service temperature range* of -297 F
to +300 F (-183 C to +149 C). Typical applications for Trymer 4000
insulation include:
Fabricated pipe insulation, including elbows and fittings
Core material for factory built panelized constructions
Pipe hangers, saddles and supports
Core material for architectural and structural panels
Tank and vessel insulation
* Trymer PIR can be used at temperatures below -297 F but certain system
design precautions may be necessary. Please consult JM for more information
SIZE
Height: 16 (41 cm)
Width: 48 (122 cm)
Length: 36 (91cm)
96 (244cm)
Custom lengths are also available. Contact your local JM
representative for details.
AVAILABILITY
Trymer 4000 insulation is distributed through JM s extensive
Authorized Fabricator Network.
INSTALLATION
Trymer 4000 insulation is easy to fabricate into various shapes
to meet specific design needs. However, because of the critical
technical design aspects of many of its applications, JM
recommends that qualified designers or consultants design the
total system.
PHYSICAL PROPERTIES
Trymer 4000 insulation exhibits the properties and
characteristics indicated in Table 1 when tested as represented.
Consultation with local building code officials, and design
engineers/specifiers is recommended before application. Like
all cellular plastics, this product will degrade upon prolonged
exposure to sunlight. A covering to block ultraviolet radiation
must be used to prevent this degradation.
ENVIRONMENTAL DATA
Trymer 4000 insulation is specifically formulated to provide
excellent thermal insulation properties without the use of
chlorofluorocarbon (CFC) or hydrochlorofluorocarbon (HCFC)
blowing agents. In compliance with the Montreal Protocol and
the Clean Air Act, Trymer 4000 insulation is manufactured with
hydrocarbon blowing agents, which have no ozone depletion
potential..
SAFETY CONSIDERATIONS
Trymer 4000 insulation requires care in handling. All persons
working with this material must know and follow the proper
handling procedures. The current Safety Data Sheet (SDS) and
General Handling Recommendations for Trymer contain informa-
tion on the safe handling, storage and use of this material, and
can be found at www.jm.com.
TECHNICAL DATA SHEET
05/18/20 (Replaces T4000-05/07/20 )
Technical specifications as shown in this literature are intended to be used as general
guidelines only. Please refer to the Safety Data Sheet and product label prior to using this
product. The physical and chemical properties of the product listed herein represent typical,
average values obtained in accordance with accepted test methods and are subject to normal
manufacturing variations. They are supplied as a technical service and are subject to change
without notice. Any references to numerical flame spread or smoke developed ratings are
not intended to reflect hazards presented by these or any other materials under actual fire
conditions. Check with the Regional Sales Office nearest you for current information.
All Johns Manville products are sold subject to Johns Manville s standard Terms and
Conditions, which includes a Limited Warranty and Limitation of Remedy. For a copy of the
Johns Manville standard Terms and Conditions or for information on other Johns Manville
thermal insulation and systems, visit www.jm.com/terms-conditions or call (800)654-3103.
05/18/20 (Replaces T4000-05/07/20 )
717 17th St.
Denver, CO 80202
(800) 231-1024
JM.com
2020 Johns Manville All Rights Reserved
PHYSICAL PROPERTIES OF TRYMER 4000
(1,2)
ASTM C591, Grade 2, Type V Complies
Density, ASTM D1622
(3)
4 lb/ft
3
(64.0 kg/m
3
)
Compressive Strength, ASTM D1621 95 lb/in
2
(655 kPa) parallel to rise
80 lb/in
2
(550 kPa) perpendicular to rise – width
100 lb/in
2
(690 kPa) perpendicular to rise – length
Compressive Modulus, ASTM D1621 2100 lb/in
2
(14470 kPa) parallel to rise
1800 lb/in
2
(12400 kPa) perpendicular to rise – width
2600 lb/in
2
(17900 kPa) perpendicular to rise – length
Shear Strength, ASTM C273 42 lb/in
2
(290 kPa) parallel and perpendicular avg.
Shear Modulus, ASTM C273 650 lb/in
2
(4480 kPa) parallel and perpendicular avg.
Tensile Strength, ASTM D1623 60 lb/in
2
(413 kPa) parallel to rise – thickness
Flexural Strength, ASTM C203 150 lb/in
2
(1030 kPa) parallel to rise
Flexural Modulus, ASTM C203 3850 lb/in
2
(26540 kPa) parallel to rise
Closed cell Content, ASTM D6226 95%
k-Factor, ASTM C518, @75 F (24 C) mean temp, Aged 180 Days 0.19 Btu in/hr ft
2
F
0.027 W/m C
R-value per Inch, ASTM C578, @75 F (24 C) mean temp, Aged 180 Days
(4)
5.3 hr ft2 F/Btu
0.93 m2 C/W
Water Absorption, ASTM C272 <0.7% by vol. after 24-hour immersion
Water Vapor Permeability, ASTM E96 2.9 perms-inch (4.4 ng/Pa s m)
Dimensional Stability
(5)
, ASTM D2126 (%Change) Length Volume
At -40 F (-40 C), 7 days -0.4% -0.9%
At -10 F (-23 C), 7 days -1.6%-2.0%
At 158 F (70 C), 7 days 1.0% 2.0%
At 158 F (70 C), 97% R.H. 7 days-1.5%-1.5%
At 300 F (149 C), 97% R.H. 7 days-1.3%-1.1%
Service Temperature
(6,7)
-297 F to 300 F
(-183 C to 149 C)
Surface Burning Characteristics, ASTM E84
(8)
< 25 Flame Spread
< 450 Smoke Developed (up to 6 thickness)
Color Tan
(1) All properties are measured at 74 (23 C), unless otherwise indicated.
(2) Unless otherwise indicated, data shown are typical values obtained from representative production samples. This data may be used as a guide for design purposes but should not be
construed as specifications. For property ranges and specifications, consult your JM representative.
(3) Average value through insulation cross section
(4) R means resistance to heat flow. The higher the R-value, the greater the insulating power.
(5) Frequent and severe thermal cycling can produce dimensional changes significantly greater than those stated here. Special design consideration must be made in systems that cycle
frequently.
(6) Above 300 F, discoloration and charring will occur, resulting in an increased k-factor in the discolored area.
(7) Trymer PIR can be used at temperatures below this but certain system design precautions may be necessary. Please consult JM for more information.
(8) This numerical flame spread data is not intended to reflect hazards presented by this or any other material under actual fire conditions.
TRYMER
4000
POLYISOCYANURATE FOAM INSULATION
TECHNICAL DATA SHEET
