by | Sep 27, 2025
Gel Coat
Product name
Product type
Section 1. Identification
Chemical family Aromatic.
Relevant identified uses of the substance or mixture and uses advised against
SDS No. NA-1809:5336 (Version: 3.0)
Uses advised against
Identified uses Used in the manufacture of thermoset plastic parts.
No additional information.
G725AA70812
SAFETY DATA SHEET
Date of issue: 04/15/2022
Date of previous issue: 03/01/2020
Emergency telephone number
Supplier’s details
CHEMTREC Within USA and Canada
CHEMTREC Outside USA and Canada
CANUTEC Within Canada
+1 (800) 424-9300
+1 (703) 527-3887
+1 (613) 996-6666
CCN1023
AOC
955 Highway 57 East
Collierville, TN 38017
Phone Number: (901) 854-2800
Hours: 8AM-5pm (Central Time) Mon-Fri
AOC
38 Royal Road
Guelph, Ontario Canada N1H 1G3
Phone Number: (519) 821-5180
Hours: 8am-5pm (Eastern) Mon-Fri
E-Mail: aoc.sds@aocresins.com
Website: www.aocresins.com
United States: Canada:
Section 2. Hazards identification
OSHA/HCS status
FLAMMABLE LIQUIDS Category 3 H226
ACUTE TOXICITY (Inhalation) Category 4 H332
SKIN IRRITATION Category 2 H315
EYE IRRITATION Category 2A H319
CARCINOGENICITY Category 2 H351
REPRODUCTIVE TOXICITY Category 2 H361d
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) Category 3 H335
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) Category 1 H372
ASPIRATION HAZARD Category 1 H304
Classification of the substance or mixture
Signal word
Danger
Hazard statements
H226: Flammable liquid and vapor.
H332: Harmful if inhaled.
H319: Causes serious eye irritation.
H315: Causes skin irritation.
H361d: Suspected of damaging the unborn child.
H351: Suspected of causing cancer.
H304: May be fatal if swallowed and enters airways.
H335: May cause respiratory irritation.
H372: Causes damage to organs through prolonged or repeated exposure. (hearing organs, kidneys)
Hazard pictograms
Precautionary statements
GHS label elements
General
This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Page: 1 of 10Date of issue: 04/15/2022
Date of previous issue: 03/01/2020NA-1809:5336 (Version: 3.0)
G725AA70812
Section 2. Hazards identification
Prevention
P201: Obtain special instructions before use.
P202: Do not handle until all safety precautions have been read and understood.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P210: Keep away from heat, sparks and hot surfaces. – No smoking.
P240: Ground/bond container and receiving equipment.
P241: Use explosion-proof electrical/ventilating/lighting/material-handling equipment.
P242: Use only non-sparking tools.
P243: Take precautionary measures against static discharge.
P233: Keep container tightly closed.
P271: Use only outdoors or in a well-ventilated area.
P260: Do not breathe vapor or mist.
P270: Do not eat, drink or smoke when using this product.
P264: Wash hands thoroughly after handling.
Response
P314: Get medical attention if you feel unwell.
P308+P313: IF exposed or concerned: Get medical attention.
P304+P340: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P312: Call a POISON CENTER or physician if you feel unwell.
P370+P378: In case of fire: Use dry chemical, CO , water spray (fog) or foam.
P301+P310: IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.
P331: Do NOT induce vomiting.
P308+P313: IF exposed or concerned: Get medical advice/attention.
P303+P361+P353: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower.
P362+P364: Take off contaminated clothing and wash it before reuse.
P332+P313: If skin irritation occurs: Get medical attention.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue
rinsing.
P337+P313: If eye irritation persists: Get medical attention.
P391: Collect spillage.
Storage
P405: Store locked up.
P403+P235: Store in a well-ventilated place. Keep cool.
P233: Keep container tightly closed.
Disposal
P501: Dispose of contents and container in accordance with all local, regional, national and international regulations.
P101: If medical advice is needed, have product container or label at hand.
P102: Keep out of reach of children.
Hazards not otherwise classified
None known.
Section 3. Composition/information on ingredients
Ingredient name CAS number %
There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are
classified as hazardous to health or the environment and hence require reporting in this section.
Substance/mixture
Occupational exposure limits, if available, are listed in Section 8.
Mixture.
styrene 100-42-5 20.9
methyl methacrylate 80-62-6 17.7
cobalt bis(2-ethylhexanoate) 136-52-7 0.3
Solvent naphtha (petroleum), light arom. 64742-95-6 0.3
Section 4. First aid measures
Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Use of buffered baby
shampoo will aid in removal. If irritation persists, get medical attention.
Move the victim to a safe area as soon as possible. Allow the victim to rest in a well-ventilated area. If breathing is difficult, give oxygen.
If the victim is not breathing, perform mouth-to-mouth resuscitation. Seek immediate medical attention.
Eye contact
Skin contact
Inhalation
Description of necessary first aid measures
Page: 2 of 10Date of issue: 04/15/2022
Date of previous issue: 03/01/2020NA-1809:5336 (Version: 3.0)
G725AA70812
Section 4. First aid measures
Wash out mouth with water. Remove dentures if any. Stop if the exposed person feels sick as vomiting may be dangerous. Do not
induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not
enter the lungs. Seek immediate medical attention.
In case of contact, immediately flush skin with plenty of water. Remove contaminated clothing and shoes. If irritation persists, seek
medical attention. Wash contaminated clothing before reuse. Clean shoes thoroughly before reuse.
Ingestion
Notes to physician
Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.
Most important symptoms/effects, acute and delayed
See toxicological information (Section 11)
Indication of immediate medical attention and special treatment needed, if necessary
Irritating to mouth, throat and stomach.
Causes serious eye irritation.
Causes skin irritation.
Harmful if inhaled. May cause respiratory irritation. May cause drowsiness or dizziness.
Eye contact
Skin contact
Inhalation
Ingestion
Over-exposure signs/symptoms
Eye contact
Inhalation
Skin contact
Ingestion
Adverse symptoms may include the following: pain or irritation, watering, redness.
Adverse symptoms may include the following: respiratory tract irritation, coughing.
Adverse symptoms may include the following: irritation, redness.
Adverse symptoms may include the following: Irritating to mouth, throat and stomach.
Section 5. Fire-fighting measures
Fire water contaminated with this material must be contained and prevented from being discharged to any waterway, sewer or drain.
Hazardous thermal decomposition products
Specific hazards arising from the chemical
Decomposition products may include the following materials: carbon dioxide
Flammable liquid and vapor. In a fire or if heated, a pressure increase will occur and the container may burst, with the risk of a
subsequent explosion. The vapor/gas is heavier than air and will spread along the ground. Vapors may accumulate in low or confined
areas or travel a considerable distance to a source of ignition and flash back. Runoff to sewer may create fire or explosion hazard. This
material is harmful to aquatic life with long lasting effects. Fire water contaminated with this material must be contained and prevented
from being discharged to any waterway, sewer or drain.
Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated
in positive pressure mode.
Special protective equipment for fire-fighters
Use dry chemical, CO , water spray (fog) or foam.
Extinguishing media
Do not use water jet.
Suitable extinguishing media
Unsuitable extinguishing media
Special protective actions for fire-fighters
Page: 3 of 10Date of issue: 04/15/2022
Date of previous issue: 03/01/2020NA-1809:5336 (Version: 3.0)
G725AA70812
Section 6. Accidental release measures
Environmental precautions
Personal precautions, protective equipment and emergency procedures
Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water courses,
basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-
combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local
regulations (see Section 13). Use spark-proof tools and explosion-proof equipment. Dispose of via a licensed waste disposal contractor.
Contaminated absorbent material may pose the same hazard as the spilled product. Note: see Section 1 for emergency contact
information and Section 13 for waste disposal.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the
product has caused environmental pollution (sewers, waterways, soil or air). Water polluting material. May be harmful to the environment
if released in large quantities.
Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble,
absorb with an inert dry material and place in an appropriate waste disposal container. Use spark-proof tools and explosion-proof
equipment. Dispose of via a licensed waste disposal contractor.
Methods and materials for containment and cleaning up
For non-emergency personnel
For emergency responders
No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Do not touch or walk
through spilled material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Avoid breathing vapor or mist.
Provide adequate ventilation.
If specialised clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials.
Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. See also the information in
“For non-emergency personnel”.
Small spill
Large spill
Section 7. Handling and storage
Advice on general occupational hygiene
Conditions for safe storage, including any incompatibilities
Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash
hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating
areas. See also Section 8 for additional information on hygiene measures.
Store in accordance with local regulations. Store in a segregated and approved area. Store in original container protected from direct
sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Eliminate all
ignition sources. Segregate from oxidizing materials. Keep container tightly closed and sealed until ready for use. Containers that have
been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate
containment to avoid environmental contamination. Refer to the product label and/or technical data sheet for further information.
Protective measures
Put on appropriate personal protective equipment (see Section 8). Eating, drinking and smoking should be prohibited in areas where this
material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove
contaminated clothing and protective equipment before entering eating areas. Do not breathe vapor or mist. Do not ingest. Avoid contact
with eyes, skin and clothing. Avoid release to the environment. Use only with adequate ventilation. Wear appropriate respirator when
ventilation is inadequate. Do not enter storage areas and confined spaces unless adequately ventilated. Keep in the original container or
an approved alternative made from a compatible material, kept tightly closed when not in use. Store and use away from heat, sparks,
open flame or any other ignition source. Use only non-sparking tools. Take precautionary measures against electrostatic discharges.
Empty containers retain product residue and can be hazardous. Do not reuse container.
Precautions for safe handling
styrene ACGIH TLV (United States, 1/2021). Ototoxicant.
TWA: 10 ppm 8 hours.
STEL: 20 ppm 15 minutes.
OSHA PEL Z2 (United States, 2/2013).
TWA: 100 ppm 8 hours.
CEIL: 200 ppm
AMP: 600 ppm 5 minutes.
NIOSH REL (United States, 10/2020).
TWA: 50 ppm 10 hours.
TWA: 215 mg/m 10 hours.
STEL: 100 ppm 15 minutes.
Section 8. Exposure controls/personal protection
Ingredient name Exposure limits
Control parameters
Occupational exposure limits
Page: 4 of 10Date of issue: 04/15/2022
Date of previous issue: 03/01/2020NA-1809:5336 (Version: 3.0)
G725AA70812
Section 8. Exposure controls/personal protection
STEL: 425 mg/m 15 minutes.
methyl methacrylate ACGIH TLV (United States, 1/2021). Skin sensitizer.
TWA: 50 ppm 8 hours.
STEL: 100 ppm 15 minutes.
NIOSH REL (United States, 10/2020).
TWA: 100 ppm 10 hours.
TWA: 410 mg/m 10 hours.
OSHA PEL (United States, 5/2018).
TWA: 100 ppm 8 hours.
TWA: 410 mg/m 8 hours.
ACGIH TLV (United States, 3/2012). Skin sensitizer.
STEL: 410 mg/m 8 hours.
TWA: 205 mg/m 8 hours.
cobalt bis(2-ethylhexanoate) OSHA PEL (United States).
TWA: 0.1 mg/m
ACGIH TLV (United States, 1/2021). Skin sensitizer. Inhalation
sensitizer.
TWA: 0.02 mg/m , (as Co) 8 hours.
Hand protection
Use a properly fitted, air-purifying or air-fed respirator complying with an approved standard if a risk assessment indicates this is
necessary. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe working
limits of the selected respirator.
Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products
if a risk assessment indicates this is necessary.
Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid
exposure to liquid splashes, mists or dusts.
Eye/face protection
Respiratory protection
Body protection
Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be
approved by a specialist before handling this product.
Appropriate engineering controls
Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or other engineering controls to keep worker
exposure to airborne contaminants below any recommended or statutory limits. The engineering controls also need to keep gas, vapor or
dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment.
Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end
of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Ensure that eyewash stations
and safety showers are close to the workstation location.
Hygiene measures
Individual protection measures
Other skin protection
Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks
involved and should be approved by a specialist before handling this product.
Section 9. Physical and chemical properties
Physical state
Melting point
Vapor pressure
Relative density
Vapor density
Liquid.
23.8 F / 30.6 C (Styrene)
1.1 to 1.4 (Water = 1)
3.6 (Air = 1) (Styrene )
5.0 mm Hg@ 68 F / 20 C (Styrene)
Aromatic.Odor
pH
Grey.Color
Evaporation rate < 1 (Butyl acetate = 1)
Flash point 88 F / 31 C (Styrene)
Not applicable.
0.01 - 0.1 ppm (Styrene)Odor threshold
Appearance
Boiling point 293 F / 145 C (Styrene)
Flammability (solid, gas) Not applicable.
Lower and upper explosive (flammable)
limits
Lower: 1.1% Upper: 6.1% (Styrene)
Page: 5 of 10Date of issue: 04/15/2022
Date of previous issue: 03/01/2020NA-1809:5336 (Version: 3.0)
G725AA70812
Section 9. Physical and chemical properties
Solubility Slight.
Auto-ignition temperature 914 F / 490 C (Styrene)
Not available.
Viscosity Not available.
Partition coefficient: n-octanol/water
Molecular weight 1,000 to 15,000
Decomposition temperature Not available.
Section 10. Stability and reactivity
Hazardous decomposition products
Conditions to avoid
Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld, braze, solder, drill, grind or expose containers to heat
or sources of ignition.
Under normal conditions of storage and use, hazardous decomposition products should not be produced.
The product is stable. Stable under recommended storage and handling conditions (see Section 7).
Chemical stability
Reactive or incompatible with the following materials: oxidizing materials
Incompatible materials
Possibility of hazardous reactions
Under normal conditions of storage and use, hazardous reactions will not occur.
Reactivity
No specific test data related to reactivity available for this product or its ingredients.
Section 11. Toxicological information
Acute toxicity
styrene LC50 Inhalation Gas. Rat 2770 ppm 4 hours
LC50 Inhalation Vapor Rat 11800 mg/m 4 hours
LC50 Inhalation Vapor Rat 5634.2 ppm 4 hours
LD50 Oral Rat 2650 mg/kg -
methyl methacrylate LC50 Inhalation Gas. Rat 7094 ppm 4 hours
LC50 Inhalation Vapor Rat 78000 mg/m 4 hours
LD50 Dermal Rabbit >5 g/kg –
LD50 Oral Rat 7872 mg/kg –
LD50 Oral Rat 7872 mg/kg –
cobalt bis(2-ethylhexanoate) LD50 Dermal Rabbit >5 g/kg –
LD50 Oral Rat 1.22 g/kg –
Solvent naphtha (petroleum), light
arom.
LD50 Oral Rat 8400 mg/kg –
Ingredient name Result Species Dose Exposure
Carcinogenicity
Irritation/Corrosion
styrene Eyes – Mild irritant Human – 50 ppm –
Eyes – Moderate irritant Rabbit – 24 hours 100 mg-
Eyes – Severe irritant Rabbit – 100 mg –
Skin – Mild irritant Rabbit – 500 mg –
Skin – Moderate irritant Rabbit – 100 % –
Solvent naphtha (petroleum), light
arom.
Eyes – Mild irritant Rabbit – 24 hours 100 uL-
Ingredient name Result Score Exposure Observation
Sensitization
Species
Information on toxicological effects
Classification
styrene – 2A Reasonably anticipated to be a human carcinogen.
methyl methacrylate – 3 –
cobalt bis(2-ethylhexanoate) – 2B Reasonably anticipated to be a human carcinogen.
Ingredient name NTPIARCACGIH
No data on skin sensitization due to this product.
Page: 6 of 10Date of issue: 04/15/2022
Date of previous issue: 03/01/2020NA-1809:5336 (Version: 3.0)
G725AA70812
Section 11. Toxicological information
Mutagenicity
Teratogenicity
Reproductive toxicity
Inhalation
Harmful if inhaled. May cause respiratory irritation. May cause drowsiness or dizziness.
Irritating to mouth, throat and stomach.
Ingestion
Skin contact
Causes skin irritation.
Causes serious eye irritation.
Eye contact
Symptoms related to the physical, chemical and toxicological characteristics
Skin contact
Ingestion
Adverse symptoms may include the following: respiratory tract irritation, coughing.
Adverse symptoms may include the following: Irritating to mouth, throat and stomach.
Adverse symptoms may include the following: irritation, redness.
Eye contact
Adverse symptoms may include the following: pain or irritation, watering, redness.
Specific target organ toxicity (single exposure)
Specific target organ toxicity (repeated exposure)
Aspiration hazard
Potential acute health effects
No known significant effects or critical hazards.
1) Negative Study A published study concluded that the mechanism for producing cancer in mice exposed to styrene
is not applicable in human metabolism. (June 2013 Pharmacology & Toxicology 66 (2013))
2) Negative Study A recent update to an extensive study of reinforced plastic workers from 1948-1977 concluded that
there was no coherent evidence that styrene exposure increased risk of cancer (March 2013 Epidemiology Vol. 24
Issue 2)
3) Positive Study Styrene induced pulmonary toxicity and carcinogenicity in mice was shown to be caused by a
metabolite of styrene, probably styrene oxide. (Dec.2001 Toxicology Vol.169 Issue 2)
Suspected of damaging the unborn child.
No known significant effects or critical hazards.
May cause respiratory irritation.
A study of long term effects of workers exposed to styrene levels in the range of 25-35 ppm, 8 hour TWA, indicated a possible mild
hearing loss.
May be fatal if swallowed and enters airways.
Inhalation
Section 12. Ecological information
LogPow BCF Potential
Bioaccumulative potential
styrene 0.35 13.49 low
methyl methacrylate 1.38 – low
cobalt bis(2-ethylhexanoate) – 15600 high
Solvent naphtha (petroleum), light
arom.
– 10 to 2500 high
Toxicity
styrene Acute EC50 78000 g/l Marine water Algae – Skeletonema costatum 96 hours
Acute EC50 4700 g/l Fresh water Daphnia – Daphnia magna 48 hours
Acute LC50 52 mg/l Marine water Crustaceans – Artemia salina 48 hours
Acute LC50 4020 g/l Fresh water Fish – Pimephales promelas 96 hours
methyl methacrylate Acute LC50 130000 g/l Fresh water Fish – Pimephales promelas – Adult96 hours
Ingredient name SpeciesResult Exposure
Persistence and degradability
Mobility in soil
Not available.
Ingredient name
Page: 7 of 10Date of issue: 04/15/2022
Date of previous issue: 03/01/2020NA-1809:5336 (Version: 3.0)
G725AA70812
Section 12. Ecological information
Other adverse effects
No known effect according to our database.
Soil/water partition coefficient (KOC)
Not available.
Section 13. Disposal considerations
The generation of waste should be avoided or minimized wherever possible. Empty containers or liners may retain some product residues.
Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Disposal of this product, solutions and any by-
products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local
authority requirements. Avoid disposal. Attempt to use product completely in accordance with intended use. Waste packaging should be
recycled. Incineration or landfill should only be considered when recycling is not feasible.
Disposal methods
The information in this section contains generic advice and guidance. The list of Identified Uses in Section 1 should be consulted for any
available use-specific information provided in the Exposure Scenario(s).
Special precautions
This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not been
cleaned or rinsed out. Empty containers or liners may retain some product residues. Do not cut, weld or grind used containers unless they
have been cleaned thoroughly internally. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers.
Section 14. Transport information
Resin Solution
3
III
UN1866UN number
Proper shipping name
Transport hazard class(es)
Packing group
DOT /TDG / IMDG/IMO / ICAO/IATA and National regulations.
Additional information US regulations require the reporting of spills when the amount exceeds the Reportable
Quantity (RQ) for specific components of this material. See CERCLA in Section 15,
Regulatory Information, for the Reportable Quantities.
Environmental hazards Marine pollutant: No.
Special precautions for user Transport within user s premises: always transport in closed containers that are upright and
secure. Ensure that persons transporting the product know what to do in the event of an
accident or spillage.
IMDGEmergency schedules (EmS): F-E, S-E
Remarks: FP- 31 C
IATANo additional information.
Section 15. Regulatory information
International regulations lists
All components are active or exempted.
SARA 311/312
United States inventory (TSCA 8b)
Australia (AICS) All components are listed or exempted.
Canada (DSL) All components are listed or exempted.
China (IECSC) All components are listed or exempted.
Europe (EINECS) Not determined.
Japan (ENCS) Not determined.
Republic of Korea (KECI) All components are listed or exempted.
New Zealand (NZIoC) All components are listed or exempted.
Philippines (PICCS) At least one component is not listed.
Taiwan (CSNN) All components are listed or exempted.
U.S. Federal regulations
Page: 8 of 10Date of issue: 04/15/2022
Date of previous issue: 03/01/2020NA-1809:5336 (Version: 3.0)
G725AA70812
Section 15. Regulatory information
SARA 313
Ingredient name
styrene 100-42-5
methyl methacrylate 80-62-6
cobalt bis(2-ethylhexanoate) 136-52-7
Form R – Reporting
requirements
CAS number
California Prop. 65
State regulations
styrene – 1000 lbs. (453.6 kg)
methyl methacrylate – 1000 lbs. (453.6 kg)
CERCLA RQ –
WARNING: This product can expose you to chemicals including Styrene and Titanium dioxide, which are known to the State of
California to cause cancer, and Ethylene Glycol, which is known to the State of California to cause birth defects or other reproductive
harm. For more information go to www.P65Warnings.ca.gov.
Per the June 13, 2016 Federal Register notice, EPA harmonized the EPCRA 311/312 hazard categories with the 2012 OSHA hazard
communication standard for classifying and labeling of chemicals (i.e. GHS). Please refer to Section 2 of the SDS to identify the appropriate
hazard categories for reporting purposes.
Section 16. Other information
History
Version
Prepared by
AOC is a registered trademark of the AOC group of companies.
The information contained in this data sheet is based on laboratory data and field experience. We believe this information to be reliable, but do not
guarantee its applicability to the user s process or assume any liability for occurrences arising out of its use. The user, by accepting the products
as described herein, agrees to be responsible for thoroughly testing each such product before committing it to production.
Altek , Atryl , Atryl TCA , Chroma-Tek , EcoTek , FirePel , Hydropel , Moldtru , PulTru , Vibrin , Vicast , Vipel , the AOC name, the
AOC logo, and the Trusted Solutions logo are registered trademarks of the AOC group of companies.
Our recommendations should not be construed as inducements to infringe any patent or violate any law, safety code or insurance regulation.
The information and recommendations contained herein are to the best of our knowledge accurate and reliable, but no rights whatsoever may be
derived by any party other than those expressly agreed to with a selling entity of the AOC group of companies in a legally binding agreement. AOC
hereby makes no warranty of any kind, express or implied, including those of merchantability and fitness for purpose. Unless explicitly agreed to in
writing by AOC otherwise, all offers, quotations, sales and deliveries of AOC products are subject to the general conditions of sale of AOC.
Notice to reader
Date of previous issue
Indicates information that has changed from previously issued version.
Key to abbreviations ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by
the Protocol of 1978. (“Marpol” = marine pollution)
UN = United Nations
04/15/2022
03/01/2020
3.0
National Fire Protection Association (U.S.A.)
Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency Response Copyright 1997, National Fire Protection Association, Quincy, MA 02269. This
reprinted material is not the complete and official position of the National Fire Protection Association, on the referenced subject which is represented only by the standard in its entirety.
Copyright 2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to be interpreted and applied only by properly trained individuals to identify fire, health and
reactivity hazards of chemicals. The user is referred to certain limited number of chemicals with recommended classifications in NFPA 49 and NFPA 325, which would be used as a guideline only. Whether
the chemicals are classified by NFPA or not, anyone using the 704 systems to classify chemicals does so at their own risk.
AOC Corporate Regulatory Affairs
1
3
2
Health
Special
Instability
Flammability
Date of issue
Page: 9 of 10Date of issue: 04/15/2022
Date of previous issue: 03/01/2020NA-1809:5336 (Version: 3.0)
G725AA70812
Section 16. Other information
This Safety Data Sheet (SDS) and its content are the confidential and proprietary information of AOC and it may not be modified, altered,
deconstructed, or presented in any other manner, without the explicit authorization of AOC and/or its legal counsel.
Page: 10 of 10Date of issue: 04/15/2022
Date of previous issue: 03/01/2020NA-1809:5336 (Version: 3.0)
G725AA70812
by | Sep 27, 2025
Gel Coat
Product name
Product type
Emergency telephone number
Section 1. Identification
Chemical family Aromatic.
Supplier’s details AOC, LLC
955 Highway 57 East
Collierville, TN 38017
E-Mail: aoc.sds@aoc-resins.com
Website: www.aoc-resins.com
Phone Number: (901) 854-2800
Hours: 8AM-5pm (Central Time) Monday-Friday
Relevant identified uses of the substance or mixture and uses advised against
SDS No. NA-1707:4207 (Version: 1.0)
Uses advised against
Identified uses Used in the manufacture of thermoset plastic parts.
No additional information.
G730AA70812
CHEMTREC Within USA and Canada
CHEMTREC Outside USA and Canada
CANUTEC Within Canada
+1 (800) 424-9300
+1 (703) 527-3887
+1 (613) 996-6666
CCN1023
SAFETY DATA SHEET
Date of issue: 07/17/2017
Date of previous issue: New SDS
Section 2. Hazards identification
OSHA/HCS status
FLAMMABLE LIQUIDS Category 3 H226
SKIN CORROSION/IRRITATION Category 2 H315
SERIOUS EYE DAMAGE/ EYE IRRITATION Category 2 H319
ACUTE TOXICITY (INHALATION) Category 4 H332
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) Category 3 H335
REPRODUCTIVE TOXICITY Category 2 H361d
CARCINOGENICITY Category 2 H351
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) Category 1 H372
ASPIRATION HAZARD Category 1 H304
Classification of the substance or mixture
Signal word
Danger
Hazard statements
H226: Flammable liquid and vapor.
H332: Harmful if inhaled.
H361d: Suspected of damaging the unborn child.
H351: Suspected of causing cancer.
H319: Causes serious eye irritation.
H315: Causes skin irritation.
H335: May cause respiratory irritation.
H372: Causes damage to organs through prolonged or repeated exposure if inhaled.
H304: May be fatal if swallowed and enters airways.
Hazard pictograms
GHS label elements
This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Page: 1 of 10G730AA70812
Section 2. Hazards identification
Precautionary statements
Prevention
P210: Keep away from heat, sparks, open flames and hot surfaces. – No smoking.
P233: Keep container tightly closed.
P240: Ground/bond container and receiving equipment.
P241: Use explosion-proof electrical/ventilating/lighting/material-handling equipment.
P242: Use only non-sparking tools.
P243: Take precautionary measures against static discharge.
P201: Obtain special instructions before use.
P202: Do not handle until all safety precautions have been read and understood.
P264: Wash hands thoroughly after handling.
P270: Do not eat, drink or smoke when using this product.
P271: Use only outdoors or in a well-ventilated area.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P260: Do not breathe vapor or mist.
Response
P370+P378: In case of fire: Use dry chemical, CO , water spray (fog) or foam.
P301+P310: IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.
P331: Do NOT induce vomiting.
P308+P313: IF exposed or concerned: Get medical advice/attention.
P304+P340: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P312: Call a POISON CENTER or physician if you feel unwell.
P303+P361+P353: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower.
P332+P313: If skin irritation occurs, get medical advice/attention.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing.
P337+P313: If eye irritation persists, get medical advice/attention.
P308+P311: IF exposed or concerned: Call a POISON CENTER or doctor/physician.
P391: Collect spillage.
Storage
P403 + P235: Store in a well-ventilated place. Keep cool.
P233: Keep container tightly closed.
P405: Store locked up.
Disposal
P501: Dispose of contents and container in accordance with all local, regional, national and international regulations.
General
P101: If medical advice is needed, have product container or label at hand.
P102: Keep out of reach of children.
Hazards not otherwise classified
None known.
Section 3. Composition/information on ingredients
Ingredient name CAS number %
There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are
classified as hazardous to health or the environment and hence require reporting in this section.
Substance/mixture :
Occupational exposure limits, if available, are listed in Section 8.
Mixture.
styrene 100-42-5 39.6
2,2-bis(bromomethyl)propane-1,3-diol 3296-90-0 3
cobalt bis(2-ethylhexanoate) 136-52-7 0.3
solvent naphtha (petroleum), light arom. 64742-95-6 0.3
Page: 2 of 10G730AA70812
Wash out mouth with water. Remove dentures if any. Stop if the exposed person feels sick as vomiting may be dangerous. Do
not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit
does not enter the lungs. Seek immediate medical attention.
Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Use of
buffered baby shampoo will aid in removal. If irritation persists, get medical attention.
In case of contact, immediately flush skin with plenty of water. Remove contaminated clothing and shoes. If irritation persists,
seek medical attention. Wash contaminated clothing before reuse. Clean shoes thoroughly before reuse.
Move the victim to a safe area as soon as possible. Allow the victim to rest in a well-ventilated area. If breathing is difficult, give
oxygen. If the victim is not breathing, perform mouth-to-mouth resuscitation. Seek immediate medical attention.
Section 4. First aid measures
Eye contact
Skin contact
Inhalation
Ingestion
Notes to physician
Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.
Description of necessary first aid measures
Most important symptoms/effects, acute and delayed
See toxicological information (Section 11)
Indication of immediate medical attention and special treatment needed, if necessary
Irritating to mouth, throat and stomach.
Causes serious eye irritation.
Causes skin irritation.
Harmful if inhaled. May cause respiratory irritation.
Eye contact
Skin contact
Inhalation
Ingestion
Over-exposure signs/symptoms
Eye contact
Inhalation
Skin contact
Ingestion
Adverse symptoms may include the following: pain or irritation, watering, redness.
Adverse symptoms may include the following: respiratory tract irritation, coughing.
Adverse symptoms may include the following: irritation, redness.
Adverse symptoms may include the following: Irritating to mouth, throat and stomach..
Section 5. Fire-fighting measures
Fire water contaminated with this material must be contained and prevented from being discharged to any waterway, sewer or
drain.
Hazardous thermal decomposition products
Specific hazards arising from the chemical
Decomposition products may include the following materials: carbon dioxide, carbon monoxide, sulfur oxides halogenated
compounds, metal oxide/oxides
Flammable liquid and vapor. In a fire or if heated, a pressure increase will occur and the container may burst, with the risk of a
subsequent explosion. The vapor/gas is heavier than air and will spread along the ground. Vapors may accumulate in low or
confined areas or travel a considerable distance to a source of ignition and flash back. Runoff to sewer may create fire or
explosion hazard. This material is harmful to aquatic life with long lasting effects. Fire water contaminated with this material must
be contained and prevented from being discharged to any waterway, sewer or drain.
Special protective equipment for fire-fighters
Use dry chemical, CO , water spray (fog) or foam.
Extinguishing media
Do not use water jet.
Suitable extinguishing media
Unsuitable extinguishing media
Special protective actions for fire-fighters
Page: 3 of 10G730AA70812
Section 5. Fire-fighting measures
Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece
operated in positive pressure mode.
Section 6. Accidental release measures
Environmental precautions
Personal precautions, protective equipment and emergency procedures
Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water
courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and
collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in
container for disposal according to local regulations (see Section 13). Use spark-proof tools and explosion-proof equipment.
Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled
product. Note: see Section 1 for emergency contact information and Section 13 for waste disposal.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities
if the product has caused environmental pollution (sewers, waterways, soil or air). Water polluting material. May be harmful to
the environment if released in large quantities.
Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-
insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Use spark-proof tools and
explosion-proof equipment. Dispose of via a licensed waste disposal contractor.
Methods and materials for containment and cleaning up
For non-emergency personnel
For emergency responders
No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Do not touch or
walk through spilled material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Avoid breathing vapor or
mist. Provide adequate ventilation.
If specialised clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable
materials. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. See
also the information in “For non-emergency personnel”.
Small spill
Large spill
Section 7. Handling and storage
Advice on general occupational hygiene
Conditions for safe storage, including any incompatibilities
Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers
should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment
before entering eating areas. See also Section 8 for additional information on hygiene measures.
Store in accordance with local regulations. Store in a segregated and approved area. Store in original container protected from
direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink.
Eliminate all ignition sources. Segregate from oxidizing materials. Keep container tightly closed and sealed until ready for use.
Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled
containers. Use appropriate containment to avoid environmental contamination. Refer to the product label and/or technical data
sheet for further information.
Protective measures
Put on appropriate personal protective equipment (see Section 8). Eating, drinking and smoking should be prohibited in areas
where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking.
Remove contaminated clothing and protective equipment before entering eating areas. Do not breathe vapor or mist. Do not
ingest. Avoid contact with eyes, skin and clothing. Avoid release to the environment. Use only with adequate ventilation. Wear
appropriate respirator when ventilation is inadequate. Do not enter storage areas and confined spaces unless adequately
ventilated. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when
not in use. Store and use away from heat, sparks, open flame or any other ignition source. Use explosion-proof electrical
(ventilating, lighting and material handling) equipment. Use only non-sparking tools. Take precautionary measures against
electrostatic discharges. Empty containers retain product residue and can be hazardous. Do not reuse container.
Precautions for safe handling
Page: 4 of 10G730AA70812
styrene ACGIH TLV (United States, 3/2016). Absorbed through skin.
TWA: 20 ppm 8 hours.
TWA: 85 mg/m 8 hours.
STEL: 40 ppm 15 minutes.
STEL: 170 mg/m 15 minutes.
OSHA PEL Z2 (United States, 2/2013).
TWA: 100 ppm 8 hours.
CEIL: 200 ppm
AMP: 600 ppm 5 minutes.
NIOSH REL (United States, 10/2016).
TWA: 50 ppm 10 hours.
TWA: 215 mg/m 10 hours.
STEL: 100 ppm 15 minutes.
STEL: 425 mg/m 15 minutes.
2,2-bis(bromomethyl)propane-1,3-diol AIHA WEEL (United States, 10/2011).
TWA: 0.2 mg/m 8 hours.
cobalt bis(2-ethylhexanoate) OSHA PEL (United States).
TWA: 0.1 mg/m
ACGIH TLV (United States, 3/2016).
TWA: 0.02 mg/m , (as Co) 8 hours.
Section 8. Exposure controls/personal protection
Ingredient name Exposure limits
Hand protection
Use a properly fitted, air-purifying or air-fed respirator complying with an approved standard if a risk assessment indicates this is
necessary. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe
working limits of the selected respirator.
Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical
products if a risk assessment indicates this is necessary.
Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid
exposure to liquid splashes, mists or dusts.
Eye/face protection
Respiratory protection
Body protection
Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should
be approved by a specialist before handling this product.
Appropriate engineering controls
Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or other engineering controls to keep
worker exposure to airborne contaminants below any recommended or statutory limits. The engineering controls also need
to keep gas, vapor or dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment.
Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at
the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Ensure that
eyewash stations and safety showers are close to the workstation location.
Hygiene measures
Control parameters
Individual protection measures
Occupational exposure limits
Other skin protection
Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the
risks involved and should be approved by a specialist before handling this product.
Section 9. Physical and chemical properties
Physical state
Melting point
Liquid.
-23.8 F / -30.6 C (Styrene)
Aromatic.Odor
pH
Grey.Color
Flash point 88 F / 31 C (Styrene)
Not applicable.
0.01 – 0.1 ppm (Styrene)Odor threshold
Appearance
Boiling point 293 F / 145 C (Styrene)
Page: 5 of 10G730AA70812
Section 9. Physical and chemical properties
Vapor pressure
Relative density
Vapor density
Solubility
1.1 to 1.4 (Water = 1)
3.6 (Air = 1) (Styrene )
5.0 mm Hg@ 68 F / 20 C (Styrene)
Slight.
Evaporation rate < 1 (Butyl acetate = 1)
Auto-ignition temperature 914 F / 490 C (Styrene)
Not available.
Viscosity Not available.
Partition coefficient: n-octanol/water
Flammability (solid, gas) Not applicable.
Lower and upper explosive (flammable) limits Lower: 1.1% Upper: 6.1% (Styrene)
Molecular weight Not available.
Decomposition temperature Not available.
Section 10. Stability and reactivity
Hazardous decomposition products
Conditions to avoid
Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld, braze, solder, drill, grind or expose
containers to heat or sources of ignition.
Under normal conditions of storage and use, hazardous decomposition products should not be produced.
The product is stable. Stable under recommended storage and handling conditions (see Section 7).
Chemical stability
Reactive or incompatible with the following materials: oxidizing materials
Incompatible materials
Possibility of hazardous reactions
Under normal conditions of storage and use, hazardous reactions will not occur.
Reactivity
No specific test data related to reactivity available for this product or its ingredients.
Section 11. Toxicological information
Acute toxicity
styrene LC50 Inhalation Gas. Rat 2770 ppm 4 hours
LC50 Inhalation Vapor Rat 11800 mg/m 4 hours
LC50 Inhalation Vapor Rat 5634.2 ppm 4 hours
LD50 Oral Rat 2650 mg/kg -
2,2-bis(bromomethyl)propane-1,
3-diol
LD50 Oral Rat 1880 mg/kg -
cobalt bis(2-ethylhexanoate) LD50 Dermal Rabbit >5 g/kg –
LD50 Oral Rat 1.22 g/kg –
solvent naphtha (petroleum), light
arom.
LD50 Oral Rat 8400 mg/kg –
LD50 Oral Rat 8400 mg/kg –
Product/ingredient name Result Species Dose Exposure
Carcinogenicity
Irritation/Corrosion
styrene Eyes – Mild irritant Human – 50 parts per
million
–
Eyes – Moderate irritant Rabbit – 24 hours 100
milligrams
–
Eyes – Severe irritant Rabbit – 100 milligrams-
Skin – Mild irritant Rabbit – 500 milligrams-
Skin – Moderate irritant Rabbit – 100 Percent –
2,2-bis(bromomethyl)propane-1,
3-diol
Skin – Mild irritant Rabbit – 0.5 Grams –
solvent naphtha (petroleum), light
arom.
Eyes – Mild irritant Rabbit – 24 hours 100
microliters
–
Product/ingredient name Result Score Exposure Observation
Sensitization
Species
Information on toxicological effects
May cause sensitization by skin contact.
Page: 6 of 10G730AA70812
Section 11. Toxicological information
Mutagenicity
Teratogenicity
Reproductive toxicity
Inhalation
Harmful if inhaled. May cause respiratory irritation.
Irritating to mouth, throat and stomach.
Ingestion
Skin contact
Causes skin irritation.
Causes serious eye irritation.
Eye contact
Symptoms related to the physical, chemical and toxicological characteristics
Skin contact
Ingestion
Adverse symptoms may include the following: respiratory tract irritation, coughing.
Adverse symptoms may include the following: Irritating to mouth, throat and stomach..
Adverse symptoms may include the following: irritation, redness.
Eye contact
Adverse symptoms may include the following: pain or irritation, watering, redness.
Specific target organ toxicity (single exposure)
Specific target organ toxicity (repeated exposure)
Aspiration hazard
Potential acute health effects
Classification
styrene – 2B Reasonably anticipated to be a human carcinogen.
2,2-bis(bromomethyl)propane-1,
3-diol
– 2B Reasonably anticipated to be a human carcinogen.
cobalt bis(2-ethylhexanoate) – 2B Reasonably anticipated to be a human carcinogen.
Product/ingredient name NTPIARCACGIH
No mutagenic effect.
1) Negative Study A published study concluded that the mechanism for producing cancer in mice exposed to styrene
is not applicable in human metabolism. (June 2013 Pharmacology & Toxicology 66 (2013))
2) Negative Study A recent update to an extensive study of reinforced plastic workers from 1948-1977 concluded that
there was no coherent evidence that styrene exposure increased risk of cancer (March 2013 Epidemiology Vol. 24
Issue 2)
3) Positive Study Styrene induced pulmonary toxicity and carcinogenicity in mice was shown to be caused by a
metabolite of styrene, probably styrene oxide. (Dec.2001 Toxicology Vol.169 Issue 2)
Not considered to be toxic to the reproductive system.
No known effect according to our database..
No known effect according to our database.
A study of long term effects of workers exposed to styrene levels in the range of 25-35 ppm, 8 hour TWA, indicated a
possible mild hearing loss.
No known effect according to our database.
Inhalation
Section 12. Ecological information
Toxicity
styrene Acute EC50 1400 g/l Fresh water Algae – Pseudokirchneriella subcapitata72 hours
Acute EC50 720 g/l Fresh water Algae – Pseudokirchneriella subcapitata96 hours
Acute EC50 4700 g/l Fresh water Daphnia – Daphnia magna 48 hours
Acute LC50 52 mg/l Marine water Crustaceans – Artemia salina 48 hours
Chronic NOEC 63 g/l Fresh water Algae – Pseudokirchneriella subcapitata96 hours
Product/ingredient name SpeciesResult Exposure
Persistence and degradability
Not available.
Page: 7 of 10G730AA70812
Section 12. Ecological information
LogPow BCF Potential
Bioaccumulative potential
Other adverse effects
No known effect according to our database.
Product/ingredient name
styrene 0.35 13.49 low
2,2-bis(bromomethyl)propane-1,
3-diol
1.08 4.79 low
cobalt bis(2-ethylhexanoate) – 15600 high
solvent naphtha (petroleum), light
arom.
– 10 to 2500 high
Soil/water partition coefficient (KOC)
Not available.
Mobility in soil
Section 13. Disposal considerations
The generation of waste should be avoided or minimized wherever possible. Empty containers or liners may retain some
product residues. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Disposal of
this product, solutions and any by-products should at all times comply with the requirements of environmental protection
and waste disposal legislation and any regional local authority requirements. Avoid disposal. Attempt to use product
completely in accordance with intended use. Waste packaging should be recycled. Incineration or landfill should only be
considered when recycling is not feasible.
Disposal methods
The information in this section contains generic advice and guidance. The list of Identified Uses in Section 1 should be consulted for any available use-specific information
provided in the Exposure Scenario(s).
Special precautions
This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers
that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Do not cut, weld
or grind used containers unless they have been cleaned thoroughly internally. Avoid dispersal of spilled material and runoff
and contact with soil, waterways, drains and sewers.
Section 14. Transport information
Resin Solution
3
III
UN1866UN number
Proper shipping name
Transport hazard class(es)
Packing group
DOT / TDG/ IMDG/IMO / ICAO/IATA and National regulations.
Additional information US regulations require the reporting of spills when the amount exceeds the Reportable
Quantity (RQ) for specific components of this material. See CERCLA in Section 15,
Regulatory Information, for the Reportable Quantities.
Environmental hazards Marine pollutant: No.
Special precautions for user Transport within user s premises: always transport in closed containers that are upright
and secure. Ensure that persons transporting the product know what to do in the event of
an accident or spillage.
IMDGEmergency schedules (EmS): F-E, S-E
Remarks: FP-31 C
IATANo additional information.
Page: 8 of 10G730AA70812
Section 15. Regulatory information
Inventories (National and International)
:All components are listed or exempted.
SARA 313
Product name
styrene 100-42-5
2,2-bis(bromomethyl)propane-1,3-diol 3296-90-0
cobalt bis(2-ethylhexanoate) 136-52-7
Form R – Reporting
requirements
SARA 311/312
styrene Yes. No. No. Yes. Yes.
2,2-bis(bromomethyl)propane-1,3-diol No. No. No. Yes. Yes.
cobalt bis(2-ethylhexanoate) No. No. No. Yes. Yes.
solvent naphtha (petroleum), light arom. Yes. No. No. Yes. Yes.
Name Fire
hazard
Sudden
release of
pressure
Reactive Immediate
(acute)
health hazard
Delayed
(chronic)
health hazard
Composition/information on ingredients
United States inventory (TSCA 8b)
Australia (AICS) :Not determined.
Canada (DSL) :At least one component is not listed in DSL but all such components are listed in NDSL.
China (IECSC) :Not determined.
Europe (EINECS) :Not determined.
Japan (ENCS) :Japan inventory (ENCS): Not determined.
Japan inventory (ISHL): Not determined.
Republic of Korea (KECI) :Not determined.
Malaysia (EHS Register) :Not determined.
New Zealand (NZIoC) :Not determined.
Philippines (PICCS) :Not determined.
Taiwan (CSNN) :Not determined.
CAS number
California Prop. 65
State regulations
styrene – 1000 lbs. (453.6 kg)CERCLA RQ –
WARNING: This product contains a chemical known to the State of California to cause cancer. WARNING: This product
contains less than 1% of a chemical known to the State of California to cause birth defects or other reproductive harm.
Section 16. Other information
History
Date of issue
Version
Date of previous issue
:
:
:
07/17/2017
Not applicable.
1.0
1
3
2
National Fire Protection Association (U.S.A.)
Health
Special
Instability/Reactivity
Flammability
Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency Response Copyright 1997, National Fire Protection Association, Quincy, MA 02269. This
reprinted material is not the complete and official position of the National Fire Protection Association, on the referenced subject which is represented only by the standard in its entirety.
Copyright 2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to be interpreted and applied only by properly trained individuals to identify fire, health and
reactivity hazards of chemicals. The user is referred to certain limited number of chemicals with recommended classifications in NFPA 49 and NFPA 325, which would be used as a guideline only.
Whether the chemicals are classified by NFPA or not, anyone using the 704 systems to classify chemicals does so at their own risk.
AOC Corporate Regulatory Affairs
Page: 9 of 10G730AA70812
Section 16. Other information
The information contained in this data sheet is furnished in good faith and without warranty, representation, or inducement or license of any kind,
except that it is accurate to the best of AOC, LLC’s knowledge, or was obtained from sources believed by AOC, LLC to be reliable. The
accuracy, adequacy or completeness of health and safety precautions set forth herein cannot be guaranteed, and the buyer is solely
responsible for ensuring that the product is used, handled, stored, and disposed of safely and in compliance with applicable federal, state or
provincial, and local laws. AOC, LLC disclaims liability for any loss, damage or personal injury that arises from, or is in any way related to, use
of the information contained in this data sheet.
Notice to reader
Indicates information that has changed from previously issued version.
Key to abbreviations :ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by
the Protocol of 1978. (“Marpol” = marine pollution)
UN = United Nations
This Safety Data Sheet (SDS) and its content are the confidential and proprietary information of AOC and it may not be modified, altered,
deconstructed, or presented in any other manner, without the explicit authorization of AOC and/or its legal counsel.
Page: 10 of 10G730AA70812
by | Sep 27, 2025
Gel Coat
Product name
Product type
Emergency telephone number
Section 1. Identification
Chemical family Aromatic.
Supplier’s details AOC, LLC
955 Highway 57 East
Collierville, TN 38017
E-Mail: aoc.sds@aoc-resins.com
Website: www.aoc-resins.com
Phone Number: (901) 854-2800
Hours: 8AM-5pm (Central Time) Monday-Friday
Relevant identified uses of the substance or mixture and uses advised against
SDS No. NA-1707:4207 (Version: 1.0)
Uses advised against
Identified uses Used in the manufacture of thermoset plastic parts.
No additional information.
G730AA70812
CHEMTREC Within USA and Canada
CHEMTREC Outside USA and Canada
CANUTEC Within Canada
+1 (800) 424-9300
+1 (703) 527-3887
+1 (613) 996-6666
CCN1023
SAFETY DATA SHEET
Date of issue: 07/17/2017
Date of previous issue: New SDS
Section 2. Hazards identification
OSHA/HCS status
FLAMMABLE LIQUIDS Category 3 H226
SKIN CORROSION/IRRITATION Category 2 H315
SERIOUS EYE DAMAGE/ EYE IRRITATION Category 2 H319
ACUTE TOXICITY (INHALATION) Category 4 H332
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) Category 3 H335
REPRODUCTIVE TOXICITY Category 2 H361d
CARCINOGENICITY Category 2 H351
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) Category 1 H372
ASPIRATION HAZARD Category 1 H304
Classification of the substance or mixture
Signal word
Danger
Hazard statements
H226: Flammable liquid and vapor.
H332: Harmful if inhaled.
H361d: Suspected of damaging the unborn child.
H351: Suspected of causing cancer.
H319: Causes serious eye irritation.
H315: Causes skin irritation.
H335: May cause respiratory irritation.
H372: Causes damage to organs through prolonged or repeated exposure if inhaled.
H304: May be fatal if swallowed and enters airways.
Hazard pictograms
GHS label elements
This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Page: 1 of 10G730AA70812
Section 2. Hazards identification
Precautionary statements
Prevention
P210: Keep away from heat, sparks, open flames and hot surfaces. – No smoking.
P233: Keep container tightly closed.
P240: Ground/bond container and receiving equipment.
P241: Use explosion-proof electrical/ventilating/lighting/material-handling equipment.
P242: Use only non-sparking tools.
P243: Take precautionary measures against static discharge.
P201: Obtain special instructions before use.
P202: Do not handle until all safety precautions have been read and understood.
P264: Wash hands thoroughly after handling.
P270: Do not eat, drink or smoke when using this product.
P271: Use only outdoors or in a well-ventilated area.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P260: Do not breathe vapor or mist.
Response
P370+P378: In case of fire: Use dry chemical, CO , water spray (fog) or foam.
P301+P310: IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.
P331: Do NOT induce vomiting.
P308+P313: IF exposed or concerned: Get medical advice/attention.
P304+P340: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P312: Call a POISON CENTER or physician if you feel unwell.
P303+P361+P353: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower.
P332+P313: If skin irritation occurs, get medical advice/attention.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing.
P337+P313: If eye irritation persists, get medical advice/attention.
P308+P311: IF exposed or concerned: Call a POISON CENTER or doctor/physician.
P391: Collect spillage.
Storage
P403 + P235: Store in a well-ventilated place. Keep cool.
P233: Keep container tightly closed.
P405: Store locked up.
Disposal
P501: Dispose of contents and container in accordance with all local, regional, national and international regulations.
General
P101: If medical advice is needed, have product container or label at hand.
P102: Keep out of reach of children.
Hazards not otherwise classified
None known.
Section 3. Composition/information on ingredients
Ingredient name CAS number %
There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are
classified as hazardous to health or the environment and hence require reporting in this section.
Substance/mixture :
Occupational exposure limits, if available, are listed in Section 8.
Mixture.
styrene 100-42-5 39.6
2,2-bis(bromomethyl)propane-1,3-diol 3296-90-0 3
cobalt bis(2-ethylhexanoate) 136-52-7 0.3
solvent naphtha (petroleum), light arom. 64742-95-6 0.3
Page: 2 of 10G730AA70812
Wash out mouth with water. Remove dentures if any. Stop if the exposed person feels sick as vomiting may be dangerous. Do
not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit
does not enter the lungs. Seek immediate medical attention.
Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Use of
buffered baby shampoo will aid in removal. If irritation persists, get medical attention.
In case of contact, immediately flush skin with plenty of water. Remove contaminated clothing and shoes. If irritation persists,
seek medical attention. Wash contaminated clothing before reuse. Clean shoes thoroughly before reuse.
Move the victim to a safe area as soon as possible. Allow the victim to rest in a well-ventilated area. If breathing is difficult, give
oxygen. If the victim is not breathing, perform mouth-to-mouth resuscitation. Seek immediate medical attention.
Section 4. First aid measures
Eye contact
Skin contact
Inhalation
Ingestion
Notes to physician
Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.
Description of necessary first aid measures
Most important symptoms/effects, acute and delayed
See toxicological information (Section 11)
Indication of immediate medical attention and special treatment needed, if necessary
Irritating to mouth, throat and stomach.
Causes serious eye irritation.
Causes skin irritation.
Harmful if inhaled. May cause respiratory irritation.
Eye contact
Skin contact
Inhalation
Ingestion
Over-exposure signs/symptoms
Eye contact
Inhalation
Skin contact
Ingestion
Adverse symptoms may include the following: pain or irritation, watering, redness.
Adverse symptoms may include the following: respiratory tract irritation, coughing.
Adverse symptoms may include the following: irritation, redness.
Adverse symptoms may include the following: Irritating to mouth, throat and stomach..
Section 5. Fire-fighting measures
Fire water contaminated with this material must be contained and prevented from being discharged to any waterway, sewer or
drain.
Hazardous thermal decomposition products
Specific hazards arising from the chemical
Decomposition products may include the following materials: carbon dioxide, carbon monoxide, sulfur oxides halogenated
compounds, metal oxide/oxides
Flammable liquid and vapor. In a fire or if heated, a pressure increase will occur and the container may burst, with the risk of a
subsequent explosion. The vapor/gas is heavier than air and will spread along the ground. Vapors may accumulate in low or
confined areas or travel a considerable distance to a source of ignition and flash back. Runoff to sewer may create fire or
explosion hazard. This material is harmful to aquatic life with long lasting effects. Fire water contaminated with this material must
be contained and prevented from being discharged to any waterway, sewer or drain.
Special protective equipment for fire-fighters
Use dry chemical, CO , water spray (fog) or foam.
Extinguishing media
Do not use water jet.
Suitable extinguishing media
Unsuitable extinguishing media
Special protective actions for fire-fighters
Page: 3 of 10G730AA70812
Section 5. Fire-fighting measures
Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece
operated in positive pressure mode.
Section 6. Accidental release measures
Environmental precautions
Personal precautions, protective equipment and emergency procedures
Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water
courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and
collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in
container for disposal according to local regulations (see Section 13). Use spark-proof tools and explosion-proof equipment.
Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled
product. Note: see Section 1 for emergency contact information and Section 13 for waste disposal.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities
if the product has caused environmental pollution (sewers, waterways, soil or air). Water polluting material. May be harmful to
the environment if released in large quantities.
Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-
insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Use spark-proof tools and
explosion-proof equipment. Dispose of via a licensed waste disposal contractor.
Methods and materials for containment and cleaning up
For non-emergency personnel
For emergency responders
No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Do not touch or
walk through spilled material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Avoid breathing vapor or
mist. Provide adequate ventilation.
If specialised clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable
materials. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. See
also the information in “For non-emergency personnel”.
Small spill
Large spill
Section 7. Handling and storage
Advice on general occupational hygiene
Conditions for safe storage, including any incompatibilities
Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers
should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment
before entering eating areas. See also Section 8 for additional information on hygiene measures.
Store in accordance with local regulations. Store in a segregated and approved area. Store in original container protected from
direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink.
Eliminate all ignition sources. Segregate from oxidizing materials. Keep container tightly closed and sealed until ready for use.
Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled
containers. Use appropriate containment to avoid environmental contamination. Refer to the product label and/or technical data
sheet for further information.
Protective measures
Put on appropriate personal protective equipment (see Section 8). Eating, drinking and smoking should be prohibited in areas
where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking.
Remove contaminated clothing and protective equipment before entering eating areas. Do not breathe vapor or mist. Do not
ingest. Avoid contact with eyes, skin and clothing. Avoid release to the environment. Use only with adequate ventilation. Wear
appropriate respirator when ventilation is inadequate. Do not enter storage areas and confined spaces unless adequately
ventilated. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when
not in use. Store and use away from heat, sparks, open flame or any other ignition source. Use explosion-proof electrical
(ventilating, lighting and material handling) equipment. Use only non-sparking tools. Take precautionary measures against
electrostatic discharges. Empty containers retain product residue and can be hazardous. Do not reuse container.
Precautions for safe handling
Page: 4 of 10G730AA70812
styrene ACGIH TLV (United States, 3/2016). Absorbed through skin.
TWA: 20 ppm 8 hours.
TWA: 85 mg/m 8 hours.
STEL: 40 ppm 15 minutes.
STEL: 170 mg/m 15 minutes.
OSHA PEL Z2 (United States, 2/2013).
TWA: 100 ppm 8 hours.
CEIL: 200 ppm
AMP: 600 ppm 5 minutes.
NIOSH REL (United States, 10/2016).
TWA: 50 ppm 10 hours.
TWA: 215 mg/m 10 hours.
STEL: 100 ppm 15 minutes.
STEL: 425 mg/m 15 minutes.
2,2-bis(bromomethyl)propane-1,3-diol AIHA WEEL (United States, 10/2011).
TWA: 0.2 mg/m 8 hours.
cobalt bis(2-ethylhexanoate) OSHA PEL (United States).
TWA: 0.1 mg/m
ACGIH TLV (United States, 3/2016).
TWA: 0.02 mg/m , (as Co) 8 hours.
Section 8. Exposure controls/personal protection
Ingredient name Exposure limits
Hand protection
Use a properly fitted, air-purifying or air-fed respirator complying with an approved standard if a risk assessment indicates this is
necessary. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe
working limits of the selected respirator.
Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical
products if a risk assessment indicates this is necessary.
Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid
exposure to liquid splashes, mists or dusts.
Eye/face protection
Respiratory protection
Body protection
Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should
be approved by a specialist before handling this product.
Appropriate engineering controls
Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or other engineering controls to keep
worker exposure to airborne contaminants below any recommended or statutory limits. The engineering controls also need
to keep gas, vapor or dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment.
Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at
the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Ensure that
eyewash stations and safety showers are close to the workstation location.
Hygiene measures
Control parameters
Individual protection measures
Occupational exposure limits
Other skin protection
Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the
risks involved and should be approved by a specialist before handling this product.
Section 9. Physical and chemical properties
Physical state
Melting point
Liquid.
-23.8 F / -30.6 C (Styrene)
Aromatic.Odor
pH
Grey.Color
Flash point 88 F / 31 C (Styrene)
Not applicable.
0.01 – 0.1 ppm (Styrene)Odor threshold
Appearance
Boiling point 293 F / 145 C (Styrene)
Page: 5 of 10G730AA70812
Section 9. Physical and chemical properties
Vapor pressure
Relative density
Vapor density
Solubility
1.1 to 1.4 (Water = 1)
3.6 (Air = 1) (Styrene )
5.0 mm Hg@ 68 F / 20 C (Styrene)
Slight.
Evaporation rate < 1 (Butyl acetate = 1)
Auto-ignition temperature 914 F / 490 C (Styrene)
Not available.
Viscosity Not available.
Partition coefficient: n-octanol/water
Flammability (solid, gas) Not applicable.
Lower and upper explosive (flammable) limits Lower: 1.1% Upper: 6.1% (Styrene)
Molecular weight Not available.
Decomposition temperature Not available.
Section 10. Stability and reactivity
Hazardous decomposition products
Conditions to avoid
Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld, braze, solder, drill, grind or expose
containers to heat or sources of ignition.
Under normal conditions of storage and use, hazardous decomposition products should not be produced.
The product is stable. Stable under recommended storage and handling conditions (see Section 7).
Chemical stability
Reactive or incompatible with the following materials: oxidizing materials
Incompatible materials
Possibility of hazardous reactions
Under normal conditions of storage and use, hazardous reactions will not occur.
Reactivity
No specific test data related to reactivity available for this product or its ingredients.
Section 11. Toxicological information
Acute toxicity
styrene LC50 Inhalation Gas. Rat 2770 ppm 4 hours
LC50 Inhalation Vapor Rat 11800 mg/m 4 hours
LC50 Inhalation Vapor Rat 5634.2 ppm 4 hours
LD50 Oral Rat 2650 mg/kg -
2,2-bis(bromomethyl)propane-1,
3-diol
LD50 Oral Rat 1880 mg/kg -
cobalt bis(2-ethylhexanoate) LD50 Dermal Rabbit >5 g/kg –
LD50 Oral Rat 1.22 g/kg –
solvent naphtha (petroleum), light
arom.
LD50 Oral Rat 8400 mg/kg –
LD50 Oral Rat 8400 mg/kg –
Product/ingredient name Result Species Dose Exposure
Carcinogenicity
Irritation/Corrosion
styrene Eyes – Mild irritant Human – 50 parts per
million
–
Eyes – Moderate irritant Rabbit – 24 hours 100
milligrams
–
Eyes – Severe irritant Rabbit – 100 milligrams-
Skin – Mild irritant Rabbit – 500 milligrams-
Skin – Moderate irritant Rabbit – 100 Percent –
2,2-bis(bromomethyl)propane-1,
3-diol
Skin – Mild irritant Rabbit – 0.5 Grams –
solvent naphtha (petroleum), light
arom.
Eyes – Mild irritant Rabbit – 24 hours 100
microliters
–
Product/ingredient name Result Score Exposure Observation
Sensitization
Species
Information on toxicological effects
May cause sensitization by skin contact.
Page: 6 of 10G730AA70812
Section 11. Toxicological information
Mutagenicity
Teratogenicity
Reproductive toxicity
Inhalation
Harmful if inhaled. May cause respiratory irritation.
Irritating to mouth, throat and stomach.
Ingestion
Skin contact
Causes skin irritation.
Causes serious eye irritation.
Eye contact
Symptoms related to the physical, chemical and toxicological characteristics
Skin contact
Ingestion
Adverse symptoms may include the following: respiratory tract irritation, coughing.
Adverse symptoms may include the following: Irritating to mouth, throat and stomach..
Adverse symptoms may include the following: irritation, redness.
Eye contact
Adverse symptoms may include the following: pain or irritation, watering, redness.
Specific target organ toxicity (single exposure)
Specific target organ toxicity (repeated exposure)
Aspiration hazard
Potential acute health effects
Classification
styrene – 2B Reasonably anticipated to be a human carcinogen.
2,2-bis(bromomethyl)propane-1,
3-diol
– 2B Reasonably anticipated to be a human carcinogen.
cobalt bis(2-ethylhexanoate) – 2B Reasonably anticipated to be a human carcinogen.
Product/ingredient name NTPIARCACGIH
No mutagenic effect.
1) Negative Study A published study concluded that the mechanism for producing cancer in mice exposed to styrene
is not applicable in human metabolism. (June 2013 Pharmacology & Toxicology 66 (2013))
2) Negative Study A recent update to an extensive study of reinforced plastic workers from 1948-1977 concluded that
there was no coherent evidence that styrene exposure increased risk of cancer (March 2013 Epidemiology Vol. 24
Issue 2)
3) Positive Study Styrene induced pulmonary toxicity and carcinogenicity in mice was shown to be caused by a
metabolite of styrene, probably styrene oxide. (Dec.2001 Toxicology Vol.169 Issue 2)
Not considered to be toxic to the reproductive system.
No known effect according to our database..
No known effect according to our database.
A study of long term effects of workers exposed to styrene levels in the range of 25-35 ppm, 8 hour TWA, indicated a
possible mild hearing loss.
No known effect according to our database.
Inhalation
Section 12. Ecological information
Toxicity
styrene Acute EC50 1400 g/l Fresh water Algae – Pseudokirchneriella subcapitata72 hours
Acute EC50 720 g/l Fresh water Algae – Pseudokirchneriella subcapitata96 hours
Acute EC50 4700 g/l Fresh water Daphnia – Daphnia magna 48 hours
Acute LC50 52 mg/l Marine water Crustaceans – Artemia salina 48 hours
Chronic NOEC 63 g/l Fresh water Algae – Pseudokirchneriella subcapitata96 hours
Product/ingredient name SpeciesResult Exposure
Persistence and degradability
Not available.
Page: 7 of 10G730AA70812
Section 12. Ecological information
LogPow BCF Potential
Bioaccumulative potential
Other adverse effects
No known effect according to our database.
Product/ingredient name
styrene 0.35 13.49 low
2,2-bis(bromomethyl)propane-1,
3-diol
1.08 4.79 low
cobalt bis(2-ethylhexanoate) – 15600 high
solvent naphtha (petroleum), light
arom.
– 10 to 2500 high
Soil/water partition coefficient (KOC)
Not available.
Mobility in soil
Section 13. Disposal considerations
The generation of waste should be avoided or minimized wherever possible. Empty containers or liners may retain some
product residues. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Disposal of
this product, solutions and any by-products should at all times comply with the requirements of environmental protection
and waste disposal legislation and any regional local authority requirements. Avoid disposal. Attempt to use product
completely in accordance with intended use. Waste packaging should be recycled. Incineration or landfill should only be
considered when recycling is not feasible.
Disposal methods
The information in this section contains generic advice and guidance. The list of Identified Uses in Section 1 should be consulted for any available use-specific information
provided in the Exposure Scenario(s).
Special precautions
This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers
that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Do not cut, weld
or grind used containers unless they have been cleaned thoroughly internally. Avoid dispersal of spilled material and runoff
and contact with soil, waterways, drains and sewers.
Section 14. Transport information
Resin Solution
3
III
UN1866UN number
Proper shipping name
Transport hazard class(es)
Packing group
DOT / TDG/ IMDG/IMO / ICAO/IATA and National regulations.
Additional information US regulations require the reporting of spills when the amount exceeds the Reportable
Quantity (RQ) for specific components of this material. See CERCLA in Section 15,
Regulatory Information, for the Reportable Quantities.
Environmental hazards Marine pollutant: No.
Special precautions for user Transport within user s premises: always transport in closed containers that are upright
and secure. Ensure that persons transporting the product know what to do in the event of
an accident or spillage.
IMDGEmergency schedules (EmS): F-E, S-E
Remarks: FP-31 C
IATANo additional information.
Page: 8 of 10G730AA70812
Section 15. Regulatory information
Inventories (National and International)
:All components are listed or exempted.
SARA 313
Product name
styrene 100-42-5
2,2-bis(bromomethyl)propane-1,3-diol 3296-90-0
cobalt bis(2-ethylhexanoate) 136-52-7
Form R – Reporting
requirements
SARA 311/312
styrene Yes. No. No. Yes. Yes.
2,2-bis(bromomethyl)propane-1,3-diol No. No. No. Yes. Yes.
cobalt bis(2-ethylhexanoate) No. No. No. Yes. Yes.
solvent naphtha (petroleum), light arom. Yes. No. No. Yes. Yes.
Name Fire
hazard
Sudden
release of
pressure
Reactive Immediate
(acute)
health hazard
Delayed
(chronic)
health hazard
Composition/information on ingredients
United States inventory (TSCA 8b)
Australia (AICS) :Not determined.
Canada (DSL) :At least one component is not listed in DSL but all such components are listed in NDSL.
China (IECSC) :Not determined.
Europe (EINECS) :Not determined.
Japan (ENCS) :Japan inventory (ENCS): Not determined.
Japan inventory (ISHL): Not determined.
Republic of Korea (KECI) :Not determined.
Malaysia (EHS Register) :Not determined.
New Zealand (NZIoC) :Not determined.
Philippines (PICCS) :Not determined.
Taiwan (CSNN) :Not determined.
CAS number
California Prop. 65
State regulations
styrene – 1000 lbs. (453.6 kg)CERCLA RQ –
WARNING: This product contains a chemical known to the State of California to cause cancer. WARNING: This product
contains less than 1% of a chemical known to the State of California to cause birth defects or other reproductive harm.
Section 16. Other information
History
Date of issue
Version
Date of previous issue
:
:
:
07/17/2017
Not applicable.
1.0
1
3
2
National Fire Protection Association (U.S.A.)
Health
Special
Instability/Reactivity
Flammability
Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency Response Copyright 1997, National Fire Protection Association, Quincy, MA 02269. This
reprinted material is not the complete and official position of the National Fire Protection Association, on the referenced subject which is represented only by the standard in its entirety.
Copyright 2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to be interpreted and applied only by properly trained individuals to identify fire, health and
reactivity hazards of chemicals. The user is referred to certain limited number of chemicals with recommended classifications in NFPA 49 and NFPA 325, which would be used as a guideline only.
Whether the chemicals are classified by NFPA or not, anyone using the 704 systems to classify chemicals does so at their own risk.
AOC Corporate Regulatory Affairs
Page: 9 of 10G730AA70812
Section 16. Other information
The information contained in this data sheet is furnished in good faith and without warranty, representation, or inducement or license of any kind,
except that it is accurate to the best of AOC, LLC’s knowledge, or was obtained from sources believed by AOC, LLC to be reliable. The
accuracy, adequacy or completeness of health and safety precautions set forth herein cannot be guaranteed, and the buyer is solely
responsible for ensuring that the product is used, handled, stored, and disposed of safely and in compliance with applicable federal, state or
provincial, and local laws. AOC, LLC disclaims liability for any loss, damage or personal injury that arises from, or is in any way related to, use
of the information contained in this data sheet.
Notice to reader
Indicates information that has changed from previously issued version.
Key to abbreviations :ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by
the Protocol of 1978. (“Marpol” = marine pollution)
UN = United Nations
This Safety Data Sheet (SDS) and its content are the confidential and proprietary information of AOC and it may not be modified, altered,
deconstructed, or presented in any other manner, without the explicit authorization of AOC and/or its legal counsel.
Page: 10 of 10G730AA70812
by | Sep 27, 2025
Gel Coat
Product name
Product type
Emergency telephone number
Section 1. Identification
Chemical family Aromatic.
Supplier’s details AOC, LLC
955 Highway 57 East
Collierville, TN 38017
E-Mail: aoc.sds@aoc-resins.com
Website: www.aoc-resins.com
Phone Number: (901) 854-2800
Hours: 8AM-5pm (Central Time) Monday-Friday
Relevant identified uses of the substance or mixture and uses advised against
SDS No. NA-1509:3014 (Version: 2.0)
Uses advised against
Identified uses Used in the manufacture of thermoset plastic parts.
No additional information.
G130LQ71196
CHEMTREC Within USA and Canada
CHEMTREC Outside USA and Canada
CANUTEC Within Canada
+1 (800) 424-9300
+1 (703) 527-3887
+1 (613) 996-6666
CCN1023
SAFETY DATA SHEET
Date of issue: 02/01/2017
Date of previous issue: 09/30/2015
Section 2. Hazards identification
OSHA/HCS status
FLAMMABLE LIQUIDS Category 3 H226
SKIN CORROSION/IRRITATION Category 2 H315
SERIOUS EYE DAMAGE/ EYE IRRITATION Category 2 H319
ACUTE TOXICITY (INHALATION) Category 4 H332
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) Category 3 H335
REPRODUCTIVE TOXICITY Category 2 H361d
CARCINOGENICITY Category 2 H351
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) Category 1 H372
ASPIRATION HAZARD Category 1 H304
Classification of the substance or mixture
Signal word
Danger
Hazard statements
H226: Flammable liquid and vapor.
H332: Harmful if inhaled.
H361d: Suspected of damaging the unborn child.
H351: Suspected of causing cancer.
H319: Causes serious eye irritation.
H315: Causes skin irritation.
H335: May cause respiratory irritation.
H372: Causes damage to organs through prolonged or repeated exposure if inhaled.
H304: May be fatal if swallowed and enters airways.
Hazard pictograms
GHS label elements
This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Page: 1 of 10G130LQ71196
Section 2. Hazards identification
Precautionary statements
Prevention
P210: Keep away from heat, sparks, open flames and hot surfaces. – No smoking.
P233: Keep container tightly closed.
P240: Ground/bond container and receiving equipment.
P241: Use explosion-proof electrical/ventilating/lighting/material-handling equipment.
P242: Use only non-sparking tools.
P243: Take precautionary measures against static discharge.
P201: Obtain special instructions before use.
P202: Do not handle until all safety precautions have been read and understood.
P264: Wash hands thoroughly after handling.
P270: Do not eat, drink or smoke when using this product.
P271: Use only outdoors or in a well-ventilated area.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P260: Do not breathe vapor or mist.
Response
P370+P378: In case of fire: Use dry chemical, CO , water spray (fog) or foam.
P301+P310: IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.
P331: Do NOT induce vomiting.
P308+P313: IF exposed or concerned: Get medical advice/attention.
P304+P340: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P312: Call a POISON CENTER or physician if you feel unwell.
P303+P361+P353: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower.
P332+P313: If skin irritation occurs, get medical advice/attention.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing.
P337+P313: If eye irritation persists, get medical advice/attention.
P308+P311: IF exposed or concerned: Call a POISON CENTER or doctor/physician.
P391: Collect spillage.
Storage
P403 + P235: Store in a well-ventilated place. Keep cool.
P233: Keep container tightly closed.
P405: Store locked up.
Disposal
P501: Dispose of contents and container in accordance with all local, regional, national and international regulations.
General
P101: If medical advice is needed, have product container or label at hand.
P102: Keep out of reach of children.
Hazards not otherwise classified
None known.
Section 3. Composition/information on ingredients
Ingredient name CAS number %
There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are
classified as hazardous to health or the environment and hence require reporting in this section.
Substance/mixture :
Occupational exposure limits, if available, are listed in Section 8.
Mixture.
Styrene 100-42-5 27.7
Carbon Black 1333-86-4 1
Cobalt 2-Ethylhexanoate 136-52-7 0.3
Petroleum Naphtha 64742-95-6 0.3
N,N-Dimethylaniline 121-69-7 0.3
Page: 2 of 10G130LQ71196
Wash out mouth with water. Remove dentures if any. Stop if the exposed person feels sick as vomiting may be dangerous. Do
not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit
does not enter the lungs. Seek immediate medical attention.
Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Use of
buffered baby shampoo will aid in removal. If irritation persists, get medical attention.
In case of contact, immediately flush skin with plenty of water. Remove contaminated clothing and shoes. If irritation persists,
seek medical attention. Wash contaminated clothing before reuse. Clean shoes thoroughly before reuse.
Move the victim to a safe area as soon as possible. Allow the victim to rest in a well-ventilated area. If breathing is difficult, give
oxygen. If the victim is not breathing, perform mouth-to-mouth resuscitation. Seek immediate medical attention.
Section 4. First aid measures
Eye contact
Skin contact
Inhalation
Ingestion
Notes to physician
Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.
Description of necessary first aid measures
Most important symptoms/effects, acute and delayed
See toxicological information (Section 11)
Indication of immediate medical attention and special treatment needed, if necessary
Irritating to mouth, throat and stomach.
Causes serious eye irritation.
Causes skin irritation.
Harmful if inhaled. May cause respiratory irritation.
Eye contact
Skin contact
Inhalation
Ingestion
Over-exposure signs/symptoms
Eye contact
Inhalation
Skin contact
Ingestion
Adverse symptoms may include the following: pain or irritation, watering, redness.
Adverse symptoms may include the following: respiratory tract irritation, coughing.
Adverse symptoms may include the following: irritation, redness.
Adverse symptoms may include the following: Irritating to mouth, throat and stomach..
Section 5. Fire-fighting measures
Fire water contaminated with this material must be contained and prevented from being discharged to any waterway, sewer or
drain.
Hazardous thermal decomposition products
Specific hazards arising from the chemical
Decomposition products may include the following materials: carbon dioxide, carbon monoxide, sulfur oxides halogenated
compounds, metal oxide/oxides
Flammable liquid and vapor. In a fire or if heated, a pressure increase will occur and the container may burst, with the risk of a
subsequent explosion. The vapor/gas is heavier than air and will spread along the ground. Vapors may accumulate in low or
confined areas or travel a considerable distance to a source of ignition and flash back. Runoff to sewer may create fire or
explosion hazard. This material is harmful to aquatic life with long lasting effects. Fire water contaminated with this material must
be contained and prevented from being discharged to any waterway, sewer or drain.
Special protective equipment for fire-fighters
Use dry chemical, CO , water spray (fog) or foam.
Extinguishing media
Do not use water jet.
Suitable extinguishing media
Unsuitable extinguishing media
Special protective actions for fire-fighters
Page: 3 of 10G130LQ71196
Section 5. Fire-fighting measures
Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece
operated in positive pressure mode.
Section 6. Accidental release measures
Environmental precautions
Personal precautions, protective equipment and emergency procedures
Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water
courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and
collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in
container for disposal according to local regulations (see Section 13). Use spark-proof tools and explosion-proof equipment.
Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled
product. Note: see Section 1 for emergency contact information and Section 13 for waste disposal.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities
if the product has caused environmental pollution (sewers, waterways, soil or air). Water polluting material. May be harmful to
the environment if released in large quantities.
Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-
insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Use spark-proof tools and
explosion-proof equipment. Dispose of via a licensed waste disposal contractor.
Methods and materials for containment and cleaning up
For non-emergency personnel
For emergency responders
No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Do not touch or
walk through spilled material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Avoid breathing vapor or
mist. Provide adequate ventilation.
If specialised clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable
materials. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. See
also the information in “For non-emergency personnel”.
Small spill
Large spill
Section 7. Handling and storage
Advice on general occupational hygiene
Conditions for safe storage, including any incompatibilities
Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers
should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment
before entering eating areas. See also Section 8 for additional information on hygiene measures.
Store in accordance with local regulations. Store in a segregated and approved area. Store in original container protected from
direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink.
Eliminate all ignition sources. Segregate from oxidizing materials. Keep container tightly closed and sealed until ready for use.
Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled
containers. Use appropriate containment to avoid environmental contamination. Refer to the product label and/or technical data
sheet for further information.
Protective measures
Put on appropriate personal protective equipment (see Section 8). Eating, drinking and smoking should be prohibited in areas
where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking.
Remove contaminated clothing and protective equipment before entering eating areas. Do not breathe vapor or mist. Do not
ingest. Avoid contact with eyes, skin and clothing. Avoid release to the environment. Use only with adequate ventilation. Wear
appropriate respirator when ventilation is inadequate. Do not enter storage areas and confined spaces unless adequately
ventilated. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when
not in use. Store and use away from heat, sparks, open flame or any other ignition source. Use explosion-proof electrical
(ventilating, lighting and material handling) equipment. Use only non-sparking tools. Take precautionary measures against
electrostatic discharges. Empty containers retain product residue and can be hazardous. Do not reuse container.
Precautions for safe handling
Page: 4 of 10G130LQ71196
Styrene ACGIH TLV (United States, 3/2015).
TWA: 20 ppm 8 hours.
TWA: 85 mg/m 8 hours.
STEL: 40 ppm 15 minutes.
STEL: 170 mg/m 15 minutes.
OSHA PEL Z2 (United States, 2/2013).
TWA: 100 ppm 8 hours.
CEIL: 200 ppm
AMP: 600 ppm 5 minutes.
NIOSH REL (United States, 10/2013).
TWA: 50 ppm 10 hours.
TWA: 215 mg/m 10 hours.
STEL: 100 ppm 15 minutes.
STEL: 425 mg/m 15 minutes.
Carbon Black NIOSH REL (United States, 6/2009).
TWA: 3.5 mg/m 10 hours.
TWA: 0.1 mg of PAHs/cm 10 hours.
OSHA PEL (United States, 6/2010).
TWA: 3.5 mg/m 8 hours. Form:
ACGIH TLV (United States, 3/2012).
TWA: 3 mg/m 8 hours. Form: Inhalable fraction
Cobalt 2-Ethylhexanoate OSHA PEL (United States).
TWA: 0.1 mg/m
ACGIH TLV (United States, 3/2015).
TWA: 0.02 mg/m , (as Co) 8 hours.
N,N-Dimethylaniline ACGIH TLV (United States, 3/2015). Absorbed through skin.
TWA: 5 ppm 8 hours.
TWA: 25 mg/m 8 hours.
STEL: 10 ppm 15 minutes.
STEL: 50 mg/m 15 minutes.
NIOSH REL (United States, 10/2013). Absorbed through skin.
TWA: 5 ppm 10 hours.
TWA: 25 mg/m 10 hours.
STEL: 10 ppm 15 minutes.
STEL: 50 mg/m 15 minutes.
OSHA PEL (United States, 2/2013). Absorbed through skin.
TWA: 5 ppm 8 hours.
TWA: 25 mg/m 8 hours.
Section 8. Exposure controls/personal protection
Ingredient name Exposure limits
Hand protection
Use a properly fitted, air-purifying or air-fed respirator complying with an approved standard if a risk assessment indicates this is
necessary. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe
working limits of the selected respirator.
Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical
products if a risk assessment indicates this is necessary.
Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid
exposure to liquid splashes, mists or dusts.
Eye/face protection
Respiratory protection
Body protection
Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should
be approved by a specialist before handling this product.
Appropriate engineering controls
Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or other engineering controls to keep
worker exposure to airborne contaminants below any recommended or statutory limits. The engineering controls also need
to keep gas, vapor or dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment.
Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at
the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Ensure that
eyewash stations and safety showers are close to the workstation location.
Hygiene measures
Control parameters
Individual protection measures
Occupational exposure limits
Other skin protection
Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the
risks involved and should be approved by a specialist before handling this product.
Page: 5 of 10G130LQ71196
Section 8. Exposure controls/personal protection
Section 9. Physical and chemical properties
Physical state
Melting point
Vapor pressure
Relative density
Vapor density
Solubility
Liquid.
-23.8 F / -30.6 C (Styrene)
1.1 to 1.4 (Water = 1)
3.6 (Air = 1) (Styrene )
5.0 mm Hg@ 68 F / 20 C (Styrene)
Slight.
Aromatic.Odor
pH
Grey.Color
Evaporation rate < 1 (Butyl acetate = 1)
Auto-ignition temperature
Flash point
914 F / 490 C (Styrene)
88 F / 31 C (Styrene)
Not available.
Not applicable.
Viscosity Not available.
0.01 - 0.1 ppm (Styrene)Odor threshold
Partition coefficient: n-octanol/water
Appearance
Boiling point 293 F / 145 C (Styrene)
Flammability (solid, gas) Not applicable.
Lower and upper explosive (flammable) limits Lower: 1.1% Upper: 6.1% (Styrene)
Molecular weight Not available.
Decomposition temperature Not available.
Section 10. Stability and reactivity
Hazardous decomposition products
Conditions to avoid
Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld, braze, solder, drill, grind or expose
containers to heat or sources of ignition.
Under normal conditions of storage and use, hazardous decomposition products should not be produced.
The product is stable. Stable under recommended storage and handling conditions (see Section 7).
Chemical stability
Reactive or incompatible with the following materials: oxidizing materials
Incompatible materials
Possibility of hazardous reactions
Under normal conditions of storage and use, hazardous reactions will not occur.
Reactivity
No specific test data related to reactivity available for this product or its ingredients.
Section 11. Toxicological information
Acute toxicity
Styrene LC50 Inhalation Gas. Rat 2770 ppm 4 hours
LC50 Inhalation Vapor Rat 11800 mg/m 4 hours
LD50 Oral Rat 2650 mg/kg -
Carbon Black LC50 Inhalation Dusts and mists Rat 6750 mg/m 4 hours
LD50 Dermal Rabbit >3000 mg/kg –
LD50 Oral Rat >15400 mg/kg –
LD50 Oral Rat >15400 mg/kg –
Cobalt 2-Ethylhexanoate LD50 Dermal Rabbit >5 g/kg –
LD50 Oral Rat 1.22 g/kg –
LD50 Oral Rat 6171 mg/kg –
Petroleum Naphtha LD50 Oral Rat 8400 mg/kg –
N,N-Dimethylaniline LD50 Dermal Rabbit 1770 mg/kg –
Product/ingredient name Result Species Dose Exposure
Information on toxicological effects
Page: 6 of 10G130LQ71196
Section 11. Toxicological information
LD50 Oral Rat 1120 mg/kg –
Carcinogenicity
Mutagenicity
Teratogenicity
Reproductive toxicity
Irritation/Corrosion
Styrene Eyes – Mild irritant Human – 50 parts per
million
–
Eyes – Moderate irritant Rabbit – 24 hours 100
milligrams
–
Eyes – Severe irritant Rabbit – 100 milligrams-
Skin – Mild irritant Rabbit – 500 milligrams-
Skin – Moderate irritant Rabbit – 100 Percent –
N,N-Dimethylaniline Eyes – Moderate irritant Rabbit – 24 hours 20
milligrams
–
Eyes – Moderate irritant Rabbit – 20 milligrams –
Skin – Mild irritant Rabbit – 24 hours 500
milligrams
–
Skin – Mild irritant Rabbit – 500 milligrams-
Product/ingredient name Result Score Exposure Observation
Sensitization
Species
Inhalation
Harmful if inhaled. May cause respiratory irritation.
Irritating to mouth, throat and stomach.
Ingestion
Skin contact
Causes skin irritation.
Causes serious eye irritation.
Eye contact
Symptoms related to the physical, chemical and toxicological characteristics
Adverse symptoms may include the following: respiratory tract irritation, coughing.
Eye contact
Adverse symptoms may include the following: pain or irritation, watering, redness.
Specific target organ toxicity (single exposure)
Specific target organ toxicity (repeated exposure)
Aspiration hazard
Potential acute health effects
Classification
Styrene – 2B Reasonably anticipated to be a human carcinogen.
Carbon Black – 2B –
Cobalt 2-Ethylhexanoate – 2B –
N,N-Dimethylaniline – 3 –
Product/ingredient name NTPIARCACGIH
May cause sensitization by skin contact.
No mutagenic effect.
1) Negative Study A published study concluded that the mechanism for producing cancer in mice exposed to styrene
is not applicable in human metabolism. (June 2013 Pharmacology & Toxicology 66 (2013))
2) Negative Study A recent update to an extensive study of reinforced plastic workers from 1948-1977 concluded that
there was no coherent evidence that styrene exposure increased risk of cancer (March 2013 Epidemiology Vol. 24
Issue 2)
3) Positive Study Styrene induced pulmonary toxicity and carcinogenicity in mice was shown to be caused by a
metabolite of styrene, probably styrene oxide. (Dec.2001 Toxicology Vol.169 Issue 2)
Not considered to be toxic to the reproductive system.
No known effect according to our database..
No known effect according to our database.
A study of long term effects of workers exposed to styrene levels in the range of 25-35 ppm, 8 hour TWA, indicated a
possible mild hearing loss.
No known effect according to our database.
Inhalation
Page: 7 of 10G130LQ71196
Section 11. Toxicological information
Skin contact
Ingestion
Adverse symptoms may include the following: Irritating to mouth, throat and stomach..
Adverse symptoms may include the following: irritation, redness.
Section 12. Ecological information
LogPow BCF Potential
Bioaccumulative potential
Other adverse effects
No known effect according to our database.
Product/ingredient name
Styrene 2.95 13.49 low
N,N-Dimethylaniline 2.31 7.943282347 low
Product/ingredient name Aquatic half-life Photolysis Biodegradability
Styrene – – Readily
Toxicity
Styrene Acute EC50 4.7 mg/l Fresh water Daphnia – Daphnia magna 48 hours
Acute LC50 4.02 mg/l Fresh water Fish – Pimephales promelas 96 hours
N,N-Dimethylaniline Acute EC50 22000 g/l Fresh water Algae – Chlorella pyrenoidosa 72 hours
Acute EC50 2.3 mg/l Fresh water Daphnia – Daphnia magna 48 hours
Acute LC50 52600 g/l Fresh water Fish – Pimephales promelas 96 hours
Chronic NOEC 14000 g/l Fresh water Algae – Chlorella pyrenoidosa 72 hours
Product/ingredient name SpeciesResult Exposure
Persistence and degradability
Styrene EU 100 % – Readily – 1 days – –
Product/ingredient name Test DoseResult Inoculum
Soil/water partition coefficient (KOC)
Not available.
Mobility in soil
Section 13. Disposal considerations
The generation of waste should be avoided or minimized wherever possible. Empty containers or liners may retain some
product residues. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Disposal of
this product, solutions and any by-products should at all times comply with the requirements of environmental protection
and waste disposal legislation and any regional local authority requirements. Avoid disposal. Attempt to use product
completely in accordance with intended use. Waste packaging should be recycled. Incineration or landfill should only be
considered when recycling is not feasible.
Disposal methods
The information in this section contains generic advice and guidance. The list of Identified Uses in Section 1 should be consulted for any available use-specific information
provided in the Exposure Scenario(s).
Special precautions
This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers
that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Do not cut, weld
or grind used containers unless they have been cleaned thoroughly internally. Avoid dispersal of spilled material and runoff
and contact with soil, waterways, drains and sewers.
Section 14. Transport information
Resin Solution
3
UN1866UN number
Proper shipping name
Transport hazard class(es)
DOT / TDG/ IMDG/IMO / ICAO/IATA and National regulations.
Page: 8 of 10G130LQ71196
Section 14. Transport information
IIIPacking group
Additional information US regulations require the reporting of spills when the amount exceeds the Reportable
Quantity (RQ) for specific components of this material. See CERCLA in Section 15,
Regulatory Information, for the Reportable Quantities.
Environmental hazards Marine pollutant: No.
Special precautions for user Transport within user s premises: always transport in closed containers that are upright
and secure. Ensure that persons transporting the product know what to do in the event of
an accident or spillage.
IMDGEmergency schedules (EmS): F-E, S-E
Remarks: FP-31 C
IATANo additional information.
Section 15. Regulatory information
Inventories (National and International)
:All components are listed or exempted.
SARA 313
Product name
Styrene 100-42-5
Cobalt 2-Ethylhexanoate 136-52-7
Form R – Reporting
requirements
SARA 311/312
Styrene Yes. No. No. No. Yes.
Carbon Black No. No. No. No. Yes.
Cobalt 2-Ethylhexanoate No. No. No. Yes. Yes.
Petroleum Naphtha Yes. No. No. Yes. Yes.
N,N-Dimethylaniline Yes. No. No. Yes. Yes.
Name Fire
hazard
Sudden
release of
pressure
Reactive Immediate
(acute)
health hazard
Delayed
(chronic)
health hazard
Composition/information on ingredients
United States inventory (TSCA 8b)
Australia (AICS) :Not determined.
Canada (DSL) :At least one component is not listed in DSL but all such components are listed in NDSL.
China (IECSC) :All components are listed or exempted.
Europe (EINECS) :Not determined.
Japan (ENCS) :Japan inventory (ENCS): Not determined.
Japan inventory (ISHL): Not determined.
Republic of Korea (KECI) :Not determined.
Malaysia (EHS Register) :Not determined.
New Zealand (NZIoC) :Not determined.
Philippines (PICCS) :Not determined.
Taiwan (CSNN) :Not determined.
CAS number
WARNING: This product contains a chemical known to the State of California to cause cancer.
WARNING: This product contains less than 1% of a chemical known to the State of California to cause birth defects or other reproductive
harm.
California Prop. 65
State regulations
Styrene – 1000 lbs. (453.6 kg)CERCLA RQ –
Page: 9 of 10G130LQ71196
Section 16. Other information
History
Date of issue
Version
The information contained in this data sheet is furnished in good faith and without warranty, representation, or inducement or license of any kind,
except that it is accurate to the best of AOC, LLC’s knowledge, or was obtained from sources believed by AOC, LLC to be reliable. The
accuracy, adequacy or completeness of health and safety precautions set forth herein cannot be guaranteed, and the buyer is solely
responsible for ensuring that the product is used, handled, stored, and disposed of safely and in compliance with applicable federal, state or
provincial, and local laws. AOC, LLC disclaims liability for any loss, damage or personal injury that arises from, or is in any way related to, use
of the information contained in this data sheet.
Notice to reader
Date of previous issue
:
:
:
Indicates information that has changed from previously issued version.
Key to abbreviations :ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by
the Protocol of 1978. (“Marpol” = marine pollution)
UN = United Nations
02/01/2017
09/30/2015
2.0
1
3
2
National Fire Protection Association (U.S.A.)
Health
Special
Instability/Reactivity
Flammability
Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency Response Copyright 1997, National Fire Protection Association, Quincy, MA 02269. This
reprinted material is not the complete and official position of the National Fire Protection Association, on the referenced subject which is represented only by the standard in its entirety.
Copyright 2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to be interpreted and applied only by properly trained individuals to identify fire, health and
reactivity hazards of chemicals. The user is referred to certain limited number of chemicals with recommended classifications in NFPA 49 and NFPA 325, which would be used as a guideline only.
Whether the chemicals are classified by NFPA or not, anyone using the 704 systems to classify chemicals does so at their own risk.
AOC Corporate Regulatory Affairs
This Safety Data Sheet (SDS) and its content are the confidential and proprietary information of AOC and it may not be modified, altered,
deconstructed, or presented in any other manner, without the explicit authorization of AOC and/or its legal counsel.
Page: 10 of 10G130LQ71196
by | Sep 27, 2025
by | Sep 27, 2025
Gel Coat
Product name
Product type
Emergency telephone number
Section 1. Identification
Chemical family Aromatic.
Supplier’s details AOC, LLC
955 Highway 57 East
Collierville, TN 38017
E-Mail: aoc.sds@aoc-resins.com
Website: www.aoc-resins.com
Phone Number: (901) 854-2800
Hours: 8AM-5pm (Central Time) Monday-Friday
Relevant identified uses of the substance or mixture and uses advised against
SDS No. NA1504:1231 (Version: 2.0)
Uses advised against
Identified uses Used in the manufacture of thermoset plastic parts.
No additional information.
G130LN71196
CHEMTREC Within USA and Canada
CHEMTREC Outside USA and Canada
CANUTEC Within Canada
+1 (800) 424-9300
+1 (703) 527-3887
+1 (613) 996-6666
CCN1023
SAFETY DATA SHEET
Date of issue: 02/01/2017
Date of previous issue: 05/26/2015
Section 2. Hazards identification
OSHA/HCS status
FLAMMABLE LIQUIDS Category 3 H226
SKIN CORROSION/IRRITATION Category 2 H315
SERIOUS EYE DAMAGE/ EYE IRRITATION Category 2 H319
ACUTE TOXICITY (INHALATION) Category 4 H332
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) Category 3 H335
REPRODUCTIVE TOXICITY Category 2 H361d
CARCINOGENICITY Category 2 H351
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) Category 1 H372
ASPIRATION HAZARD Category 1 H304
Classification of the substance or mixture
Signal word
Danger
Hazard statements
H226: Flammable liquid and vapor.
H332: Harmful if inhaled.
H361d: Suspected of damaging the unborn child.
H351: Suspected of causing cancer.
H319: Causes serious eye irritation.
H315: Causes skin irritation.
H335: May cause respiratory irritation.
H372: Causes damage to organs through prolonged or repeated exposure if inhaled.
H304: May be fatal if swallowed and enters airways.
Hazard pictograms
GHS label elements
This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Page: 1 of 10G130LN71196
Section 2. Hazards identification
Precautionary statements
Prevention
P210: Keep away from heat, sparks, open flames and hot surfaces. – No smoking.
P233: Keep container tightly closed.
P240: Ground/bond container and receiving equipment.
P241: Use explosion-proof electrical/ventilating/lighting/material-handling equipment.
P242: Use only non-sparking tools.
P243: Take precautionary measures against static discharge.
P201: Obtain special instructions before use.
P202: Do not handle until all safety precautions have been read and understood.
P264: Wash hands thoroughly after handling.
P270: Do not eat, drink or smoke when using this product.
P271: Use only outdoors or in a well-ventilated area.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P260: Do not breathe vapor or mist.
Response
P370+P378: In case of fire: Use dry chemical, CO , water spray (fog) or foam.
P301+P310: IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.
P331: Do NOT induce vomiting.
P308+P313: IF exposed or concerned: Get medical advice/attention.
P304+P340: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P312: Call a POISON CENTER or physician if you feel unwell.
P303+P361+P353: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower.
P332+P313: If skin irritation occurs, get medical advice/attention.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing.
P337+P313: If eye irritation persists, get medical advice/attention.
P308+P311: IF exposed or concerned: Call a POISON CENTER or doctor/physician.
P391: Collect spillage.
Storage
P403 + P235: Store in a well-ventilated place. Keep cool.
P233: Keep container tightly closed.
P405: Store locked up.
Disposal
P501: Dispose of contents and container in accordance with all local, regional, national and international regulations.
General
P101: If medical advice is needed, have product container or label at hand.
P102: Keep out of reach of children.
Hazards not otherwise classified
None known.
Section 3. Composition/information on ingredients
Ingredient name CAS number %
There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are
classified as hazardous to health or the environment and hence require reporting in this section.
Substance/mixture :
Occupational exposure limits, if available, are listed in Section 8.
Mixture.
Styrene 100-42-5 34.8
Carbon Black 1333-86-4 1
Petroleum Naphtha 64742-95-6 0.3
Cobalt 2-Ethylhexanoate 136-52-7 0.3
Page: 2 of 10G130LN71196
Wash out mouth with water. Remove dentures if any. Stop if the exposed person feels sick as vomiting may be dangerous. Do
not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit
does not enter the lungs. Seek immediate medical attention.
Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Use of
buffered baby shampoo will aid in removal. If irritation persists, get medical attention.
In case of contact, immediately flush skin with plenty of water. Remove contaminated clothing and shoes. If irritation persists,
seek medical attention. Wash contaminated clothing before reuse. Clean shoes thoroughly before reuse.
Move the victim to a safe area as soon as possible. Allow the victim to rest in a well-ventilated area. If breathing is difficult, give
oxygen. If the victim is not breathing, perform mouth-to-mouth resuscitation. Seek immediate medical attention.
Section 4. First aid measures
Eye contact
Skin contact
Inhalation
Ingestion
Notes to physician
Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.
Description of necessary first aid measures
Most important symptoms/effects, acute and delayed
See toxicological information (Section 11)
Indication of immediate medical attention and special treatment needed, if necessary
Irritating to mouth, throat and stomach.
Causes serious eye irritation.
Causes skin irritation.
Harmful if inhaled. May cause respiratory irritation.
Eye contact
Skin contact
Inhalation
Ingestion
Over-exposure signs/symptoms
Eye contact
Inhalation
Skin contact
Ingestion
Adverse symptoms may include the following: pain or irritation, watering, redness.
Adverse symptoms may include the following: respiratory tract irritation, coughing.
Adverse symptoms may include the following: irritation, redness.
Adverse symptoms may include the following: Irritating to mouth, throat and stomach..
Section 5. Fire-fighting measures
Fire water contaminated with this material must be contained and prevented from being discharged to any waterway, sewer or
drain.
Hazardous thermal decomposition products
Specific hazards arising from the chemical
Decomposition products may include the following materials: carbon dioxide, carbon monoxide, sulfur oxides halogenated
compounds, metal oxide/oxides
Flammable liquid and vapor. In a fire or if heated, a pressure increase will occur and the container may burst, with the risk of a
subsequent explosion. The vapor/gas is heavier than air and will spread along the ground. Vapors may accumulate in low or
confined areas or travel a considerable distance to a source of ignition and flash back. Runoff to sewer may create fire or
explosion hazard. This material is harmful to aquatic life with long lasting effects. Fire water contaminated with this material must
be contained and prevented from being discharged to any waterway, sewer or drain.
Special protective equipment for fire-fighters
Use dry chemical, CO , water spray (fog) or foam.
Extinguishing media
Do not use water jet.
Suitable extinguishing media
Unsuitable extinguishing media
Special protective actions for fire-fighters
Page: 3 of 10G130LN71196
Section 5. Fire-fighting measures
Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece
operated in positive pressure mode.
Section 6. Accidental release measures
Environmental precautions
Personal precautions, protective equipment and emergency procedures
Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water
courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and
collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in
container for disposal according to local regulations (see Section 13). Use spark-proof tools and explosion-proof equipment.
Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled
product. Note: see Section 1 for emergency contact information and Section 13 for waste disposal.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities
if the product has caused environmental pollution (sewers, waterways, soil or air). Water polluting material. May be harmful to
the environment if released in large quantities.
Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-
insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Use spark-proof tools and
explosion-proof equipment. Dispose of via a licensed waste disposal contractor.
Methods and materials for containment and cleaning up
For non-emergency personnel
For emergency responders
No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Do not touch or
walk through spilled material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Avoid breathing vapor or
mist. Provide adequate ventilation.
If specialised clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable
materials. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. See
also the information in “For non-emergency personnel”.
Small spill
Large spill
Section 7. Handling and storage
Advice on general occupational hygiene
Conditions for safe storage, including any incompatibilities
Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers
should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment
before entering eating areas. See also Section 8 for additional information on hygiene measures.
Store in accordance with local regulations. Store in a segregated and approved area. Store in original container protected from
direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink.
Eliminate all ignition sources. Segregate from oxidizing materials. Keep container tightly closed and sealed until ready for use.
Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled
containers. Use appropriate containment to avoid environmental contamination. Refer to the product label and/or technical data
sheet for further information.
Protective measures
Put on appropriate personal protective equipment (see Section 8). Eating, drinking and smoking should be prohibited in areas
where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking.
Remove contaminated clothing and protective equipment before entering eating areas. Do not breathe vapor or mist. Do not
ingest. Avoid contact with eyes, skin and clothing. Avoid release to the environment. Use only with adequate ventilation. Wear
appropriate respirator when ventilation is inadequate. Do not enter storage areas and confined spaces unless adequately
ventilated. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when
not in use. Store and use away from heat, sparks, open flame or any other ignition source. Use explosion-proof electrical
(ventilating, lighting and material handling) equipment. Use only non-sparking tools. Take precautionary measures against
electrostatic discharges. Empty containers retain product residue and can be hazardous. Do not reuse container.
Precautions for safe handling
Page: 4 of 10G130LN71196
Styrene ACGIH TLV (United States, 3/2015).
TWA: 20 ppm 8 hours.
TWA: 85 mg/m 8 hours.
STEL: 40 ppm 15 minutes.
STEL: 170 mg/m 15 minutes.
OSHA PEL Z2 (United States, 2/2013).
TWA: 100 ppm 8 hours.
CEIL: 200 ppm
AMP: 600 ppm 5 minutes.
NIOSH REL (United States, 10/2013).
TWA: 50 ppm 10 hours.
TWA: 215 mg/m 10 hours.
STEL: 100 ppm 15 minutes.
STEL: 425 mg/m 15 minutes.
Carbon Black NIOSH REL (United States, 6/2009).
TWA: 3.5 mg/m 10 hours.
TWA: 0.1 mg of PAHs/cm 10 hours.
OSHA PEL (United States, 6/2010).
TWA: 3.5 mg/m 8 hours. Form:
ACGIH TLV (United States, 3/2012).
TWA: 3 mg/m 8 hours. Form: Inhalable fraction
Cobalt 2-Ethylhexanoate OSHA PEL (United States).
TWA: 0.1 mg/m
ACGIH TLV (United States, 3/2015).
TWA: 0.02 mg/m , (as Co) 8 hours.
Section 8. Exposure controls/personal protection
Ingredient name Exposure limits
Hand protection
Use a properly fitted, air-purifying or air-fed respirator complying with an approved standard if a risk assessment indicates this is
necessary. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe
working limits of the selected respirator.
Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical
products if a risk assessment indicates this is necessary.
Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid
exposure to liquid splashes, mists or dusts.
Eye/face protection
Respiratory protection
Body protection
Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should
be approved by a specialist before handling this product.
Appropriate engineering controls
Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or other engineering controls to keep
worker exposure to airborne contaminants below any recommended or statutory limits. The engineering controls also need
to keep gas, vapor or dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment.
Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at
the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Ensure that
eyewash stations and safety showers are close to the workstation location.
Hygiene measures
Control parameters
Individual protection measures
Occupational exposure limits
Other skin protection
Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the
risks involved and should be approved by a specialist before handling this product.
Page: 5 of 10G130LN71196
Section 9. Physical and chemical properties
Physical state
Melting point
Vapor pressure
Relative density
Vapor density
Solubility
Liquid.
-23.8 F / -30.6 C (Styrene)
1.1 to 1.4 (Water = 1)
3.6 (Air = 1) (Styrene )
5.0 mm Hg@ 68 F / 20 C (Styrene)
Slight.
Aromatic.Odor
pH
Grey.Color
Evaporation rate < 1 (Butyl acetate = 1)
Auto-ignition temperature
Flash point
914 F / 490 C (Styrene)
88 F / 31 C (Styrene)
Not available.
Not applicable.
Viscosity Not available.
0.01 - 0.1 ppm (Styrene)Odor threshold
Partition coefficient: n-octanol/water
Appearance
Boiling point 293 F / 145 C (Styrene)
Flammability (solid, gas) Not applicable.
Lower and upper explosive (flammable) limits Lower: 1.1% Upper: 6.1% (Styrene)
Molecular weight Not available.
Decomposition temperature Not available.
Section 10. Stability and reactivity
Hazardous decomposition products
Conditions to avoid
Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld, braze, solder, drill, grind or expose
containers to heat or sources of ignition.
Under normal conditions of storage and use, hazardous decomposition products should not be produced.
The product is stable. Stable under recommended storage and handling conditions (see Section 7).
Chemical stability
Reactive or incompatible with the following materials: oxidizing materials
Incompatible materials
Possibility of hazardous reactions
Under normal conditions of storage and use, hazardous reactions will not occur.
Reactivity
No specific test data related to reactivity available for this product or its ingredients.
Section 11. Toxicological information
Acute toxicity
Styrene LC50 Inhalation Gas. Rat 2770 ppm 4 hours
LC50 Inhalation Vapor Rat 11800 mg/m 4 hours
LD50 Oral Rat 2650 mg/kg -
Carbon Black LC50 Inhalation Dusts and mists Rat 6750 mg/m 4 hours
LD50 Dermal Rabbit >3000 mg/kg –
LD50 Oral Rat >15400 mg/kg –
LD50 Oral Rat >15400 mg/kg –
Petroleum Naphtha LD50 Oral Rat 8400 mg/kg –
Cobalt 2-Ethylhexanoate LD50 Dermal Rabbit >5 g/kg –
LD50 Oral Rat 1.22 g/kg –
LD50 Oral Rat 6171 mg/kg –
Product/ingredient name Result Species Dose Exposure
Irritation/Corrosion
Information on toxicological effects
Page: 6 of 10G130LN71196
Section 11. Toxicological information
Carcinogenicity
Mutagenicity
Teratogenicity
Reproductive toxicity
Styrene Eyes – Mild irritant Human – 50 parts per
million
–
Eyes – Moderate irritant Rabbit – 24 hours 100
milligrams
–
Eyes – Severe irritant Rabbit – 100 milligrams-
Skin – Mild irritant Rabbit – 500 milligrams-
Skin – Moderate irritant Rabbit – 100 Percent –
Product/ingredient name Result Score Exposure Observation
Sensitization
Species
Inhalation
Harmful if inhaled. May cause respiratory irritation.
Irritating to mouth, throat and stomach.
Ingestion
Skin contact
Causes skin irritation.
Causes serious eye irritation.
Eye contact
Symptoms related to the physical, chemical and toxicological characteristics
Skin contact
Ingestion
Adverse symptoms may include the following: respiratory tract irritation, coughing.
Adverse symptoms may include the following: Irritating to mouth, throat and stomach..
Adverse symptoms may include the following: irritation, redness.
Eye contact
Adverse symptoms may include the following: pain or irritation, watering, redness.
Specific target organ toxicity (single exposure)
Specific target organ toxicity (repeated exposure)
Aspiration hazard
Potential acute health effects
Classification
Styrene – 2B Reasonably anticipated to be a human carcinogen.
Carbon Black – 2B –
Cobalt 2-Ethylhexanoate – 2B –
Product/ingredient name NTPIARCACGIH
May cause sensitization by skin contact.
No mutagenic effect.
1) Negative Study A published study concluded that the mechanism for producing cancer in mice exposed to styrene
is not applicable in human metabolism. (June 2013 Pharmacology & Toxicology 66 (2013))
2) Negative Study A recent update to an extensive study of reinforced plastic workers from 1948-1977 concluded that
there was no coherent evidence that styrene exposure increased risk of cancer (March 2013 Epidemiology Vol. 24
Issue 2)
3) Positive Study Styrene induced pulmonary toxicity and carcinogenicity in mice was shown to be caused by a
metabolite of styrene, probably styrene oxide. (Dec.2001 Toxicology Vol.169 Issue 2)
Not considered to be toxic to the reproductive system.
No known effect according to our database..
No known effect according to our database.
A study of long term effects of workers exposed to styrene levels in the range of 25-35 ppm, 8 hour TWA, indicated a
possible mild hearing loss.
No known effect according to our database.
Inhalation
Page: 7 of 10G130LN71196
Section 12. Ecological information
LogPow BCF Potential
Bioaccumulative potential
Other adverse effects
No known effect according to our database.
Product/ingredient name
Styrene 2.95 13.49 low
Product/ingredient name Aquatic half-life Photolysis Biodegradability
Styrene – – Readily
Toxicity
Styrene Acute EC50 4.7 mg/l Fresh water Daphnia – Daphnia magna 48 hours
Acute LC50 4.02 mg/l Fresh water Fish – Pimephales promelas 96 hours
Product/ingredient name SpeciesResult Exposure
Persistence and degradability
Styrene EU 100 % – Readily – 1 days – –
Product/ingredient name Test DoseResult Inoculum
Soil/water partition coefficient (KOC)
Not available.
Mobility in soil
Section 13. Disposal considerations
The generation of waste should be avoided or minimized wherever possible. Empty containers or liners may retain some
product residues. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Disposal of
this product, solutions and any by-products should at all times comply with the requirements of environmental protection
and waste disposal legislation and any regional local authority requirements. Avoid disposal. Attempt to use product
completely in accordance with intended use. Waste packaging should be recycled. Incineration or landfill should only be
considered when recycling is not feasible.
Disposal methods
The information in this section contains generic advice and guidance. The list of Identified Uses in Section 1 should be consulted for any available use-specific information
provided in the Exposure Scenario(s).
Special precautions
This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers
that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Do not cut, weld
or grind used containers unless they have been cleaned thoroughly internally. Avoid dispersal of spilled material and runoff
and contact with soil, waterways, drains and sewers.
Section 14. Transport information
Resin Solution
3
III
UN1866UN number
Proper shipping name
Transport hazard class(es)
Packing group
DOT / TDG/ IMDG/IMO / ICAO/IATA and National regulations.
Additional information US regulations require the reporting of spills when the amount exceeds the Reportable
Quantity (RQ) for specific components of this material. See CERCLA in Section 15,
Regulatory Information, for the Reportable Quantities.
Environmental hazards Marine pollutant: No.
IMDGEmergency schedules (EmS): F-E, S-E
Remarks: FP-31 C
IATANo additional information.
Page: 8 of 10G130LN71196
Section 14. Transport information
Special precautions for user Transport within user s premises: always transport in closed containers that are upright
and secure. Ensure that persons transporting the product know what to do in the event of
an accident or spillage.
Section 15. Regulatory information
Inventories (National and International)
:All components are listed or exempted.
SARA 313
Product name
Styrene 100-42-5
Cobalt 2-Ethylhexanoate 136-52-7
Form R – Reporting
requirements
SARA 311/312
Styrene Yes. No. No. No. Yes.
Carbon Black No. No. No. No. Yes.
Petroleum Naphtha Yes. No. No. Yes. Yes.
Cobalt 2-Ethylhexanoate No. No. No. Yes. Yes.
Name Fire
hazard
Sudden
release of
pressure
Reactive Immediate
(acute)
health hazard
Delayed
(chronic)
health hazard
Composition/information on ingredients
United States inventory (TSCA 8b)
Australia (AICS) :Not determined.
Canada (DSL) :All components are listed or exempted.
China (IECSC) :All components are listed or exempted.
Europe (EINECS) :Not determined.
Japan (ENCS) :Japan inventory (ENCS): Not determined.
Japan inventory (ISHL): Not determined.
Republic of Korea (KECI) :Not determined.
Malaysia (EHS Register) :Not determined.
New Zealand (NZIoC) :Not determined.
Philippines (PICCS) :Not determined.
Taiwan (CSNN) :Not determined.
CAS number
WARNING: This product contains a chemical known to the State of California to cause cancer.
WARNING: This product contains less than 1% of a chemical known to the State of California to cause birth defects or other reproductive
harm.
California Prop. 65
State regulations
Styrene – 1000 lbs. (453.6 kg)CERCLA RQ –
Section 16. Other information
History
Date of issue
Date of previous issue
:
:
02/01/2017
05/26/2015
1
3
2
National Fire Protection Association (U.S.A.)
Health
Special
Instability/Reactivity
Flammability
Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency Response Copyright 1997, National Fire Protection Association, Quincy, MA 02269. This
reprinted material is not the complete and official position of the National Fire Protection Association, on the referenced subject which is represented only by the standard in its entirety.
Copyright 2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to be interpreted and applied only by properly trained individuals to identify fire, health and
reactivity hazards of chemicals. The user is referred to certain limited number of chemicals with recommended classifications in NFPA 49 and NFPA 325, which would be used as a guideline only.
Whether the chemicals are classified by NFPA or not, anyone using the 704 systems to classify chemicals does so at their own risk.
Page: 9 of 10G130LN71196
Section 16. Other information
Version
The information contained in this data sheet is furnished in good faith and without warranty, representation, or inducement or license of any kind,
except that it is accurate to the best of AOC, LLC’s knowledge, or was obtained from sources believed by AOC, LLC to be reliable. The
accuracy, adequacy or completeness of health and safety precautions set forth herein cannot be guaranteed, and the buyer is solely
responsible for ensuring that the product is used, handled, stored, and disposed of safely and in compliance with applicable federal, state or
provincial, and local laws. AOC, LLC disclaims liability for any loss, damage or personal injury that arises from, or is in any way related to, use
of the information contained in this data sheet.
Notice to reader
:
Indicates information that has changed from previously issued version.
Key to abbreviations :ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by
the Protocol of 1978. (“Marpol” = marine pollution)
UN = United Nations
2.0
AOC Corporate Regulatory Affairs
This Safety Data Sheet (SDS) and its content are the confidential and proprietary information of AOC and it may not be modified, altered,
deconstructed, or presented in any other manner, without the explicit authorization of AOC and/or its legal counsel.
Page: 10 of 10G130LN71196
by | Sep 27, 2025
Gel Coat
Product name
Product type
Emergency telephone number
Section 1. Identification
Chemical family Aromatic.
Supplier’s details AOC, LLC
955 Highway 57 East
Collierville, TN 38017
E-Mail: aoc.sds@aoc-resins.com
Website: www.aoc-resins.com
Phone Number: (901) 854-2800
Hours: 8AM-5pm (Central Time) Monday-Friday
Relevant identified uses of the substance or mixture and uses advised against
SDS No. NA-1504:1802 (Version: 2.0)
Uses advised against
Identified uses Used in the manufacture of thermoset plastic parts.
No additional information.
G440LW
CHEMTREC Within USA and Canada
CHEMTREC Outside USA and Canada
CANUTEC Within Canada
+1 (800) 424-9300
+1 (703) 527-3887
+1 (613) 996-6666
CCN1023
SAFETY DATA SHEET
Date of issue: 02/01/2017
Date of previous issue: 05/26/2015
Section 2. Hazards identification
OSHA/HCS status
FLAMMABLE LIQUIDS Category 3 H226
SKIN CORROSION/IRRITATION Category 2 H315
SERIOUS EYE DAMAGE/ EYE IRRITATION Category 2 H319
ACUTE TOXICITY (INHALATION) Category 4 H332
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) Category 3 H335
REPRODUCTIVE TOXICITY Category 2 H361d
CARCINOGENICITY Category 2 H351
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) Category 1 H372
ASPIRATION HAZARD Category 1 H304
Classification of the substance or mixture
Signal word
Danger
Hazard statements
H226: Flammable liquid and vapor.
H332: Harmful if inhaled.
H361d: Suspected of damaging the unborn child.
H351: Suspected of causing cancer.
H319: Causes serious eye irritation.
H315: Causes skin irritation.
H335: May cause respiratory irritation.
H372: Causes damage to organs through prolonged or repeated exposure if inhaled.
H304: May be fatal if swallowed and enters airways.
Hazard pictograms
GHS label elements
This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Page: 1 of 10G440LW
Section 2. Hazards identification
Precautionary statements
Prevention
P210: Keep away from heat, sparks, open flames and hot surfaces. – No smoking.
P233: Keep container tightly closed.
P240: Ground/bond container and receiving equipment.
P241: Use explosion-proof electrical/ventilating/lighting/material-handling equipment.
P242: Use only non-sparking tools.
P243: Take precautionary measures against static discharge.
P201: Obtain special instructions before use.
P202: Do not handle until all safety precautions have been read and understood.
P264: Wash hands thoroughly after handling.
P270: Do not eat, drink or smoke when using this product.
P271: Use only outdoors or in a well-ventilated area.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P260: Do not breathe vapor or mist.
Response
P370+P378: In case of fire: Use dry chemical, CO , water spray (fog) or foam.
P301+P310: IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.
P331: Do NOT induce vomiting.
P308+P313: IF exposed or concerned: Get medical advice/attention.
P304+P340: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P312: Call a POISON CENTER or physician if you feel unwell.
P303+P361+P353: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower.
P332+P313: If skin irritation occurs, get medical advice/attention.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing.
P337+P313: If eye irritation persists, get medical advice/attention.
P308+P311: IF exposed or concerned: Call a POISON CENTER or doctor/physician.
P391: Collect spillage.
Storage
P403 + P235: Store in a well-ventilated place. Keep cool.
P233: Keep container tightly closed.
P405: Store locked up.
Disposal
P501: Dispose of contents and container in accordance with all local, regional, national and international regulations.
General
P101: If medical advice is needed, have product container or label at hand.
P102: Keep out of reach of children.
Hazards not otherwise classified
None known.
Section 3. Composition/information on ingredients
Ingredient name CAS number %
There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are
classified as hazardous to health or the environment and hence require reporting in this section.
Substance/mixture :
Occupational exposure limits, if available, are listed in Section 8.
Mixture.
Styrene 100-42-5 39.5
Vinyl Toluene 25013-15-4 4
Petroleum Naphtha 64742-95-6 0.3
Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Use of
buffered baby shampoo will aid in removal. If irritation persists, get medical attention.
Move the victim to a safe area as soon as possible. Allow the victim to rest in a well-ventilated area. If breathing is difficult, give
oxygen. If the victim is not breathing, perform mouth-to-mouth resuscitation. Seek immediate medical attention.
Section 4. First aid measures
Eye contact
Inhalation
Description of necessary first aid measures
Page: 2 of 10G440LW
Section 4. First aid measures
Wash out mouth with water. Remove dentures if any. Stop if the exposed person feels sick as vomiting may be dangerous. Do
not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit
does not enter the lungs. Seek immediate medical attention.
In case of contact, immediately flush skin with plenty of water. Remove contaminated clothing and shoes. If irritation persists,
seek medical attention. Wash contaminated clothing before reuse. Clean shoes thoroughly before reuse.
Skin contact
Ingestion
Notes to physician
Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.
Most important symptoms/effects, acute and delayed
See toxicological information (Section 11)
Indication of immediate medical attention and special treatment needed, if necessary
Irritating to mouth, throat and stomach.
Causes serious eye irritation.
Causes skin irritation.
Harmful if inhaled. May cause respiratory irritation.
Eye contact
Skin contact
Inhalation
Ingestion
Over-exposure signs/symptoms
Eye contact
Inhalation
Skin contact
Ingestion
Adverse symptoms may include the following: pain or irritation, watering, redness.
Adverse symptoms may include the following: respiratory tract irritation, coughing.
Adverse symptoms may include the following: irritation, redness.
Adverse symptoms may include the following: Irritating to mouth, throat and stomach..
Section 5. Fire-fighting measures
Fire water contaminated with this material must be contained and prevented from being discharged to any waterway, sewer or
drain.
Hazardous thermal decomposition products
Specific hazards arising from the chemical
Decomposition products may include the following materials: carbon dioxide, carbon monoxide, sulfur oxides halogenated
compounds, metal oxide/oxides
Flammable liquid and vapor. In a fire or if heated, a pressure increase will occur and the container may burst, with the risk of a
subsequent explosion. The vapor/gas is heavier than air and will spread along the ground. Vapors may accumulate in low or
confined areas or travel a considerable distance to a source of ignition and flash back. Runoff to sewer may create fire or
explosion hazard. This material is harmful to aquatic life with long lasting effects. Fire water contaminated with this material must
be contained and prevented from being discharged to any waterway, sewer or drain.
Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece
operated in positive pressure mode.
Special protective equipment for fire-fighters
Use dry chemical, CO , water spray (fog) or foam.
Extinguishing media
Do not use water jet.
Suitable extinguishing media
Unsuitable extinguishing media
Special protective actions for fire-fighters
Page: 3 of 10G440LW
Section 6. Accidental release measures
Environmental precautions
Personal precautions, protective equipment and emergency procedures
Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water
courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and
collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in
container for disposal according to local regulations (see Section 13). Use spark-proof tools and explosion-proof equipment.
Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled
product. Note: see Section 1 for emergency contact information and Section 13 for waste disposal.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities
if the product has caused environmental pollution (sewers, waterways, soil or air). Water polluting material. May be harmful to
the environment if released in large quantities.
Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-
insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Use spark-proof tools and
explosion-proof equipment. Dispose of via a licensed waste disposal contractor.
Methods and materials for containment and cleaning up
For non-emergency personnel
For emergency responders
No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Do not touch or
walk through spilled material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Avoid breathing vapor or
mist. Provide adequate ventilation.
If specialised clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable
materials. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. See
also the information in “For non-emergency personnel”.
Small spill
Large spill
Section 7. Handling and storage
Advice on general occupational hygiene
Conditions for safe storage, including any incompatibilities
Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers
should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment
before entering eating areas. See also Section 8 for additional information on hygiene measures.
Store in accordance with local regulations. Store in a segregated and approved area. Store in original container protected from
direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink.
Eliminate all ignition sources. Segregate from oxidizing materials. Keep container tightly closed and sealed until ready for use.
Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled
containers. Use appropriate containment to avoid environmental contamination. Refer to the product label and/or technical data
sheet for further information.
Protective measures
Put on appropriate personal protective equipment (see Section 8). Eating, drinking and smoking should be prohibited in areas
where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking.
Remove contaminated clothing and protective equipment before entering eating areas. Do not breathe vapor or mist. Do not
ingest. Avoid contact with eyes, skin and clothing. Avoid release to the environment. Use only with adequate ventilation. Wear
appropriate respirator when ventilation is inadequate. Do not enter storage areas and confined spaces unless adequately
ventilated. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when
not in use. Store and use away from heat, sparks, open flame or any other ignition source. Use explosion-proof electrical
(ventilating, lighting and material handling) equipment. Use only non-sparking tools. Take precautionary measures against
electrostatic discharges. Empty containers retain product residue and can be hazardous. Do not reuse container.
Precautions for safe handling
Section 8. Exposure controls/personal protection
Control parameters
Occupational exposure limits
Page: 4 of 10G440LW
Section 8. Exposure controls/personal protection
Styrene ACGIH TLV (United States, 3/2015).
TWA: 20 ppm 8 hours.
TWA: 85 mg/m 8 hours.
STEL: 40 ppm 15 minutes.
STEL: 170 mg/m 15 minutes.
OSHA PEL Z2 (United States, 2/2013).
TWA: 100 ppm 8 hours.
CEIL: 200 ppm
AMP: 600 ppm 5 minutes.
NIOSH REL (United States, 10/2013).
TWA: 50 ppm 10 hours.
TWA: 215 mg/m 10 hours.
STEL: 100 ppm 15 minutes.
STEL: 425 mg/m 15 minutes.
Vinyl Toluene ACGIH TLV (United States, 3/2015).
TWA: 50 ppm 8 hours.
TWA: 242 mg/m 8 hours.
STEL: 100 ppm 15 minutes.
STEL: 483 mg/m 15 minutes.
NIOSH REL (United States, 10/2013).
TWA: 100 ppm 10 hours.
TWA: 480 mg/m 10 hours.
OSHA PEL (United States, 2/2013).
TWA: 100 ppm 8 hours.
TWA: 480 mg/m 8 hours.
Ingredient name Exposure limits
Hand protection
Use a properly fitted, air-purifying or air-fed respirator complying with an approved standard if a risk assessment indicates this is
necessary. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe
working limits of the selected respirator.
Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical
products if a risk assessment indicates this is necessary.
Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid
exposure to liquid splashes, mists or dusts.
Eye/face protection
Respiratory protection
Body protection
Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should
be approved by a specialist before handling this product.
Appropriate engineering controls
Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or other engineering controls to keep
worker exposure to airborne contaminants below any recommended or statutory limits. The engineering controls also need
to keep gas, vapor or dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment.
Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at
the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Ensure that
eyewash stations and safety showers are close to the workstation location.
Hygiene measures
Individual protection measures
Other skin protection
Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the
risks involved and should be approved by a specialist before handling this product.
Section 9. Physical and chemical properties
Physical state
Melting point
Liquid.
-23.8 F / -30.6 C (Styrene)
Aromatic.Odor
pH
Clear.Color
Not applicable.
0.01 – 0.1 ppm (Styrene)Odor threshold
Appearance
Page: 5 of 10G440LW
Section 9. Physical and chemical properties
Vapor pressure
Relative density
Vapor density
Solubility
1.1 to 1.4 (Water = 1)
3.6 (Air = 1) (Styrene )
5.0 mm Hg@ 68 F / 20 C (Styrene)
Slight.
Evaporation rate < 1 (Butyl acetate = 1)
Auto-ignition temperature
Flash point
914 F / 490 C (Styrene)
88 F / 31 C (Styrene)
Not available.
Viscosity Not available.
Partition coefficient: n-octanol/water
Boiling point 293 F / 145 C (Styrene)
Flammability (solid, gas) Not applicable.
Lower and upper explosive (flammable) limits Lower: 1.1% Upper: 6.1% (Styrene)
Molecular weight Not available.
Decomposition temperature Not available.
Section 10. Stability and reactivity
Hazardous decomposition products
Conditions to avoid
Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld, braze, solder, drill, grind or expose
containers to heat or sources of ignition.
Under normal conditions of storage and use, hazardous decomposition products should not be produced.
The product is stable. Stable under recommended storage and handling conditions (see Section 7).
Chemical stability
Reactive or incompatible with the following materials: oxidizing materials
Incompatible materials
Possibility of hazardous reactions
Under normal conditions of storage and use, hazardous reactions will not occur.
Reactivity
No specific test data related to reactivity available for this product or its ingredients.
Section 11. Toxicological information
Acute toxicity
Styrene LC50 Inhalation Gas. Rat 2770 ppm 4 hours
LC50 Inhalation Vapor Rat 11800 mg/m 4 hours
LD50 Oral Rat 2650 mg/kg -
Vinyl Toluene LD50 Oral Rat 2255 mg/kg -
Petroleum Naphtha LD50 Oral Rat 8400 mg/kg -
Product/ingredient name Result Species Dose Exposure
Carcinogenicity
Irritation/Corrosion
Styrene Eyes - Mild irritant Human - 50 parts per
million
-
Eyes - Moderate irritant Rabbit - 24 hours 100
milligrams
-
Eyes - Severe irritant Rabbit - 100 milligrams-
Skin - Mild irritant Rabbit - 500 milligrams-
Skin - Moderate irritant Rabbit - 100 Percent -
Vinyl Toluene Eyes - Mild irritant Rabbit - 90 milligrams -
Skin - Moderate irritant Rabbit - 100 Percent -
Product/ingredient name Result Score Exposure Observation
Sensitization
Species
Information on toxicological effects
Classification
Styrene - 2B Reasonably anticipated to be a human carcinogen.
Vinyl Toluene - 3 -
Product/ingredient name NTPIARCACGIH
May cause sensitization by skin contact.
Page: 6 of 10G440LW
Section 11. Toxicological information
Mutagenicity
Teratogenicity
Reproductive toxicity
Inhalation
Harmful if inhaled. May cause respiratory irritation.
Irritating to mouth, throat and stomach.
Ingestion
Skin contact
Causes skin irritation.
Causes serious eye irritation.
Eye contact
Symptoms related to the physical, chemical and toxicological characteristics
Skin contact
Ingestion
Adverse symptoms may include the following: respiratory tract irritation, coughing.
Adverse symptoms may include the following: Irritating to mouth, throat and stomach..
Adverse symptoms may include the following: irritation, redness.
Eye contact
Adverse symptoms may include the following: pain or irritation, watering, redness.
Specific target organ toxicity (single exposure)
Specific target organ toxicity (repeated exposure)
Aspiration hazard
Potential acute health effects
No mutagenic effect.
1) Negative Study A published study concluded that the mechanism for producing cancer in mice exposed to styrene
is not applicable in human metabolism. (June 2013 Pharmacology & Toxicology 66 (2013))
2) Negative Study A recent update to an extensive study of reinforced plastic workers from 1948-1977 concluded that
there was no coherent evidence that styrene exposure increased risk of cancer (March 2013 Epidemiology Vol. 24
Issue 2)
3) Positive Study Styrene induced pulmonary toxicity and carcinogenicity in mice was shown to be caused by a
metabolite of styrene, probably styrene oxide. (Dec.2001 Toxicology Vol.169 Issue 2)
Not considered to be toxic to the reproductive system.
No known effect according to our database..
No known effect according to our database.
A study of long term effects of workers exposed to styrene levels in the range of 25-35 ppm, 8 hour TWA, indicated a
possible mild hearing loss.
No known effect according to our database.
Inhalation
Section 12. Ecological information
Bioaccumulative potential
Product/ingredient name Aquatic half-life Photolysis Biodegradability
Styrene - - Readily
Toxicity
Styrene Acute EC50 4.7 mg/l Fresh water Daphnia - Daphnia magna 48 hours
Acute LC50 4.02 mg/l Fresh water Fish - Pimephales promelas 96 hours
Vinyl Toluene Acute EC50 1 to 10 mg/l Fresh water Daphnia - Daphnia magna 48 hours
Acute LC50 8.9 mg/l Marine water Crustaceans - Chaetogammarus
marinus - Young
48 hours
Product/ingredient name SpeciesResult Exposure
Persistence and degradability
Styrene EU 100 % - Readily - 1 days - -
Product/ingredient name Test DoseResult Inoculum
Page: 7 of 10G440LW
Section 12. Ecological information
LogPow BCF Potential
Other adverse effects
No known effect according to our database.
Product/ingredient name
Styrene 2.95 13.49 low
Vinyl Toluene - 100 to 320 low
Soil/water partition coefficient (KOC)
Not available.
Mobility in soil
Section 13. Disposal considerations
The generation of waste should be avoided or minimized wherever possible. Empty containers or liners may retain some
product residues. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Disposal of
this product, solutions and any by-products should at all times comply with the requirements of environmental protection
and waste disposal legislation and any regional local authority requirements. Avoid disposal. Attempt to use product
completely in accordance with intended use. Waste packaging should be recycled. Incineration or landfill should only be
considered when recycling is not feasible.
Disposal methods
The information in this section contains generic advice and guidance. The list of Identified Uses in Section 1 should be consulted for any available use-specific information
provided in the Exposure Scenario(s).
Special precautions
This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers
that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Do not cut, weld
or grind used containers unless they have been cleaned thoroughly internally. Avoid dispersal of spilled material and runoff
and contact with soil, waterways, drains and sewers.
Section 14. Transport information
Resin Solution
3
III
UN1866UN number
Proper shipping name
Transport hazard class(es)
Packing group
DOT / TDG/ IMDG/IMO / ICAO/IATA and National regulations.
Additional information US regulations require the reporting of spills when the amount exceeds the Reportable
Quantity (RQ) for specific components of this material. See CERCLA in Section 15,
Regulatory Information, for the Reportable Quantities.
Environmental hazards Marine pollutant: No.
Special precautions for user Transport within user s premises: always transport in closed containers that are upright
and secure. Ensure that persons transporting the product know what to do in the event of
an accident or spillage.
IMDGEmergency schedules (EmS): F-E, S-E
Remarks: FP-31 C
IATANo additional information.
Section 15. Regulatory information
Inventories (National and International)
:All components are listed or exempted.United States inventory (TSCA 8b)
Australia (AICS) :Not determined.
Canada (DSL) :All components are listed or exempted.
China (IECSC) :Not determined.
Europe (EINECS) :Not determined.
New Zealand (NZIoC) :Not determined.
Page: 8 of 10G440LW
Section 15. Regulatory information
SARA 313
Product name
Styrene 100-42-5
Form R - Reporting
requirements
SARA 311/312
Styrene Yes. No. No. No. Yes.
Vinyl Toluene Yes. No. No. Yes. Yes.
Petroleum Naphtha Yes. No. No. Yes. Yes.
Name Fire
hazard
Sudden
release of
pressure
Reactive Immediate
(acute)
health hazard
Delayed
(chronic)
health hazard
Composition/information on ingredients
Japan (ENCS) :Japan inventory (ENCS): Not determined.
Japan inventory (ISHL): Not determined.
Republic of Korea (KECI) :Not determined.
Malaysia (EHS Register) :Not determined.
Philippines (PICCS) :Not determined.
Taiwan (CSNN) :Not determined.
CAS number
WARNING: This product contains a chemical known to the State of California to cause cancer.
WARNING: This product contains less than 1% of a chemical known to the State of California to cause birth defects or other reproductive
harm.
California Prop. 65
State regulations
Styrene - 1000 lbs. (453.6 kg)CERCLA RQ -
Section 16. Other information
History
Date of issue
Version
Notice to reader
Date of previous issue
:
:
:
Indicates information that has changed from previously issued version.
Key to abbreviations :ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by
the Protocol of 1978. ("Marpol" = marine pollution)
UN = United Nations
02/01/2017
05/26/2015
2.0
2
3
2
National Fire Protection Association (U.S.A.)
Health
Special
Instability/Reactivity
Flammability
Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency Response Copyright 1997, National Fire Protection Association, Quincy, MA 02269. This
reprinted material is not the complete and official position of the National Fire Protection Association, on the referenced subject which is represented only by the standard in its entirety.
Copyright 2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to be interpreted and applied only by properly trained individuals to identify fire, health and
reactivity hazards of chemicals. The user is referred to certain limited number of chemicals with recommended classifications in NFPA 49 and NFPA 325, which would be used as a guideline only.
Whether the chemicals are classified by NFPA or not, anyone using the 704 systems to classify chemicals does so at their own risk.
AOC Corporate Regulatory Affairs
Page: 9 of 10G440LW
Section 16. Other information
The information contained in this data sheet is furnished in good faith and without warranty, representation, or inducement or license of any kind,
except that it is accurate to the best of AOC, LLC's knowledge, or was obtained from sources believed by AOC, LLC to be reliable. The
accuracy, adequacy or completeness of health and safety precautions set forth herein cannot be guaranteed, and the buyer is solely
responsible for ensuring that the product is used, handled, stored, and disposed of safely and in compliance with applicable federal, state or
provincial, and local laws. AOC, LLC disclaims liability for any loss, damage or personal injury that arises from, or is in any way related to, use
of the information contained in this data sheet.
This Safety Data Sheet (SDS) and its content are the confidential and proprietary information of AOC and it may not be modified, altered,
deconstructed, or presented in any other manner, without the explicit authorization of AOC and/or its legal counsel.
Page: 10 of 10G440LW
by | Sep 27, 2025
Gel Coat
Product name
Product type
Emergency telephone number
Section 1. Identification
Chemical family Aromatic.
Supplier’s details AOC, LLC
955 Highway 57 East
Collierville, TN 38017
E-Mail: aoc.sds@aoc-resins.com
Website: www.aoc-resins.com
Phone Number: (901) 854-2800
Hours: 8AM-5pm (Central Time) Monday-Friday
Relevant identified uses of the substance or mixture and uses advised against
SDS No. NA-1504:1801 (Version: 2.0)
Uses advised against
Identified uses Used in the manufacture of thermoset plastic parts.
No additional information.
G440LU
CHEMTREC Within USA and Canada
CHEMTREC Outside USA and Canada
CANUTEC Within Canada
+1 (800) 424-9300
+1 (703) 527-3887
+1 (613) 996-6666
CCN1023
SAFETY DATA SHEET
Date of issue: 02/01/2017
Date of previous issue: 05/26/2015
Section 2. Hazards identification
OSHA/HCS status
FLAMMABLE LIQUIDS Category 3 H226
SKIN CORROSION/IRRITATION Category 2 H315
SERIOUS EYE DAMAGE/ EYE IRRITATION Category 2 H319
ACUTE TOXICITY (INHALATION) Category 4 H332
SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) Category 3 H335
REPRODUCTIVE TOXICITY Category 2 H361d
CARCINOGENICITY Category 2 H351
SPECIFIC TARGET ORGAN TOXICITY (REPEATED EXPOSURE) Category 1 H372
ASPIRATION HAZARD Category 1 H304
Classification of the substance or mixture
Signal word
Danger
Hazard statements
H226: Flammable liquid and vapor.
H332: Harmful if inhaled.
H361d: Suspected of damaging the unborn child.
H351: Suspected of causing cancer.
H319: Causes serious eye irritation.
H315: Causes skin irritation.
H335: May cause respiratory irritation.
H372: Causes damage to organs through prolonged or repeated exposure if inhaled.
H304: May be fatal if swallowed and enters airways.
Hazard pictograms
GHS label elements
This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Page: 1 of 10G440LU
Section 2. Hazards identification
Precautionary statements
Prevention
P210: Keep away from heat, sparks, open flames and hot surfaces. – No smoking.
P233: Keep container tightly closed.
P240: Ground/bond container and receiving equipment.
P241: Use explosion-proof electrical/ventilating/lighting/material-handling equipment.
P242: Use only non-sparking tools.
P243: Take precautionary measures against static discharge.
P201: Obtain special instructions before use.
P202: Do not handle until all safety precautions have been read and understood.
P264: Wash hands thoroughly after handling.
P270: Do not eat, drink or smoke when using this product.
P271: Use only outdoors or in a well-ventilated area.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P260: Do not breathe vapor or mist.
Response
P370+P378: In case of fire: Use dry chemical, CO , water spray (fog) or foam.
P301+P310: IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.
P331: Do NOT induce vomiting.
P308+P313: IF exposed or concerned: Get medical advice/attention.
P304+P340: IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P312: Call a POISON CENTER or physician if you feel unwell.
P303+P361+P353: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower.
P332+P313: If skin irritation occurs, get medical advice/attention.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing.
P337+P313: If eye irritation persists, get medical advice/attention.
P308+P311: IF exposed or concerned: Call a POISON CENTER or doctor/physician.
P391: Collect spillage.
Storage
P403 + P235: Store in a well-ventilated place. Keep cool.
P233: Keep container tightly closed.
P405: Store locked up.
Disposal
P501: Dispose of contents and container in accordance with all local, regional, national and international regulations.
General
P101: If medical advice is needed, have product container or label at hand.
P102: Keep out of reach of children.
Hazards not otherwise classified
None known.
Section 3. Composition/information on ingredients
Ingredient name CAS number %
There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are
classified as hazardous to health or the environment and hence require reporting in this section.
Substance/mixture :
Occupational exposure limits, if available, are listed in Section 8.
Mixture.
Styrene 100-42-5 37.6
Methyl Methacrylate 80-62-6 5.0
Petroleum Naphtha 64742-95-6 0.3
Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelids. Use of
buffered baby shampoo will aid in removal. If irritation persists, get medical attention.
Move the victim to a safe area as soon as possible. Allow the victim to rest in a well-ventilated area. If breathing is difficult, give
oxygen. If the victim is not breathing, perform mouth-to-mouth resuscitation. Seek immediate medical attention.
Section 4. First aid measures
Eye contact
Inhalation
Description of necessary first aid measures
Page: 2 of 10G440LU
Section 4. First aid measures
Wash out mouth with water. Remove dentures if any. Stop if the exposed person feels sick as vomiting may be dangerous. Do
not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit
does not enter the lungs. Seek immediate medical attention.
In case of contact, immediately flush skin with plenty of water. Remove contaminated clothing and shoes. If irritation persists,
seek medical attention. Wash contaminated clothing before reuse. Clean shoes thoroughly before reuse.
Skin contact
Ingestion
Notes to physician
Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled.
Most important symptoms/effects, acute and delayed
See toxicological information (Section 11)
Indication of immediate medical attention and special treatment needed, if necessary
Irritating to mouth, throat and stomach.
Causes serious eye irritation.
Causes skin irritation.
Harmful if inhaled. May cause respiratory irritation.
Eye contact
Skin contact
Inhalation
Ingestion
Over-exposure signs/symptoms
Eye contact
Inhalation
Skin contact
Ingestion
Adverse symptoms may include the following: pain or irritation, watering, redness.
Adverse symptoms may include the following: respiratory tract irritation, coughing.
Adverse symptoms may include the following: irritation, redness.
Adverse symptoms may include the following: Irritating to mouth, throat and stomach..
Section 5. Fire-fighting measures
Fire water contaminated with this material must be contained and prevented from being discharged to any waterway, sewer or
drain.
Hazardous thermal decomposition products
Specific hazards arising from the chemical
Decomposition products may include the following materials: carbon dioxide, carbon monoxide, sulfur oxides halogenated
compounds, metal oxide/oxides
Flammable liquid and vapor. In a fire or if heated, a pressure increase will occur and the container may burst, with the risk of a
subsequent explosion. The vapor/gas is heavier than air and will spread along the ground. Vapors may accumulate in low or
confined areas or travel a considerable distance to a source of ignition and flash back. Runoff to sewer may create fire or
explosion hazard. This material is harmful to aquatic life with long lasting effects. Fire water contaminated with this material must
be contained and prevented from being discharged to any waterway, sewer or drain.
Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece
operated in positive pressure mode.
Special protective equipment for fire-fighters
Use dry chemical, CO , water spray (fog) or foam.
Extinguishing media
Do not use water jet.
Suitable extinguishing media
Unsuitable extinguishing media
Special protective actions for fire-fighters
Page: 3 of 10G440LU
Section 6. Accidental release measures
Environmental precautions
Personal precautions, protective equipment and emergency procedures
Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water
courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and
collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in
container for disposal according to local regulations (see Section 13). Use spark-proof tools and explosion-proof equipment.
Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled
product. Note: see Section 1 for emergency contact information and Section 13 for waste disposal.
Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities
if the product has caused environmental pollution (sewers, waterways, soil or air). Water polluting material. May be harmful to
the environment if released in large quantities.
Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-
insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Use spark-proof tools and
explosion-proof equipment. Dispose of via a licensed waste disposal contractor.
Methods and materials for containment and cleaning up
For non-emergency personnel
For emergency responders
No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Do not touch or
walk through spilled material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Avoid breathing vapor or
mist. Provide adequate ventilation.
If specialised clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable
materials. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. See
also the information in “For non-emergency personnel”.
Small spill
Large spill
Section 7. Handling and storage
Advice on general occupational hygiene
Conditions for safe storage, including any incompatibilities
Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers
should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment
before entering eating areas. See also Section 8 for additional information on hygiene measures.
Store in accordance with local regulations. Store in a segregated and approved area. Store in original container protected from
direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink.
Eliminate all ignition sources. Segregate from oxidizing materials. Keep container tightly closed and sealed until ready for use.
Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled
containers. Use appropriate containment to avoid environmental contamination. Refer to the product label and/or technical data
sheet for further information.
Protective measures
Put on appropriate personal protective equipment (see Section 8). Eating, drinking and smoking should be prohibited in areas
where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking.
Remove contaminated clothing and protective equipment before entering eating areas. Do not breathe vapor or mist. Do not
ingest. Avoid contact with eyes, skin and clothing. Avoid release to the environment. Use only with adequate ventilation. Wear
appropriate respirator when ventilation is inadequate. Do not enter storage areas and confined spaces unless adequately
ventilated. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when
not in use. Store and use away from heat, sparks, open flame or any other ignition source. Use explosion-proof electrical
(ventilating, lighting and material handling) equipment. Use only non-sparking tools. Take precautionary measures against
electrostatic discharges. Empty containers retain product residue and can be hazardous. Do not reuse container.
Precautions for safe handling
Section 8. Exposure controls/personal protection
Control parameters
Occupational exposure limits
Page: 4 of 10G440LU
Section 8. Exposure controls/personal protection
Styrene ACGIH TLV (United States, 3/2015).
TWA: 20 ppm 8 hours.
TWA: 85 mg/m 8 hours.
STEL: 40 ppm 15 minutes.
STEL: 170 mg/m 15 minutes.
OSHA PEL Z2 (United States, 2/2013).
TWA: 100 ppm 8 hours.
CEIL: 200 ppm
AMP: 600 ppm 5 minutes.
NIOSH REL (United States, 10/2013).
TWA: 50 ppm 10 hours.
TWA: 215 mg/m 10 hours.
STEL: 100 ppm 15 minutes.
STEL: 425 mg/m 15 minutes.
Methyl Methacrylate ACGIH TLV (United States, 3/2015). Skin sensitizer.
TWA: 50 ppm 8 hours.
STEL: 100 ppm 15 minutes.
NIOSH REL (United States, 10/2013).
TWA: 100 ppm 10 hours.
TWA: 410 mg/m 10 hours.
OSHA PEL (United States, 2/2013).
TWA: 100 ppm 8 hours.
TWA: 410 mg/m 8 hours.
ACGIH TLV (United States, 3/2012). Skin sensitizer.
STEL: 410 mg/m 8 hours.
TWA: 205 mg/m 8 hours.
Ingredient name Exposure limits
Hand protection
Use a properly fitted, air-purifying or air-fed respirator complying with an approved standard if a risk assessment indicates this is
necessary. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe
working limits of the selected respirator.
Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical
products if a risk assessment indicates this is necessary.
Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid
exposure to liquid splashes, mists or dusts.
Eye/face protection
Respiratory protection
Body protection
Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should
be approved by a specialist before handling this product.
Appropriate engineering controls
Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or other engineering controls to keep
worker exposure to airborne contaminants below any recommended or statutory limits. The engineering controls also need
to keep gas, vapor or dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment.
Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at
the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Ensure that
eyewash stations and safety showers are close to the workstation location.
Hygiene measures
Individual protection measures
Other skin protection
Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the
risks involved and should be approved by a specialist before handling this product.
Section 9. Physical and chemical properties
Physical state
Melting point
Liquid.
-23.8 F / -30.6 C (Styrene)
Aromatic.Odor
pH
Clear.Color
Not applicable.
0.01 – 0.1 ppm (Styrene)Odor threshold
Appearance
Page: 5 of 10G440LU
Section 9. Physical and chemical properties
Vapor pressure
Relative density
Vapor density
Solubility
1.1 to 1.4 (Water = 1)
3.6 (Air = 1) (Styrene )
5.0 mm Hg@ 68 F / 20 C (Styrene)
Slight.
Evaporation rate < 1 (Butyl acetate = 1)
Auto-ignition temperature
Flash point
914 F / 490 C (Styrene)
88 F / 31 C (Styrene)
Not available.
Viscosity Not available.
Partition coefficient: n-octanol/water
Boiling point 293 F / 145 C (Styrene)
Flammability (solid, gas) Not applicable.
Lower and upper explosive (flammable) limits Lower: 1.1% Upper: 6.1% (Styrene)
Molecular weight 1,000 to 15,000
Decomposition temperature Not available.
Section 10. Stability and reactivity
Hazardous decomposition products
Conditions to avoid
Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld, braze, solder, drill, grind or expose
containers to heat or sources of ignition.
Under normal conditions of storage and use, hazardous decomposition products should not be produced.
The product is stable. Stable under recommended storage and handling conditions (see Section 7).
Chemical stability
Reactive or incompatible with the following materials: oxidizing materials
Incompatible materials
Possibility of hazardous reactions
Under normal conditions of storage and use, hazardous reactions will not occur.
Reactivity
No specific test data related to reactivity available for this product or its ingredients.
Section 11. Toxicological information
Acute toxicity
Styrene LC50 Inhalation Gas. Rat 2770 ppm 4 hours
LC50 Inhalation Vapor Rat 11800 mg/m 4 hours
LD50 Oral Rat 2650 mg/kg -
Methyl Methacrylate LC50 Inhalation Gas. Rat 7094 ppm 4 hours
LC50 Inhalation Vapor Rat 78000 mg/m 4 hours
LD50 Dermal Rabbit >5 g/kg –
LD50 Oral Rat 7872 mg/kg –
LD50 Oral Rat 7872 mg/kg –
Petroleum Naphtha LD50 Oral Rat 8400 mg/kg –
Product/ingredient name Result Species Dose Exposure
Carcinogenicity
Irritation/Corrosion
Styrene Eyes – Mild irritant Human – 50 parts per
million
–
Eyes – Moderate irritant Rabbit – 24 hours 100
milligrams
–
Eyes – Severe irritant Rabbit – 100 milligrams-
Skin – Mild irritant Rabbit – 500 milligrams-
Skin – Moderate irritant Rabbit – 100 Percent –
Product/ingredient name Result Score Exposure Observation
Sensitization
Species
Information on toxicological effects
Classification
May cause sensitization by skin contact.
Page: 6 of 10G440LU
Section 11. Toxicological information
Mutagenicity
Teratogenicity
Reproductive toxicity
Inhalation
Harmful if inhaled. May cause respiratory irritation.
Irritating to mouth, throat and stomach.
Ingestion
Skin contact
Causes skin irritation.
Causes serious eye irritation.
Eye contact
Symptoms related to the physical, chemical and toxicological characteristics
Skin contact
Ingestion
Adverse symptoms may include the following: respiratory tract irritation, coughing.
Adverse symptoms may include the following: Irritating to mouth, throat and stomach..
Adverse symptoms may include the following: irritation, redness.
Eye contact
Adverse symptoms may include the following: pain or irritation, watering, redness.
Specific target organ toxicity (single exposure)
Specific target organ toxicity (repeated exposure)
Aspiration hazard
Potential acute health effects
Styrene – 2B Reasonably anticipated to be a human carcinogen.
Methyl Methacrylate – 3 –
Product/ingredient name NTPIARCACGIH
No mutagenic effect.
1) Negative Study A published study concluded that the mechanism for producing cancer in mice exposed to styrene
is not applicable in human metabolism. (June 2013 Pharmacology & Toxicology 66 (2013))
2) Negative Study A recent update to an extensive study of reinforced plastic workers from 1948-1977 concluded that
there was no coherent evidence that styrene exposure increased risk of cancer (March 2013 Epidemiology Vol. 24
Issue 2)
3) Positive Study Styrene induced pulmonary toxicity and carcinogenicity in mice was shown to be caused by a
metabolite of styrene, probably styrene oxide. (Dec.2001 Toxicology Vol.169 Issue 2)
Not considered to be toxic to the reproductive system.
No known effect according to our database..
No known effect according to our database.
A study of long term effects of workers exposed to styrene levels in the range of 25-35 ppm, 8 hour TWA, indicated a
possible mild hearing loss.
No known effect according to our database.
Inhalation
Section 12. Ecological information
Toxicity
Styrene Acute EC50 4.7 mg/l Fresh water Daphnia – Daphnia magna 48 hours
Acute LC50 4.02 mg/l Fresh water Fish – Pimephales promelas 96 hours
Methyl Methacrylate Acute LC50 130000 g/l Fresh water Fish – Pimephales promelas – Adult96 hours
Product/ingredient name SpeciesResult Exposure
Persistence and degradability
Styrene EU 100 % – Readily – 1 days – –
Product/ingredient name Test DoseResult Inoculum
Page: 7 of 10G440LU
Section 12. Ecological information
LogPow BCF Potential
Bioaccumulative potential
Other adverse effects
No known effect according to our database.
Product/ingredient name
Styrene 2.95 13.49 low
Methyl Methacrylate 1.38 – low
Product/ingredient name Aquatic half-life Photolysis Biodegradability
Styrene – – Readily
Soil/water partition coefficient (KOC)
Not available.
Mobility in soil
Section 13. Disposal considerations
The generation of waste should be avoided or minimized wherever possible. Empty containers or liners may retain some
product residues. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Disposal of
this product, solutions and any by-products should at all times comply with the requirements of environmental protection
and waste disposal legislation and any regional local authority requirements. Avoid disposal. Attempt to use product
completely in accordance with intended use. Waste packaging should be recycled. Incineration or landfill should only be
considered when recycling is not feasible.
Disposal methods
The information in this section contains generic advice and guidance. The list of Identified Uses in Section 1 should be consulted for any available use-specific information
provided in the Exposure Scenario(s).
Special precautions
This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers
that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Do not cut, weld
or grind used containers unless they have been cleaned thoroughly internally. Avoid dispersal of spilled material and runoff
and contact with soil, waterways, drains and sewers.
Section 14. Transport information
Resin Solution
3
III
UN1866UN number
Proper shipping name
Transport hazard class(es)
Packing group
DOT / TDG/ IMDG/IMO / ICAO/IATA and National regulations.
Additional information US regulations require the reporting of spills when the amount exceeds the Reportable
Quantity (RQ) for specific components of this material. See CERCLA in Section 15,
Regulatory Information, for the Reportable Quantities.
Environmental hazards Marine pollutant: No.
Special precautions for user Transport within user s premises: always transport in closed containers that are upright
and secure. Ensure that persons transporting the product know what to do in the event of
an accident or spillage.
IMDGEmergency schedules (EmS): F-E, S-E
Remarks: FP-31 C
IATANo additional information.
Page: 8 of 10G440LU
Section 15. Regulatory information
Inventories (National and International)
:All components are listed or exempted.
SARA 313
Product name
Styrene 100-42-5
Methyl Methacrylate 80-62-6
Form R – Reporting
requirements
SARA 311/312
Styrene Yes. No. No. No. Yes.
Methyl Methacrylate Yes. No. No. Yes. No.
Petroleum Naphtha Yes. No. No. Yes. Yes.
Name Fire
hazard
Sudden
release of
pressure
Reactive Immediate
(acute)
health hazard
Delayed
(chronic)
health hazard
Composition/information on ingredients
United States inventory (TSCA 8b)
Australia (AICS) :Not determined.
Canada (DSL) :All components are listed or exempted.
China (IECSC) :Not determined.
Europe (EINECS) :Not determined.
Japan (ENCS) :Japan inventory (ENCS): Not determined.
Japan inventory (ISHL): Not determined.
Republic of Korea (KECI) :Not determined.
Malaysia (EHS Register) :Not determined.
New Zealand (NZIoC) :Not determined.
Philippines (PICCS) :Not determined.
Taiwan (CSNN) :Not determined.
CAS number
WARNING: This product contains a chemical known to the State of California to cause cancer.
WARNING: This product contains less than 1% of a chemical known to the State of California to cause birth defects or other reproductive
harm.
California Prop. 65
State regulations
Styrene – 1000 lbs. (453.6 kg)
Methyl Methacrylate – 1000 lbs. (453.6 kg)
CERCLA RQ –
Section 16. Other information
History
Date of issue
Version
Date of previous issue
:
:
:
02/01/2017
05/26/2015
2.0
2
3
2
National Fire Protection Association (U.S.A.)
Health
Special
Instability/Reactivity
Flammability
Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency Response Copyright 1997, National Fire Protection Association, Quincy, MA 02269. This
reprinted material is not the complete and official position of the National Fire Protection Association, on the referenced subject which is represented only by the standard in its entirety.
Copyright 2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to be interpreted and applied only by properly trained individuals to identify fire, health and
reactivity hazards of chemicals. The user is referred to certain limited number of chemicals with recommended classifications in NFPA 49 and NFPA 325, which would be used as a guideline only.
Whether the chemicals are classified by NFPA or not, anyone using the 704 systems to classify chemicals does so at their own risk.
AOC Corporate Regulatory Affairs
Page: 9 of 10G440LU
Section 16. Other information
The information contained in this data sheet is furnished in good faith and without warranty, representation, or inducement or license of any kind,
except that it is accurate to the best of AOC, LLC’s knowledge, or was obtained from sources believed by AOC, LLC to be reliable. The
accuracy, adequacy or completeness of health and safety precautions set forth herein cannot be guaranteed, and the buyer is solely
responsible for ensuring that the product is used, handled, stored, and disposed of safely and in compliance with applicable federal, state or
provincial, and local laws. AOC, LLC disclaims liability for any loss, damage or personal injury that arises from, or is in any way related to, use
of the information contained in this data sheet.
Notice to reader
Indicates information that has changed from previously issued version.
Key to abbreviations :ATE = Acute Toxicity Estimate
BCF = Bioconcentration Factor
GHS = Globally Harmonized System of Classification and Labelling of Chemicals
IATA = International Air Transport Association
IBC = Intermediate Bulk Container
IMDG = International Maritime Dangerous Goods
LogPow = logarithm of the octanol/water partition coefficient
MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by
the Protocol of 1978. (“Marpol” = marine pollution)
UN = United Nations
This Safety Data Sheet (SDS) and its content are the confidential and proprietary information of AOC and it may not be modified, altered,
deconstructed, or presented in any other manner, without the explicit authorization of AOC and/or its legal counsel.
Page: 10 of 10G440LU
by | Sep 27, 2025
by | Sep 27, 2025
HV FAST BONDING PUTTY
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
Date of issue: 08/11/2016 Revision date: 08/11/2016 Supersedes: 09/10/2014
08/11/2016 EN (English US) Page 1
SECTION 1: Identification of the substance/mixture and of the company/undertaking
1.1. Product identifier
Product form : Mixture
Trade name : HV FAST BONDING PUTTY
CAS No : mixture
Product code : 804-025
Formula : na
1.2. Relevant identified uses of the substance or mixture and uses advised against
Use of the substance/mixture : BONDING PUTTY
1.3. Details of the supplier of the safety data sheet
Dura Technologies, Inc.
2720 South Willow Avenue #A
Bloomington, CA 92316
909.877.8477
ChemTrec US: 800.424.9300
ChemTrec Int: +1 70 3527 3887
1.4. Emergency telephone number
Emergency number : ChemTrec US: 800.424.9300 Int: +1 70 3527 3887
CHEMTREC: 1-800-424-9300
SECTION 2: Hazards identification
2.1. Classification of the substance or mixture
GHS-US classification
Flam. Liq. 3 H226
Skin Irrit. 2 H315
Eye Irrit. 2A H319
Carc. 2 H351
Repr. 2 H361
STOT SE 3 H335
STOT RE 1 H372
2.2. Label elements
GHS-US labeling
Hazard pictograms (GHS-US) :
GHS02
GHS07
GHS08
Signal word (GHS-US) : Danger
Hazard statements (GHS-US) : H226 – Flammable liquid and vapor
H315 – Causes skin irritation
H319 – Causes serious eye irritation
H335 – May cause respiratory irritation
H351 – Suspected of causing cancer
H361 – Suspected of damaging fertility or the unborn child
H372 – Causes damage to organs through prolonged or repeated exposure
Precautionary statements (GHS-US) : P201 – Obtain special instructions before use
P202 – Do not handle until all safety precautions have been read and understood
P210 – Keep away from heat, hot surfaces, open flames, sparks. – No smoking
P233 – Keep container tightly closed
P240 – Ground/bond container and receiving equipment
P241 – Use explosion-proof electrical, lighting, ventilating equipment
P242 – Use only non-sparking tools
P243 – Take precautionary measures against static discharge
P260 – Do not breathe dust/fume/gas/mist/vapors/spray
HV FAST BONDING PUTTY
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
08/11/2016 EN (English US) 2/10
P261 – Avoid breathing dust/fume/gas/mist/vapors/spray
P264 – Wash EXPOSED AREA. thoroughly after handling
P270 – Do not eat, drink or smoke when using this product
P271 – Use only outdoors or in a well-ventilated area
P280 – Wear eye protection, protective clothing, protective gloves
P302+P352 – IF ON SKIN: Wash with plenty of soap and water
P303+P361+P353 – IF ON SKIN (or hair): Remove/Take off immediately all contaminated
clothing. Rinse skin with water/shower
P304+P340 – IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable
for breathing
P305+P351+P338 – If in eyes: Rinse cautiously with water for several minutes. Remove contact
lenses, if present and easy to do. Continue rinsing
P308+P313 – IF exposed or concerned: Get medical advice/attention
P312 – Call a POISON CENTER or doctor/physician if you feel unwell
P314 – Get medical advice and attention if you feel unwell
P321 – Specific treatment (see SEEK MEDICAL AID. on this label)
P332+P313 – If skin irritation occurs: Get medical advice/attention
P337+P313 – If eye irritation persists: Get medical advice/attention
P362 – Take off contaminated clothing and wash it before reuse
P370+P378 – In case of fire: Use carbon dioxide (CO2), dry chemical powder, foam to
extinguish
P403+P233 – Store in a well-ventilated place. Keep container tightly closed
P403+P235 – Store in a well-ventilated place. Keep cool
P405 – Store locked up
P501 – Dispose of contents/container to LOCAL, STATE, AND NATIONAL REGULATIONS.
2.3. Other hazards
No additional information available
2.4. Unknown acute toxicity (GHS-US)
No data available
SECTION 3: Composition/Information on ingredients
3.1. Substance
Not applicable
Full text of H-phrases: see section 16
3.2. Mixture
Name Product identifier % GHS-US classification
Unsaturated Polyester Resin (CAS No) TRADE SECRET <= 38 Not classified
styrene, inhibited (CAS No) 100-42-5 <= 22 Flam. Liq. 3, H226
Acute Tox. 4 (Inhalation:vapour),
H332
Skin Irrit. 2, H315
Eye Irrit. 2A, H319
Carc. 2, H351
Repr. 2, H361
STOT SE 3, H335
STOT RE 1, H372
fibreglass, diameter > 3 micrometers, length > 5 micrometers (CAS No) 65997-17-3 <= 22 Not classified
talc (CAS No) 14807-96-6 <= 12 Not classified
cobalt(II) 2-ethylhexanoate (CAS No) 136-52-7 <= 0.5 Carc. 2, H351
SECTION 4: First aid measures
4.1. Description of first aid measures
First-aid measures general : Never give anything by mouth to an unconscious person. Suspected of causing cancer. IF
exposed or concerned: Get medical advice/attention.
First-aid measures after inhalation : Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a
POISON CENTER or doctor/physician if you feel unwell.
First-aid measures after skin contact : Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower. Wash
with plenty of soap and water. Wash contaminated clothing before reuse. If skin irritation occurs:
Get medical advice/attention. Specific treatment (see ... on this label).
First-aid measures after eye contact : Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to
do. Continue rinsing. If eye irritation persists: Get medical advice/attention.
First-aid measures after ingestion : Rinse mouth. Do NOT induce vomiting. Obtain emergency medical attention.
HV FAST BONDING PUTTY
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
08/11/2016 EN (English US) 3/10
4.2. Most important symptoms and effects, both acute and delayed
Symptoms/injuries : May cause genetic defects (avoid skin contact and inhalation.). May cause cancer (avoid skin
contact and inhalation.). Suspected of damaging fertility or the unborn child. Causes damage to
organs through prolonged or repeated exposure.
Symptoms/injuries after inhalation : Danger of serious damage to health by prolonged exposure through inhalation. Harmful if
inhaled. May cause respiratory irritation.
Symptoms/injuries after skin contact : Causes skin irritation.
Symptoms/injuries after eye contact : Causes serious eye irritation.
4.3. Indication of any immediate medical attention and special treatment needed
No additional information available
SECTION 5: Firefighting measures
5.1. Extinguishing media
Suitable extinguishing media : Foam. Dry powder. Carbon dioxide. Water spray. Sand.
Unsuitable extinguishing media : Do not use a heavy water stream.
5.2. Special hazards arising from the substance or mixture
Fire hazard : Highly flammable liquid and vapor. Flammable liquid and vapor.
Explosion hazard : May form flammable/explosive vapor-air mixture.
Reactivity : No reactivity hazard other than the effects described in sub-sections below.
5.3. Advice for firefighters
Firefighting instructions : Use water spray or fog for cooling exposed containers. Exercise caution when fighting any
chemical fire. Prevent fire-fighting water from entering environment.
Protection during firefighting : Do not enter fire area without proper protective equipment, including respiratory protection.
SECTION 6: Accidental release measures
6.1. Personal precautions, protective equipment and emergency procedures
General measures : Remove ignition sources. Use special care to avoid static electric charges. No open flames. No
smoking.
6.1.1. For non-emergency personnel
Protective equipment : Gloves. Protective goggles. Protective clothing.
Emergency procedures : Evacuate unnecessary personnel.
6.1.2. For emergency responders
Protective equipment : Equip cleanup crew with proper protection.
Emergency procedures : Ventilate area.
6.2. Environmental precautions
Prevent entry to sewers and public waters. Notify authorities if liquid enters sewers or public waters.
6.3. Methods and material for containment and cleaning up
For containment : Dam up the liquid spill. Contain released substance, pump into suitable containers.
Methods for cleaning up : Soak up spills with inert solids, such as clay or diatomaceous earth as soon as possible. Collect
spillage. Store away from other materials.
6.4. Reference to other sections
See Heading 8. Exposure controls and personal protection.
SECTION 7: Handling and storage
7.1. Precautions for safe handling
Additional hazards when processed : Handle empty containers with care because residual vapors are flammable.
Precautions for safe handling : Use only outdoors or in a well-ventilated area. Avoid breathing DUST, FUMES, MIST, OR
VAPORS. Obtain special instructions before use. Do not handle until all safety precautions have
been read and understood. Eliminate all ignition sources if safe to do so. Wash hands and other
exposed areas with mild soap and water before eating, drinking or smoking and when leaving
work. Provide good ventilation in process area to prevent formation of vapor. No open flames. No
smoking. Take precautionary measures against static discharge. Use only non-sparking tools.
Do not breathe dust/fume/gas/mist/vapors/spray.
Hygiene measures : Wash ... thoroughly after handling. Do not eat, drink or smoke when using this product.
HV FAST BONDING PUTTY
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
08/11/2016 EN (English US) 4/10
7.2. Conditions for safe storage, including any incompatibilities
Technical measures : Proper grounding procedures to avoid static electricity should be followed. Ground/bond
container and receiving equipment. Use explosion-proof electrical/ventilating/lighting/
equipment.
Storage conditions : Keep in fireproof place. Keep only in the original container in a cool, well ventilated place away
from : Keep container tightly closed.
Incompatible products : Strong bases. Strong acids.
Incompatible materials : Sources of ignition. Direct sunlight. Heat sources.
7.3. Specific end use(s)
No additional information available
SECTION 8: Exposure controls/personal protection
8.1. Control parameters
styrene, inhibited (100-42-5)
USA ACGIH ACGIH TWA (ppm) 20 ppm
USA ACGIH ACGIH STEL (ppm) 20 ppm
talc (14807-96-6)
USA ACGIH ACGIH TWA (mg/m ) 2 mg/m
fibreglass, diameter > 3 micrometers, length > 5 micrometers (65997-17-3)
USA ACGIH ACGIH TWA (mg/m ) 5 mg/m
8.2. Exposure controls
Appropriate engineering controls : Ensure exposure is below occupational exposure limits (where available).
Personal protective equipment : Avoid all unnecessary exposure.
Hand protection : Wear protective gloves.
Eye protection : Chemical goggles or safety glasses.
Skin and body protection : Wear suitable protective clothing.
Respiratory protection : Wear appropriate mask.
Other information : Do not eat, drink or smoke during use.
SECTION 9: Physical and chemical properties
9.1. Information on basic physical and chemical properties
Physical state : Liquid
Color : Colourless to yellow.
Odor : characteristic.
Odor threshold : No data available
pH : No data available
Relative evaporation rate (butyl acetate=1) : No data available
Melting point : No data available
Freezing point : No data available
Boiling point : 64 C
Flash point : 30 – 34 C
Auto-ignition temperature : No data available
Decomposition temperature : No data available
Flammability (solid, gas) : No data available
Vapor pressure : No data available
Relative vapor density at 20 C : No data available
Relative density : No data available
Specific gravity / density : 1.43
Solubility : No data available
Log Pow : No data available
Log Kow : No data available
HV FAST BONDING PUTTY
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
08/11/2016 EN (English US) 5/10
Viscosity, kinematic : No data available
Viscosity, dynamic : No data available
Explosive properties : No data available
Oxidizing properties : No data available
Explosive limits : No data available
9.2. Other information
No additional information available
SECTION 10: Stability and reactivity
10.1. Reactivity
No reactivity hazard other than the effects described in sub-sections below.
10.2. Chemical stability
Polymerization can result in formation of solid deposits, even in vapour space. Highly flammable liquid and vapor. Not established. Flammable liquid and
vapor. May form flammable/explosive vapor-air mixture.
10.3. Possibility of hazardous reactions
Not established.
10.4. Conditions to avoid
Direct sunlight. Extremely high or low temperatures. Open flame. Overheating. Heat. Sparks.
10.5. Incompatible materials
Strong acids. Strong bases.
10.6. Hazardous decomposition products
fume. Carbon monoxide. Carbon dioxide. May release flammable gases.
SECTION 11: Toxicological information
11.1. Information on toxicological effects
Acute toxicity : Not classified
HV FAST BONDING PUTTY ( f )mixture
ATE CLP (vapors) 11.000 mg/l/4h
styrene, inhibited (100-42-5)
LD50 oral rat 5000 mg/kg (Rat; Literature study; >6000 mg/kg bodyweight; Rat; Weight of evidence)
LD50 dermal rat 2820 mg/kg (Rat; Literature study; OECD 402: Acute Dermal Toxicity; >2000 mg/kg
bodyweight; Rat; Experimental value)
LD50 dermal rabbit 5010 mg/kg (Rabbit; Literature study)
LC50 inhalation rat (mg/l) 12 mg/l/4h (Rat; Literature study)
LC50 inhalation rat (ppm) 2770 ppm/4h (Rat; Literature study)
ATE CLP (oral) 5000.000 mg/kg body weight
ATE CLP (dermal) 2820.000 mg/kg body weight
ATE CLP (gases) 2770.000 ppmV/4h
ATE CLP (vapors) 12.000 mg/l/4h
ATE CLP (dust, mist) 12.000 mg/l/4h
cobalt(II) 2-ethylhexanoate (136-52-7)
LD50 oral rat 3129 mg/kg body weight (Rat; OECD 425: Acute Oral Toxicity: Up-and-Down Procedure;
Experimental value)
LD50 dermal rat > 2000 mg/kg body weight (Rat; Weight of evidence; OECD 402: Acute Dermal Toxicity)
ATE CLP (oral) 3129.000 mg/kg body weight
Skin corrosion/irritation : Causes skin irritation.
Serious eye damage/irritation : Causes serious eye irritation.
Respiratory or skin sensitization : Not classified
Germ cell mutagenicity : Not classified
Carcinogenicity : Suspected of causing cancer.
styrene, inhibited (100-42-5)
IARC group 2B – Possibly carcinogenic to humans
HV FAST BONDING PUTTY
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
08/11/2016 EN (English US) 6/10
cobalt(II) 2-ethylhexanoate (136-52-7)
IARC group 2B – Possibly carcinogenic to humans
talc (14807-96-6)
IARC group 3 – Not classifiable
Reproductive toxicity : Suspected of damaging fertility or the unborn child.
Based on available data, the classification criteria are not met
Specific target organ toxicity (single exposure) : May cause respiratory irritation.
Specific target organ toxicity (repeated
exposure)
: Causes damage to organs through prolonged or repeated exposure.
Based on available data, the classification criteria are not met
Causes damage to organs through prolonged or repeated exposure
Aspiration hazard : Not classified
Based on available data, the classification criteria are not met
Potential Adverse human health effects and
symptoms
: Harmful if inhaled. Based on available data, the classification criteria are not met.
Symptoms/injuries after inhalation : Danger of serious damage to health by prolonged exposure through inhalation. Harmful if
inhaled. May cause respiratory irritation.
Symptoms/injuries after skin contact : Causes skin irritation.
Symptoms/injuries after eye contact : Causes serious eye irritation.
SECTION 12: Ecological information
12.1. Toxicity
styrene, inhibited (100-42-5)
LC50 fish 1 25 mg/l (96 h; Lepomis macrochirus; GLP)
LC50 other aquatic organisms 1 10 – 100 mg/l (96 h)
EC50 Daphnia 1 23 mg/l (48 h; Daphnia magna; Locomotor effect)
LC50 fish 2 32 mg/l (96 h; Pimephales promelas)
EC50 Daphnia 2 27 mg/l (24 h; Daphnia magna; GLP)
TLM fish 1 25.1 mg/l (96 h; Lepomis macrochirus; Soft water)
TLM fish 2 46.4 mg/l (96 h; Pimephales promelas; Soft water)
TLM other aquatic organisms 1 10 – 100,96 h
Threshold limit other aquatic organisms 1 10 – 100,96 h; Pseudomonas putida
Threshold limit other aquatic organisms 2 72 mg/l
Threshold limit algae 1 > 200 mg/l (192 h; Scenedesmus quadricauda; Inhibitory)
Threshold limit algae 2 67 mg/l (Microcystis aeruginosa; Inhibitory)
cobalt(II) 2-ethylhexanoate (136-52-7)
LC50 fish 1 54.1 mg/l (96 h; Pimephales promelas)
EC50 Daphnia 1 2618 g/l (48 h)
Threshold limit algae 1 24.1 g/l (7 days)
Threshold limit algae 2 90.1 g/l (7 days; Lemna minor; Growth rate)
talc (14807-96-6)
LC50 fish 1 > 100 g/l (24 h; Brachydanio rerio; Intermittent flow)
12.2. Persistence and degradability
HV FAST BONDING PUTTY (mixture)
Persistence and degradability Not established.
styrene, inhibited (100-42-5)
Persistence and degradability Readily biodegradable in water. Not readily biodegradable in water. Forming sediments in
water. Non degradable in the soil. Adsorbs into the soil. Photodegradation in the air. Not
established.
Chemical oxygen demand (COD) 2.80 g O /g substance
ThOD 3.07 g O /g substance
BOD (% of ThOD) 0.42 % ThOD
HV FAST BONDING PUTTY
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
08/11/2016 EN (English US) 7/10
cobalt(II) 2-ethylhexanoate (136-52-7)
Persistence and degradability Biodegradability in water: no data available.
talc (14807-96-6)
Persistence and degradability Biodegradability: not applicable.
Biochemical oxygen demand (BOD) Not applicable
Chemical oxygen demand (COD) Not applicable
ThOD Not applicable
BOD (% of ThOD) Not applicable
fibreglass, diameter > 3 micrometers, length > 5 micrometers (65997-17-3)
Persistence and degradability Biodegradability: not applicable. Not established.
Biochemical oxygen demand (BOD) Not applicable
Chemical oxygen demand (COD) Not applicable
ThOD Not applicable
BOD (% of ThOD) Not applicable
Unsaturated Polyester Resin (TRADE SECRET)
Persistence and degradability Not established.
12.3. Bioaccumulative potential
HV FAST BONDING PUTTY (mixture)
Bioaccumulative potential Not established.
styrene, inhibited (100-42-5)
BCF fish 1 35.5 (Carassius auratus)
BCF other aquatic organisms 1 74
Log Pow 2.96 (Experimental value; OECD 107: Partition Coefficient (n-octanol/water): Shake Flask
Method; 25 C)
Bioaccumulative potential Low potential for bioaccumulation (BCF < 500). Not established.
cobalt(II) 2-ethylhexanoate (136-52-7)
Bioaccumulative potential No bioaccumulation data available.
fibreglass, diameter > 3 micrometers, length > 5 micrometers (65997-17-3)
Bioaccumulative potential No bioaccumulation data available. Not established.
Unsaturated Polyester Resin (TRADE SECRET)
Bioaccumulative potential Not established.
12.4. Mobility in soil
styrene, inhibited (100-42-5)
Surface tension 0.032 N/m (19 C)
cobalt(II) 2-ethylhexanoate (136-52-7)
Surface tension 0.064 N/m (20 C; 1 g/l)
12.5. Other adverse effects
Other information : Avoid release to the environment.
SECTION 13: Disposal considerations
13.1. Waste treatment methods
Waste disposal recommendations : Dispose in a safe manner in accordance with local/national regulations. Dispose of
contents/container to …
Additional information : Handle empty containers with care because residual vapors are flammable.
Ecology – waste materials : Avoid release to the environment.
SECTION 14: Transport information
In accordance with DOT
UN-No.(DOT) : UN1866
Proper Shipping Name (DOT) : RESIN SOLUTION
HV FAST BONDING PUTTY
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
08/11/2016 EN (English US) 8/10
Transport hazard class(es) (DOT) : 3 – Class 3 – Flammable and combustible liquid 49 CFR 173.120
Hazard labels (DOT) : 3 – Flammable liquid
Packing group (DOT) : III – Minor Danger
Additional information
Other information : No supplementary information available.
ADR
Transport document description : UN 1866, 3, III, (D/E)
Packing group (ADR) : III
Class (ADR) : 3 – Flammable liquid
Hazard identification number (Kemler No.) : 33
Classification code (ADR) : F1
Hazard labels (ADR) : 3 – Flammable liquids
Orange plates :
Tunnel restriction code : D/E
LQ : 5l
Excepted quantities (ADR) : E2
Transport by sea
UN-No. (IMDG) : 1866
Proper Shipping Name (IMDG) : RESIN SOLUTION
Class (IMDG) : 3 – Flammable liquids
Packing group (IMDG) : III – substances presenting low danger
Air transport
UN-No. (IATA) : 1866
Proper Shipping Name (IATA) : RESIN SOLUTION
Class (IATA) : 3 – Flammable Liquids
Packing group (IATA) : III – Minor Danger
SECTION 15: Regulatory information
15.1. US Federal regulations
styrene, inhibited (100-42-5)
RQ (Reportable quantity, section 304 of EPA’s
List of Lists)
1000 lb
SARA Section 311/312 Hazard Classes Immediate (acute) health hazard
Reactive hazard
Fire hazard
Delayed (chronic) health hazard
15.2. International regulations
CANADA
No additional information available
HV FAST BONDING PUTTY
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
08/11/2016 EN (English US) 9/10
EU-Regulations
No additional information available
Classification according to Regulation (EC) No. 1272/2008 [CLP]
Flam. Liq. 3 H226
Acute Tox. 4 (Inhalation:vapour) H332
Skin Irrit. 2 H315
Eye Irrit. 2 H319
Muta. 1B H340
Carc. 1B H350
Full text of H-phrases: see section 16
Classification according to Directive 67/548/EEC [DSD] or 1999/45/EC [DPD]
Carc.Cat.2; R45
Muta.Cat.2; R46
F; R11
Xn; R20
Xi; R36/38
Full text of R-phrases: see section 16
15.2.2. National regulations
styrene, inhibited (100-42-5)
Listed on EPA’s Hazardous Air Pollutants (HAPS)
15.3. US State regulations
styrene, inhibited (100-42-5)
U.S. – California –
Proposition 65 –
Carcinogens List
U.S. – California –
Proposition 65 –
Developmental Toxicity
U.S. – California –
Proposition 65 –
Reproductive Toxicity –
Female
U.S. – California –
Proposition 65 –
Reproductive Toxicity – Male
Non-significant risk level
(NSRL)
styrene, inhibited (100-42-5)
U.S. – Massachusetts – Right To Know List
U.S. – New Jersey – Right to Know Hazardous Substance List
U.S. – Pennsylvania – RTK (Right to Know) – Environmental Hazard List
SECTION 16: Other information
Other information : None.
Full text of H-phrases: see section 16:
—— Acute Tox. 4 (Inhalation:vapour) Acute toxicity (inhalation:vapour) Category 4
—— Carc. 2 Carcinogenicity Category 2
—— Eye Irrit. 2A Serious eye damage/eye irritation Category 2A
—— Flam. Liq. 3 Flammable liquids Category 3
—— Repr. 2 Reproductive toxicity Category 2
—— Skin Irrit. 2 Skin corrosion/irritation Category 2
—— STOT RE 1 Specific target organ toxicity (repeated exposure) Category 1
—— STOT SE 3 Specific target organ toxicity (single exposure) Category 3
—— H226 Flammable liquid and vapor
—— H315 Causes skin irritation
—— H319 Causes serious eye irritation
—— H332 Harmful if inhaled
HV FAST BONDING PUTTY
Safety Data Sheet
according to Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules and Regulations
08/11/2016 EN (English US) 10/10
—— H335 May cause respiratory irritation
—— H351 Suspected of causing cancer
—— H361 Suspected of damaging fertility or the unborn child
—— H372 Causes damage to organs through prolonged or repeated exposure
NFPA health hazard : 2 – Intense or continued exposure could cause temporary
incapacitation or possible residual injury unless prompt
medical attention is given.
NFPA fire hazard : 3 – Liquids and solids that can be ignited under almost all
ambient conditions.
NFPA reactivity : 2 – Normally unstable and readily undergo violent
decomposition but do not detonate. Also: may react
violently with water or may form potentially explosive
mixtures with water.
HMIS III Rating
Health : 2 Moderate Hazard – Temporary or minor injury may occur
Flammability : 3 Serious Hazard
Physical : 1 Slight Hazard
Personal Protection : H
SDS US (GHS HazCom 2012)
To the best of our knowledge this SDS is accurate. The the extent allowed by law, this statement is made in lieu of an other warranties, expressed or implied including but not limited to any implied
warranty of merchantability or fitness for a particular purpose and is in lieu of any other obligations or liability on the part of Dura Technoligies, Inc.
